0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
BD6586MUV_11

BD6586MUV_11

  • 厂商:

    ROHM(罗姆)

  • 封装:

  • 描述:

    BD6586MUV_11 - White Backlight LED Driver for Medium to Large LCD Panels (Switching Regulator Type) ...

  • 数据手册
  • 价格&库存
BD6586MUV_11 数据手册
LED Drivers for LCD Backlights White Backlight LED Driver for Medium to Large LCD Panels (Switching Regulator Type) BD6586MUV No.11040ECT35 ●Description BD6586MUV is white LED driver IC with PWM step-up DC/DC converter that can boost max 24V and current driver that can drive max 25mA. The wide and precision brightness can be controlled by external PWM pulse. BD6586MUV has very accurate current drivers, and it has few current errors between each strings.So, it will be helpful to reduce brightness spots on the LCD.Small package type is suited for saving space. ●Features 1) High efficiency PWM step-up DC/DC converter (fsw=1MHz) 2) High accuracy & good matching (±3.0%) current drivers 4ch (MAX.25mA/ch) 3) 28V power Nch MOSFET 4) Soft Start 5) Drive up to 6 in series, 4 strings in parallel 6) Rich safety functions ▪ Over-voltage protection ▪ Output Short protection ▪ External SBD open detect ▪ Over current limit ▪ Thermal shutdown ▪ UVLO 7) Small & thin package (VQFN024V4040) 4.0 × 4.0 × 1.0mm ●Applications All middle size LCD equipments backlight of Notebook PC, portable DVD player, car navigation systems, etc. ●Absolute maximum ratings (Ta=25 ℃) Parameter Maximum applied voltage 1 Maximum applied voltage 2 Maximum applied voltage 3 Maximum applied voltage 4 Power dissipation 1 Power dissipation 2 Power dissipation 3 Operating temperature range Storage temperature range *1 *2 *3 Symbol VMAX1 VMAX2 VMAX3 VMAX4 Pd1 Pd2 Pd3 Topr Tstg Ratings 7 25 30.5 50.5 500 *1 780 *2 1510 *3 -40 ~ +85 -55 ~ +150 Unit V V V V mW mW mW ℃ ℃ Condition VBAT, EN1, EN2, TRSW, PWM,TESTO, ISET, TEST LED1, LED2, LED3, LED4, SW VDET Reduced 4.0mW/ ℃ With Ta>25 ℃ when not mounted on a heat radiation Board. 1 layer (ROHM Standard board) has been mounted. Copper foil area 0mm2, When it’s used by more than Ta=25 ℃, it’s reduced by 6.2mW/ ℃. 4 layer (JEDEC Compliant board) has been mounted. Copper foil area 1layer 6.28mm2, Copper foil area 2~4layers 5655.04mm2, When it’s used by more than Ta=25 ℃, it’s reduced by 12.1mW/ ℃. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 1/19 2011.6 - Rev.C BD6586MUV ●Recommended operating range (Ta=-40 ℃ ~ +85 ℃) Parameter Power supply voltage Symbol VBAT Ratings Min. 2.7 Typ. 3.6 Max. 5.5 Unit V Technical Note Condition ●Electrical characteristic (Unless otherwise specified, VBAT=3.6V, Ta = +25 ℃) Limits Parameter Symbol Unit Min. Typ. Max. [EN1, EN2, PWM Terminal] EN threshold voltage (Low) EN threshold voltage (High) EN terminal input current [Under Voltage Lock Out] Under Voltage Lock Out [Switching Regulator] Quiescent Current Current Consumption LED Control voltage Over Current Limit SBD Open Protect Switching frequency Duty cycle limit Over voltage limit SW Transistor On Resistance [Current driver] LED maximum current LED current accuracy LED current matching ISET voltage LED current limiter LED Terminal Over Voltage Protect ILMAX ILACCU ILMAT Iset ILOCP LEDOVP 0.5 35 10.0 0.6 60 11.5 25 ±5 ±3 0.7 90 13.0 mA % % V mA V ILED=20mA Iq Idd VLED Ocp Sop fSW Duty Ovl RSW 0.4 1.1 0.7 91 25.0 0.1 2.2 0.5 1.5 1.0 95 25.5 0.24 2.0 4.6 0.6 2.5 0.1 1.3 99 26.0 0.32 µA mA V A V MHz % V Ω LED1-4=0.3V LED1-4=0.3V Isw=100mA *1 Condition VthL VthH Iin 0 1.4 - 8.3 0.4 5.5 16.0 V V µA Input=2.5V UVLO 2.05 2.35 2.65 V VBAT falling edge EN1=EN2=PWM=0V VDET=0V,ISET=24kΩ Detect voltage of VDET pin ▪Each LED current/Average (LED1- 4) ▪ILED=20mA Current limit value at ISET resistance 4.7kΩ setting LED1, 2, 3, 4=0.5V EN1=EN2=PWM=2.5V *1 This parameter is tested with DC measurement. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 2/19 2011.6 - Rev.C BD6586MUV ●Block diagram, I/O equivalent circuit diagram VBAT EN1 EN2 SBD OPEN/ Output short PROTECT TSD UVLO Output Over Voltage PROTECT VBAT TRSW SW SW SW Pulse Control Soft start PWM COMP + LED TERMINAL OPEN/SHORT DETECTOR + Reference Technical Note VDET VBAT VBAT PIN PIN PIN GND A VBAT LED1 LED RETURN SELECT LED2 LED3 LED4 OSC Current SENCE 4ch P GND B GND C ERRAMP + PIN PIN PIN GND D E PGND F + PGND PGND ISET Resistor driver + - PIN GND PGND Current Driver G GND N.C. GND TEST TESTO N.C. PWM ISET GND Fig.1 Block diagram Fig.2 I/O equivalent circuit diagram ●Pin assignment table PIN Name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 In/Out VBAT EN1 EN2 GND PWM ISET GND LED1 LED2 GND LED3 LED4 TEST TESTO N.C. SW SW