Datasheet
1 Channel Compact High Side Switch ICs
0.76A Current Limit High Side Switch ICs
BD22641G-M
General Description
Key Specifications
Input Voltage Range:
ON-Resistance:
Over-Current Threshold:
Standby Current:
Operating Temperature Range:
BD22641G-M is a low on-resistance N-channel
MOSFET high-side power switch, optimized for
Universal Serial Bus (USB) applications. BD22641G-M
is equipped with the function of over-current detection,
thermal shutdown, under-voltage lockout and soft-start.
Features
Package
(Note1)
W(Typ) x D(Typ) x H(Max)
AEC-Q100 Qualified
Over Current Threshold: 0.76A
Built-in Low ON-Resistance (Typ 120mΩ)
N-Channel MOSFET
Reverse Current Protection when
Power Switch Off
Thermal Shutdown
Under-Voltage Lockout
Open-Drain Error Flag Output
Output Discharge Function
Soft Start Circuit
Control Input Logic : Active-High
2.7V to 5.5V
120mΩ(Typ)
0.76A(Typ)
0.01μA (Typ)
-40°C to +105°C
SSOP5
2.90mm x 2.80mm x 1.25mm
(Note1: Grade2)
Applications
Car accessory, Industrial applications
Typical Application Circuit
5V (Typ)
3.3V
IN
CIN
OUT
+
GND
10kΩ to
100kΩ
CL
-
EN
/OC
Lineup
Min
Over-Current Threshold
Typ
Max
0.57A
0.76A
0.96A
○Product structure:Silicon monolithic integrated circuit
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・14・001
Control Input
Logic
High
Package
SSOP5
Orderable Part Number
Reel of 3000
BD22641G-MTR
○This product has not designed protection against radioactive rays
1/23
TSZ02201-0GCG0H300050-1-2
2.Nov.2016 Rev.001
BD22641G-M
Block Diagram
OUT
IN
EN
Pin Configurations
TOP VIEW
1
OUT 5
IN
2 GND
/OC 4
3 EN
Pin Description
Pin No.
Symbol
I/O
Function
1
IN
-
Switch input and supply voltage for the IC.
2
GND
-
Ground.
3
EN
I
Enable input.
EN: High level input turns on the switch.
4
/OC
O
Over-current detection pin.
Low level output during over-current or over-temperature condition.
Open-drain fault flag output.
5
OUT
O
Switch output.
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
www.rohm.com
2/23
TSZ02201-0GCG0H300050-1-2
2.Nov.2016 Rev.001
BD22641G-M
Absolute Maximum Ratings
Parameter
Symbol
Rating
Unit
IN Supply Voltage
VIN
-0.3 to +6.0
V
EN Input Voltage
VEN
-0.3 to +6.0
V
/OC Voltage
V/OC
-0.3 to +6.0
V
/OC Sink Current
I/OC
5
mA
OUT Voltage
VOUT
-0.3 to +6.0
V
Storage Temperature
Tstg
-55 to +150
°C
Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit
between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated over
the absolute maximum ratings.
Thermal Resistance(Note1)
Parameter
Symbol
Thermal Resistance (Typ)
1s
(Note3)
(Note4)
2s2p
Unit
SSOP5
Junction to Ambient
Junction to Top Characterization Parameter
(Note2)
θJA
376.5
185.4
°C/W
ΨJT
40
30
°C/W
(Note1)Based on JESD51-2A(Still-Air)
(Note2)The thermal characterization parameter to report the difference between junction temperature and the temperature at the top center of the outside
surface of the component package.
(Note3)Using a PCB board based on JESD51-3.
Layer Number of
Measurement Board
Single
Material
Board Size
FR-4
114.3mm x 76.2mm x 1.57mmt
Top
Copper Pattern
Thickness
Footprints and Traces
70μm
(Note4)Using a PCB board based on JESD51-7.
