BD2221G-TR

Datasheet 1ch Small Package High Side Switch ICs 0.75A Current Limit Latch Off High Side Switch ICs BD2220G BD2221G General Description Key Specifications ◼ ◼ ◼ ◼ ◼ BD2220G and BD2221G are low ON-Resistance N-Channel MOSFET high-side power switches, optimized for Universal Serial Bus (USB) applications. BD2220G and BD2221G are equipped with the function of over-current detection, thermal shutdown, under-voltage lockout and soft-start. Input Voltage Range: 2.7V to 5.5V ON-Resistance: 160mΩ(Typ) Over-Current Threshold: 0.5A (Min), 1.0A (Max) Standby Current: 0.01μA (Typ) Operating Temperature Range: -40°C to +85°C Package W(Typ) D (Typ) H (Max) Features ■ Low ON-Resistance (Typ 160mΩ) N-Channel MOSFET Built-in Over-Current Detection (Output OFF-Latch Operation) Thermal Shutdown Open-Drain Fault Flag Output Flag Output Delay Under-Voltage Lockout Soft-Start Circuit Control Input Logic ➢ Active-High : BD2220G ➢ Active-Low : BD2221G Reverse Current Protection when Power Switch Off ■ ■ ■ ■ ■ ■ ■ ■ SSOP5 2.90mm x 2.80mm x 1.25mm Applications USB hub in consumer appliances, PC, PC peripheral equipment, and so forth Typical Application Circuit 5V (Typ.) 5V(Typ) 3.3V CIN VIN IN VOUT OUT + GND 10kΩ~ 10kΩ to 100kΩ 100kΩ CL - EN /OC Lineup Min Over-Current Threshold Typ Max Control Input Logic Package Orderable Part Number 0.5A - 1.0A High SSOP5 Reel of 3000 BD2220G-TR 0.5A - 1.0A Low SSOP5 Reel of 3000 BD2221G-TR ○Product structure：Silicon monolithic integrated circuit www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･14･001 ○This product has not designed protection against radioactive rays 1/22 TSZ02201-0E3E0H300190-1-2 25.Jan.2021 Rev.004 BD2220G Datasheet BD2221G Block Diagram Over-Current Detection Delay Counter /OC S Q R Under-Voltage Lockout Charge Pump Thermal Shutdown GND EN(/EN) IN OUT Pin Configurations BD2220G TOP VIEW 1 IN BD2221G TOP VIEW 1 IN OUT 5 OUT 5 2 GND 2 GND 3 EN 3 /EN /OC 4 /OC 4 Pin Description Pin No. Symbol I/O 1 IN - Switch input and the supply voltage for the IC. 2 GND - Ground 3 EN, /EN I Enable input. EN: High level input turns on the switch. (BD2220G) /EN: Low level input turns on the switch. (BD2221G) 4 /OC O Over-current notification terminal. Low level output during over-current or over-temperature condition. Open-drain fault flag output. 5 OUT O Switch output www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 Function 2/22 TSZ02201-0E3E0H300190-1-2 25.Jan.2021 Rev.004 BD2220G Datasheet BD2221G Absolute Maximum Ratings (Ta=25°C) Parameter IN Supply Voltage EN(/EN) Input Voltage /OC Voltage /OC Sink Current Symbol Rating Unit VIN -0.3 to +6.0 V VEN, V/EN -0.3 to +6.0 V V/OC -0.3 to +6.0 V I/OC 5 mA OUT Voltage VOUT -0.3 to +6.0 V Storage Temperature Tstg -55 to +150 °C Power Dissipation Pd 0.67 (Note 1) W (Note 1) Mounted on 70mm x 70mm x 1.6mm glass epoxy board. Reduce 5.4mW per 1oC above 25oC. Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated over the absolute maximum ratings. Recommended Operating Conditions Parameter IN Operating Voltage Operating Temperature Rating Symbol Unit Min Typ Max VIN 2.7 5.0 5.5 V Topr -40 - +85 °C Electrical Characteristics BD2220G (VIN= 5V, Ta= 25°C, unless otherwise specified.) DC Characteristics Limit Parameter Symbol Min Typ Max Unit Conditions Operating Current IDD - 110 160 μA Standby Current ISTB - 0.01 5 μA VENH 2.0 - - V VEN = 5V VOUT = Open VEN = 0V VOUT = Open High Input VENL - - 0.8 V Low Input EN Input Leakage IEN -1.0 +0.01 +1.0 μA VEN = 0V or 5V ON-Resistance RON - 160 210 mΩ IOUT = 50mA Switch Leak Current ILSW - - 1.0 μA VEN = 0V, VOUT = 0V Reverse Leak Current IREV - - 1.0 μA VOUT = 5.5V, VIN = 0V Over-Current Threshold ITH 0.5 - 1.0 A EN Input Voltage Short Circuit Output Current /OC Output Low Voltage UVLO Threshold ISC 0.35 - - A VOUT = 0V, RMS V/OC - - 0.4 V I/OC = 0.5mA VTUVH 2.1 2.3 2.5 V VIN Increasing VTUVL 2.0 2.2 2.4 V VIN Decreasing AC