SW VDET N.C. PGND PGND N.C. TRSW PIN number In In In In In In In In In In Out Out Out Out In Out Battery input Power control pin Power control pin GND for DC/DC PWM input pin for power ON/OFF only driver Register connection for LED current setting GND for ISET Register Current sink for LED1 Current sink for LED2 GND for Current Driver Current sink for LED3 Current sink for LED4 TEST input (Pull down 100kΩ to GND) TEST output No connect pin Switching Tr drive Pin Switching Tr drive Pin Switching Tr drive Pin Detect input for SBD open and OVP No connect pin PGND for switching transistor PGND for switching transistor No connect pin The gate of Switching Tr Function Terminal equivalent circuit diagram G A A B A D B C C B C C A D E F F F C E D D E D www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 3/19 2011.6 - Rev.C BD6586MUV Technical Note ●Description of Functions 1) PWM current mode DC/DC converter While BD6586MUV is power ON, the lowest voltage of LED1, 2, 3, 4 is detected, PWM duty is decided to be 0.5V and output voltage is kept invariably. As for the inputs of the PWM comparator as the feature of the PWM current mode, one is overlapped with error components from the error amplifier, and the other is overlapped with a current sense signal that controls the inductor current into Slope waveform to prevent sub harmonic oscillation. This output controls internal Nch Tr via the RS latch. In the period where internal Nch Tr gate is ON, energy is accumulated in the external inductor, and in the period where internal Nch Tr gate is OFF, energy is transferred to the output capacitor via external SBD. BD6586MUV has many safety functions, and their detection signals stop switching operation at once. 2) Soft start BD6586MUV has soft start function. The soft start function prevents large coil current. Rush current at turning on is prevented by the soft start function. After EN1, EN2 are changed L H, soft start becomes effective for within 1ms and soft start doesn't become effective even if EN1, EN2 are changed L H after that. And, when the H section of PWM is within 1ms, soft start becomes invalid when PWM is input to H more than three times. The invalid of the soft start can be canceled by making EN1, EN2, PWM  L. And, a soft start function doesn't work after a protection function release. 3) External SBD open detect and over voltage protection BD6586MUV has over boost protection by external SBD open and over voltage protection. It detects VDET voltage and is stopped output Tr in abnormal condition. Details are as shown below. ▪ External SBD open detect In the case of external SBD is not connected to IC, the coil or internal Tr may be destructed. Therefore, at such an error as VOUT becoming 0.1V or below, the Under Detector shown in the figure works, and turns off the output Tr, and prevents the coil and the IC from being destructed. And the IC changes from activation into non-activation, and current does not flow to the coil (0mA). ▪ Over voltage protection At such an error of output open as the output DC/DC and the LED is not connected to IC, the DC/DC will boost too much and the VDET terminal exceed the absolute maximum ratings, and may destruct the IC. Therefore, when VDET becomes sensing voltage or higher, the over voltage limit works, and turns off the output Tr, and the pressure up made stop. At this moment, the IC changes from activation into non-activation, and the output voltage goes down slowly. And, when the output voltage becomes the hysteresis of the over voltage limit or below, the output voltage pressure up to sensing voltage once again and unless the application error is recovered, this operation is repeated. 4) Thermal shut down BD6586MUV has thermal shut down function. The thermal shut down works at 175C or higher, and while holding the setting of EN1, EN2 control from the outside, turns into non operation condition from operation condition. And at 175C or below, the IC gets back to its normal operation. 