BD37034FV-ME2

Datasheet Sound Processors for Car Audios General-Purpose Electronic Volume with Built-in Advanced Switch BD37034FV-M General Description BD37034FV-M is sound processors for car audio. The functions are stereo 5 input selector, volume, 3-band equalizer, loudness, 6ch fader, mixing, HPF for front and rear, LPF for subwoofer, anti-aliasing-filter, Hi-Voltage output, output level detector. Moreover, “Advanced switch circuit”, that is ROHM original technology, can reduce various switching noise (ex. No-signal, low frequency likes 20Hz & large signal inputs). “Advanced switch” makes control of microcomputer easier, and can construct high quality car audio system. Features
Reduce switching noise of volume, mute, fader volume, mixing volume, bass, middle, treble, loudness by using advanced switch circuit [Possible to control all steps].
Built-in input selector (single 3 / diff 2).
Decrease the number of external components by built-in 3-band equalizer filter, LPF for subwoofer, loudness filter. And, possible to control Q, Gv, fo of 3-band equalizer and fc of LPF, Gv, fo of 2 loudness by I C BUS control freely.
Built-in mixing volume, Hi-Voltage output.
Built-in anti-aliasing-filter, anti-GSM-noise-filter.
Package is SSOP-B28. Putting input-terminals together and output-terminals together can make PCB layout easier and can makes area of PCB smaller. 2
It is possible to control by 3.3V / 5V for I C BUS.
AEC-Q100 Qualified. Applications
It is the optimal for the car audio. Besides, it is possible to use for the audio equipment of mini Compo, micro Compo, TV etc with all kinds. Key Specifications
Total harmonic distortion:
Maximum input voltage:
Cross-talk between selectors:
Ripple rejection
Output noise voltage:
Residual output noise voltage:
Operating Range of Temperature: package(s) SSOP-B28 0.004%(Typ.) 2.1Vrms(Typ.) 100dB(Typ.) -65dB(Typ.) 6µVrms(Typ.) 4µVrms(Typ.) -40℃ to +85℃ W(Typ.) x D(Typ.) x H(Max.) 10.00mm x 7.60mm x 1.35mm SSOP-B28 Typical Application Circuit Figure 1. Application Circuit Diagram ○Product structure:Silicon monolithic integrated circuit ○This product is not designed protection against radioactive rays www.rohm.com TSZ02201-0C2C0E100010-1-2 © 2013 ROHM Co., Ltd. All rights reserved. 1/44 TSZ22111・14・001 4.OCT.2013 Rev.002 Datasheet BD37034FV-M Pin Configuration SSOP-B28 (TOP VIEW) A1 1 28 VREF A2 2 27 GND B1 3 26 SDA B2 4 25 SCL C1 5 24 VCCL C2 6 23 OUTF1 DP1 7 22 OUTF2 DN 8 21 OUTR1 DP2 9 20 OUTR2 EP1 10 19 OUTS1 EN1 11 18 OUTS2 MIN/EN2 12 17 LOUT/OLD EP2 13 16 LRST/OLDC VCCH 14 15 MUTE Figure 2. Pin configuration Pin Descriptions Terminal Number Terminal Name Terminal Number Terminal Name 1 A1 A input terminal of 1ch 15 MUTE 2 A2 A input terminal of 2ch 16 LRST/OLDC 3 B1 B input terminal of 1ch 17 LOUT/OLD 4 B2 B input terminal of 2ch 18 OUTS2 SW output terminal of 2ch 5 C1 C input terminal of 1ch 19 OUTS1 SW output terminal of 1ch 6 C2 C input terminal of 2ch 20 OUTR2 Rear output terminal of 2ch 7 DP1 D positive input terminal of 1ch 21 OUTR1 Rear output terminal of 1ch 8 DN D negative input terminal 22 OUTF2 Front output terminal of 2ch Description Description External compulsory mute terminal ・Level meter reset terminal ・Filter output terminal of output level detector ・Output terminal for Level meter ・Output terminal of output level detector 9 DP2 D positive input terminal of 2ch 23 OUTF1 10 EP1 E positive input terminal of 1ch 24 VCCL 11 EN1 25 SCL I C Communication clock terminal 12 MIN/EN2 E negative input terminal of 1ch ・Mixing input terminal ・E negative input terminal of 2ch E positive input terminal of 2ch 26 SDA I C Communication data terminal 27 GND GND terminal VCCH terminal for power supply 28 VREF VREF terminal 13 EP2 14 VCCH www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 2/44 Front output terminal of 1ch VCCL terminal for power supply 2 2 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M Block Diagram Figure 3. Block Diagram Absolute Maximum Ratings Parameter Power supply Voltage Symbol Limits Unit VCCL※1 10.0 V VCCH※1 V W ℃ Input Voltage Vin※1 Power Dissipation Pd 13.5 VCCL+0.3 to GND-0.3 Only SCL,SDA 7 to GND-0.3 1.06 ※2 Storage Temperature Tastg -55 to +150 V ※Maximum voltage which can be impressed referencing GND. Operation using batteries which is used in automobiles directly cannot be guaranteed. ※2 This value decreases 8.5mW/℃ for Ta=25℃ or more. ROHM standard board shall be mounted Thermal resistance θja = 117.6(℃/W) ROHM Standard board Size:70×70×1.6(㎣) Material:A FR4 grass epoxy board(3% or less of copper foil area) Operating Range Parameter Power supply voltage Temperature www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 Symbol Limits Unit VCCL 7.0 to 9.5 V VCCH VCCL to 13.0 V Topr -40 to +85 ℃ 3/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M BLOCK Electrical Characteristic Unless specified particularly Ta=25℃, VCCL=VCCH=8.5V, f=1kHz, Vin=1Vrms, Rg=600Ω, RL=10kΩ, A input Input Gain, Volume, Tone control, Loudness, Fader=0dB, LPF, HPF=OFF, Mix OFF, anti-aliasing-filter OFF Limit Item Symbol Unit Condition 49 +1.5 +1.5 mA dB dB 0.004 0.05 % - 0.002 0.05 % VNO1 - 6 12 µVrms Front/Rear Output noise voltage 2 Front/Rear ＊ VNO2 - 16 32 µVrms Subwoofer Output noise voltage 3 Subwoofer ＊ VNO3 - 22 44 µVrms Residual output noise voltage 1＊ VNOR1 - 4 10 µVrms Front/Rear Residual output noise voltage 2 Front/Rear＊ VNOR2 - 11 22 µVrms Subwoofer Residual output noise voltage 3 Subwoofer＊ VNOR3 - 16 32 µVrms Cross-talk between channels ＊ CTC - -100 -85 dB Ripple rejection RR - -65 -40 dB No signal Gv=20log(VOUT/VIN) CB = GV1-GV2 VOUT=1Vrms BW=400-30KHz VCCH=8.5V(Hi-Voltage OFF) VIN=1Vrms BW=400-30KHz VCCH=12V(Hi-Voltage ON) Rg = 0Ω BW = IHF-A VCCH=8.5V(Hi-Voltage OFF) Rg = 0Ω BW = IHF-A VCCH=12V(Hi-Voltage ON) Rg = 0Ω BW = IHF-A VCCH=12V(Hi-Voltage ON) Fader = -∞dB Rg = 0Ω, BW = IHF-A VCCH=8.5V(Hi-Voltage OFF) Fader = -∞dB Rg = 0Ω, BW = IHF-A VCCH=12V(Hi-Voltage ON) Fader = -∞dB Rg = 0Ω,BW = IHF-A VCCH=12V(Hi-Voltage ON) Rg = 0Ω CTC=20log(VOUT/VIN) BW = IHF-A f=1kHz, VRR=100mVrms RR=20log(VCC IN/VOUT) Input impedance RIN 70 100 130 kΩ Maximum input voltage VIM 2.0 2.1 - Vrms Cross-talk between selectors ＊ CTS - -100 -85 dB Common mode rejection ratio ＊ CMRR 46 60 - dB Min. Typ. Max. IQ GV CB -1.5 -1.5 36 0 0 THD+N1 - THD+N2 Output noise voltage 1 ＊ Current upon no signal Voltage gain Channel balance Total harmonic distortion 1 ＊ Input_Selector GENERAL Total harmonic distortion 2 ＊ www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 4/44 VIM at THD+N(VOUT)=1% BW=400-30KHz Rg = 0Ω CTS=20log(VOUT/VIN) BW = IHF-A XP1 and XN input XP2 and XN input CMRR=20log(VIN/VOUT) BW = IHF-A [※X・・・D/E] TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M LOUDN ESS Treble Middle Bass Mute Volume Input Gain BLOCK Limit Item Symbol Min. Typ. Max. Unit Maximum input gain Gv MAX +14 +16 +18 dB Minimum input gain Gv MIN -2 0 +2 dB Gain set error GV ERR1 -2 0 +2 dB Maximum boost gain Gv MAX +13 +15 +17 dB Maximum attenuation ＊ Gv MIN -83 -79 -75 dB Gain set error Attenuation set error GV ERR1 GV ERR2 -2 -2 0 0 +2 +2 dB dB Mute attenuation ＊ GMUTE - -100 -85 dB Maximum boost gain GB BST +13 +15 +17 dB Maximum cut gain GB CUT -17 -15 -13 dB Gain set error GB ERR -2 0 +2 dB Maximum boost gain GM BST +13 +15 +17 dB Maximum cut gain GM CUT -17 -15 -13 dB Gain set error GM ERR -2 0 +2 dB Maximum boost gain GT BST +13 +15 +17 dB Maximum cut gain GT CUT -17 -15 -13 dB Gain set error GT ERR -2 0 +2 dB Maximum gain GL MAX -17 -15 -13 dB Gain set error GL ERR -2 0 +2 dB www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 5/44 Condition Input Gain +16dB VIN=100mVrms Gin=20log(VOUT/VIN) Input Gain 0dB VIN=1Vrms Gin=20log(VOUT/VIN) GAIN=+16to+1dB Volume +15dB VIN=100mVrms Gin=20log(VOUT/VIN) Volume -79dB VIN=2Vrms Gin=20log(VOUT/VIN) GAIN=+15to+1dB ATT=0dBto-79dB Mute ON Gmute=20log(VOUT/VIN) BW = IHF-A Gain=+15dB f=100Hz VIN=100mVrms GB=20log (VOUT/VIN) Gain=-15dB f=100Hz VIN=2Vrms GB=20log (VOUT/VIN) Gain=+15to-15dB f=100Hz Gain=+15dB f=1kHz VIN=100mVrms GM=20log (VOUT/VIN) Gain=-15dB f=1kHz VIN=2Vrms GM=20log (VOUT/VIN) Gain=+15to-15dB f=1kHz Gain=+15dB f=10kHz VIN=100mVrms GT=20log (VOUT/VIN) Gain=-15dB f=10kHz VIN=2Vrms GT=20log (VOUT/VIN) Gain=+15to-15dB f=10kHz Gain -15dB f=800Hz VIN=1Vrms GL=20log(VOUT/VIN) Gain=-15 to-1dB TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet Level Meter OUTPUT Fader/Mix BLOCK BD37034FV-M Limit Item Symbol Min. Typ. Max. Unit Condition Maximum boost gain GF BST +13 +15 +17 dB Fader/Mix=+15dB VIN=100mVrms GF=20log(VOUT/VIN) Maximum attenuation ＊ GF MIN - -100 -85 dB Fader=-∞dB, Mix=OFF GF=20log(VOUT/VIN) BW = IHF-A Gain set error Attenuation set error 1 Attenuation set error 2 Attenuation set error 3 Output impedance GF ERR GF ERR1 GF ERR2 GF ERR3 ROUT -2 -2 -3 -4 - 0 0 0 0 - 2 2 3 4 50 dB dB dB dB Ω Maximum output voltage1 VOM1 2.50 2.75 - Vrms Maximum output voltage2 VOM2 3.75 4 - Vrms Maximum output voltage VL MAX 2.8 3.1 3.5 V Maximum offset voltage VL OFF - 15 100 mV Gain=+15 to +1dB ATT=-1 to -15dB ATT=-16 to -47dB ATT=-48 to -79dB VIN=100 mVrms THD+N=1% BW=400-30KHz VCCH=8.5V, LVS=+3dB (Hi-Voltage OFF) THD+N=1% BW=400-30KHz VCCH=12V(Hi-Voltage ON) *VP-9690A(Average value detection, effective value display) filter by Matsushita Communication is used for * measurement. Phase between input / output is same. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 6/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M Typical Performance Curve(s) 40 10 9 8 30 6 Iq [mA] Iq [mA] 7 20 5 4 3 10 2 1 0 0 7 8 8 9 9 9 10 11 12 13 VCC [V] Figure 5. VCCH vs Iq (VCCL=OPEN) VCC [V] Figure 4. VCCL vs Iq (VCCH=OPEN) 40 10.000 10.000 30 1.000 1.000 0.100 0.100 0.010 0.010 THD+n [%] Iq [mA] 8 10 20 10 0.001 0.001 0 7 8 8 9 9 0.010 0.100 1.000 0.001 10.000 10 Vin [Vrms] VCC [V] Figure 6. VCCL=VCCH vs Iq www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 Figure 7. THD vs Vin / Vo 7/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Vo [Vrms] 7 Datasheet Gain [dB] BD37034FV-M 0 0 -20 -20 Gain [dB] -40 -40 -60 -60 -80 -80 -100 -100 10 100 1000 10000 100000 10 100 Frequency [Hz] 10000 100000 10000 100000 Figure 9. PSRR Figure 8. CMRR 5 5 0 0 Gain [dB] Gain [dB] 1000 Frequency [Hz] -5 -5 -10 -10 -15 -15 -20 -20 10 100 1000 10000 100000 10 Frequency [Hz] 1000 Frequency [Hz] Figure 11. Anti aliasing Filter Figure 10. Loudness www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 100 8/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet 20 20 15 15 10 10 5 5 Gain [dB] Gain [dB] BD37034FV-M 0 0 -5 -5 -10 -10 -15 -15 -20 -20 10 100 1000 10000 100000 10 100 Frequency [Hz] 1000 10000 100000 Frequency [Hz] Figure 13. Middle gain vs frequency Figure 12. Bass gain vs frequency 20 0 15 -20 10 Gain [dB] Gain [dB] 5 0 -40 -60 -5 -10 -80 -15 -20 -100 10 100 1000 10000 100000 10 Frequency [Hz] 1000 10000 100000 Frequency [Hz] Figure 15. LPF Figure 14. Treble gain vs frequency www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 100 9/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M 2 I C BUS CONTROL SIGNAL SPECIFICATION (1) Electrical specifications and timing for bus lines and I/O stages SDA t BUF t t F HD;STA t t t SP R LOW SCL t HD;STA P t HD;DAT t t HIGH t t SU;DAT SU;STA SU;STO Sr S P 2 Figure 16. Definition of timing on the I C-bus 2 Table 1 Characteristics of the SDA and SCL bus lines for I C-bus devices(Ta=25℃, VCCL=8.5V) 2 Fast-mode I C-bus Parameter Symbol Min. Max. 400 1 SCL clock frequency fSCL 0 2 Bus free time between a STOP and START condition tBUF 1.3 － Hold time (repeated) START condition. After this period, the 3 tHD;STA 0.6 － first clock pulse is generated 4 LOW period of the SCL clock tLOW 1.3 － 5 HIGH period of the SCL clock tHIGH 0.6 － 6 Set-up time for a repeated START condition tSU;STA 0.6 － 7 Data hold time tHD;DAT 0 － 8 Data set-up time tSU;DAT 100 － 9 Set-up time for STOP condition tSU;STO 0.6 － Unit kHz µS µS µS µS µS µS ns µS All values referred to VIH min. and VIL max. Levels (see Table 2). 2 Table 2 Characteristics of the SDA and SCL I/O stages for I C-bus devices Parameter 10 11 12 Symbol LOW level input voltage HIGH level input voltage Pulse width of spikes which must be suppressed by the input filter. 13 LOW level output voltage: at 3mA sink current 14 Input current each I/O pin with an input voltage between 0.4V and 4.5V Fast-mode devices Min. Max. Unit VIL VIH -0.3 2.3 1 5 V V tSP 0 50 ns VOL1 0 0.4 V Ii -10 10 µA Figure 17. Command timing example in the I2C data transmission www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 10/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M 2 (2)I C BUS FORMAT S 1bit MSB LSB Slave Address 8bit S Slave Address A Select Address Data P MSB LSB MSB LSB A Select Address A Data A P 1bit 8bit 1bit 8bit 1bit 1bit = Start conditions (Recognition of start bit) = Recognition of slave address. 