Characteristics Parameter Symbol Limit Min Typ Max Unit Conditions Output Rise Time tON1 - 1 6 ms RL = 20Ω Output Turn ON Time tON2 - 1.5 10 ms RL = 20Ω Output Fall Time tOFF1 - 1 20 μs RL = 20Ω Output Turn OFF Time tOFF2 - 3 40 μs RL = 20Ω /OC Delay Time t/OC 10 15 20 ms www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 3/22 TSZ02201-0E3E0H300190-1-2 25.Jan.2021 Rev.004 BD2220G Datasheet BD2221G Electrical Characteristics – continued BD2221G (VIN= 5V, Ta= 25°C, unless otherwise specified.) DC Characteristics Limit Parameter Symbol Min Typ Max Unit Conditions Operating Current IDD - 110 160 μA Standby Current ISTB - 0.01 5 μA V/ENH 2.0 - - V V/EN = 0V VOUT = Open V/EN = 5V VOUT = Open High Input V/ENL - - 0.8 V Low Input /EN Input Leakage I/EN -1.0 +0.01 +1.0 μA V/EN = 0V or 5V ON-Resistance RON - 160 210 mΩ IOUT = 50mA Switch Leak Current ILSW - - 1.0 μA V/EN = 0V, VOUT = 0V Reverse Leak Current IREV - - 1.0 μA VOUT = 5.5V, VIN = 0V Over-Current Threshold ITH 0.5 - 1.0 A /EN Input Voltage Short Circuit Output Current /OC Output Low Voltage UVLO Threshold ISC 0.35 - - A VOUT = 0V, RMS V/OC - - 0.4 V I/OC = 0.5mA VTUVH 2.1 2.3 2.5 V VIN Increasing VTUVL 2.0 2.2 2.4 V VIN Decreasing AC Characteristics Parameter Symbol Limit Min Typ Max Unit Conditions Output Rise Time tON1 - 1 6 ms RL = 20Ω Output Turn ON Time tON2 - 1.5 10 ms RL = 20Ω Output Fall Time tOFF1 - 1 20 μs RL = 20Ω Output Turn OFF Time tOFF2 - 3 40 μs RL = 20Ω /OC Delay Time t/OC 10 15 20 ms www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 4/22 TSZ02201-0E3E0H300190-1-2 25.Jan.2021 Rev.004 BD2220G Datasheet BD2221G Measurement Circuit VIN VIN A A OUT VOUT IN VIN IN VIN RL GND GND VEN(/EN) VEN(/EN) /OC EN(/EN) A. VOUT OUT 1µF 1µF Operating Current B. EN(/EN) /OC EN,/EN Input Voltage, Output Rise / Fall Time VIN VIN A A 10kΩ IOC OUT VOUT IN VIN IN VIN 1µF 1µF IOUT GND VEN(/EN) C. OUT VOUT EN(/EN) GND VEN(/EN) /OC ON-Resistance, Over-Current Detection EN(/EN) D. /OC /OC Output Low Voltage Figure 1. Measurement Circuit Timing Diagram VEN EN VENL VENH V/EN TtON2 ON2 TtOFF2 OFF2 90% VOUT V/ENH V/ENL tON2 tOFF2 90% 90% 10% TtON1 ON1 10% VOUT TtOFF1 OFF1 www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 10% 10% tON1 Figure 2. Output Rise / Fall Time (BD2220G) 90% tOFF1 Figure 3. Output Rise / Fall Time (BD2221G) 5/22 TSZ02201-0E3E0H300190-1-2 25.Jan.2021 Rev.004 BD2220G Datasheet BD2221G Typical Performance Curves 140 140 VIN=5.0V Ta=25°C Operating Current : IDD[μA] Operating Current : IDD[μA] 120 100 80 60 40 120 100 80 60 40 20 20 0 0 2 3 4 5 -50 6 Supply Voltage ; VIN[V] Figure 4. Operating Current vs Supply Voltage (EN, /EN Enable) 50 100 Figure 5. Operating Current vs Ambient Temperature (EN, /EN Enable ) 1.0 1.0 Ta=25°C VIN=5.0V 0.8 Standby Current : ISTB[μA] Standby Current : ISTB[μA] 0 Ambient Temperature ; Ta[°C] 0.6 0.4 0.2 0.0 0.8 0.6 0.4 0.2 0.0 2 3 4 5 6 -50 Supply Voltage ; VIN[V] 50 100 Ambient Temperature ; Ta[°C] Figure 6. Standby Current vs Supply Voltage (EN, /EN Disable) www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 0 Figure 7. Standby Current vs Ambient Temperature (EN, /EN Disable) 6/22 TSZ02201-0E3E0H300190-1-2 25.Jan.2021 Rev.004 BD2220G Datasheet BD2221G Typical Performance Curves - continued 2.0 Ta=25°C 1.5 Enable Input Voltage : VEN, V/EN[V] Enable Input Voltage : VEN, V/EN[V] 2.0 Low to High High to Low 1.0 0.5 VIN=5.0V Low to High 1.5 High to Low 1.0 0.5 0.0 0.0 2 3 4 5 -50 6 0 Supply Voltage ; VIN[V] 100 Ambient Temperature ; Ta[°C] Figure 8. EN, /EN Input Voltage vs Supply Voltage Figure 9. EN, /EN Input Voltage vs Ambient Temperature 250 250 Ta=25°C VIN=5.0V 200 ON-Resistance : RON[mΩ ] ON-Resistance : RON[mΩ ] 50 150 100 50 200 150 100 50 0 0 2 3 4 5 -50 6 Supply Voltage ; VIN[V] 50 100 Ambient Temperature ; Ta[°C] Figure 10. ON-Resistance vs Supply Voltage www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 0 Figure 11. ON-Resistance vs