BD7LS14G-CTL

Datasheet General Purpose CMOS Logic IC Automotive Single Schmitt Trigger Inverter BD7LS14G-C General Description Key Specifications The BD7LS14G-C is a Single Schmitt Trigger Inverter and qualified for automotive applications. This is designed for 1.65 V to 5.5 V power supply voltage operation. When it is power down, the Output Tolerant circuit protects the output circuit from the back flow current through the connected system. ◼ ◼ ◼ ◼ ◼ Features Supply Voltage Range: 1.65 V to 5.5 V Low Current Consumption (ICC): 10 μA (Max) Operating Temperature Range: -40 °C to +125 °C Max Propagation Delay Time: 12.0 ns (@3.0 V) Output Drive Capability: ±24 mA (@3.0 V) Package W(Typ) x D (Typ) x H (Max) SSOP5 2.9 mm x 2.8 mm x 1.25 mm ◼ AEC-Q100 Qualified(Note 1) ➢ 4000 V Human-body Model ➢ 1000 V Charged-device Model ◼ Low Power Consumption ◼ 5.5 V Tolerant Inputs ◼ Output Tolerant Supports Partial Power Down Mode Operation ◼ Package SSOP5 is Similar to SOT-23-5(JEDEC) SSOP5 (Note 1) Grade 1 Applications ◼ Automotive Pin Descriptions Pin Configuration and Logic Diagram Truth Table 〇Product structure : Silicon integrated circuit .www.rohm.com © 2020 ROHM Co., Ltd. All rights reserved. TSZ22111 • 14 • 001 〇This product has no designed protection against radioactive rays 1/10 TSZ02201-0G4G0GZ00060-1-2 21.Apr.2020 Rev.001 BD7LS14G-C Absolute Maximum Ratings (Ta = 25 °C) Parameter Symbol Rating Unit Supply Voltage Range VCC -0.5 to +6.5 V Input Voltage Range VIN -0.5 to +6.5 V Input Diode Current (VIN < 0) IIK -50 mA Output Diode Current (VO < 0) IOK -50 mA Output Current IO ±50 mA VCC-GND Current Maximum Junction Temperature Storage Temperature Range ICC ±50 mA Tjmax +150 °C Tstg -55 to +150 °C Caution 1: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated over the absolute maximum ratings. Caution 2: Should by any chance the maximum junction temperature rating be exceeded the rise in temperature of the chip may result in deterioration of the properties of the chip. In case of exceeding this absolute maximum rating, design a PCB with thermal resistance taken into consideration by increasing board size and copper area so as not to exceed the maximum junction temperature rating. Thermal Resistance (Note 1) Parameter Thermal Resistance (Typ) Symbol Unit 1s(Note 3) 2s2p(Note 4) θJA 376.5 185.4 °C/W ΨJT 40 30 °C/W SSOP5 Junction to Ambient Junction to Top Characterization Parameter Layer Number of Measurement Board Single (Note 2) Material Board Size FR-4 114.3 mm x 76.2 mm x 1.57 mmt Top Copper Pattern Thickness Footprints and Traces 70 μm Layer Number of Measurement Board 4 Layers Material Board Size FR-4 114.3 mm x 76.2 mm x 1.6 mmt Top 2 Internal Layers Bottom Copper Pattern Thickness Copper Pattern Thickness Copper Pattern Thickness Footprints and Traces 70 μm 74.2 mm x 74.2 mm 35 μm 74.2 mm x 74.2 mm 70 μm (Note 1) Based on JESD51-2A (Still-Air). (Note 2) The thermal characterization parameter to report the difference between junction temperature and the temperature at the top center of the outside surface of the component package. (Note 3) Using a PCB board based on JESD51-3. (Note 4) Using a PCB board based on JESD51-7. Recommended Operating Conditions Parameter Symbol Min Typ Max Unit Conditions 1.65 - 5.5 V Operating 1.5 - 5.5 V Data Retention Only Supply Voltage VCC Input Voltage VIN 0 - 5.5 V - Output Voltage VO 0 - VCC V - Topr -40 - +125 °C - Operating Temperature (Note) The recommended operating conditions are the range where operation is guaranteed. If this ranges are exceeded, operation is not guaranteed even within the absolute maximum ratings. Unused inputs must be tied to either VCC or GND. .www.rohm.com © 2020 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15• 001 2/10 TSZ02201-0G4G0GZ00060-1-2 21.Apr.2020 Rev.001 BD7LS14G-C Electrical Characteristics (Unless otherwise specified VCC = 1.65 V to 5.5 V and Ta = -40 °C to +125 °C) Parameter Positive Threshold Voltage Negative Threshold Voltage Hysteresis Voltage Output “H” Voltage Output “L” Voltage Input Current Power Off Output Pin Current Quiescent Supply Current Supply Current Increase Input Capacitance Symbol VP VN VH VOH VOL Unit Conditions Min Typ Max 0.60 - 1.40 1.65 V 0.70 - 1.50 1.8 V 1.00 - 1.80 1.30 - 2.20 1.90 - 3.10 4.5 V 2.20 - 3.60 5.5 V 0.20 - 0.80 1.65 V 0.25 - 0.90 1.8 V 0.40 - 1.15 0.60 - 1.50 1.00 - 2.00 1.20 - 2.40 5.5 V 0.10 - 1.00 1.65 V 0.15 - 