BD6047AGUL-E2

Datasheet Charge protection ICs with Built-in FET Negative Voltage Protection type BD6047AGUL ●General Description BD6047AGUL protects the devices from the abnormal input voltage at the USB port. Addition to the conventinal charge protection IC, it prevents the negative voltage happened by the USB reverse insertion without any additional compornents. ROHM's original charge protection IC series enables to protect the abnormal input voltage from -30V to +30V. ●Key Specifications  Input voltage range:  Voltage Protection range:  Internal Low Ron:  Start Up Delay:  Operating temperature range: W(Typ.) ●Package 2.2V to 28V ±30V 125mΩ(Typ.) 6.0msec(Typ.) -40℃ to +85℃ D(Typ.) H (Max.) ●Features  Over Voltage Protection up to 30V  Negative Voltage Protection down to -30V  Over voltage Lockout (OVLO)  Under voltage Lockout (UVLO)  Over Current Protect  Thermal Shut Down ●Applications Mobile phones, MP3 players, Digital Still Camera, PDA, IC recorder, Electronic Dictionary, Handheld Game, Game Controller, Camcorder, Bluetooth Headsets, etc VCSP50L1 1.95mm x 1.95mm x 0.55mm ●Typical Application Circuit OVP CPU FLGB IN 28V-OVP Cin 1.0uF Travel Adapter GND OUT PMIC Cout 0.47uF CHGIN Charger BATT Li-ion 1cell ・Safety is high because it detects, and it protects it for an abnormal voltage up to ±30V. ・It contributes to the miniaturization because all external is built into. ○Product structure : Silicon monolithic integrated circuit www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･14･001 ○This product is not designed protection against radio active rays. 1/15 TSZ02201-0B1B0AB00090-1-2 21. May.2013 Rev.001 Datasheet BD6047AGUL ●Block Diagram Travel Adapter OUT CHARGE IN IN IN IN IN OUT OUT NVP FLGB Initial Delay VREF UVLO Gate Driver OVLO OCP TSD Timing Generator Initial Delay OSC GND ●Pin Configuration ●Pin Description PIN NAME FUNCTION A1, A2, A3 B1, B2 IN C1, C2 OUT Output Voltage Pin C3 FLGB Open-drain output pin that turns low when any protection event occurs. (overvoltage protection, thermal shut down) B3 GND Ground Pin www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 Input voltage Pin. A 1µF low ESR capacitor, or larger must be connected between this pin and GND 2/15 TSZ02201-0B1B0AB00090-1-2 21. May.2013 Rev.001 Datasheet BD6047AGUL ●Absolute Maximum Ratings (Ta=25℃) Contents Symbol Rating Unit Conditions Input supply voltage 1 Vmax1 -30 to 30 V IN Input supply voltage 2 Vmax2 -0.3 to 7 V other Pd 900 mW Operating temperature range Topr -40 to +85 ℃ Storage temperature range Tstr -55 to +150 ℃ Power dissipation ※1 When using more than at Ta=25℃, it is reduced 7.2mW per 1℃. ROHM specification board 50mm× 58mm mounting. ●Recommended Operating Ratings (Ta = -40℃ to +85℃) Parameter Input voltage range Symbol Range Unit Vin 2.2 to 28 V ●Electrical Characteristics (Unless otherwise noted, Ta = 25C, IN=5V) Parameter Limit Symbol Unit Min. Typ. Max. Conditions ●ELECTRICAL Input Voltage Range VIN - - 28 V Supply Quiescent Current ICC - 40 80 µA Under Voltage Lockout UVLO 3.42 3.6 3.78 V IN=decreasing Under Voltage Lockout Hysteresis UVLOh 50 100 150 mV IN=increasing Over Voltage Lockout OVLO 5.7 5.85 6.0 V IN=increasing Over Voltage OVLOh 50 100 150 mV IN=decreasing Current limit ILM 1.7 - - A Vin vs. Vout Res. RON - 125 150 mΩ FLGB Output Low Voltage FLGBVO - - 400 mV FLGB Leakage Current FLGBleak - - 1 µA OUT pin input Current OUTIIN - - 1 mA Start Up Delay Ton - 6 10 msec Output Turn Off Time Toff - 2 10 µsec Alert Delay Tovp - 1.5 10 µsec Lockout Hysteresis SINK=1mA IN=3V(UVLO), OUT=3V ●TIMINGS www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 3/15 TSZ02201-0B1B0AB00090-1-2 21. May.2013 Rev.001 Datasheet BD6047AGUL ●Typical Performance Curves ※The test conditions for the Typical Operating Characteristics are IN=5V、CIN=1µF、COUT=0.47µF、Ta=25℃, Unless otherwise noted. IN(5V/div) high high