5) Over Current Limit Over current flows the current detection resistor between switching transistor source and PGND, then the voltage of that resistor turns more than detection voltage. Over current protection is operating and it is prevented from flowing more than detection current by reducing ON duty of switching Tr without stopping boost. As over current detector of BD6586MUV is detected peak current, current more than over current setting value does not flow. 6) Under Voltage Lock Out(UVLO) When VBAT declines in 2.35V (Typ.) from the condition of the power-on, DC/DC and a current driver are changed from a state of movement to the condition at the time of the non-movement. And, it is returned in a state of movement when VBAT is raised beyond 2.55V (Typ.). www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 4/19 2011.6 - Rev.C BD6586MUV Technical Note ●Operating of the application deficiency 1) When 1 LED or 1parallel OPEN during the operating the LED parallel which became OPEN isn't lighting, but other LED parallel is lighting. Then, Output boosts up to the over voltage protection voltage 25.5V because LED terminal can be 0V. After the over voltage protection is detected, LED terminal of 0V isn’t cut from feedback loop. Then, Output voltage will become normal voltage automatically. 2) When LED short-circuited in the plural All LED continue to be turned on, unless LED terminal voltage become more than “LED terminal over voltage protection (11.5V)”. When it was more than 11.5V, the line which short-circuited is only turned on, and LED current of other lines decrease or turn off. 3) When Schottky diode came off All LED aren't turned on. Also, IC isn't destroyed because boost operating stops by the Schottky diode coming off protected function. 4) When an output capacitor short. All LED aren't turned on. And, an IC isn't destroyed because boost stops by the SBD open protection function. But, big electric current occurs, and a coil or SBD is likely to destroy it because the route of the GND short circuit of the power supply → coil → output capacitor occurs. 5) When the resistance to connect it to the ISET terminal short. All LED aren't turned on. Because LED current limit works, all current drivers stop, and DC/DC maintains boost under the state without load. And, it is returned in a state of normality by canceling a state of short. ●Start control and select constant current driver BD6586MUV can control the start conditions by EN1, 2 and PWM terminals, and sets 0.4V or below EN1, 2 terminals, so IC can power off. EN1,2 and PWM power on at more than 1.4V, constant current can select ON/OFF by the combination of EN as shown below table. When there is unused constant current driver, unused LED terminal is set “OPEN”. Enable EN1 H L H L H L H L EN2 H H L L H H L L PWM H H H H L L L L LED1 OFF OFF ON OFF OFF OFF OFF OFF Constant current driver LED2 ON ON ON OFF OFF OFF OFF OFF LED3 ON ON ON OFF OFF OFF OFF OFF LED4 OFF ON ON OFF OFF OFF OFF OFF IC POWER ON ON ON OFF ON ON ON OFF www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 5/19 2011.6 - Rev.C BD6586MUV ●Control Signal input timing HI Voltage of PWM, EN 2.7V Stable voltage VBAT PWM EN1,2 DC/DC VOUT Fig.3 control Signal timing 1 ○ 2 ○ 3 ○ Min. 100µs HI Voltage of PWM Technical Note 0V VBAT 10kΩ 5V PIN 300kΩ GND Fig.4 Voltage with a control sign higher than VBAT Example corresponding to application of conditions In case you input control signs, such as EN1, EN2 and PWM in the condition that the standup of supply voltage (VBAT) is not completed, be careful of the following point. ①Input each control signal after VBAT exceeds 2.7V. ②Please do not input each control sign until VBAT exceeds HI voltage of EN1, EN2 and PWM. ③When you input HI voltage to EN1, EN2 and PWM during the standup of VBAT, please give Min.100µs as the standup time of VBAT from stable voltage to 2.7V. There is no timing limitation at each input signal of EN1, EN2 and PWM. If each control sign changes into a condition lower than VBAT in (1) and (2), it goes via the ESD custody diode by the side of VBAT of each terminal. A power supply is supplied to VBAT and there is a possibility of malfunctioning. Moreover, when the entrance current to the terminal exceeds 50mA, it has possibility to damage the LSI. In order to avoid this condition, as shown in the above figure, please insert about 10kΩ in a signal line, and apply current qualification. ●LED current setting range LED current can set up Normal current by resistance value (RISET) connecting to ISET voltage. Setting of each LED current is given as shown below. Normal current = 20mA(24kΩ/RISET) Also, Normal current setting range is 10mA~25mA. LED current becomes a leak current MAX 2µA at OFF setting. ISET Normal current setting example RISETH LED current 24kΩ (E24) 20mA 25.5 kΩ (E96) 18.8mA 27 kΩ (E12) 17.8mA 28kΩ (E96) 17.1mA 30kΩ (E24) 16.0mA 33kΩ (E6) 14.5mA www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 6/19 2011.6 - Rev.C BD6586MUV Technical Note ●Brightness control There are two dimming method is available, first method is analog dimming that apply analog voltage to ISETH terminal, and second method is PWM control via digital dimming of