Layer Number of
Measurement Board
4 Layers
Material
Board Size
FR-4
114.3mm x 76.2mm x 1.6mmt
Top
Copper Pattern
Footprints and Traces
2 Internal Layers
Thickness
70μm
Copper Pattern
2
74.2mm (Square)
Bottom
Thickness
Copper Pattern
Thickness
35μm
2
70μm
74.2mm (Square)
Recommended Operating Conditions (Tj= -40°C to +105°C)
Parameter
IN Operating Voltage
Continuous Current
Symbol
Unit
Min
Typ
Max
VIN
2.7
5.0
5.5
V
IOMAX
-
-
500
mA
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
www.rohm.com
Rating
3/23
TSZ02201-0GCG0H300050-1-2
2.Nov.2016 Rev.001
BD22641G-M
Electrical Characteristics
(VIN= 5V, Tj= -40 to +105°C, unless otherwise specified.)
DC Characteristics
Parameter
Symbol
Limit
Min
Typ
Max
Unit
Conditions
Operating Current
IDD
-
110
200
μA
Standby Current
ISTB
-
0.01
5
μA
VENH
2.0
-
-
V
VEN = 5V
VOUT = open
VEN = 0V
VOUT = open
High Input, VIN=3.3 to 5V
VENL
-
-
0.8
V
Low Input, VIN=5V
VENL
-
-
0.6
V
Low Input, VIN=3.3V
IEN
-1
+0.01
+1
μA
-
120
165
-
120
250
-
140
190
-
140
270
-
-
1.0
VEN = 0V or 5V
VIN=5V, IOUT = 500mA
Tj= 25°C
VIN=5V, IOUT = 500mA
Tj= -40°C to +105°C
VIN=3.3V, IOUT = 500mA
Tj= 25°C
VIN=3.3V, IOUT = 500mA
Tj= -40°C to +105°C
VOUT = 5.0V, VIN = 0V
570
765
960
EN Input Voltage
EN Input Leakage
ON-Resistance
RON
mΩ
μA
Reverse Leak Current
IREV
Over-Current Threshold
ITH
550
740
930
Short Circuit Output Current
ISC
320
500
680
mA
RDISC
15
60
165
Ω
IDISC = 1mA
Output Discharge Resistance
/OC Output Low Voltage
UVLO Threshold
mA
VIN = 5V
VIN = 3.3V
VIN=3.3 to 5V, VOUT = 0V, RMS
V/OC
-
-
0.4
V
I/OC = 0.5mA
VTUVH
2.1
2.3
2.5
V
VIN Increasing
VTUVL
2.0
2.2
2.4
V
VIN Decreasing
AC Characteristics
Parameter
Symbol
Limit
Min
Typ
Max
Unit
Output Rise Time
tON1
-
1
6
ms
Output Turn ON Time
tON2
-
1.5
10
ms
Output Fall Time
tOFF1
-
1
20
μs
Output Turn OFF Time
tOFF2
-
3
40
μs
/OC Delay Time
t/OC
9
15
21
ms
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
www.rohm.com
4/23
Conditions
RL = 20Ω
TSZ02201-0GCG0H300050-1-2
2.Nov.2016 Rev.001
BD22641G-M
Measurement Circuit
V IN
V IN
A
A
IN
OUT
IN
1µF
GND
RL
GND
VEN
VEN
/O C
EN
A.
OUT
1µF
EN
Operating Current, Standby Current
B.
/O C
EN Input Voltage, Output Rise / Fall Time
V IN
V IN
A
A
10kΩ
I /O C
IN
OUT
IN
1µF
1µF
IO U T
GND
VEN
C.
OUT
GND
VEN
/O C
EN
EN
ON-Resistance, Over-Current Detection
D.