IN(20V/div) OUT(2V/div) OUT(5V/div) FLGB(5V/div) FLGB(5V/div) Figure 1. Start up (0→5V) Figure 2. Input Steps (0→-30V) IN(20V/div) IN(20V/div) Maximum Maximum OUT(2V/div) OUT(5V/div) FLGB(5V/div) FLGB(5V/div) Figure 3. Input Steps （0→30V） www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 Figure 4. Input Steps （5→30V） 4/15 TSZ02201-0B1B0AB00090-1-2 21. May.2013 Rev.001 Datasheet BD6047AGUL ●Typical Performance Curves - continued IN(20V/div) high OUT(5V/div) FLGB(5V/div) Figure 5. Input Steps （30→5V） IN(5V/div) high high IN(5V/div) Io(2A/div) Io(2A/div) OUT(5V/div) OUT(5V/div) FLGB(5V/div) FLGB(5V/div) Figure 6. Output Short Circuit www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 Figure 7. Output Short Circuit (Zoom) 5/15 TSZ02201-0B1B0AB00090-1-2 21. May.2013 Rev.001 Datasheet BD6047AGUL ●Typical Performance Curves - continued 0 2.5 -10 2.0 A ICC[mA] IC C ( m ICC[uA] IC C ( u A -20 -30 -40 1.5 1.0 0.5 -50 0.0 -60 -30 -20 -10 0 0 5 10 15 20 25 30 IN[V] IN[V] IN(V) IN(V) Figure 9. ICC vs Input Voltage (0-30V) Figure 8. ICC vs Input Voltage (-30-0V) 100 140 80 120 IC C (u A 80 ICC[uA] IC C (u A ICC[uA] 100 60 40 60 40 20 20 0 -100 0 0 2 4 IN[V] IN(V) 6 0 50 100 150 Temp[℃] 温度(℃) Figure 10. ICC vs Input Voltage （0-7V） www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 -50 Figure 11. ICC vs Temperature (IN=5V) 6/15 TSZ02201-0B1B0AB00090-1-2 21. May.2013 Rev.001 Datasheet BD6047AGUL ●Typical Performance Curves - continued 7 150 6 140 OVLO RRon[mΩ] on[m Ω ] Voltage[V] 電 圧 (V ) 5 130 4 3 120 UVLO 2 110 1 100 0 -50 0 50 100 150 Temp[℃] 3.5 4.0 4.5 5.0 5.5 IN[V] IN[V] 温度(℃) Figure 13. RON vs Input Voltage Figure 12. UVLO/OVLO vs Temperature 200 Ron[m Ω ] 180 Ron[mΩ] 160 140 120 100 80 -60 -40 -20 0 20 40 60 80 100 120 140 Temp[℃] Temp[℃] Figure 14. RON vs Temperature （IN=5V） www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 7/15 TSZ02201-0B1B0AB00090-1-2 21. May.2013 Rev.001 Datasheet BD6047AGUL ●Timing Diagram OVLO UVLO IN 6.0msec OUT (Ton) FLGB Figure 15. Start up sequence OVLO IN UVLO 2.0μ sec OUT (Toff) 1.5 μ sec FLGB (Tovp) Figure 16. Shutdown by over voltage detection 15V IN 5V 6.0msec OUT 1μ sec FLGB Figure 17. Recovery from overvoltage protection . www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 8/15 TSZ02201-0B1B0AB00090-1-2 21. May.2013 Rev.001 Datasheet BD6047AGUL ●Examples of Application Circuit (Ball Configuration is Bottom View) A: In case of FLGB pins are connected. Adapter / USB IN PMIC / charger OUT 1.0uF Li-ion 1 cell 0.47uF BD6047 100kΩ FLGB CPU ※ to limit current of negative voltage. GND C OUT ※ 負電圧印加時の 電流制限 ※として挿入して下 Please insert さいthe resister OUT FLGB B IN IN GND A IN IN IN 1 2 3 B: In case of FLGB pins are not connected. Adapter / USB IN PMIC / charger OUT 1.0uF 0.4 7uF BD6047 Li-ion 1 cell FLGB GND C OUT B A OUT FLGB IN IN GND IN IN IN 1 2 3 OPEN www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 C OUT B A OUT FLGB IN IN GND IN IN IN 1 2 3 GND SHORT or 9/15 TSZ02201-0B1B0AB00090-1-2 21. May.2013 Rev.001 Datasheet BD6047AGUL ●BD6047 Evaluation Board Power Supply （ Adapter) 充電IC Charger IC C1: 1.0uF(50V) U1 IN OUT C2 C2: 0.4 7μF C1 C3 GND R1 FLGB DVDD FLGB: OVLO=L UVLO/ NORMAL=H DVDD: FLGB Pin Pull-Up Power Supply R1: 100kΩ Charger IC www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 10/15 TSZ02201-0B1B0AB00090-1-2 21. May.2013 Rev.001 Datasheet BD6047AGUL ●Power dissipation Power dissipation : Pd(W) 1.5 1 Pd=0.90W -7.2mW/℃ 0.5 Ta_MAX=85℃ 0 0 25 50 75 100 125 150 Ta (℃) ※ On the ROHM’s specification Board ●I/O equivalence circuit www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 11/15 TSZ02201-0B1B0AB00090-1-2 21. May.2013 Rev.001 Datasheet BD6047AGUL ●Operational Notes (1) Absolute maximum ratings If applied voltage (VDD, VIN), operating temperature range (Topr), or other absolute maximum ratings are exceeded, there is a risk of damage. Since it is