EN1, EN2 PWM terminals or PWM. Because each method has the different merit, please choose a suitable method for the application of use. Refer to Fig.23 for the analog dimming. Two techniques can be used as digital dimming by the PWM control. One is PWM control of current driver, the other is PWM control of power control. As these two characteristics are shown in the below, selects to PWM control process comply with application. •Efficiency emphasis in the low brightness which has an influence with the battery life •LED current dispersion emphasis in the PWM brightness control (Reference) PWM regulation process Current driver Power control Efficiency of LED current 0.2mA (PWM Duty=1%) 60% 94% PWM frequency 200Hz Low Duty 0.1% 0.6%  2) Power control PWM control  1) Current driver PWM control 1) Current driver PWM control is controlled by providing PWM signal to PWM terminal, as it is shown Fig.5. The current set up with ISET is chosen as the H section of PWM and the current is off as the L section. Therefore, the average LED current is increasing in proportion to duty cycle of PWM signal. This method that it lets internal circuit and DC/DC to work, because it becomes to switch the driver, the current tolerance is a few when the PWM brightness is adjusted, it makes it possible to brightness control until 20µs (MIN0.4% at 200Hz). And, don't use for the brightness control, because effect of ISET changeover is big under 20µs ON time and under 20µs OFF time. There is no effect of ON/OFF changeover at 0% and 100%, so there is no problem on use. Typical PWM frequency is 100Hz~10kHz. PWM LED current Coil current IC’s active current ON ON ON OFF OFF OFF ON Fig.5 Current driver PWM control 2) Power control PWM control is controlled by providing PWM signal to EN1, EN2 as it is shown Fig.6. The current setting set up with PWM logic is chosen as the H section and the current is off as the L section. Therefore, the average LED current is increasing in proportion to duty cycle of EN1, EN2 signal. This method is, because IC can be power-off at off-time, the consumption current can be suppress, and the high efficiency can be available, so it makes it possible to brightness control until 50µs (MIN1% at 200Hz). And, don't use for the brightness control, because effect of power ON/OFF time changeover is big under 50µs ON time and under 50µs OFF time. There is no effect of ON/OFF changeover at 0% and 100%, so there is no problem on use. Typical PWM frequency is 100Hz~1kHz. EN1,EN” LED current Coil current IC’s active current ON ON ON ON OFF OFF OFF OFF Fig.6 Power control PWM control www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 7/19 2011.6 - Rev.C BD6586MUV Technical Note ●The separations of the IC Power supply and coil Power supply This IC can work in separating the power source in both IC power supply and coil power supply. With this application, it can obtain that decrease of IC power consumption, and the applied voltage exceeds IC rating 5.5V. That application is shown in below Fig.7. The higher voltage source is applied to the power source of coil that is connected from an adapter etc. Next, the IC power supply is connected with a different coil power supply. When the coil power supply is applied, it is no any problem even though IC power supply is the state of 0V. Although IC power supply is set to 0V, pull-down resistance is arranged for the power off which cuts off the leak route from coil power supply in IC inside, the leak route is cut off. And, there is no power on-off sequence of coil power supply and IC power supply. Other Power Supply 6V to 25V Battery 2.7V to 5.5V 4.7μF 4.7μH 2.2μF 6LED x 4Parallel SW TRSW EN2 Power ON/OFF EN1 SW SW VBAT VDET LED1 LED2 PWM TESTO TEST PGND PGND GND GND GND ISET LED3 LED4 Each 20mA 24kΩ Fig.7 Each battery and coil power supply ●The coil selection The DC/DC is designed by more than 4.7µH. When L value sets to a lower value, it is possibility that the specific sub-harmonic oscillation of current mode DC / DC will be happened. Please do not let L value to 3.3µH or below. And, L value increases, the phase margin of DC / DC becomes to zero. Please enlarge the output capacitor value when you increase L value. Example) 4.7µH = output capacitor 2.2µF/50V 1pcs 6.8µH = output capacitor 2.2µF/50V 2pcs 10µH = output capacitor 2.2µF/50V 3pcs This value is just examples, please made sure the final judgment is under an enough evaluation. ●The adjustment of the switching wave form A switching wave form between the coil and the switch terminal can be adjusted by connecting a capacitor to TRSW. Switching