/O C
/OC Output Low Voltage
Figure 1. Measurement Circuit
Timing Diagram
VEN
VENL
VENH
tON2
tOFF2
90%
VOUT
90%
10%
10%
tON1
tOFF1
Figure 2. Output Rise / Fall Time
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
www.rohm.com
5/23
TSZ02201-0GCG0H300050-1-2
2.Nov.2016 Rev.001
BD22641G-M
160
160
140
140
120
Ta=105°C
Operating Current : IDD[μA]
Operating Current : IDD[μA]
Typical Performance Curves
Ta=25°C
100
80
60
Ta=-40°C
40
20
VIN=5.5V
120
100
VIN=5V
80
60
VIN=2.7V
40
20
0
0
2
3
4
5
6
-50
-25
Supply Voltage : VIN[V]
0.40
0.40
0.35
0.35
0.30
0.30
Standby Current : ISTB[μA]
Standby Current : ISTB[μA]
125
Figure 4. Operating Current vs Ambient
Temperature
(EN Enable)
Figure 3. Operating Current vs Supply Voltage
(EN Enable)
0.25
0.20
0.15
Ta=105°C
0.10
0
25
50
75
100
Ambient Temperature: Ta[°C]
0.05
0.25
0.20
VIN=2.7V
VIN=5V
0.15
VIN=5.5V
0.10
0.05
Ta=85°C
0.00
0.00
2
3
4
5
Supply Voltage : VIN[V]
6
-50
www.rohm.com
0
25
50
75
100
Ambient Temperature : Ta[°C]
125
Figure 6. Standby Current vs Ambient Temperature
(EN Disable)
Figure 5. Standby Current vs Supply Voltage
(EN Disable)
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
-25
6/23
TSZ02201-0GCG0H300050-1-2
2.Nov.2016 Rev.001
BD22641G-M
3.0
3.0
2.5
2.5
Enable Input Voltage : VEN[V]
Enable Input Voltage : VEN[V]
Typical Performance Curves
2.0
Low to High
1.5
High to Low
1.0
0.5
2.0
Low to High
1.5
High to Low
1.0
0.5
Ta=25°C
VIN=5V
0.0
0.0
2
3
4
5
Supply Voltage : VIN[V]
6
-50
Figure 7. EN Input Voltage vs Supply
Voltage
(VENH, VENL)
-25
0
25
50
75
100
Ambient Temperature : Ta[°C]
125
Figure 8. EN Input Voltage vs Ambient
Temperature
(VENH, VENL)
250
250
VIN=2.7V
200
Ta=105°C
150
ON-Resistance : RON[mΩ]
ON-Resistance : RON[mΩ]
200
Ta=25°C
100
Ta=-40°C
50
VIN=5V
150
VIN=5.5V
100
50
0
0
2
3
4
5
Supply Voltage : VIN[V]
6
Figure 9 ON-Resistance vs Supply Voltage
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
www.rohm.com
-50
-25
0
25
50
75
100
Ambient Temperature : Ta[°C]
125
Figure 10.ON-Resistance vs Ambient Temperature
7/23
TSZ02201-0GCG0H300050-1-2
2.Nov.2016 Rev.001
BD22641G-M
Typical Performance Curves - continued
1.0
0.9
Over Current Threshold: ITH[A]
Over Current Threshold: ITH[A]
1.0
Ta=105°C
Ta=25°C
0.8
0.7
Ta=-40°C
0.6
0.5
0.9
VIN=5V
VIN=5.5V
0.8
0.7
VIN=2.7V
0.6
0.5
0.4
0.4
2
3
4
5
Supply Voltage: VIN[V]
6
-50
0
25
50
75
100
Ambient Temperature: Ta[°C]
125
Figure 12. Over-Current Threshold vs
Ambient Temperature
Figure 11. Over-Current Threshold vs
Supply Voltage
200
Output Discharge Resistance: RDISC [Ω]