Ambient Temperature 7/22 TSZ02201-0E3E0H300190-1-2 25.Jan.2021 Rev.004 BD2220G Datasheet BD2221G Typical Performance Curves - continued 1.0 1.0 Over-Current Threshold : ITH[A] Over-Current Threshold : ITH[A] Ta=25°C 0.9 0.8 0.7 0.6 0.9 0.8 0.7 0.6 0.5 0.5 2 3 4 5 -50 6 0 50 Supply Voltage ; VIN[V] Ambient Temperature ; Ta[°C] Figure 12. Over-Current Threshold vs Supply Voltage Figure 13. Over-Current Threshold vs Ambient Temperature 100 100 100 Ta=25°C /OC Output Low Voltage : V/OC[mV] /OC Output Low Voltage : V/OC[mV] VIN=5.0V 80 60 40 20 VIN=5.0V 80 60 40 20 0 0 -50 0 50 -50 100 Supply Voltage ; VIN[V] 50 100 Ambient Temperature ; Ta[°C] Figure 14. /OC Output Low Voltage vs Supply Voltage www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 0 Figure 15. /OC Output Low Voltage vs Ambient Temperature 8/22 TSZ02201-0E3E0H300190-1-2 25.Jan.2021 Rev.004 BD2220G Datasheet BD2221G Typical Performance Curves - continued 1.0 UVLO Hysteresis Voltage : VHYS[V] UVLO Threshold : VTUVH, VTUVL [V] 2.5 2.4 2.3 VTUVH 2.2 VTUVL 2.1 0.8 0.6 0.4 0.2 0.0 2.0 -50 0 50 -50 100 Ambient Temperature ; Ta[°C] 50 100 Ambient Temperature ; Ta[°C] Figure 16. UVLO Threshold Voltage vs Ambient Temperature Figure 17. UVLO Hysteresis Voltage vs Ambient Temperature 5.0 5.0 VIN=5.0V Ta=25°C 4.0 Output Rise Time : tON[ms] Output Rise Time : tON[ms] 0 3.0 2.0 1.0 4.0 3.0 2.0 1.0 0.0 0.0 2 3 4 5 -50 6 Supply Voltage ; VIN[V] 50 100 Ambient Temperature ; Ta[°C] Figure 18. Output Rise Time vs Supply Voltage www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 0 Figure 19. Output Rise Time vs Ambient Temperature 9/22 TSZ02201-0E3E0H300190-1-2 25.Jan.2021 Rev.004 BD2220G Datasheet BD2221G Typical Performance Curves - continued 5.0 Ta=25°C Output Turn ON Time : tON2[ms] Output Turn ON Time : tON2[ms] 5.0 4.0 3.0 2.0 1.0 VIN=5.0V 4.0 3.0 2.0 1.0 0.0 0.0 2 3 4 5 -50 6 0 Supply Voltage ; VIN[V] 100 Ambient Temperature ; Ta[°C] Figure 20. Output Turn ON Time vs Supply Voltage Figure 21. Output Turn ON Time vs Ambient Temperature 5.0 5.0 VIN=5.0V Ta=25°C 4.0 Output Fall Time : tOFF[µs] Output Fall Time : tOFF[µs] 50 3.0 2.0 1.0 4.0 3.0 2.0 1.0 0.0 0.0 2 3 4 5 -50 6 0 50 Supply Voltage ; VIN[V] Ambient Temperature ; Ta[°C] Figure 22. Output Fall Time vs Supply Voltage Figure 23. Output Fall Time vs Ambient Temperature www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 10/22 100 TSZ02201-0E3E0H300190-1-2 25.Jan.2021 Rev.004 BD2220G Datasheet BD2221G Typical Performance Curves - continued 6.0 Output tOFF2[µs] : TOFF2: [μs] TIMETime OFF OFF TURNTurn Output : t[μs] OFF2[µs] TURNTurn OFF OFF TIMETime : TOFF2 6.0 Ta=25°C 5.0 4.0 3.0 2.0 1.0 VIN=5.0V 5.0 4.0 3.0 2.0 1.0 0.0 0.0 2 3 4 5 SupplyVOLTAGE Voltage ; :VVININ[V] SUPPLY -50 6 Figure 24. Output Turn OFF Time vs Supply Voltage Figure 25. Output Turn OFF Time vs Ambient Temperature 20 20 VIN=5.0V /OC Delay Time : t/OC[ms] Ta=25°C /OC Delay Time : t/OC[ms] 0 50 100 AMBIENT TEMPERATURE Ta[℃] Ambient Temperature ; :Ta[°C] 18 16 14 12 18 16 14 12 10 10 2 3 4 5 -50 6 Supply Voltage ; VIN[V] 50 100 Ambient Temperature ; Ta[°C] Figure 26. /OC Delay Time vs Supply Voltage www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 0 Figure 27. /OC Delay Time vs Ambient Temperature 11/22 TSZ02201-0E3E0H300190-1-2 25.Jan.2021 Rev.004 BD2220G Datasheet BD2221G Typical Waveforms VEN (5V/div.) VEN (5V/div.) V/OC (5V/div.) V/OC (5V/div.) VOUT (5V/div.) VOUT (5V/div.) IOUT (0.5A/div.) IOUT (0.5A/div.) VIN=5V RL=20Ω VIN=5V RL=20Ω Time (1ms/div.) Time (2μs/div.) Figure 28. Output Rise Characteristic Figure 29. Output Fall Characteristic VEN (5V/div.) V/OC (5V/div.) V/OC (5V/div.) VOUT (5V/div.) CL=220μF CL =100μF IOUT (0.5A/div.) IOUT (0.2A/div.) CL =47μF VIN=5V 1A/10ms VIN=5V RL=20Ω Time (1ms/div.) Time (2ms/div.) Figure 30. Inrush Current Response Figure 31. Over-Current Response Ramped Load www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 12/22 