noise can be restrained though efficiency is made to decrease by connecting a capacitor. Decide capacity value after the enough evaluation when you adjust switching noise. SW SW TRSW PGND TRSW PGND Fig.8 The adjustment of the switching wave form www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 8/19 2011.6 - Rev.C BD6586MUV Technical Note ●PCB Layout In order to make the most of the performance of this IC, its layout pattern is very important. Characteristics such as efficiency and ripple and the likes change greatly with layout patterns, which please note carefully. to Power Supply to Power Suppl y to GND CIN L SBD COUT to Anode of LED TRSW PGND 23 22 1 PGND 24 21 20 19 VDET 18 N.C. VBAT PWM (100Hz~1000Hz) 2 N.C. SW Thermal Via 17 EN1 3 SW 16 CVBAT EN2 LE D 6 BD6586MUV LE D2 SW 15 4 LE D5 LED 4 LED 3 GND T hermal Via N.C. 14 RISET PWM 6 5 TEST0 13 ISET LED1 LED3 LED2 7 8 9 10 11 12 TEST LED4 GND GND to Anode of each LED Fig.9 PCB Layout Connect the input bypath capacitor CIN nearest to coil L and PGND, as shown in the upper diagram. Ripple of a power supply is smoothed by CIN and connect stable voltage to VBAT terminal by the low resistance. Thereby, the input voltage ripple of the IC can be reduced. Connect CVBAT nearest to between the VBAT terminal and GND (4 pin) as shown in the upper diagram when you can't be wired by the low resistance from CIN to VBAT pin Connect schottky barrier diode SBD of the regulator nearest to between coil L and SW terminal. And connect output capacitor COUT nearest to between CIN and GND pin. Thereby, the output voltage ripple of the IC can be reduced. GND terminal (4,7,10 pin) is connected inside the IC, and it is GND of the block except switching and a transistor. A current drive performance may be restricted by influence of a noise, if PGND which is not smooth connected to GND. A GND terminal is connected to the stable GND plane. And connect it to a GND plane after smoothing PGND by CIN and COUT. GND and PGND are separated inside IC. And connect it to a GND plane after smoothing PGND by CIN and COUT. Connect the heat sink of IC to a GND plane through Thermal Via. And Connect with the largest possible pattern. It is satisfactory even if it connects with the GND terminal of IC. Connect LED current setting resistor RISET nearest to ISET pin. There is possibility to oscillate when capacity is added to ISET terminal, so pay attention that capacity isn't added. And, RISET of GND side must be wired directly to GND(7pin) pin. When those pins are not connected directly near the chip, influence is given to the performance of BD6586MUV, and may limit the current drive performance. As for the wire to the inductor, make its resistance component small so as to reduce electric power consumption and increase the entire efficiency. A layout pattern in consideration of these is shown in p.12. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 9/19 2011.6 - Rev.C BD6586MUV ●Recommended PCB layout pattern Technical Note SBD Coil CIN COUT BD6586MUV CVBAT RISET Fig.10 Frontal surface Fig.11 Rear surface www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 10/19 2011.6 - Rev.C BD6586MUV ●Selection of external parts Recommended external parts are as shown below. When to use other parts than these, select the following equivalent parts. ▪Coil Value 4.7μH 4.7μH 4.7μH 4.7μH 10μH 4.7μH 10μH ▪Capacitor Value Manufacturer TOKO TOKO TOKO TDK TDK TDK TDK Pressure Product number A915AY-4R7M B1015AS-4R7M A1101AS-4R7M LTF5022T-4R7N2R0 LTF5022T-100M1R4 VLP6810T-4R7M1R6 VLP6810T-100M1R1 Manufacturer Vertical 5.2 8.4 4.1 5.0 5.0 6.3 6.3 Size Horizontal 5.2 8.3 4.1 5.2 5.2 6.8 6.8 Size Horizontal 1.6 1.25 0.8 1.25 1.25 1.6 1.25 1.6 Height (MAX) 3.0 4.0 1.2 2.2 2.2 1.0 1.0 Technical Note DC current (mA) 1870 3300 1400 2000 1400 1600 1100 TC B X5R B B B B B B DCR (Ω) 0.045 0.038 0.115 0.073 0.140 0.167 0.350 Product number GRM319B31E475K GRM21BR61E475K GRM188B11A105K GRM219B31A475K GRM219B3YA105K GRM31MB31H105K GRM21BB31H105K GRM31CB31H225K Product number Vertical 3.2 2.0 1.6 2.0 2.0 3.2 2.0 3.2 Height 0.85±0.1 1.25±0.1 0.8±0.1 0.85±0.1 0.85±0.1 1.15±0.1 1.25±0.1 1.6±0.2 Cap Tolerance +/-10% +/-10% +/-10% +/-10% +/-10% +/-10% +/-10% +/-10% [ Power supply capacitor ] 4.7μF 25V MURATA 4.7μF 25V MURATA 1μF 10V MURATA 4.7μF 10V MURATA [ Output capacitor ] 1μF 35V MURATA 1μF 50V MURATA 1μF 50V MURATA 2.2μF 50V MURATA ▪Resistor Value Tolerance Manufacturer Vertical 0.6 Size Horizontal 0.3 Size Horizontal 1.6 Height 0.23±0.03 [ Resistor for LED current decision ] 24kΩ ±0.5% ROHM MCR006YZPD243 ▪SBD Pressure 60V Manufacturer