200
Output Discharge Resistance: RDISC [Ω]
-25
Ta=105°C
150
Ta=25°C
100
Ta=-40°C
50
0
150
VIN=2.7V
100
VIN=5V
50
VIN=5.5V
0
2
3
4
5
Supply Voltage: VIN[V]
6
Figure 13. Output Discharge Resistance vs
Supply Voltage
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
www.rohm.com
-50
-25
0
25
50
75
100
Ambient Temperature: Ta[°C]
125
Figure 14. Output Discharge Resistance vs
Ambient Temperature
8/23
TSZ02201-0GCG0H300050-1-2
2.Nov.2016 Rev.001
BD22641G-M
Typical Performance Curves - continued
100
/OC Output Low Voltage: V/OC[mV]
/OC Output Low Voltage: V/OC[mV]
100
Ta=105°C
80
Ta=25°C
60
40
Ta=-40°C
20
0
80
VIN=2.7V
60
VIN=5V
40
VIN=5.5V
20
0
2
3
4
5
Supply Voltage : VIN[V]
6
-50
Figure 15. /OC Output Low Voltage vs
Supply Voltage
0
25
50
75
100
Ambient Temperature : Ta[°C]
125
Figure 16. /OC Output Low Voltage vs
Ambient Temperature
2.5
0.4
UVLO Hysteresis Voltage: VHYS[V]
UVLO Threshold: VTUVH, VTUVL[V]
-25
2.4
2.3
VTUVH
2.2
VTUVL
2.1
2.0
0.3
0.2
0.1
0.0
-50
-25
0
25
50
75
100
125
Ambient Temperature: Ta[°C]
Figure 17. UVLO Threshold Voltage vs
Ambient Temperature
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
www.rohm.com
-50
-25
0
25
50
75
100
Ambient Temperature: Ta[°C]
125
Figure 18. UVLO Hysteresis Voltage vs
Ambient Temperature
9/23
TSZ02201-0GCG0H300050-1-2
2.Nov.2016 Rev.001
BD22641G-M
5.0
5.0
4.0
4.0
Rise Time: TON1[ms]
Rise Time: TON1[ms]
Typical Performance Curves - continued
3.0
Ta=-40°C
Ta=25°C
2.0
3.0
2.0
VIN=5.5V
VIN=5V
1.0
1.0
VIN=2.7V
V
Ta=105°C
0.0
0.0
2
3
4
5
Supply Voltage: VIN[V]
-50
6
-25
5.0
4.0
4.0
Turn On Time: TON2[ms]
Turn On Time: TON2[ms]
50
75
100
125
Figure 20. Output Rise Time vs
Ambient Temperature
5.0
Ta=-40°C
Ta=25°C
2.0
1.0
25
Ambient Temperature: Ta[°C]
Figure 19. Output Rise Time vs
Supply Voltage
3.0
0
VIN=5.5V
3.0
VIN=5V
2.0
1.0
Ta=105°C
0.0
VIN=2.7V
0.0
2
3
4
5
Supply Voltage: VIN[V]
6
www.rohm.com
-25
0
25
50
75
100
125
Ambient Temperature: Ta[°C]
Figure 21. Output Turn-On Time vs
Supply Voltage
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
-50
Figure 22. Output Turn-On Time vs
Ambient Temperature
10/23
TSZ02201-0GCG0H300050-1-2
2.Nov.2016 Rev.001
BD22641G-M
5.0
5.0
4.0
4.0
Fall Time: TOFF1[µs]
Fall Time: TOFF1[µs]
Typical Performance Curves - continued
3.0
Ta=-40°C
2.0
Ta=25°C
1.0
3.0
VIN=2.7V
VIN=5.5V
2.0
VIN=5V
1.0
Ta=105°C
0.0
0.0
2
3
4
5
Supply Voltage: VIN[V]
6
-50
-25
125
Figure 24. Output Fall Time vs
Ambient Temperature
Figure 23. Output Fall Time vs Supply
Voltage
6.0
6.0
VIN=5.5V
Ta=-40°C
5.0
5.0
VIN=5V