7 bits in upper order are voluntary. The least significant bit is “L” due to writing. = ACKNOWLEDGE bit (Recognition of acknowledgement) = Select every of volume, bass and treble. = Data on every volume and tone. = Stop condition (Recognition of stop bit) 2 (3)I C BUS Interface Protocol 1)Basic form Slave Address S MSB LSB A Select Address MSB LSB A Data A MSB LSB P 2)Automatic increment(Select Address increases (+1) according to the number of data) S Slave Address A Select Address A Data1 A Data2 A ････ MSB LSB MSB LSB MSB LSB MSB LSB (Example)①Data 1 is set as data of Select Address (20h). ②Data 2 is set as data of Select Address +1 (28h). ③Data N is set as data of Select Address +N-1. DataN MSB 3)Configuration unavailable for transmission (In this case, only Select Address 1 is set.) S Slave Address A Select Address1 A Data A Select Address 2 A Data A MSB LSB MSB LSB MSB LSB MSB LSB MSB LSB (Note)If any data is transmitted as Select Address 2 next to data, It is recognized as data, not as Select Address 2. A P LSB P (4)Slave Address MSB A6 1 A5 0 A4 0 www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 A3 0 A2 0 A1 0 11/44 A0 0 LSB R/W 0 80H TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M (5)Select Address and Data Items Select Address (hex) Initial Setup1 MSB Data D5 D4 Advanced Switch Time of Volume/Fader/Mix /Tone/Loudness LSB D7 D6 01 Advanced Switch ON/OFF Anti Alias Filter ON/OFF LPF Setup 02 LPF Phase 0°/180° Level Meter Reset Initial Setup2 03 Initial Setup3 04 Input Selector 05 Input Gain 06 Volume Gain 20 Volume Gain / Attenuation Fader 1ch Front 28 Fader Gain / Attenuation Fader 2ch Front 29 Fader Gain / Attenuation Fader 1ch Rear 2A Fader Gain / Attenuation Fader 2ch Rear 2B Fader Gain / Attenuation Fader 1ch Sub 2C Fader Gain / Attenuation Fader 2ch Sub 2D Fader Gain / Attenuation Mixing1 Gain 30 Mixing Gain / Attenuation Mixing2 Gain 31 Mixing Gain / Attenuation Bass setup 41 0 0 Bass f0 0 0 Bass Q Middle setup 44 0 0 Middle f0 0 0 Middle Q Treble setup 47 0 0 Treble f0 0 0 Subwoofer Output Selector Mixing Input Selector 1ch Mix Input sel Full-diff Type MUTE ON/OFF Bass Boost/Cut Middle Boost/Cut Treble Boost/Cut Bass Gain 51 Middle Gain 54 Treble Gain 57 Loudness Gain 75 0 D3 D2 Level Shift Hi-voltage ON/OFF Subwoofer Input Selector1 Advanced Switch Time of Mute 0 2ch Mix Input sel Rear Input Selector 0 0 Input Selector 0 0 Input Gain 0 0 Bass Gain 0 0 Middle Gain 0 0 Treble Gain Level Meter ON/OFF 0 Subwoofer Input Selector2 HICUT D0 Subwoofer LPF fc Loudness f0 Front Input Selector D1 HPF fc 0 Treble Q Loudness Gain Output Level Detector Initial Setup4 Initial Setup5 90 0 0 A0 A1 0 0 0 0 Threshold Level Select 0 0 0 0 OUT F1 ON/OFF 0 0 OUT F2 ON/OFF 0 0 OUT R1 ON/OFF 0 0 OUT R2 ON/OFF 0 0 Initial Setup6 A2 0 1 0 1 0 0 0 1 Initial Setup7 System Reset A3 FE 0 1 0 0 1 0 0 0 0 0 0 0 0 0 0 1 : Advanced Switch ※(Set up bit (It is written with “0” by the above table) which hasn’t been used in “0”. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 12/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M Note 1. In function changing of the hatching part, it works Advanced switch.. 2. Upon continuous data transfer, the Select Address is circulated by the automatic increment function, as shown below. 3. For the function of input selector and subwoofer input select etc, it is not corresponded for advanced switch. Therefore, please apply mute on the side of a set when changes these setting. 4. When using mute function of this IC at the time of changing input selector, please switch mute ON/OFF for waiting advanced-mute time. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 13/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M Select address 01(hex) Function Name Advanced Switch Time of Mute Hi-voltage ON/OFF Level Shift Advanced Switch Time of Volume /Fader /Tone/Loudness Anti Alias Filter ON/OFF Advanced Switch ON/OFF Select address 02(hex) Default:8’ha4 Mode MSB D7 0.6msec 1.0msec 1.4msec 3.2msec OFF ON 0dB +3dB 4.7msec 7.2msec 11.2msec 14.4msec OFF ON OFF ON D6 D5 Initial Setup D4 D3 Mode Subwoofer LPF fc 55Hz 85Hz 120Hz 160Hz PASS Level Meter Reset (*1) LPF Phase 0°/180° (*2) LSB D0 0 1 0 1 D1 0 0 1 1 0 0 1 1 LSB D0 0 1 0 1 0 1 0 1 0 1 0 1 0 0 1 1 0 1 0 1 0 1 0 1 MSB D7 D6 D5 LPF Setup D4 D3 Prohibition Subwoofer Output Selector D1 0 0 1 1 Default:8’h00 Function Name Subwoofer Input Selector1 D2 Loudness Input Selector Subwoofer 1ch(S1/S1) Front(F1/F2) Rear(R1/R2) Subwoofer(S1/ S2) Hold Reset 0° 180° D2 0 0 0 0 1 1 1 1 0 1 0 0 0 1 1 0 1 1 0 1 0 1 : Initial condition (*1): If “Level Meter Reset” is set as Reset(“b1), a reset pulse will be outputted only once to a level meter block. Also about this register, after a reset pulse output returns to a Hold(“b0) state, without holding a Reset(“b1) state. Therefore, in order to change into a Hold state, it is not necessary to carry out a register setup again. (*2): If Subwoofer LPF fc is set as 「PASS」('b000), LPF PHASE is compulsorily fixed to 0°('b0). www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 14/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M Select address 03(hex) Function Name Level Meter ON/OFF(*1) Default:8’h01 Pin 1p 1n 2n 2p Output Level Detector Mode Level Meter Mode 400Hz 800Hz 2400Hz Prohibition Loudness f0 Mix Mixing Input Selector (*2) MSB D7 Mode MIN_ EN2 A_Single D_Diff B_Single E_Diff E_Full-diff Prohibition A1 DP1 DN B1 EP1 EN1 EN MIN_ EN2 EP1 1 Prohibition D6 Initial Setup2 D4 D3 D5 0 0 1 1 MIN_E N2 A2 DP2 B2 EP2 EP2 0 0 0 0 1 1 0 0 1 1 0 0 0 1 0 1 0 1 1 1 1 1 0 1 D2 LSB D0 0 1 D1 0 1 0 1 (*1): When you use “Output level detector”, please set this register of D0 as 0. Since “Level Meter” and “Output Level Detector” are sharing the terminal, concurrent use is impossible. Default setup is “Level Meter” D0 16pin 17pin 0 OLDC Filter output terminal of output level detector 1 LRST Level meter reset terminal OLD LOUT Output terminal of output level detector Output terminal for Level meter (*2): When you set Mixing Input Selector as “Mix”('b000), please do not set input Selector(Select Address 05, D0 to D4) as “E_Full_Diff”(’b 01000). When you set Mixing Input Selector as “E_Diff”('b101), please do not set input Selector(Select Address 05, D0 to D4) as “E_Full_Diff”(’b 01000). When you set Mixing Input Selector as “E_Full_Diff”(’b110), please do not set input Selector(Select Address 05, D0 to D4) as “E_Diff”(’b 00111). Select address 04(hex) Function Name HPF fc Subwoofer Input Selector2 Front Input Selector Rear Input Selector 1ch Mixing Input Selector 2ch Mixing Input Selector Default:8’h80 Mode 55Hz 85Hz 120Hz 160Hz Subwoofer Input Selector1 LPF ON HPF ON Prohibition Loudness HPF ON Loudness HPF ON 1ch 2ch 1ch 2ch MSB D7 D6 D5 HPF Setup D4 D3 D2 0 0 0 1 1 1 0 1 D1 0 0 1 1 LSB D0 0 1 0 1 0 1 0 1 0 1 0 1 : Initial condition www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 15/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M Select address 05(hex) Function Mode Name A_Single B_Single C_Single D_Single E1_Single Input Selector E2_Single (*1) D_Diff E_Diff E_Full_Diff Full-diff Type Pin 1p 1n 2n A1 B1 C1 DP1 EP1 EN2 DP1 EP1 DN EP1 EN1 Proibition Input short Negative input Bias 2p A2 B2 C2 DP2 EN1 EP2 DP2 EP2 EP2 Default:8’h00 MSB D7 D6 D5 Initial Setup2 D4 D3 D2 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0 1 0 0 1 0 1 0 Other setting 0 1 0 Function Name Input Gain Mute ON/OFF Gain 0dB 1dB 2dB 3dB 4dB 5dB 6dB 7dB 8dB 9dB 10dB 11dB 12dB 13dB 14dB 15dB 16dB (16dB) (16dB) (16dB) (16dB) Prohibition OFF ON Default:8’ha0 MSB D7 LSB D0 0 1 0 1 0 1 0 1 0 0 1 0 1 (*1): There is combination which shares an input terminal depending on the combination of “Input Selector” (Select Address 05, D0 to D4) and “Mixing Input Selector” (Select Address 03, D5 to D7). Be careful not to set up the following combination. Input Selector Mixing Input Selector Pin Pin Mode Mode 1p 1n 2n 2p 1p 1n 2n MIN_EN2 