TSZ02201-0E3E0H300190-1-2 25.Jan.2021 Rev.004 BD2220G Datasheet BD2221G Typical Waveforms - continued V/OC (5V/div.) VEN (5V/div.) VOUT (5V/div.) V/OC (5V/div.) VOUT (5V/div.) IOUT (0.5A/div.) IOUT (0.5A/div.) VIN=5V 1A/50ms VIN=5V Time (10ms/div.) Time (5ms/div.) Figure 32. Over-Current Response Ramped Load Figure 33. Over-Current Response Enable to Short-Circuit V/OC (5V/div.) VIN (5V/div.) VOUT (5V/div.) VOUT (5V/div.) IOUT (0.2A/div.) IOUT (1A/div.) RL=20Ω VIN=5V RL=1Ω Time (5ms/div.) Time (10ms/div.) Figure 34. Over-Current Response 1Ω Load Connected at EN Figure 35. UVLO Response Increasing VIN www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 13/22 TSZ02201-0E3E0H300190-1-2 25.Jan.2021 Rev.004 BD2220G Datasheet BD2221G Typical Wave Forms - continued VIN (5V/div.) VOUT (5V/div.) IOUT (0.2A/div.) RL=20Ω Time (10ms/div.) Figure 36. UVLO Response Decreasing VIN www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 14/22 TSZ02201-0E3E0H300190-1-2 25.Jan.2021 Rev.004 BD2220G Datasheet BD2221G Typical Application Circuit 10kΩ 10kΩ~ to 100kΩ 100kΩ CIN Controller 5V(Typ) 5V (Typ.) Ferrite Beads VIN IN VOUT OUT + GND CL - EN(/EN) /OC Application Information When excessive current flows due to output short circuit or so, ringing occurs because of inductance between power source line and IC. This may cause bad effects on IC operations. In order to avoid this case, connect a bypass capacitor across IN terminal and GND terminal of IC. 1μF or higher is recommended. Pull up /OC output by a resistance value of 10kΩ to 100kΩ. Set up value which satisfies the application of either CL. This application circuit does not guarantee its operation. When using the circuit with changes to the external circuit constants, make sure to leave an adequate margin for external components including AC/DC characteristics as well as dispersion of the IC. Functional Description 1. Switch Operation IN terminal and OUT terminal are connected to the drain and the source of switch MOSFET respectively. The IN terminal is also used as power source input to internal control circuit. When the switch is turned on from EN, /EN control input, the switch is bidirectional. IN terminal and OUT terminal are connected by a 160mΩ (Typ) switch. Therefore, when the potential of OUT terminal is higher than that of IN terminal, current flows from OUT terminal to IN terminal. On the other hand, when the switch is turned OFF, it is possible to prevent current from flowing reversely from OUT to IN since a parasitic diode between the drain and the source of switch MOSFET is not present, 2. Thermal Shutdown Circuit (TSD) If over-current would continue, the temperature of the IC would increase drastically. If the junction temperature were beyond 170°C (Typ) during the condition of over-current detection, thermal shutdown circuit operates and turns power switch off and outputs a fault flag (/OC). Then, when the junction temperature decreases lower than 150°C (Typ), power switch is turned on and fault flag (/OC) is cancelled. Unless the increase of the chip’s temperature is removed or the output of power switch is turned off, this operation repeats. Note: The thermal shutdown circuit operates when the switch is on (EN, /EN signal is active). 3. Over-Current Detection (OCD) The over-current detection circuit limits current (ISC) and outputs a fault flag (/OC) when current flowing in each MOSFET exceeds a specified value. There are three types of response against over-current. The over-current detection circuit works when the switch is on (EN, /EN signal is active). (1) When the switch is turned on while the output is in short circuit status When the switch is turned on while the output is in short circuit status, the switch goes into current limit status immediately. (2) When the output short circuits while the switch is on When the output short circuits or high-current load is connected while the switch