Turn Off Time: TOFF2[µs]
Ta=25°C
Turn Off Time: TOFF2[µs]
0
25
50
75
100
Ambient Temperature: Ta[°C]
4.0
3.0
Ta=105°C
2.0
1.0
4.0
3.0
VIN=2.7V
2.0
1.0
0.0
0.0
2
3
4
5
Supply Voltage: VIN[V]
6
www.rohm.com
-25
0
25
50
75
100
Ambient Temperature: Ta[°C]
125
Figure 26. Output Turn-Off Time vs
Ambient Temperature
Figure 25. Output Turn-Off Time vs
Supply Voltage
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
-50
11/23
TSZ02201-0GCG0H300050-1-2
2.Nov.2016 Rev.001
BD22641G-M
Typical Performance Curves - continued
20
20
/OC Delay Time: t/OC[ms]
/OC Delay Time: t/OC[ms]
18
Ta=-40°C
18
Ta=105°C
16
Ta=25°C
14
12
VIN=2.7V
16
VIN=5V
14
VIN=5.5V
12
10
10
2
3
4
5
Supply Voltage: VIN[V]
6
-50
www.rohm.com
0
25
50
75
100
Ambient Temperature: Ta[°C]
125
Figure 28. /OC Delay Time vs Ambient
Temperature
Figure 27. /OC Delay Time vs
Supply Voltage
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
-25
12/23
TSZ02201-0GCG0H300050-1-2
2.Nov.2016 Rev.001
BD22641G-M
Typical Wave Forms
(Ta=25°C, unless otherwise specified)
VEN
(5V/div.)
VEN
(5V/div.)
V/OC
(5V/div.)
V/OC
(5V/div.)
VOUT
(5V/div.)
VOUT
(5V/div.)
IOUT
(0.5A/div.)
IOUT
(0.5A/div.)
VIN=5V
RL=20Ω
VIN=5V
RL=20Ω
TIME(1ms/div.)
TIME(1μs/div.)
Figure 29. Output Rise Characteristic
Figure 30. Output Fall Characteristic
VEN
(5V/div.)
V/OC
(5V/div.)
V/OC
(5V/div.)
VOUT
(5V/div.)
CL=220μF
CL=100μF
IOUT
(0.5A/div.)
IOUT
(0.2A/div.)
CL=47μF
VIN=5V
TIME (1ms/div.)
TIME (5ms/div.)
Figure 31. Inrush Current Response
Figure 32. Over-Current Response
Ramped Load
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
www.rohm.com
VIN=5V
RL=20Ω
13/23
TSZ02201-0GCG0H300050-1-2
2.Nov.2016 Rev.001
BD22641G-M
Typical Wave Forms – continued
(Ta=25°C, unless otherwise specified)
VEN
(5V/div.)
VEN
(5V/div.)
V/OC
(5V/div.)
VOUT
(5V/div.)
VOUT
(5V/div.)
V/OC
(5V/div.)
IOUT
(0.5A/div.)
VIN=5V
IOUT
(0.5A/div.)
VIN=5V
VIN=5V
TIME (5ms/div.)
TIME (100ms/div.)
Figure 33. Over-Current Response
Enable to Short Circuit
Figure 34. Over-Current Response
Enable to Short Circuit
VOUT
(5V/div.)
VIN
(5V/div.)
V/OC
(5V/div.)
VOUT
(5V/div.)
IOUT
(0.2A/div.)
IOUT
(1A/div.)
RL=20Ω
VIN=5V
TIME (5ms/div.)
TIME (10ms/div.)
Figure 35. Over-Current Response
1Ω Load Connected to VOUT
Figure 36. UVLO Response when
Increasing VIN
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
www.rohm.com
14/23
TSZ02201-0GCG0H300050-1-2
2.Nov.2016 Rev.001
BD22641G-M
Typical Wave Forms – continued
(Ta=25°C, unless otherwise specified)
VIN
(5V/div.)
VOUT
(5V/div.)
IOUT
(0.2A/div.)
RL=20Ω
TIME (10ms/div.)
