BD11600NUX-E2

USB Switch ICs DPDT Type (Double Pole Double Throw) BD11600NUX No.11103EAT03 ●Description BD11600NUX is DPDT analog switches handling with USB2.0 high-speed that have both a low resistance and a low capacitance. Moreover, this is widely guaranteed from 2.5V to 5.5V as for the range of the power-supply voltage. This has a low consumption mode by making OE “H” and the multi-selector by making the combination of OE “L” and S. The electrostatic discharge protection circuit is built-in in all terminals. ●Features 1) VCC Operation from 2.5V to 5.5V. 2) 3Ω switches between the input to the output. 3) Low Capacity 2ch Analog SW. 4) 10-Pin SON Package. (3.0mm x 2.0mm, Height=0.6mm, 0.5mm pitch) ●Applications Digital Still Cameras, Digital Video Camcorders, Portable Navigation Devices, TV, Portable DVD Players, Portable Game Systems, Personal computers, PDA, Mobile phones ●Line up matrix BD11600NUX Parameter Supply Quiescent Current BD11601NUX 18 µA Input voltage range 2.5～5.5 V 3 Ω Switch ON Resistance ( VIN=0 V ) Switch ON Capacitance 2.5 Ω 6 pF Configuration Package DPDT DPST VSON010X3020 VSON008X2020 ●Absolute maximum ratings (Ta=25℃) Parameter Symbol Ratings Unit Conditions Input supply voltage Vmax -0.5～7.0 V D+,D-,1D+,1D-,2D+,2D- Pins Input supply voltage Vmax -0.3～7.0 V Other Pins Pd 1.925 W *1 Operating temperature range Topr -40～+85 ℃ Storage temperature range Tstr -55～+150 ℃ Power dissipation *1 When using more than at Ta=25℃, it is reduced 15.4 mW per 1℃. ROHM specification board 70mm×70mm mounting. ●Operating conditions (Ta=-40～+85℃) Parameter Input voltage range (VCC) Symbol Ratings Unit VCC 2.5～5.5 V Conditions * This product does not especially designed to be protected from radioactivity. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 1/10 2011.08 - Rev.A Technical Note BD11600NUX ●Electrical characteristics (Unless otherwise noted, Ta = 25C, VCC=5.0V) Limits Parameter Symbol Min. Typ. Max. Unit Conditions Supply Quiescent Current 1 ICC1 - 1 3 µA SW1, 2=OFF Supply Quiescent Current 2 ICC2 - 18 40 µA SW1=ON Supply Quiescent Current 3 ICC3 - 19 40 µA SW2=ON Ron1 - 3 6 Ω VIN=0V Ron2 - 3.5 6 Ω VIN=2.4V Off-Leakage Current Ioff -2 0 2 µA SW1, 2=OFF On-Leakage Current Ion -2 0 2 µA VCC>VIN, SW1, 2=ON Switch Input Range VIN -0.5 - 5.5 V SW1, 2=ON Coff - 4 - pF Con - 6 - pF Input “L” level (S, OE ) VIL - - 0.5 V Input “H” level (S, OE ) VIH 1.1 - - V Switch ON Resistance 1 (SW1, 2) Switch ON Resistance 2 (SW1, 2) Switch OFF Capacitance (SW1, 2) Switch ON Capacitance (SW1, 2) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 2/10 2011.08 - Rev.A Technical Note BD11600NUX ●Electrical characteristic curves (Reference data) Fig.2 Eye Pattern High Speed Fig.1 Eye Pattern Full Speed 40 3 35 2.5 30 25 ICC2 (uA) ICC1 (uA) 2 1.5 20 15 Ta=105°C 1 Ta=25°C Ta=105° 10 Ta=-60° Ta=25° 0.5 Ta=-60°C 5 VCC=0V~7V S=L, OE=L VCC=0V~7V S=L, OE=H 0 0 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 0 7 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 VCC (V) VCC (V) Fig.3 ICC vs Input Voltage (SW OFF) Fig.4 ICC vs Input Voltage (SW ON) 6 6.5 7 5 7 6 4 5 I_1D+ (uA) RON [Ω] 3 4 Ta=105℃ 2 3 Ta=25℃ 2 Ta=-60℃ 1 Ta=25°C Ta=-60°C Ta=105°C 1 VCC=5V,IO(D+)=-10mA, VIN=0~7V,S=L,OE=L 0 0 0 0 1 2 3 4 5 6 7 1 2 3 4 5 6 7 1D+ (V) 1D+ [V] Fig.5 Ron vs Input Voltage www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. Fig.6 Leak current vs Input Voltage(SW OFF) 3/10 2011.08 - Rev.A Technical Note BD11600NUX ●Block diagram and pin configuration １D+ 1 10 VCC １D- 2 9 S 2D+ 3 8 D+ 2D- 4 7 D- GND 5 6 OE Fig.8 Pin configuration Fig.7 Block diagram ●Package Dimensions B D 1 1 6 0 0 N LOT No. Fig.9 Package Dimensions www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 4/10 2011.08 - Rev.A Technical Note BD11600NUX ●Pin Description Pin NO. Terminal circuit Pin Name I／O 1 A 1D+ O 2 B 1D- O 3 C 2D+ O 4 D 2D- O 5 - GND - Ground Pin. 6 E OE I Bus-Switch Analog Pin. 7 F D- I 8 G D+ I 9 H S I Select