not possible to identify short, open, or other damage modes, if special modes in which absolute maximum ratings are exceeded are assumed, consider applying fuses or other physical safety measures. (2) Recommended operating range This is the range within which it is possible to obtain roughly the expected characteristics. For electrical characteristics, it is those that are guaranteed under the conditions for each parameter. Even when these are within the recommended operating range, voltage and temperature characteristics are indicated. (3) Power supply lines In the design of the board pattern, make power supply and GND line wiring low impedance. When doing so, although the digital power supply and analog power supply are the same potential, separate the digital power supply pattern and analog power supply pattern to deter digital noise from entering the analog power supply due to the common impedance of the wiring patterns. Similarly take pattern design into account for GND lines as well. Furthermore, for all power supply pins of the LSI, in conjunction with inserting capacitors between power supply and GND pins, when using electrolytic capacitors, determine constants upon adequately confirming that capacitance loss occurring at low temperatures is not a problem for various characteristics of the capacitors used. (4) GND voltage Make the potential of a GND pin such that it will be the lowest potential even if operating below that. In addition, confirm that there are no pins for which the potential becomes less than a GND by actually including transition phenomena. (5) Shorts between pins and misinstallation When installing in the set board, pay adequate attention to orientation and placement discrepancies of the LSI. If it is installed erroneously, there is a risk of LSI damage. There also is a risk of damage if it is shorted by a foreign substance getting between pins or between a pin and a power supply or GND. (6) Operation in strong magnetic fields Be careful when using the LSI in a strong magnetic field, since it may malfunction. (7) Inspection in set board When inspecting the LSI in the set board, since there is a risk of stress to the LSI when capacitors are connected to low impedance LSI pins, be sure to discharge for each process. Moreover, when getting it on and off of a jig in the inspection process, always connect it after turning off the power supply, perform the inspection, and remove it after turning off the power supply. Furthermore, as countermeasures against static electricity, use grounding in the assembly process and take appropriate care in transport and storage. (8) Input pins Parasitic elements inevitably are formed on an LSI structure due to potential relationships. Because parasitic elements operate, they give rise to interference with circuit operation and may be the cause of malfunctions as well as damage. Accordingly, take care not to apply a lower voltage than GND to an input pin or use the LSI in other ways such that parasitic elements operate. Moreover, do not apply a voltage to an input pin when the power supply voltage is not being applied to the LSI. Furthermore, when the power supply voltage is being applied, make each input pin a voltage less than the power supply voltage as well as within the guaranteed values of electrical characteristics. (9) Ground wiring pattern When there is a small signal GND and a large current GND, it is recommended that you separate the large current GND pattern and small signal GND pattern and provide single point grounding at the reference point of the set so that voltage variation due to resistance components of the pattern wiring and large currents do not cause the small signal GND voltage to change. Take care that the GND wiring pattern of externally attached components also does not change. (10) Externally attached capacitors When using ceramic