Figure 37. UVLO Response when
Decreasing VIN
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
www.rohm.com
15/23
TSZ02201-0GCG0H300050-1-2
2.Nov.2016 Rev.001
BD22641G-M
Typical Application Circuit
5 V (Typ )
1 0 k Ω to
100kΩ
C IN
IN
OUT
+
C o n tro lle r
GND
CL
-
EN
/O C
Application Information
When excessive current flows due to output short-circuit, ringing occurs because of the inductance between power source
line and the IC. IN pin functions as both the power supply of the internal circuit of the IC and input of power switch. Therefore,
ringing of power line may cause adverse effects on IC operations. In order to avoid this, it is recommended to connect a low
ESR bypass capacitor (1μF or higher) between IN and GND pin which should be placed as close to these pins as possible.
Additionally, in order to decrease voltage fluctuations from power source line to IC, connect a low ESR capacitor in parallel
with CIN. 10μF to 100μF or higher is effective.
Pull up /OC output using 10kΩ to 100kΩ resistor values.
The value of CL should be chosen to satisfy the intended application.
This system connection diagram does not guarantee operation as the intended application.
When using the circuit with changes to the external circuit values, make sure to leave an adequate margin for external
components taking into consideration the DC and transient characteristics as well as the design tolerance of the IC.
Functional Description
1. Switch Operation
IN pin and OUT pin are connected to the drain and the source of switch MOSFET respectively. The IN pin is also used as
power source input to internal control circuit.
When the switch is turned ON from EN control input, the IN and OUT pins are connected by a 120mΩ (Typ) switch. In ON
status, the switch is bidirectional. Therefore, when the potential of OUT pin is higher than that of IN pin, current flows from
OUT to IN pin. On the other hand, when the switch is turned off, it is possible to prevent current from flowing reversely
from OUT to IN pin since a parasitic diode between the drain and the source of switch MOSFET is not present.
2. Thermal Shutdown Circuit (TSD)
In the event of continuous over-current condition, the temperature of the IC would increase drastically. If the junction
temperature goes beyond 165°C (Typ) due to over-current detection, thermal shutdown circuit operates and turns power
switch off, and the IC outputs a fault flag (/OC). Then, when the junction temperature decreases lower than 145°C (Typ),
the power switch is turned on and fault flag (/OC) is cancelled. This operation repeats, unless the cause of the increase of
chip’s temperature is removed or the output of power switch is turned OFF.
The thermal shutdown circuit operates when the switch is ON (EN signal is active).
3. Over-Current Detection (OCD)
The over-current detection circuit limits current (ISC) and outputs fault flag (/OC) when current flowing in each switch
MOSFET exceeds a specified value. The over-current detection circuit works when the switch is on (EN signal is active).
There are three types of response against over-current:
(1) When the switch is turned on while the output is in short circuit status, the switch goes into current limit status
immediately.
(2) When the output short-circuits or high capacity load is connected while the switch is on, very large current
flows until the over-current limit circuit reacts. When the current detection and limit circuit operates, current
limitation is carried out.
(3) When the output current increases gradually, current limitation would not operate unless the output current
exceeds the over-current detection value. When it exceeds the detection value, current limitation is carried out.
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
www.rohm.com
16/23
TSZ02201-0GCG0H300050-1-2
2.Nov.2016 Rev.001
BD22641G-M
4. Under-Voltage Lockout (UVLO)
UVLO circuit prevents the switch from turning on until the VIN exceeds 2.3V (Typ). If VIN drops below 2.2V (Typ) while the
switch is still ON, then UVLO shuts off the power switch. UVLO has a hysteresis of 100mV (Typ).
Under-voltage lockout circuit operates when the switch is on (EN signal is active).
5. Fault Flag (/OC) Output
Fault flag output is an N-MOS open drain output. During detection of over-current and/or thermal shutdown, the output
level will turn low.
Over-current detection has delay filter. This delay filter prevents current detection flags from being sent during
instantaneous events such as inrush current at switch on or during hot plug. If fault flag output is unused, /OC pin should
be connected to open or ground line.