is on, very large current flows until the over-current limit circuit reacts. When the current detection and limit circuit works, current limitation is carried out. (3) When the output current increases gradually When the output current increases gradually, current limitation does not work until the output current exceeds the over-current detection value. When it exceeds the detection value, current limitation is carried out. 4. Under Voltage Lockout (UVLO) UVLO circuit prevents the switch from turning on until the VIN exceeds 2.3V(Typ). If VIN drops below 2.2V(Typ) while the switch is still ON, then UVLO will shut off the power switch. UVLO has a hysteresis of 100mV(Typ). Note: Under voltage lockout circuit works when the switch is on (EN, /EN signal is active). www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 15/22 TSZ02201-0E3E0H300190-1-2 25.Jan.2021 Rev.004 BD2220G Datasheet BD2221G 5. Fault Flag (/OC) Output Fault flag output is an NMOS open drain output. At detection of over-current and/or thermal shutdown, the output level is low. Over-current detection has delay filter. This delay filter prevents current detection flags from being sent during instantaneous events such as inrush current at switch on or during hot plug.. If fault flag output is unused, /OC pin should be connected to open or ground line. t/OC t/OC Output Current ON OFF ON Switch Status FLAG Output VEN Figure 37. Over-Current Shutdown Operation (Reset at Toggle of EN (BD2220G) t/OC t/OC Output Current ON OFF ON Switch Status FLAG Output VTUVL VTUVH VIN VEN Figure 38. Over-Current Shutdown Operation (Reset at UVLO operation) (BD2220G) www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 16/22 TSZ02201-0E3E0H300190-1-2 25.Jan.2021 Rev.004 BD2220G Datasheet BD2221G Power Dissipation (SSOP5 package) [mW ] DISSIPATIO :NP: Pd PO W ERDissipation Power d[mW] 700 600 500 400 300 200 100 0 0 25 50 75 85 100 125 150 ℃ AMBIENT TEMPERATURE : Ta [ ] Ambient Temperature ; Ta[°C] 70mm x 70mm x 1.6mm Glass Epoxy Board Figure 39. Power Dissipation Curve (Pd-Ta Curve) I/O Equivalence Circuit Symbol Pin No. EN (/EN) 3 OUT 5 Equivalence circuit EN (/EN) OUT VOUT /OC /OC www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 4 17/22 TSZ02201-0E3E0H300190-1-2 25.Jan.2021 Rev.004 BD2220G Datasheet BD2221G Operational Notes 1. Reverse Connection of Power Supply Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when connecting the power supply, such as mounting an external diode between the power supply and the IC’s power supply pins. 2. Power Supply Lines Design the PCB layout pattern to provide low impedance supply lines. Separate the ground and supply lines of the digital and analog blocks to prevent noise in the ground and supply lines of the digital block from affecting the analog block. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and aging on the capacitance value when using electrolytic capacitors. 3. Ground Voltage Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition. 4. Ground Wiring Pattern When using both small-signal and large-current ground traces, the two ground traces should be routed separately but connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal ground caused by large currents. Also ensure that the ground traces of external components do not cause variations on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance. 5. Thermal Consideration Should by any chance the power dissipation rating be exceeded the rise in temperature of the chip may result in deterioration of the properties of the chip. The absolute maximum rating of the Pd stated in this specification is when the IC is mounted on a 70mm x 70mm x 1.6mm glass epoxy board. In case of exceeding this absolute maximum rating, increase the board size and copper area to prevent exceeding the Pd rating. 