ROHM Product number RB160M-60 Vertical 3.5 Height 0.8±0.1 The coil is the part that is most influential to efficiency. Select the coil whose direct current resistor (DCR) and current inductance characteristic is excellent. BD6586MUV is designed for the inductance value of 4.7µH. Don’t use the inductance value less than 2.2µH. Select a capacitor of ceramic type with excellent frequency and temperature characteristics. Further, select Capacitor to be used with small direct current resistance, and pay sufficient attention to the layout pattern shown in P.10. ●Attention point of PCB layout In PCB layout design, the wiring of power supply line should be low Impedance, and put the bypass capacitor if necessary. Especially the wiring impedance must be lower around the DC/DC converter. ●About heat loss In heat design, operate the DC/DC converter in the following condition. (The following temperature is a guarantee temperature, so consider the margin.) 1. Periphery temperature Ta must be less than 85 ℃. 2. The loss of IC must be less than dissipation Pd. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 11/19 2011.6 - Rev.C BD6586MUV ●Application example ・LED current setting controlled ISET resistor. 24kΩ : 20mA 30kΩ : 16mA 19.6kΩ : 24.5mA 33kΩ : 14.5mA ・Brightness control Please input PWM pulse from EN1, EN2 or PWM terminal. Please refer electrical function p.7. 7 inch panel Battery 2.7V to 5.5V Technical Note 4.7μF 4.7μH 2.2μF 1μF 6LED x 4Parallel SW TRSW 100Hz~1kHz PWM SW SW VBAT VDET EN2 LED1 EN1 LED2 PWM TESTO TEST PGND PGND GND GND GND ISET LED3 LED4 Each 20mA Can be set up to each 10~25mA 24kΩ Fig.12 6 series×4 parallel, LED current 20mA setting Power control PWM application 5inch panel Battery 2.7V to 5.5V 4.7μF 4.7μH 2.2μF 1μF 6LED x 3Parallel Power ON/OFF 100Hz~10kHz PWM SW TRSW EN2 SW SW VBAT VDET LED1 EN1 LED2 PWM TESTO TEST PGND PGND GND GND GND ISET LED3 LED4 Each 20mA Can be set up to each 10~25mA 24kΩ Fig.13 6 series×3 parallel, LED current 20mA setting Current driver PWM application www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 12/19 2011.6 - Rev.C BD6586MUV ●Application example ・LED current setting controlled ISET resistor. 24kΩ : 20mA 30kΩ : 16mA 19.6kΩ : 24.5mA 33kΩ : 14.5mA ・Brightness control Please input PWM pulse from EN1, EN2 or PWM terminal. Please refer electrical function p.7. 5 inch panel Battery 2.7V to 5.5V Technical Note 4.7μF 4.7μH 2.2μF 1μF 4LED x 4Parallel SW TRSW EN2 Power ON/OFF EN1 SW SW VBAT VDET LED1 LED2 PWM LED3 TEST PGND PGND GND GND GND ISET LED4 100Hz~10kHz PWM TESTO Each 20mA Can be set up to each 10~25mA 24kΩ Fig.14 4 series×4 parallel, LED current 20mA setting Current driver PWM application B attery 2.7V to 5.5V 4.7μ F 4.7μ H 2.2μF 1μF 5LED x 3Parallel Power ON/OFF 100Hz~10kHz PWM SW TRSW EN2 SW SW VBAT VDET L ED1 EN1 LED2 PWM TESTO TEST PGND PGND GND GND G ND ISET LED3 L ED4 24kΩ E ach 20mA Can be set up to each 10~25mA Fig.15 5 series×3 parallel, LED current 20mA setting Current driver PWM application www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 13/19 2011.6 - Rev.C BD6586MUV ●Application example ・LED current setting controlled ISET resistor. 24kΩ : 20mA 30kΩ : 16mA 19.6kΩ : 24.5mA 33kΩ : 14.5mA ・Brightness control Please input PWM pulse from EN1, EN2 or PWM terminal. Please refer electrical function p.7. Less than 5 inch panel Battery 2.7V to 5.5V Technical Note 4.7μF 4.7μH 2.2μF 1 μF 6LED x 2Parallel SW TRSW EN2 Power ON/OFF EN1 SW SW VBAT VDET LED1 LED2 PWM LED3 TEST PGND PGND GND GND GND ISET LED4 100Hz~10kHz PWM TESTO Each 20mA Can be set up to each 10~25mA 24kΩ Fig.16 6 series×2 parallel, LED current 20mA setting Current driver PWM application Battery 2.7V to 5.5V 4.7μF 4.7μH 2.2μF 1μF 6LED x 2Parallel SW TRSW 100Hz~1kHz PWM SW SW VBAT VDET EN2 LED1 EN1 LED2 PWM TESTO TEST PGND PGND GND GND GND ISET LED3 LED4 Each 40mA Can be set up to each 20~50mA 24kΩ Fig.17 6 series×2 parallel, LED current 40mA setting Power control PWM application www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 14/19 2011.6 - Rev.C BD6586MUV ●Application example ・LED current setting controlled ISET resistor. 