MIN_EN2 E_Full_Diff EP1 EN1 EP2 Mix MIN_EN2 E_Full_Diff EP1 EN1 EP2 E_Diff EP1 EN1 MIN_EN2 E_Diff EP1 EN1 EP2 E_Full_Diff EP1 EN1 Select address 06 (hex) D1 0 0 1 1 1 1 1 1 0 D6 D5 Input Selector D4 D3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 0 1 0 1 0 1 0 1 0 D2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 Other setting D1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 2p MIN_EN2 EP2 EP2 LSB D0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 0 1 : Initial condition www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 16/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M Select address 20 (hex) Function Name D6 0 D5 0 Volume Gain D4 D3 0 0 D2 0 D1 0 LSB D0 0 Prohibition … … … … … … … … Volume Gain Default:8'h00 MSB Mode D7 0 +15dB +14dB +13dB +12dB +11dB +10dB +9dB +8dB +7dB +6dB +5dB +4dB +3dB +2dB +1dB -0dB -1dB -2dB -3dB -4dB -5dB -6dB -7dB -8dB -9dB -10dB -11dB -12dB -13dB -14dB -15dB -16dB -17dB -18dB -19dB -20dB 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 : Initial condition www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 17/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M Function Name Mode Volume Gain -21dB -22dB -23dB -24dB -25dB -26dB -27dB -28dB -29dB -30dB -31dB -32dB -33dB -34dB -35dB -36dB -37dB -38dB -39dB -40dB -41dB -42dB -43dB -44dB -45dB -46dB -47dB -48dB -49dB -50dB -51dB -52dB -53dB -54dB -55dB -56dB -57dB -58dB -59dB -60dB -61dB -62dB -63dB -64dB -65dB -66dB -67dB -68dB -69dB -70dB www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 MSB D7 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 D6 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 D5 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 18/44 Volume Gain D4 D3 1 0 1 0 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 D2 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 D1 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 LSB D0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet … '-79dB 1 1 1 1 1 1 1 1 … Prohibition -71dB -72dB -73dB -74dB -75dB -76dB -77dB -78dB -79dB 1 1 1 1 1 1 0 1 D2 0 D1 0 LSB D0 0 … LSB D0 1 0 1 0 1 0 1 0 1 0 … D1 1 0 0 1 1 0 0 1 1 0 … D2 1 0 0 0 0 1 1 1 1 0 … Volume Gain D4 D3 0 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 0 … D5 0 0 0 0 0 0 0 0 0 0 Mode … D6 1 1 1 1 1 1 1 1 1 1 … Volume Gain MSB D7 1 1 1 1 1 1 1 1 1 1 … Function Name … BD37034FV-M 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 19/44 … … … … … Select address 28, 29, 2A, 2B, 2C, 2D, 30, 31(hex) Default:8'hFF MSB Fader / Mixing Gain Mode Function Name D7 D6 D5 D4 D3 0 0 0 0 0 Prohibition 0 1 1 1 0 +15dB 0 1 1 1 0 +14dB 0 1 1 1 0 +13dB 0 1 1 1 0 +12dB 0 1 1 1 0 +11dB 0 1 1 1 0 Fader/Mixing +10dB 0 1 1 1 0 Gain +9dB 0 1 1 1 0 +8dB 0 1 1 1 1 +7dB 0 1 1 1 1 +6dB 0 1 1 1 1 +5dB 0 1 1 1 1 +4dB 0 1 1 1 1 +3dB 0 1 1 1 1 +2dB 0 1 1 1 1 +1dB 0 1 1 1 1 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M Function Name Mode Fader/Mixing Gain -0dB -1dB -2dB -3dB -4dB -5dB -6dB -7dB -8dB -9dB -10dB -11dB -12dB -13dB -14dB -15dB -16dB -17dB -18dB -19dB -20dB -21dB -22dB -23dB -24dB -25dB -26dB -27dB -28dB -29dB -30dB -31dB -32dB -33dB -34dB -35dB -36dB -37dB -38dB -39dB -40dB www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 MSB D7 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 D6 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 D5 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 20/44 Fader Gain D4 D3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 D2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 D1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 LSB D0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet D6 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 D5 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Fader Gain D4 D3 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 0 D2 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 D1 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 LSB D0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 Prohibition … … … … … … Fader/Mixing Gain MSB D7 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 … Function Name … BD37034FV-M MUTE 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 1 Mode -41dB -42dB -43dB -44dB -45dB -46dB -47dB -48dB -49dB -50dB -51dB -52dB -53dB -54dB -55dB -56dB -57dB -58dB -59dB -60dB -61dB -62dB -63dB -64dB -65dB -66dB -67dB -68dB -69dB -70dB -71dB -72dB -73dB -74dB -75dB -76dB -77dB -78dB -79dB : Initial condition www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 21/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M Select address 41(hex) Mode Function Name Bass Q Bass f0 Middle Q Middle f0 Mode Treble Q Treble f0 Mode 0.75 1.25 7.5kHz 10kHz 12.5kHz 15kHz D5 0 0 1 1 Default:8’h00 MSB D7 D6 0.75 1.00 1.25 1.50 0.5kHz 1kHz 1.5kHz 2.5kHz Select address 47(hex) Function Name D6 0.5 1.0 1.5 2.0 60Hz 80Hz 100Hz 120Hz Select address 44(hex) Function Name Default:8’h00 MSB D7 D5 0 0 1 1 Default:8’h00 MSB D7 D6 D5 0 0 1 1 Bass setup D4 D3 D2 D1 0 0 1 1 LSB D0 0 1 0 1 D2 D1 0 0 1 1 LSB D0 0 1 0 1 D2 D1 0 1 0 1 Middle setup D4 D3 0 1 0 1 Treble setup D4 D3 LSB D0 0 1 0 1 0 1 : Initial condition www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 22/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M Select address 51, 54, 57(hex) Function Name Bass /Middle /Treble Gain Bass/Middle/Treble Boost/Cut Mode 0dB 1dB 2dB 3dB 4dB 5dB 6dB 7dB 8dB 9dB 10dB 11dB 12dB 13dB 14dB 15dB (15dB) (15dB) (15dB) (15dB) (15dB) Prohibition Boost Cut Select address 75(hex) Function Name Loudness Gain Loudness HICUT Mode 0dB 1dB 2dB 3dB 4dB 5dB 6dB 7dB 8dB 9dB 10dB 11dB 12dB 13dB 14dB 15dB (15dB) (15dB) (15dB) (15dB) (15dB) Prohibition HICUT1 HICUT2 HICUT3 HICUT4 Default:8'h80 MSB D7 D6 D5 Bass/Middle/Treble Gain D4 D3 D2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0 1 0 0 1 0 1 0 0 1 0 0 1 0 0 1 0 0 1 1 0 1 1 0 1 1 0 1 1 1 0 0 1 0 0 1 0 0 1 0 0 1 0 1 other setting D1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 LSB D0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 D1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 LSB D0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 0 1 Default:8'h00 MSB D7 D6 0 0 1 1 D5 Loudness Gain D4 D3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 0 1 0 1 0 1 0 1 0 D2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 other setting 0 1 0 1 : Initial condition www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 23/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M Select address 90(hex) Function Name Mode OUT R2 ON/OFF OUT R1 ON/OFF OUT F2 ON/OFF OUT F1 ON/OFF OFF ON OFF ON OFF ON OFF ON ±30mV ±45mV ±60mV ±75mV Threshold Level Select Default:8'h00 MSB D7 D6 D5 Output Level Detector D4 D3 D2 D1 LSB D0 0 1 0 1 0 1 0 1 0 0 1 1 0 1 0 1 : Initial condition www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 24/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M