Input Pin. 10 - VCC - Power Supply. OE S SW1 SW2 Signal Pass H L OFF OFF ALL OFF H H OFF OFF ALL OFF L L ON OFF 1D+⇔D+, 1D-⇔D- L H OFF ON 2D+⇔D+, 2D-⇔D- Function Analog SW terminal. Analog SW terminal. ●Truth Table ●Equivalent Circuit A,B,C,D F,G PIN PIN E,H VCC PIN www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 5/10 2011.08 - Rev.A Technical Note BD11600NUX ●How to select parts of application VCC SW1 High Speed USB TRANSCEIVER 1D+ D+ 1D- D- USB Connector SW2 2D+ High Speed USB TRANSCEIVER 2D- Control OE S GND Fig.10 Application circuit of multi-USB TRANSCEIVER VCC SW1 High Speed USB TRANSCEIVER D+ 1D+ D- 1D- USB HOST1 SW2 2D+ 2D- OE S USB HOST2 Control GND Fig.11 Application circuit of two communicating with two USB HOST www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 6/10 2011.08 - Rev.A Technical Note BD11600NUX ●Parameter Measurement Information VCC 1D+ D+ 2D+ VIN IIN Control OE S GND Fig.12 SW1 ON-State ICC Fig.13 ON-State Resistance (Ron) Fig.14 OFF-State Leakage current Fig.15 ON-State Leakage current www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 7/10 2011.08 - Rev.A Technical Note BD11600NUX ●Notes for use (1) Absolute maximum ratings If applied voltage (VCC), operating temperature range (Topr), or other absolute maximum ratings are exceeded, there is a risk of damage. Since it is not possible to identify short, open, or other damage modes, if special modes in which absolute maximum ratings are exceeded are assumed, consider applying fuses or other physical safety measures. (2) Recommended operating range This is the range within which it is possible to obtain roughly the expected characteristics. For electrical characteristics, it is those that are guaranteed under the conditions for each parameter. Even when these are within the recommended operating range, voltage and temperature characteristics are indicated. (3) Reverse connection of power supply connector There is a risk of damaging the LSI by reverse connection of the power supply connector. For protection from reverse connection, take measures such as externally placing a diode between the power supply and the power supply pin of the LSI. (4) Power supply lines In the design of the board pattern, make power supply and GND line wiring low impedance. When doing so, although the digital power supply and analog power supply are the same potential, separate the digital power supply pattern and analog power supply pattern to deter digital noise from entering the analog power supply due to the common impedance of the wiring patterns. Similarly take pattern design into account for GND lines as well. Furthermore, for all power supply pins of the LSI, in conjunction with inserting capacitors between power supply and GND pins, when using electrolytic capacitors, determine constants upon adequately confirming that capacitance loss occurring at low temperatures is not a problem for various characteristics of the capacitors used. (5) GND voltage Make the potential of a GND pin such that it will be the lowest potential even if operating below that. In addition, confirm that there are no pins for which the potential becomes less than a GND by actually including transition phenomena. (6) Shorts between pins and misinstallation When installing in the set board, pay adequate attention to orientation and placement discrepancies of the LSI. If it is installed erroneously, there is a risk of LSI damage. There also is a risk of damage if it is shorted by a foreign substance getting between pins or between a pin and a power supply or GND. (7) Operation in strong magnetic fields Be careful when using the LSI in a strong magnetic field, since it may malfunction. (8) Inspection in set board When inspecting the LSI in the set board, since there is a risk of stress to the LSI when capacitors are connected to low impedance LSI pins, be sure to discharge for each process. Moreover, when getting it on and off of a jig in the