Large Current External FET Controller Type Switching Regulators
Dual-output Step-up, Negative Voltage, Step-down Switching Regulators (Controller type)
Sep. 2008
2/16
3/16
4/16
5/16
6/16
7/16
8/16
9/16
4) SCP Comp ( Timer-latch type short-circuit prevention circuit ) When the output voltage malfunctions because of a short circuit, this function is used to turn OFF the output transistor forcedly, in order to protect the system. If the output voltage drops in realtion to the set voltage level, an error will be amplified through the Err Amp and the voltage at the FB1/FB2 pins will reach the low voltage side. If SCP Comp sets the voltage below the threshold level for either the FB1 or FB2, (i.e., 1.05Vtype for the BA9741F/FS / BA9743AFV or 0.25Vtype for the BA9744FV), the short prevention circuit will be activated to start the charging of the capacitor of SCP pin. When VIT=1.64Vtyp for the BA9741F/FS / BA9743AFV or VIT=1.18Vtyp for the BA9744FV is achieved, the output transistor will turn OF F. The time is set by the capacitor (Cscp) connected to the SCP pin (pin 15) . The time TSCP is obtained by the formula shown below: T SCP = V IT +V STB . Cscp I SCP
For example, in the case of the BA9743AFV, assuming that C SCP =0.1μ F, V IT =1.64 V, V STB =0.05V and I SCP =2.5μA.
T SCP =
1.64 - 0.05 2.5μ
×0.1μ = 63.6mS
In order to stop the function of the short prevention circuit, short-circuit the SC P pin to GND .
5) PWM Comp 1/2 DEAD TIME (Rest period adjustment circuit / Dead time) This function can be set by dividing the resistance of DT1 and DT2 pins (pins 6 and 11) between V REF and GND. With PWM Comp, comparing the dead time voltage input and the error voltage from the Err Amp with the triangular wave, the output drive transistors are turned ON/OFF. When Dead time voltage>Error voltage, the output duty is determined by the dead time voltage. The dead time voltage VDT is obtained by the expression shown below. VDT = V REF . R2 R1 + R2 (BA9744FV) When VDT=0.49Vtyp: Duty 100% When VDT=1.01Vtyp: Duty 0% (Provided, however, that fosc=10kHz )
(BA9741F/FS/BA9743AFV) When VDT=1.48Vtyp: Duty 100% When VDT=1.97Vtyp: Duty 0% (Provided, however, that fosc=10kHz)
Note: If the oscillation frequency is at a high level, the upper/lower limits (Vt0/Vt100) of the triangular wave will be shifted in the direction in which the amplitude is developed. 6) PWM Comp 1/2 SS (Soft start function) By connecting the resistors R1 and R2, and the capacitor CD T to D T pins (pins 6 and 11), as shown in figure on the right, the soft start function is enabled.
7) Handling of pins of unused channel
Fig.35
Vcc
BA9741F/FS, BA9743AFV
BA9744FV
Fig.36
If channel 1 is only used, the unused channel should be handled as shown above.
Fig.37
Ordering part number
B
A
9
Part No. 9743 9744 9741
7
4
3
F
V
-
E
2
Part No.
Package F: SOP16 (BA9741F) FS: SSOP-A16 (BA9741FS) AFV: SSOP-B16 (BA9743AFV) FV: SSOP-B16 (BA9744FV)
Packaging and forming specification E2: Embossed tape and reel
Catalog No.08T678A '08.9 ROHM ©
Appendix
Notes
No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM CO.,LTD. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact your nearest sales office.
ROHM Customer Support System
www.rohm.com
Copyright © 2009 ROHM CO.,LTD.
THE AMERICAS / EUROPE / ASIA / JAPAN
Contact us : webmaster @ rohm.co. jp
21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan
TEL : +81-75-311-2121 FAX : +81-75-315-0172
Appendix-Rev4.0