Recommendation of VOLUME DIAGRAM The example of the SET VOLUME DIAGRAM by Volume(SelectAddress 20(hex)) and Fader(SelectAddress 28,29,2A,2B,2C, 2D(hex)) is explained in the following. Example 1 ) It is recommended when a signal level is made to attenuate, a decline by Volume is done by -24dB. It is adjusted with Fader after -24dB. S/N ratio can improve in comparison with the case that it is made to attenuate only with Volume. Display (※) 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 Total Gain [dB] 6 5 4 3 2 1 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -11 -12 -13 -14 -15 -16 -17 -18 Volume [dB] 6 5 4 3 2 1 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -11 -12 -13 -14 -15 -16 -17 -18 Fader [dB] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Display (※) 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Total Gain [dB] -19 -20 -21 -22 -23 -24 -26 -28 -30 -32 -34 -36 -38 -40 -42 -44 -46 -48 -50 -52 -54 -56 -58 -60 -62 -∞ Volume [dB] -19 -20 -21 -22 -23 -24 -24 -24 -24 -24 -24 -24 -24 -24 -24 -24 -24 -24 -24 -24 -24 -24 -24 -24 -24 Mute Fader [dB] 0 0 0 0 0 0 -2 -4 -6 -8 -10 -12 -14 -16 -18 -20 -22 -24 -26 -28 -30 -32 -34 -36 -38 Mute Table 1. A decline by Volume is done by -24dB. It is adjusted with Fader after -24dB. (※Display=SET VOLUME) www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 25/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M ※When a attenuate after -32dB is used with Volume, in case of use Subwoofer Input Selector = Input Selector (Select Address 02(hex), D3 = 1), Output level of OUTS1/S2 is attenuated 「 Volume – (-31dB) 」. Figure 18. Subwoofer Input Selector = Input Selector (SelectAddress 02(hex), D3 = 1) Volume [dB] Volume [dB] OUTS1/S2 [dB] Select Address 20(hex) Subwoofer Input Selector=Loudness (Select Address 02(hex), D3=0) 6 5 4 3 2 1 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -11 -12 -13 -14 -15 -16 -17 -18 6 5 4 3 2 1 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -11 -12 -13 -14 -15 -16 -17 -18 Subwoofer Input Selector= Input Selector (Select Address 02(hex), D3=1) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 OUTS1/S2 [dB] Select Address 20(hex) Subwoofer Input Selector=Loudness (Select Address 02(hex), D3=0) -19 -20 -21 -22 -23 -24 -26 -28 -30 -32 -34 -36 -38 -40 -42 -44 -46 -48 -50 -52 -54 -56 -58 -60 -62 -19 -20 -21 -22 -23 -24 -26 -28 -30 -32 -34 -36 -38 -40 -42 -44 -46 -48 -50 -52 -54 -56 -58 -60 -62 Subwoofer Input Selector= Input Selector (Select Address 02(hex), D3=1) 0 0 0 0 0 0 0 0 0 -1 -3 -5 -7 -9 -11 -13 -15 -17 -19 -21 -23 -25 -27 -29 -31 Table 2. Subwoofer Input Selector = Input Selector (Select Address 02(hex), D3 = 1) Volume attenuation vs Output Level of OUTS1/S2 www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 26/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M About loudness When Loudness is set up in on, signal level in fo (set up by (Select Address 03(hex), D3,D4))is attenuated) is made attenuated. Therefore to make it put emphasis on the low and high band, use volume together Loudness=OFF(Select Address 75 : D4 to D0 = 0dB) Loudness=ON(Select Address 75 : D4 to D0 = 14dB) Figure 19. Loudness gain vs frequency (fo=800Hz) Display (※) 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 Total Gain A [dB] 6 5 4 3 2 1 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -10 -10 -10 -10 -10 -10 -10 -10 Total Gain B [dB] 6 5 4 3 2 1 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -10 -10 -10 -10 -10 -10 -10 -10 Volume [dB] Loudness [dB] Fader [dB] Display (※) 6 5 4 3 2 1 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -10 -10 -10 -10 -10 -10 -10 -10 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 -1 -2 -3 -4 -5 -6 -7 -8 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Total Gain A [dB] -10 -10 -10 -10 -10-10 -10 -12 -14 -16 -18 -20 -22 -24 -26 -28 -30 -32 -34 -36 -38 -40 -42 -44 -46 -48 -∞ Total Gain B [dB] -19 -20 -21 -22 -23 -24 -26 -28 -30 -32 -34 -36 -38 -40 -42 -44 -46 -48 -50 -52 -54 -56 -58 -60 -62 -∞ Volume [dB] Loudness [dB] Fader [dB] -10 -10 -10 -10 -10 -10 -10 -10 -10 -10 -10 -10 -10 -10 -10 -10 -10 -10 -10 -10 -10 -10 -10 -10 -10 Mute -9 -10 -11 -12 -13 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 0 0 0 0 0 0 -2 -4 -6 -8 -10 -12 -14 -16 -18 -20 -22 -24 -26 -28 -30 -32 -34 -36 -38 Mute Table 3. A decline by Volume is done by -24dB. It is adjusted with Fader after -24dB. Loudness=ON (※Display=SET VOLUME) www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 27/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M Total Gain A Total Gain B Figure 20. Gain vs frequency of Table.3 Attention about Loudness ON/OFF To make it put emphasis on the low and high band, when it is made to boost with Volume so long as it was made to attenuate with Loudness. ・Loudness OFF →ON : ・Loudness ON →OFF : Send data of loudness before volume Send data of volume before loudness ※Transmit data in the above turn. A signal level declines first, and it is amplified after that. And so natural switching can be realized. Figure 21. example of data sending about Loudness ON/OFF www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 28/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M (6)About power on reset At on of supply voltage circuit made initialization inside IC is built-in. Please send data to all address as initial data at supply voltage on. And please supply mute at set side until this initial data is sent.) Limit Item Symbol Unit Condition Min. Typ. Max. － － Rise time of VCCL Trise 33 usec VCCL rise time from 0V to 5V) VCCL voltage of release － － Vpor 4.1 V power on reset (7)About external compulsory mute terminal Mute is possible forcibly than the outside after input again department, by the setting of the MUTE terminal. Mute Voltage Condition Mode GND to 1.0V MUTE ON 2.3V to 5.0V MUTE OFF Establish the voltage of MUTE in the condition to have been defined.) About OUT-terminal(18to23pin) vs. VCCL Output voltage of OUT terminal(18to23pin) keep fixed voltage in operational range(VCCL=7.0Vto9.5V). Figure 22. OUT(18 to 23pin)_DC-Bias = 4.15V fixed.(Hi-Voltage Mode = OFF) Figure 23. OUT(18 to 23pin)_DC-Bias = 6.0V fixed.