1.00 1.8 V 0.25 - 1.10 0.40 - 1.20 0.60 - 1.50 4.5 V 0.70 - 1.70 5.5 V VCC - 0.1 - - 1.65 V to 5.5 V 1.2 - - 1.65 V IOH = -4 mA 1.8 - - 2.3 V IOH = -8 mA 2.3 - - 3.0 V IOH = -16 mA 2.1 - - 3.0 V IOH = -24 mA 3.4 - - 4.5 V IOH = -32 mA - - 0.10 1.65 V to 5.5 V IOL = 100 μA - - 0.45 1.65 V IOL = 4 mA - - 0.40 2.3 V IOL = 8 mA - - 0.60 3.0 V IOL = 16 mA - - 0.90 3.0 V IOL = 24 mA 4.5 V IOL = 32 mA V V VCC 2.3 V 3.0 V 2.3 V 3.0 V V V V 2.3 V 3.0 V - - 1.00 - - ±2 μA 0 V to 5.5 V IOFF - - 10 μA 0V ICC - - 10 μA 1.65 V to 5.5 V ΔICC - - 600 μA 3.0 V to 5.5 V CI - 4 - pF 3.3 V 3/10 - 4.5 V IIN .www.rohm.com © 2020 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15• 001 - - IOH = -100 μA VIN = 5.5 V or GND VIN or VO = 5.5 V Input: VCC - 0.6 V VIN = VCC or GND Ta = 25 °C TSZ02201-0G4G0GZ00060-1-2 21.Apr.2020 Rev.001 BD7LS14G-C Switching Characteristics (Unless otherwise specified VCC = 1.65 V to 5.5 V and Ta = -40 °C to +125 °C) Parameter Propagation Delay Time Power Dissipation Capacitance Symbol tPLH tPHL FROM (Input) TO (Output) A Y Min Typ Max 1.9 - 16.0 1.0 - 13.0 0.9 - 12.0 0.6 - 11.0 Unit Conditions VCC 1.65 V to 1.95 V ns 2.3 V to 2.7 V - 3.0 V to 3.6 V - 4.5 V to 5.5 V - - - - 29 - pF 3.3 V - - - 35 - pF 5.0 V CPD f = 10 MHz, Ta = 25 °C f = 10 MHz, Ta = 25 °C Parameter Measurement Conditions Measurement Circuit and Timing Chart .www.rohm.com © 2020 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15• 001 4/10 TSZ02201-0G4G0GZ00060-1-2 21.Apr.2020 Rev.001 BD7LS14G-C Typical Performance Curves Figure 1. Propagation Delay Time: tPLH vs Supply Figure 2. Propagation Delay Time: tPLH vs Ambient Voltage: VCC Temperature: Ta (Ta = 25 °C) (VCC = 3.3 V) Figure 3. Propagation Delay Time: tPHL vs Supply Figure 4. Propagation Delay Time: tPHL vs Ambient Voltage: VCC Temperature: Ta (Ta = 25 °C) .www.rohm.com © 2020 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15• 001 (VCC = 3.3 V) 5/10 TSZ02201-0G4G0GZ00060-1-2 21.Apr.2020 Rev.001 BD7LS14G-C Operational Notes 1. Reverse Connection of Power Supply Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when connecting the power supply, such as mounting an external diode between the power supply and the IC’s power supply pins. 2. Power Supply Lines Design the PCB layout pattern to provide low impedance supply lines. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and aging on the capacitance value when using electrolytic capacitors. 3. Ground Voltage Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition. 4. Ground Wiring Pattern When using both small-signal and large-current ground traces, the two ground traces should be routed separately but connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal ground caused by large currents. Also ensure that the ground traces of external components do not cause variations on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance. 5. Recommended Operating Conditions The function and operation of the IC are guaranteed within the range specified by the recommended operating conditions. The characteristic values are guaranteed only under the conditions of each item specified by the electrical characteristics. 6. Inrush Current When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush current may flow instantaneously due to the internal powering sequence and delays, especially if the IC has more than one power supply. Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and routing of connections. 7. Operation Under Strong Electromagnetic Field Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction. 8. Testing on Application Boards When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may subject the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply should always be turned off completely before connecting or removing it from the test setup during the inspection process. To prevent damage from static discharge, ground the IC during assembly and use similar precautions during transport and storage. 9. Inter-pin Short and Mounting Errors Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin. Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and unintentional solder bridge deposited in between pins during assembly to name a few. 10. Unused Input Pins Input pins of an IC are often connected to the gate of a MOS transistor. The gate has extremely high impedance and extremely low capacitance. If left unconnected, the electric field from the outside can easily charge it. The small charge acquired in this way is enough to produce a significant effect on the conduction through the transistor and cause unexpected operation of the IC. So unless otherwise specified, unused input pins should be connected to the power supply or ground line. .www.rohm.com © 2020 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15• 001 6/10 TSZ02201-0G4G0GZ00060-1-2 21.Apr.2020 Rev.001 BD7LS14G-C Operational Notes – continued 11. Regarding the Input Pin of the IC This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them isolated. P-N junctions are formed at the intersection of the P layers with the N layers of other elements, creating a parasitic diode or transistor. For example (refer to figure below): When GND > Pin A and GND > Pin B, the P-N junction operates as a parasitic diode. When GND > Pin B, the P-N junction operates as a parasitic transistor. Parasitic diodes inevitably occur in the structure of the IC. The operation of parasitic diodes can result in mutual interference among circuits, operational faults, or physical damage. Therefore, conditions that cause these Resistor Transistor (NPN) Pin A Pin B C Pin A N P+ N P N P+ N N Parasitic Elements P+ E N P N P+ B N C E Parasitic Elements P Substrate P Substrate Parasitic Elements Pin B B GND Parasitic Elements GND GND N Region close-by GND diodes to operate, such as applying a voltage lower than the GND voltage to an input pin (and thus to the P substrate) should be avoided. Example of Monolithic IC Structure 12. Ceramic Capacitor When using a ceramic capacitor, determine a capacitance value considering the change of capacitance with temperature and the decrease in nominal capacitance due to DC bias and others. .www.rohm.com © 2020 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15• 001 7/10 TSZ02201-0G4G0GZ00060-1-2 21.Apr.2020 Rev.001 BD7LS14G-C Ordering Information B D 7 L S 1 4 G C T L - Package G: SSOP5 Product Rank C: for Automotive Packaging and forming specification TL: Embossed tape and reel Marking Diagram SSOP5 (TOP VIEW) af Part Number Marking LOT Number .www.rohm.com © 2020 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15• 001 8/10 TSZ02201-0G4G0GZ00060-1-2 21.Apr.2020 Rev.001 BD7LS14G-C Physical Dimension and Packing Information SSOP5 Package Name Packing Information Packing Form Embossed carrier tape Quantity 3000 pcs Direction of feed TL .www.rohm.com © 2020 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15• 001 9/10 TSZ02201-0G4G0GZ00060-1-2 21.Apr.2020 Rev.001 BD7LS14G-C Revision History Date Revision 21.Apr.2020 001 Changes New Release .www.rohm.com © 2020 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15• 001 10/10 TSZ02201-0G4G0GZ00060-1-2 21.Apr.2020 Rev.001 Notice Precaution on using ROHM Products 1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅢ CLASSⅣ CLASSⅢ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (Exclude cases where no-clean type fluxes is used. However, recommend sufficiently about the residue.); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse, is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in the range that does not exceed the maximum junction temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice-PAA-E © 2015 ROHM Co., Ltd. All rights reserved. Rev.004 Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl 2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign trade act, please consult with ROHM in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the Products with other articles such as components, circuits, systems or external equipment (including software). 3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the Products, subject to the terms and conditions herein. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice-PAA-E © 2015 ROHM Co., Ltd. All rights reserved. Rev.004 Datasheet General Precaution 1. Before you use our Products, you are requested to carefully read this document and fully understand its contents. ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of any ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this document is current as of the issuing date and subject to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sales representative. 3. The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccuracy or errors of or concerning such information. Notice – WE © 2015 ROHM Co., Ltd. All rights reserved. Rev.001