24kΩ : 20mA 30kΩ : 16mA 19.6kΩ : 24.5mA 33kΩ : 14.5mA ・Brightness control Please input PWM pulse from EN1, EN2 or PWM terminal. Please refer electrical function p.7. Less than 5 inch panel Technical Note Battery 2.7V to 5.5V 4.7μF 4.7μH 2.2μF 1μF 2LED x 3Parallel Power ON/OFF 100Hz~10kHz PWM SW TRSW EN2 SW SW VBAT VDET LED1 EN1 LED2 PWM TESTO TEST PGND PGND GND GND GND ISET LED3 LED4 Each 20mA Can be set up to each 10~25mA 24kΩ Fig.18 2 series×3 parallel, LED current 20mA setting Current driver PWM application Battery 2.7V to 5.5V 4.7μF 4.7μH 2.2μF 1μF 6LED x 2Parallel SW TRSW 100Hz~1kHz PWM SW SW VBAT VDET EN2 LED1 EN1 LED2 PWM TESTO TEST PGND PGND GND GND GND ISET LED3 LED4 Each 40mA Can be set up to each 20~50mA 24kΩ Fig.19 3 series×2 parallel, LED current 40mA setting Power control PWM application www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 15/19 2011.6 - Rev.C BD6586MUV ●Application example ・LED current setting controlled ISET resistor. 24kΩ : 20mA 30kΩ : 16mA 19.6kΩ : 24.5mA 33kΩ : 14.5mA ・Brightness control Please input PWM pulse from EN1, EN2 or PWM terminal. Please refer electrical function p.7. For big current LED Battery 2.7V to 5.5V Technical Note 4.7μF 4.7μH 2.2μF 1μF 6LED x 1Parallel Power ON/OFF 100Hz~10kHz PWM SW TRSW EN2 SW SW VBAT VDET LED1 EN1 LED2 PWM TESTO TEST PGND PGND GND GND GND ISET LED3 LED4 Each 60mA Can be set up to each 30~75mA 24kΩ Fig.20 6 series×1 parallel, LED current 60mA setting Current driver PWM application Battery 2.7V to 5.5V 4.7μF 4.7μH 2.2μF 1μF 6LED x 1Parallel SW TRSW 100Hz~1kHz PWM SW SW VBAT VDET EN2 LED1 EN1 LED2 PWM TESTO TEST PGND PGND GND GND GND ISET LED3 LED4 Each 80mA Can be set up to each 40~100mA 24kΩ Fig.21 6 series×1 parallel, LED current 80mA setting Power control PWM application www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 16/19 2011.6 - Rev.C BD6586MUV ●Application example ・LED current setting controlled ISET resistor. 24kΩ : 20mA 30kΩ : 16mA 19.6kΩ : 24.5mA 33kΩ : 14.5mA ・Brightness control Please input PWM pulse from EN1, EN2 or PWM terminal. Please refer electrical function p.7. For the application of 7V and more Other Power Supply 6.0Vto25V Technical Note Battery 2.7V to 5.5V 1μF 4.7μF 4.7μH 2.2μF 6LED x 4Parallel SW TRSW EN2 Power ON/OFF EN1 SW SW VBAT VDET LED1 LED2 PWM TESTO TEST PGND PGND GND GND GND ISET LED3 LED4 Each 20mA Can be set up to each 20~50mA 24kΩ Fig.22 6 series×4 parallel, LED current 20mA setting Power control PWM application ●Analog style optical application Control LED current to charged D/A voltage. Show application example and typ control. Please decide final value after you evaluated application, characteristic. B attery 2.7V to 5.5V 4.7μ F 4.7μ H 2.2μF 1μF 6LED x 4Parallel SW TRSW EN2 Power ON/OFF EN1 SW SW V BAT VDET L ED1 LED2 PWM TESTO TEST PGND PGND GND GND G ND ISET LED3 L ED4 D/A 0.05V 0.2V 0.4V 0.5V 0.6V 0.7V LED current 19.4mA 14.4mA 7.7mA 4.4mA 1.0mA 0mA ISET voltage ISET voltage -D/A + ×800 470kΩ 24kΩ 0.6V 470kΩ + 0.6V-D/A 24kΩ ×800 LED current = E ach 20mA Can be set up to each 10~25mA 470Ω 24kΩ typ LED current = D/A Fig.23 Analog style optical application www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 17/19 2011.6 - Rev.C BD6586MUV Technical Note ●Notes for use (1) Absolute Maximum Ratings An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc., can break down devices, thus making impossible to identify breaking mode such as a short circuit or an open circuit. If any special mode exceeding the absolute maximum ratings is assumed, consideration should be given to take physical safety measures including the use of fuses, etc. (2) Operating conditions These conditions represent a range within which characteristics can be provided approximately as expected. The electrical characteristics are guaranteed under the conditions of each parameter. (3) Reverse connection of power supply connector The reverse connection of power supply connector can break down ICs. Take protective measures against the breakdown due to the reverse connection, such as mounting an external diode between the power supply and the IC’s power supply terminal. (4) Power supply line Design PCB pattern to provide low impedance for the wiring between the power supply and the GND lines. In this regard, for the digital block power supply and the analog block power supply, even though these power supplies has the same level of potential, separate the power supply pattern for the digital block from that for the analog block, thus suppressing the diffraction of digital noises to the analog block power supply resulting from impedance common to the wiring patterns. For the GND line, give consideration to design the patterns in a similar manner. Furthermore, for all power supply terminals to ICs, mount a capacitor between the power supply and the GND terminal. At the same time, in order to use an electrolytic capacitor, thoroughly check to be sure the characteristics of the capacitor to be used present no problem including the occurrence of capacity dropout at a low temperature, thus determining the