inspection process, always connect it after turning off the power supply, perform the inspection, and remove it after turning off the power supply. Furthermore, as countermeasures against static electricity, use grounding in the assembly process and take appropriate care in transport and storage. (9) Input pins Parasitic elements inevitably are formed on an LSI structure due to potential relationships. Because parasitic elements operate, they give rise to interference with circuit operation and may be the cause of malfunctions as well as damage. Accordingly, take care not to apply a lower voltage than GND to an input pin or use the LSI in other ways such that parasitic elements operate. Moreover, do not apply a voltage to an input pin when the power supply voltage is not being applied to the LSI. Furthermore, when the power supply voltage is being applied, make each input pin a voltage less than the power supply voltage as well as within the guaranteed values of electrical characteristics. (10) Ground wiring pattern When there is a small signal GND and a large current GND, it is recommended that you separate the large current GND pattern and small signal GND pattern and provide single point grounding at the reference point of the set so that voltage variation due to resistance components of the pattern wiring and large currents do not cause the small signal GND voltage to change. Take care that the GND wiring pattern of externally attached components also does not change. (11) Externally attached capacitors When using ceramic capacitors for externally attached capacitors, determine constants upon taking into account a lowering of the rated capacitance due to DC bias and capacitance change due to factors such as temperature. (12) Thermal design Perform thermal design in which there are adequate margins by taking into account the permissible dissipation (Pd) in actual states of use. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 8/10 2011.08 - Rev.A Technical Note BD11600NUX ●Power Dissipation 2.4 2.2 Pd=1.925W Power dissipation :Pd [W] 2 1.8 1.6 -15.4mW/℃ 1.4 1.2 1 0.8 0.6 0.4 0.2 Ta_max=85℃ 0 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 Ambient temperature :Ta [℃] Fig.16 Power dissipation www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 9/10 2011.08 - Rev.A Technical Note BD11600NUX ●Ordering part number B D 1 Part No. 1 6 0 0 N Part No. U X - Package NUX:VSON010X3020 E 2 Packaging and forming specification E2: Embossed tape and reel VSON010X3020 2.0±0.1 3.0±0.1 0.6MAX 0.4±0.1 0.5±0.1 1 5 6 10 E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand ) (0.12) +0.03 0.02 −0.02 S 2.0±0.1 4000pcs 0.64±0.1 C0.2 Embossed carrier tape Quantity Direction of feed 1PIN MARK 0.05 S Tape +0.05 0.25 −0.04 2.39±0.1 www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 1pin (Unit : mm) Reel 10/10 Direction of feed ∗ Order quantity needs to be multiple of the minimum quantity. 2011.08 - Rev.A Datasheet Notice Precaution on using ROHM Products 1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you (Note 1) , transport intend to use our Products in devices requiring extremely high reliability (such as medical equipment equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅢ CLASSⅣ CLASSⅢ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice - GE © 2014 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act, please consult with ROHM representative in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable for infringement of any intellectual property rights or other damages arising from use of such information or data.: 2. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the information contained in this document. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice - GE © 2014 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s representative. 3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. Notice – WE © 2014 ROHM Co., Ltd. All rights reserved. Rev.001