6. Output Discharge Function
When the switch is turned off by disabling control input or UVLO function, the 60Ω(Typ.) discharge circuit between OUT
and GND turns on which discharges the electric charge of the capacitive load. However, if the voltage of IN declines
rapidly, then the OUT pin becomes Hi-Z without UVLO function.
Over-Current
Detection
Over-Current
Load Removed
VOUT
ITH
ISC
IOUT
t/OC
V/OC
Figure 38. Over-Current Detection
VEN
Output Short Circuit
VOUT
Thermal Shutdown
IOUT
V/OC
/OC Delay Time
Figure 39. Over-Current Detection, Thermal Shutdown Timing
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
www.rohm.com
17/23
TSZ02201-0GCG0H300050-1-2
2.Nov.2016 Rev.001
BD22641G-M
I/O Equivalent Circuit
Symbol
Pin No.
EN
3
OUT
5
Equivalent Circuit
EN
OUT
/O C
/OC
4
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
www.rohm.com
18/23
TSZ02201-0GCG0H300050-1-2
2.Nov.2016 Rev.001
BD22641G-M
Operational Notes
1.
Reverse Connection of Power Supply
Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when
connecting the power supply, such as mounting an external diode between the power supply and the IC’s power
supply pins.
2.
Power Supply Lines
Design the PCB layout pattern to provide low impedance supply lines. Furthermore, connect a capacitor to ground at
all power supply pins. Consider the effect of temperature and aging on the capacitance value when using electrolytic
capacitors
3.
Ground Voltage
Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition.
4.
Ground Wiring Pattern
When using both small-signal and large-current ground traces, the two ground traces should be routed separately but
connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal
ground caused by large currents. Also ensure that the ground traces of external components do not cause variations
on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance.
5.
Thermal Consideration
The amount of heat generated depends on the On-state resistance and Output current.
Should by any condition the maximum junction temperature Tjmax = 150 °C rating be exceeded by the temperature
increase of the chip, it may result in deterioration of the properties of the chip. The thermal impedance in this
specification is based on recommended PCB and measurement condition by JEDEC standard. Verify the application
and allow sufficient margins in the thermal design.
6.
Recommended Operating Conditions
These conditions represent a range within which the expected characteristics of the IC can be approximately obtained.
The electrical characteristics are guaranteed under the conditions of each parameter.
7.
Inrush Current
When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush current may flow
instantaneously due to the internal powering sequence and delays, especially if the IC has more than one power
supply. Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and
routing of connections.
8.
Operation Under Strong Electromagnetic Field
Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction.
9.
Testing on Application Boards
When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may
subject the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply
should always be turned off completely before connecting or removing it from the test setup during the inspection
process. To prevent damage from static discharge, ground the IC during assembly and use similar precautions during
transport and storage.
10. Inter-pin Short and Mounting Errors
Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in
damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin.
Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and
unintentional solder bridge deposited in between pins during assembly to name a few.
11. Unused Input Pins
Input pins of an IC are often connected to the gate of a MOS transistor. The gate has extremely high impedance and
extremely low capacitance. If left unconnected, the electric field from the outside can easily charge it. The small
charge acquired in this way is enough to produce a significant effect on the conduction through the transistor and
cause unexpected operation of the IC. So unless otherwise specified, unused input pins should be connected to the
power supply or ground line.
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
www.rohm.com
19/23
TSZ02201-0GCG0H300050-1-2
2.Nov.2016 Rev.001
BD22641G-M
Operational Notes – continued
12. Regarding the Input Pin of the IC
This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them
isolated. P-N junctions are formed at the intersection of the P layers with the N layers of other elements, creating a
parasitic diode or transistor. For example (refer to figure below):
When GND > Pin A and GND > Pin B, the P-N junction operates as a parasitic diode.
When GND > Pin B, the P-N junction operates as a parasitic transistor.
Parasitic diodes inevitably occur in the structure of the IC. The operation of parasitic diodes can result in mutual
interference among circuits, operational faults, or physical damage. Therefore, conditions that cause these diodes to
operate, such as applying a voltage lower than the GND voltage to an input pin (and thus to the P substrate) should be
avoided.