(Hi-Voltage Mode = ON) www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 29/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M About Advanced switching circuit 【1】About Advanced switch 1-1. Effect of Advanced switch It is the ROHM original technology for prevention of switching noise. When gain switching such as volume and tone control is done momentarily, a music signal doesn’t continue, and unpleasant shock noise is made. Advanced switch can reduce shock noise with the technology which signal wave shape is changed to gently so that a music signal may not continue drastically. select slave data Gain is made to change right after the data transmission momentarily. At this time, a change of DC occurs only in the one for the difference of the amplitude I2C BUS 80 before and after the change.. The technology made to make this change slow a change of DC Wave of Advanced switching Advanced switch starts switching after the control data transmitted by a microcomputer are received. It takes one fixed time, and wave shape transits as the above figure. The data transmitted by a microcomputer are processed inside, and the most suitable movement is done inside the IC so that switching shock noise may not be made.) But, it presumes by the transmitting timing when it doesn’t become intended switching wave shape because it is the function which needs time. The example which relations with the switching time of the data transmitting timing and the reality were shown in is given to it in the following. It asks for design when it is confirmed well. About a kind of transmission method ・A data setup (by the data format, the thing which isn’t indicated by gray) except for the item for advanced switch There is no regulation in transmission specially. ・The data setup (by the data format, the thing which gray indication is) of the item for advanced switch Though there is no regulation in data transmission, the switching order when data are transmitted to several blocks follows the next 2-3. 【2】About transmission DATA of advanced switching item 2-1. About switching time of advanced switch advanced switch ON/ OFF is set up in ON to make advanced switch function effective. And, though it becomes the same completely, the movement time of advanced switch can set up only MUTE in the independence. As for these, set it up referring to select address 01(hex) of the data format. There are transition time to be equivalent to the setup value, and treatment time (effect-less time) inside the IC in advanced switch. Therefore, actual switching time (Tsoft and Tsoft, MUTE) is defined as follows. The treatment time of around 1 time needs the time of 2 times of the setup value The treatment time of around 1 time of MUTE becomes the same time as the setup value (movement time). (Example : in the case of (movement time). (Example : in the case of 11.2msec, 22.4msec) 3.2msec, with OFF? on, each ON? off, 3.2msec Tsoft=setup value × 2 Tsoft,MUTE Tsoft,MUTE MUTE advanced switching time Advanced switching time MUTE ON time switching time MUTE OFF time Setup value 11.2msec should be recommended in switch time of advanced switch. But, when a shock noise level during gain switching isn’t sufficient, it has the possibility that it can be reduced by setting it up more this long on the actual use. But, be careful because an response in switching of around one time becomes slow when you lengthen time. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 30/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M 2-2. About the data transmitting timing in same block state and the switching movement. ■ Transmitting example 1 A time chart to the switching start has become the next since the data transmission. The interval of the same blocks is fully left, and the example when data are transmitted is shown first. And, as for enough interval, it becomes the time when setup time was multiplied by the dispersion margin 1.4. sl a ve s e le ct AK S d a ta (F 1 0d B ) 80 I2 C B U S 28 (F 1 – IN F d B) 80 80 28 FF Tso ft×1 .4 m se c A dv a n ced sw itch tim e F a d e r Ｆ 1 s w itc h tim e Fa d e r Ｆ 1 sw it ch tim e F a d e r_ F1 o utp u t ■ Transmitting example 2 Next, when a transmitting interval isn’t sufficient, the example of (When it is shorter than the above interval.) is shown. The next switching movement is started in succession after that movement is finished when data are transmitted during the first switching movement. sl a ve s e le ct AK S d a ta (F 1 0d B ) I2 C B U S 80 28 (F1 –IN Fd B ) 80 80 28 FF A dv a n ced sw itch tim e F a d e r_Ｆ 1 sw itch tim e Fa d e r_ Ｆ 1 sw it ch tim e Fa d e r_ F 1 o ut p ut ■ Transmitting example 3 Next, the example of the switching movement when a transmitting interval was shortened more is shown. It has the buffer which memorizes data inside the IC, and a buffer always does transmitting data. But, data of +6dB which transmitted to the second become invalid with this example to hold only the latest data. This is invalid as a result. (FaderF1 I2C BUS 80 Only an end is effective in the data transmitted during F1 switching. 0dB) 28 80 (FaderF1 +6B) 80 28 06 (FaderF1 -6B) 80 288 86 Replacement F1 built-in buffer(memory) 0dB +6dB Data of 0dB received : -8 ->0dB -6dB Data of -6dB received from buffer : 0dB->-6dB Advanced switch time FaderF1 switch time www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 FaderF1 switch time 31/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M ■ Transmitting example 4 As for handling of refresh-data, advanced switch movement isn’t started to judge for present setup data and a difference that to be inside the IC) (FaderF1 0dB) (FaderF1 0dB) 80 I2C BUS 28 80 80 28 80 Refresh data Because receiving refresh-data, advanced switch doesn't start. Advanced switch time FaderF1 switch time 2-3. About the data transmitting timing in several block state and the switching movement.) When data are transmitted to several blocks, treatment in the BS (block state) unit is carried out inside the IC. The movement start order of advanced switch is decided by BS in advance.) Select Address Figure 24. The order of advanced switch start ※It is possible in the block in the same BS that switching is started at the same timing. ■Transmitting example 5 2 The timing of the switching start follows the figure of the former page though there is no restriction of the I C BUS data transmitting timing as it explained in the former knot even if it is related to the transmission to several blocks. Therefore, it isn’t based on the data transmitting order, and an actual switching turn becomes the turn of the upper figure. (Transmitting example 6) Each block data is being transmitted with the transmitting example 5 separately. But, it becomes the same result even if data are transmitted in bulk.) slave select (FaderF1 I2C BUS 80 28 data AKS 0dB) (FaderR1 20 80 2A 0dB) 80 (FaderS1 80 2C 0dB) 80 Start afte r advanced switch of FaderF1 Start after advanced switch of FaderR1 Advanced switch ti me Fader F1 switch time F1 output www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 Fader F1 switch time Fader R1 switch time R1 output Fader R1 switch time Fader S1 switch time Fader S1 switch time S1 o utput 32/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M ■Transmitting example 6) Switching of the next BS is done after the present switching completion when an actual switching order is different from the transmitting order, and data except for the same BS are transmitted at the timing when advanced switch movement isn’t finished.) slave select data (FaderF1 0dB) 80 I2C BUS 28 (FaderS1 0dB) 80 80 2C (FaderR1 0dB) 80 80 2A 80 Advanced switch time Fader F1 switch time Fader R1 switch time Fader S1 switch time The case that the same BS3 and BS2 were transmitted during BS1 switching is shown with the next example. (Transmitting example 7) ■Transmitting example 7 The different d a ta (TRE) of the same on e g roup in advan ced switch in (R1 ) a re tra nsmitted. BS1 (Fa derF1 80 I2C BUS 28 BS3 (Treble +6 dB) 0dB) 80 80 57 06 BS2 (Fa de rR1 80 2A 0dB) The d ata (S1) of the next gro up are tran smitte d in su ccession. 