6. Recommended Operating Conditions These conditions represent a range within which the expected characteristics of the IC can be approximately obtained. The electrical characteristics are guaranteed under the conditions of each parameter. 7. In rush Current When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush current may flow instantaneously due to the internal powering sequence and delays, especially if the IC has more than one power supply. Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and routing of connections. 8. Operation Under Strong Electromagnetic Field Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction. 9. Testing on Application Boards When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may subject the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply should always be turned off completely before connecting or removing it from the test setup during the inspection process. To prevent damage from static discharge, ground the IC during assembly and use similar precautions during transport and storage. 10. Inter-pin Short and Mounting Errors Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin. Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and unintentional solder bridge deposited in between pins during assembly to name a few. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 18/22 TSZ02201-0E3E0H300190-1-2 25.Jan.2021 Rev.004 BD2220G Datasheet BD2221G Operational Notes - continued 11. Unused Input Pins Input pins of an IC are often connected to the gate of a MOS transistor. The gate has extremely high impedance and extremely low capacitance. If left unconnected, the electric field from the outside can easily charge it. The small charge acquired in this way is enough to produce a significant effect on the conduction through the transistor and cause unexpected operation of the IC. So unless otherwise specified, unused input pins should be connected to the power supply or ground line. 12. Regarding the Input Pin of the IC This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them isolated. P-N junctions are formed at the intersection of the P layers with the N layers of other elements, creating a parasitic diode or transistor. For example (refer to figure below): When GND > Pin A and GND > Pin B, the P-N junction operates as a parasitic diode. When GND > Pin B, the P-N junction operates as a parasitic transistor. Parasitic diodes inevitably occur in the structure of the IC. The operation of parasitic diodes can result in mutual interference among circuits, operational faults, or physical damage. Therefore, conditions that cause these diodes to operate, such as applying a voltage lower than the GND voltage to an input pin (and thus to the P substrate) should be avoided. Resistor Transistor (NPN) Pin A Pin B C E Pin A N P+ P N N P+ N Pin B B Parasitic Elements N P+ N P N P+ B N C E Parasitic Elements P Substrate P Substrate GND GND Parasitic Elements GND Parasitic Elements GND N Region close-by Figure 40. Example of monolithic IC structure 13. Ceramic Capacitor When using a ceramic capacitor, determine the dielectric constant considering the change of capacitance with temperature and the decrease in nominal capacitance due to DC bias and others. 14. Thermal Shutdown Circuit(TSD) This IC has a built-in thermal shutdown circuit that prevents heat damage to the IC. Normal operation should always be within the IC’s power dissipation rating. If however the rating is exceeded for a continued period, the junction temperature (Tj) will rise which will activate the TSD circuit that will turn OFF all output pins. When the Tj falls below the TSD threshold, the circuits are automatically restored to normal operation. Note that the TSD circuit operates in a situation that exceeds the absolute maximum ratings and therefore, under no circumstances, should the TSD circuit be used in a set design or for any purpose other than protecting the IC from heat damage. 