constant. (5) GND voltage Make setting of the potential of the GND terminal so that it will be maintained at the minimum in any operating state. Furthermore, check to be sure no terminals are at a potential lower than the GND voltage including an actual electric transient. (6) Short circuit between terminals and erroneous mounting In order to mount ICs on a set PCB, pay thorough attention to the direction and offset of the ICs. Erroneous mounting can break down the ICs. Furthermore, if a short circuit occurs due to foreign matters entering between terminals or between the terminal and the power supply or the GND terminal, the ICs can break down. (7) Operation in strong electromagnetic field Be noted that using ICs in the strong electromagnetic field can malfunction them. (8) Inspection with set PCB On the inspection with the set PCB, if a capacitor is connected to a low-impedance IC terminal, the IC can suffer stress. Therefore, be sure to discharge from the set PCB by each process. Furthermore, in order to mount or dismount the set PCB to/from the jig for the inspection process, be sure to turn OFF the power supply and then mount the set PCB to the jig. After the completion of the inspection, be sure to turn OFF the power supply and then dismount it from the jig. In addition, for protection against static electricity, establish a ground for the assembly process and pay thorough attention to the transportation and the storage of the set PCB. (9) Input terminals In terms of the construction of IC, parasitic elements are inevitably formed in relation to potential. The operation of the parasitic element can cause interference with circuit operation, thus resulting in a malfunction and then breakdown of the input terminal. Therefore, pay thorough attention not to handle the input terminals, such as to apply to the input terminals a voltage lower than the GND respectively, so that any parasitic element will operate. Furthermore, do not apply a voltage to the input terminals when no power supply voltage is applied to the IC. In addition, even if the power supply voltage is applied, apply to the input terminals a voltage lower than the power supply voltage or within the guaranteed value of electrical characteristics. (10) Ground wiring pattern If small-signal GND and large-current GND are provided, It will be recommended to separate the large-current GND pattern from the small-signal GND pattern and establish a single ground at the reference point of the set PCB so that resistance to the wiring pattern and voltage fluctuations due to a large current will cause no fluctuations in voltages of the small-signal GND. Pay attention not to cause fluctuations in the GND wiring pattern of external parts as well. (11) External capacitor In order to use a ceramic capacitor as the external capacitor, determine the constant with consideration given to a degradation in the nominal capacitance due to DC bias and changes in the capacitance due to temperature, etc. (12) Thermal shutdown circuit (TSD) When junction temperatures become 175°C (typ) or higher, the thermal shutdown circuit operates and turns a switch OFF. The thermal shutdown circuit, which is aimed at isolating the LSI from thermal runaway as much as possible, is not aimed at the protection or guarantee of the LSI. Therefore, do not continuously use the LSI with this circuit operating or use the LSI assuming its operation. (13) Thermal design Perform thermal design in which there are adequate margins by taking into account the permissible dissipation (Pd) in actual states of use. (14) Selection of coil Select the low DCR inductors to decrease power loss for DC/DC converter. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 18/19 2011.6 - Rev.C BD6586MUV ●Ordering part number Technical Note B D 6 Part No. 6586 5 8 6 M U V - E 2 Part No. Package MUV: VQFN024V4040 Packaging and forming specification E2: Embossed tape and reel VQFN024V4040 4.0±0.1 4.0±0.1 Tape Quantity Embossed carrier tape 2500pcs E2 The direction is the 1pin of product is at the upper left when you hold 1.0MAX 1PIN MARK S +0.03 0.02 -0.02 (0.22) Direction of feed ( reel on the left hand and you pull out the tape on the right hand ) 0.08 S C0.2 1 24 2.4±0.1 6 0.4±0.1 19 18 13 12 0.75 0.5 2.4±0.1 7 +0.05 0.25 -0.04 1pin Direction of feed (Unit : mm) Reel ∗ Order quantity needs to be multiple of the minimum quantity. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 19/19 2011.6 - Rev.C Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. R1120A
BD6586MUV_11 价格&库存

很抱歉,暂时无法提供与“BD6586MUV_11”相匹配的价格&库存,您可以联系我们找货

免费人工找货