80 R 1 b uilt-in buffer 6dB TR E built-in b uffe r 0dB re ceive d -8 ->0d B 0dB receive d fro m buffer –IN F->0 dB 6 dB receive d fro m b uffer 0dB->+6dB Ad vanced switch tim e FaderF1 switch time Fa derR1 switch time Treb le switch time 2-4.About Gain switch of TONE(Bass/Middle/Treble) It becomes two-step transition movement that it passed through 0dB 【 Gain of Bass/Middle/Treble 】 to prevent the occurrence of the switching noise when Gain is changed from boost to the cut (or, from the cut, boost). And, when boost/cut doesn’t change, it is the same as 【 2-2 】【 2-3 】. But, it is in the same way as other switching as advanced switch switching time.) ■Transmitting example 8 When it is changed Bass+15dB from Bass-15dB. (Initial : Bass -15dB) (BA S + 15dB ) I2C US I2 C B BUS 80 51 0F T soft =setup time× 2 A dvan ced switch tim e Bass sw itch tim e -15dB -> 0dB Bass switch tim e 0dB ->+15dB Ba ss outpu t www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 33/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M 【3】About advanced switch of MUTE Advanced switch of MUTE is controllable independently of other advanced switch. There is no regulation about the timing to which MUTE is applied, and the timing to cancel. ■Transmitting example 9 Normal MUTE ON/OFF （MUTE ON） I2C BUS 80 02 (MUTE OFF) 80 01 02 00 Advanced switch time MUTE switch time ■Transmitting example 10 The movement when it was canceled earlier than advanced switch time of MUTE (MUTE OFF) （MUTE ON） I2C BUS 80 02 01 MUTE switch time 80 02 00 Advanced switch time MUTE switch time www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 MUTE switch time 34/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M ■Advanced switch transmitting timing list (1) 【 MUTE 】 Stand-by advanced switch working advanced switch Data transfer timing No constraint No constraint Operation start timing After send data After send data Advanced switch time Tsoft_MUTE※1 Tsoft_MUTE (2) 【 VOL/FAD(F1,F2,R1,R2,S1,S2)/MIX(M1,M2)/TONE(BAS,MID.TRE,LOUD) 】 Stand-by advanced switch working advanced switch Data transfer timing No constraint No constraint Operation start timing After send data After finished current work Advanced switch time Tsoft※2 Tsoft (3) 【 TONE BOOST ⇔ CUT 】 Stand-by advanced switch working advanced switch Data transfer timing No constraint No constraint Operation start timing After send data After finished current work Advanced switch time Tsoft※3 Tsoft ※1 As for Tsoft,MUTE, mentioned advanced switch of MUTE movement time is expressed to the data format. It is equivalent by the explanation in the body in one block. ※2 As for Tsoft, the time of two times of mentioned advanced movement time is expressed to the data format. It changes to block it in the same way by the explanation in the body by the continuance twice. ※3 About Tsoft of TONE BOOST ⇔ CUT, advanced switch treatment time is in the same way as the switching time of the above (※2) though two times hang on the movement time because this movement comes to switch that it passes through 0dB automatically inside the IC. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 35/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M About Output level detector Output level detector is circuit for detection whether output level of IC are into threshold level. 2 You can select output of detection by “block selects (I C control)”. 2 When output level are into threshold level that selected by “Threshold level select (I C control)”,output level of OLD is “H”(3.3V). Figure 25. Block diagram of output level detector Select address 90(hex) Function Name Mode OUT R2 ON/OFF OUT R1 ON/OFF OUT F2 ON/OFF OUT F1 ON/OFF OFF ON OFF ON OFF ON OFF ON ±30mV ±45mV ±60mV ±75mV Threshold Level Select MSB D7 D6 D5 Output Level Detector D4 D3 D2 D1 LSB D0 0 1 0 1 0 1 0 1 0 0 1 1 Please set Select Address 90(hex), D3toD0=0,0,0,0 0 1 0 1 at Output Level Detector OFF. COLD = C1×Zin / ROLD C1 : Coupling capacitance between output of BD37034FV-M and input of power-amp. Zin : Input impedance of power-amp ROLD : Input impedance of OLDC-port Select Address 90(hex) Input impedance is 20kΩ at Output level detector OFF(Select Address 90(hex) D3toD0=0,0,0,0). www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 36/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M Application Circuit Diagram Figure 26. Application Circuit Diagram Unit R : [Ω] C : [F] Notes on wiring ① ② ③ ④ ⑤ Please connect the decoupling capacitor of a power supply in the shortest distance as much as possible to GND. Lines of GND shall be one-point connected. Wiring pattern of Digital shall be away from that of analog unit and cross-talk shall not be acceptable. Lines of SCL and SDA of I2C BUS shall not be parallel if possible. The lines shall be shielded, if they are adjacent to each other. Lines of analog input shall not be parallel if possible. The lines shall be shielded, if they are adjacent to each other. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 37/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M Thermal Derating Curve About the thermal design by the IC Characteristics of an IC have a great deal to do with the temperature at which it is used, and exceeding absolute maximum ratings may degrade and destroy elements. Careful consideration must be given to the heat of the IC from the two standpoints of immediate damage and long-term reliability of operation. Reference data SSOP-B28 Power Dissipation Pd(W) 1.5 Measurement condition: ROHM Standard board board Size:70×70×1.6(㎣) material:A FR4 grass epoxy board (3% or less of copper foil area) 1.063W 1.0 θja = 117.6℃/W 0.5 0.0 0 25 50 75 85 100 125 150 Ambient Temperature Ta(℃) Figure 27. Temperature Derating Curve Note) Values are actual measurements and are not guaranteed. Power dissipation values vary according to the board on which the IC is mounted. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 38/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M Terminal Equivalent Circuit and Description Terminal Terminal Terminal No. Name Voltage Equivalent Circuit Terminal Description VCCL 1 A1 2 A2 3 B1 4 B2 5 C1 6 C2 A terminal for signal input. The input impedance is 100kΩ(typ). 4.15 100KΩ GND A terminal for signal input. VCC 7 DP1 8 DN 9 DP2 10 EP1 11 EN1 13 EP2 The input impedance is 100kΩ(typ). 4.15 100KΩ GND Anti ESD A terminal for signal input. VCC The input impedance is 100kΩ(typ). 