Resistor
Transistor (NPN)
Pin A
Pin B
C
E
Pin A
N
P+
P
N
N
P+
N
Pin B
B
Parasitic
Elements
N
P+
N P
N
P+
B
N
C
E
Parasitic
Elements
P Substrate
P Substrate
GND
GND
Parasitic
Elements
GND
Parasitic
Elements
GND
N Region
close-by
Figure 40. Example of monolithic IC structure
13. Ceramic Capacitor
When using a ceramic capacitor, determine the dielectric constant considering the change of capacitance with
temperature and the decrease in nominal capacitance due to DC bias and others.
14. Thermal Shutdown Circuit(TSD)
This IC has a built-in thermal shutdown circuit that prevents heat damage to the IC. Normal operation should always
be within the IC’s maximum junction temperature rating. If however the rating is exceeded for a continued period, the
junction temperature (Tj) will rise which will activate the TSD circuit that will turn OFF all output pins. When the Tj falls
below the TSD threshold, the circuits are automatically restored to normal operation.
Note that the TSD circuit operates in a situation that exceeds the absolute maximum ratings and therefore, under no
circumstances, should the TSD circuit be used in a set design or for any purpose other than protecting the IC from
heat damage.
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
www.rohm.com
20/23
TSZ02201-0GCG0H300050-1-2
2.Nov.2016 Rev.001
BD22641G-M
Ordering Information
B
D
2
2
6
4
Part Number
BD22641G
1
G
-
Package
G: SSOP5
M
T R
Product Rank
M: for Automotive
Packaging and forming specification
TR: Embossed tape and reel
Marking Diagram
SSOP5 (TOP VIEW)
Part Number Marking
LOT Number
Part Number
Part Number Marking
BD22641G-M
XU
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
www.rohm.com
21/23
TSZ02201-0GCG0H300050-1-2
2.Nov.2016 Rev.001
BD22641G-M
Physical Dimension, Tape and Reel Information
Package Name
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
www.rohm.com
SSOP5
22/23
TSZ02201-0GCG0H300050-1-2
2.Nov.2016 Rev.001
BD22641G-M
Revision History
Date
Revision
2.Nov.2016
001
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
www.rohm.com
Changes
New Release
23/23
TSZ02201-0GCG0H300050-1-2
2.Nov.2016 Rev.001
Notice
Precaution on using ROHM Products
1.
(Note 1)
If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment
,
aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,
bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales
representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any
ROHM’s Products for Specific Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU
CHINA
CLASSⅢ
CLASSⅡb
CLASSⅢ
CLASSⅢ
CLASSⅣ
CLASSⅢ
2.
ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3.
Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below.
Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the
use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our
Products under any special or extraordinary environments or conditions (as exemplified below), your independent
verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4.
The Products are not subject to radiation-proof design.
5.
Please verify and confirm characteristics of the final or mounted products in using the Products.
6.
In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7.
De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in
the range that does not exceed the maximum junction temperature.
8.
Confirm that operation temperature is within the specified range described in the product specification.
9.
ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1.
When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2.
In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice-PAA-E
© 2015 ROHM Co., Ltd. All rights reserved.
Rev.003
Precautions Regarding Application Examples and External Circuits
1.
If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2.
You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1.
Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2.
Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3.
Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4.
Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign
trade act, please consult with ROHM in case of export.
Precaution Regarding Intellectual Property Rights
1.
All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data.
2.
ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the
Products with other articles such as components, circuits, systems or external equipment (including software).
3.
No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM
will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to
manufacture or sell products containing the Products, subject to the terms and conditions herein.
Other Precaution
1.
This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2.
The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3.
In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4.
The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice-PAA-E
© 2015 ROHM Co., Ltd. All rights reserved.
Rev.003
Datasheet
General Precaution
1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.
ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s
representative.
3.
The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or
liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or
concerning such information.
Notice – WE
© 2015 ROHM Co., Ltd. All rights reserved.
Rev.001