15. Thermal design Perform thermal design in which there are adequate margins by taking into account the power dissipation (Pd) in actual states of use. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 19/22 TSZ02201-0E3E0H300190-1-2 25.Jan.2021 Rev.004 BD2220G Datasheet BD2221G Ordering Information B D 2 2 2 0 Part Number B D G - Package G: SSOP5 2 2 2 1 Part Number G TR Packaging and forming specification TR: Embossed tape and reel - Package G: SSOP5 TR Packaging and forming specification TR: Embossed tape and reel Marking Diagram SSOP5 (TOP VIEW) Part Number Marking LOT Number Part Number Part Number Marking BD2220G DX BD2221G DY www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 20/22 TSZ02201-0E3E0H300190-1-2 25.Jan.2021 Rev.004 BD2220G Datasheet BD2221G Physical Dimension, Tape and Reel Information Package Name www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 SSOP5 21/22 TSZ02201-0E3E0H300190-1-2 25.Jan.2021 Rev.004 BD2220G Datasheet BD2221G Revision History Date Revision Changes 11.Mar.2013 001 New Release 25.Jun.2013 002 Modified Y-axis of figure 4. Changed character color from RED to BLOCK of figure 16. 21.Aug.2014 003 Applied the ROHM Standard Style and improved understandability. 25.Jan.2021 004 P.22-2, P22-3 Updated packages and part numbers. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 22/22 TSZ02201-0E3E0H300190-1-2 25.Jan.2021 Rev.004 BD2220G Datasheet BD2221G Ordering Information B D 2 2 2 0 Part Number G - Package G: SSOP5A ZTR Production site Z: Added Packaging and forming specification TR: Embossed tape and reel B D 2 2 2 1 Part Number G - Package G: SSOP5A ZTR Production site Z: Added Packaging and forming specification TR: Embossed tape and reel Marking Diagram SSOP5A (TOP VIEW) Part Number Marking LOT Number Part Number Part Number Marking BD2220G DX BD2221G DY www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 22-2/22 TSZ02201-0E3E0H300190-1-2 25.Jan.2021 Rev.004 BD2220G Datasheet BD2221G Physical Dimension and Packing Information Package Name www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 SSOP5A 22-3/22 TSZ02201-0E3E0H300190-1-2 25.Jan.2021 Rev.004 Notice Precaution on using ROHM Products 1. Our Products are designed and manufactured for application in ordinary electronic equipment (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), transport equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅢ CLASSⅣ CLASSⅢ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (Exclude cases where no-clean type fluxes is used. However, recommend sufficiently about the residue.) ; or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse, is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in the range that does not exceed the maximum junction temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice-PGA-E © 2015 ROHM Co., Ltd. All rights reserved. Rev.004 Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl 2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign trade act, please consult with ROHM in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the Products with other articles such as components, circuits, systems or external equipment (including software). 3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the Products, subject to the terms and conditions herein. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice-PGA-E © 2015 ROHM Co., Ltd. All rights reserved. Rev.004 Datasheet General Precaution 1. Before you use our Products, you are requested to carefully read this document and fully understand its contents. ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of any ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this document is current as of the issuing date and subject to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sales representative. 3. The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccuracy or errors of or concerning such information. Notice – WE © 2015 ROHM Co., Ltd. All rights reserved. Rev.001