12 MIN EN2 4.15 100KΩ GND Anti ESD A terminal for external compulsory mute. If terminal voltage is High level, the mute is off. And if the terminal voltage is Low level, the mute is on. VCCL 5V 1 25k 15 MUTE Anti-ESD 1 .3 V 250 k GND A terminal for fader and Subwoofer output. VCC 18 OUTS2 4.15/6.0 19 OUTS1 20 OUTR2 21 OUTR1 HiVoltage 22 OUTF2 =OFF/ON 23 OUTF1 GND The figure in the pin explanation and input/output equivalent circuit is reference value, it doesn’t guarantee the value. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 39/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M Terminal Terminal Terminal No. Name Voltage Equivalent Circuit Terminal Description 2 VCCL 25 SCL A terminal for clock input of I C BUS communication. - 1.65V GND 2 - 26 A terminal for data input of I C BUS communication. VCCL SDA 1.65V GND Voltage for reference bias of analog signal system. The simple pre-charge circuit and simple discharge circuit for an external capacitor are built in. VCCL 28 VREF 12.5k 4.15 GND 24 VCCL 8.5 14 VCCH 8.5/12 27 GND 0 Power supply terminal. Ground terminal. The figure in the pin explanation and input/output equivalent circuit is reference value, it doesn’t guarantee the value. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・ 15・ 001 40/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M Terminal Terminal Terminal No. Name Voltage Equivalent Circuit Terminal Description VCC LRST A terminal for level meter reset. If terminal voltage is High level, the reset is on. And if the terminal voltage is Low level, the reset is off. - 1.65V 100k GND 16 A terminal for filter of output level detector. VCCL Input impedance is 25k(OUTF/R both ON) or 50kΩ(OUTF/R either ON) at Output level detector ON, 20kΩ at Output level detector OFF. 4.15/ 4.73 OLDC HiVoltage 50k 50k =OFF/ON OUTF2/R2 GND A terminal for Level meter output. VCC 1.5k LOUT 10k GND A terminal for output of output level detector. 17 VCCL 3.3 V OLD 0 1.5k 3.3 GND The figure in the pin explanation and input/output equivalent circuit is reference value, it doesn’t guarantee the value. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・ 15・ 001 41/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M Notes for use 1.Absolute maximum rating voltage When it impressed the voltage on VCC more than the absolute maximum rating voltage, circuit currents increase rapidly, and there is absolutely a case to reach characteristic deterioration and destruction of a device. In particular in a serge examination of a set, when it is expected the impressing serge at VCC terminal (14,24pin), please do not impress the large and over the absolute maximum rating voltage (including a operating voltage + serge ingredient (around 14V)) 2.About a signal input part 1)In the signal input terminal, the constant setting of input coupling capacitor C(F) be sufficient input impedance RIN(Ω) inside IC and please decide. The first HPF characteristic of RC is composed. G[dB] C[F] 0 RIN [Ω] A(f) SSH F[Hz] INPUT A(f) = (2πfCRIN) 2 1 + (2πfCRIN) 2 2) SHORT mode is the command which makes switch SSH =ON an input selector part and input impedance RIN of all terminals, and makes resistance small. Switch SSH is OFF when not choosing a SHORT command. A constant time becomes small at the time of this command twisting to the resistance inside the capacitor connected outside and LSI. The charge time of a capacitor becomes short. Since SHORT mode turns ON the switch of SSH and makes it low impedance, please use it at the time of a non-signal. 3.About Mute terminal(15pin) when power supply is off Any voltage shall not be supplied to Mute terminal (15pin) when power-supply is off. Please insert a resistor (about 2.2kΩ) to Mute terminal in series, if voltage is supplied to mute terminal in case. (Please refer Application Circuit Diagram.) 4. About Hi-Voltage function About Logic of Hi-Voltage function is follow as. Hi-Voltage ON/OFF Hivoltage ON/OFF(Select Address 01hex, D2) Level Shift(Select Address 01hex, D3) Level of amplification in the output-unit Bias-voltage in the output-unit 0 0 0 4.15 0 1 3 4.15 1 0 6 6 1 1 6 6 [dB] [V] Hi-Voltage ON ・Though the level of amplification in the output-unit is controlled with Level Shift (Select Address 01hex, D3), it becomes a +6dB fixation under the condition of Hi-Voltage function is ON. ・Under the condition of Hi-Voltage function is OFF, 0dB/+3dB switching is possible by the setup of Level Shift. ・Under the condition of Hi-Voltage function is OFF, bias-voltage is 4.15V regardless of the setup of Level Shift. ・The use of the external MUTE on the set side is recommended because shock noise by the DC step is made when ON/OFF switching of the Hi-Voltage function is done. ・The initial condition of Hi-Voltage function is Hi-Voltage=ON after a power supply is started) www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・ 15・ 001 42/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M Ordering Information B D 3 7 0 4 3 F V ME 2 Package FV: SSOP-B28 Part Number Packaging and forming specification E2: Embossed tape and reel (SSOP-B28) Physical Dimension Tape and Reel Information SSOP-B28 Tape Embossed carrier tape 28 Quantity 2000pcs 15 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand 0.3Min. 1 ) 14 0.15 ± 0.1 0.1 1.15 ± 0.1 E2 Direction of feed 5.6 ± 0.2 7.6 ± 0.3 10 ± 0.2 (MAX 10.35 include BURR) 0.1 0.65 0.22 ± 0.1 1pin Reel (Unit : mm) ∗ Direction of feed Order quantity needs to be multiple of the minimum quantity. Marking Diagram(s)(TOP VIEW) SSOP-B28(TOP VIEW) Part Number Marking BD37034FV LOT Number 1PIN MARK www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・ 15・ 001 43/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet BD37034FV-M Revision history Date Revision 3.APR.2013 001 Date Revision 4.OCT.2013 002 4.OCT.2013 002 4.OCT.2013 002 4.OCT.2013 002 Changes New Release Changes All page ● delete Page 2 < Sub Title> Sound Processors for Car Audios ⇒ Analog Audio Processors series change. AEC-Q100 Qualified add. PbFree, RoHS delete Page 3 Power Dissipation mW ⇒ W change. Page 43 Ordering Information, E2 ⇒ ME2 change. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・ 15・ 001 44/44 TSZ02201-0C2C0E100010-1-2 4.OCT.2013 Rev.002 Datasheet Notice Precaution on using ROHM Products 1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅢ CLASSⅣ CLASSⅢ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice - SS © 2014 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act, please consult with ROHM representative in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable for infringement of any intellectual property rights or other damages arising from use of such information or data.: 2. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the information contained in this document. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice - SS © 2014 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s representative. 3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. Notice – WE © 2014 ROHM Co., Ltd. All rights reserved. Rev.001