capacitors for externally attached capacitors, determine constants upon taking into account a lowering of the rated capacitance due to DC bias and capacitance change due to factors such as temperature. (11) Thermal shutdown circuit (TSD) When the junction temperature reaches the defined value, the thermal shutdown circuit operates and turns a switch OFF. The thermal shutdown circuit, which is aimed at isolating the LSI from thermal runaway as much as possible, is not aimed at the protection or guarantee of the LSI. Therefore, do not continuously use the LSI with this circuit operating or use the LSI assuming its operation. (12) Thermal design Perform thermal design in which there are adequate margins by taking into account the permissible dissipation (Pd) in actual states of use. Status of this document The Japanese version of this document is formal specification. A customer may use this translation version only for a reference to help reading the formal version. If there are any differences in translation version of this document formal version takes priority. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 12/15 TSZ02201-0B1B0AB00090-1-2 21. May.2013 Rev.001 Datasheet BD6047AGUL ●Ordering Information B D 6 0 4 7 A Part Number G U L Package GUL : VCSP50L1 - E2 Packaging and forming specification E2: Embossed tape and reel ●Marking Diagram VCSP50L1 (TOP VIEW) 1PIN MARK Part Number Marking 0 4 7 A www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 LOT Number 13/15 TSZ02201-0B1B0AB00090-1-2 21. May.2013 Rev.001 Datasheet BD6047AGUL ●Physical Dimension Tape and Reel Information Package Name VCSP50L1 Lot No. 1.95±0.05 1PIN MARK 6047A 047 0.1±0.05 0.55MAX 1.95±0.05 S 9-φ0.25±0.05 A 0.05 A B (φ0.15)INDEX POST C B B A 1 0.475±0.05 www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 2 P=0.5×2 0.475±0.05 0.06 S 3 P=0.5×2 14/15 TSZ02201-0B1B0AB00090-1-2 21. May.2013 Rev.001 Datasheet BD6047AGUL ●Revision History Date Revision 21.May.2013 001 Changes New Release www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 15/15 TSZ02201-0B1B0AB00090-1-2 21. May.2013 Rev.001 Notice Precaution on using ROHM Products 1. Our Products are designed and manufactured for application in ordinary electronic equipment (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), transport equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅢ CLASSⅣ CLASSⅢ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (Exclude cases where no-clean type fluxes is used. However, recommend sufficiently about the residue.) ; or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in the range that does not exceed the maximum junction temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice-PGA-E © 2015 ROHM Co., Ltd. All rights reserved. Rev.004 Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl 2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign trade act, please consult with ROHM in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the Products with other articles such as components, circuits, systems or external equipment (including software). 3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the Products, subject to the terms and conditions herein. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice-PGA-E © 2015 ROHM Co., Ltd. All rights reserved. Rev.004 Datasheet General Precaution 1. Before you use our Products, you are requested to carefully read this document and fully understand its contents. ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of any ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this document is current as of the issuing date and subject to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sales representative. 3. The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccuracy or errors of or concerning such information. Notice – WE © 2015 ROHM Co., Ltd. All rights reserved. Rev.001