BD8671KN

1/4 STRUCTURE PRODUCT NAME MODEL NAME BLOCK DIAGRAM ◎FEATURES： ： ： ： ： Silicon Monolithic Integrated Circuit DC/DC converter IC for camera module for car navigation system BD8671KN Fig. - 2 ・+3.3V output Step down DC/DC converter for asynchronous rectification system ・+12V output Boost DC/DC converter for asynchronous rectification system ・-5V output Voltage control charge pump for reversing type for negative voltage ・Soft start function ・Building in low voltage and over voltage protection function ・Building in terminal RT OPEN/Short protection ・The frequency can be set by external resistance ・Concentrated protection control with built-in sequencer ・VQFN-28 package ◎ABSOLUTE MAXIMUM RATING:（Ta=25℃） Parameter VIN supply voltage PVIN supply voltage Input terminal voltage 1*1 Input terminal voltage 2*2 Input terminal voltage 3*3 Input terminal voltage 4*4 Output terminal voltage 1*5 Output terminal voltage 2*6 Output terminal voltage 3*7 Output terminal voltage 4*8 Output terminal voltage 5*9 Power dissipation Operating temperature Storage temperature *1 *4 *8 *10 *11 Symbol VIN PVIN VIN1 VIN2 VIN3 VIN4 VOUT1 VOUT2 VOUT3 VOUT4 VOUT5 Pd Topr Tstg -0.3 -0.3 -0.3 -0.3 -0.3 -10.0 -0.3 -0.3 -0.3 -0.3 VIN4 -40 -55 Limits ～ ～ ～ ～ ～ ～ ～ ～ ～ ～ ～ 0.725*11 ～ ～ +18.0 VIN VIN +20.0 +20.0 +0.3 VIN PVIN +20.0 VIN3*10 +0.3 +85 +150 Unit V V V V V V V V V V V W ℃ ℃ FB12、SS12、TEST1、TEST2、TEST3、RT、CTL1、CTL2、CTL3、SS33、V33 terminal voltage *2 V12 terminal voltage *3 V12IN terminal voltage MV8 terminal voltage *5 FC12 terminal voltage *6 SW33 terminal voltage *7 SW12 terminal voltage V8、CP terminal voltage *9 MV5、CM terminal voltage V8 terminal voltage ABSOLUTE MAXIMUM RATING is VIN3 or 10V is low. Between V8 terminal voltage and MV5 terminal voltage ABSOLUTE MAXIMUM RATING is 15V. 70mm×70mm, thickness1.6mm, less than 3% share of copper foil when implementing glass epoxy board. Operating at higher than Ta=25℃, 5.8mW shall be reduced per 1 ◎OPERATION CONDITION Parameter (Please set the power-supply voltage in consideration of a power dissipation.) Symbol MIN 4.5 TYP 6.0 MAX 9.0 Unit V VIN supply voltage VIN This product is not designed for protection against radioactive rays. REV. A 2/4 ◎ELECTRICAL CHARACTERISTICS (Unless otherwise noted Ta=25℃, VIN=6.0V,PVIN=6.0V,CTL1,2,3=6.0V,GND=0V) Parameter VIN,PVIN Circuit current 1 VIN,PVIN Circuit current 2 V12IN Circuit current Range of DC/DC converter oscillation frequency setting Symbol IQ1 IQ2 IQ３ FOSC V033 RV33DIS ISS33 VSS33TH VSS33CLM VSS33STB VSS33STB_HYS RSS33DIS VSS33PON VSS33PON_HYS VV33LVP VV33LVP_HYS VV33OVP V012 RV12DIS VFC12H VFC12L IFC12SINK IFC12SOURCE ISS12 VSS12TH VSS12CLM VSS12STB VSS12STB_HYS RSS12DIS VSS12PON VSS12PON_HYS VV12LVP VV12LVP_HYS VV12OVP VMV5 RMV5DIS VMV5OVP VMV5PON VMV5LVP VMV5LVP_HYS specification value MIN 500 3.234 270 -4.0 1.0 1.6 0.11 5 4.9 1.0 10 1.11 41.2 4.45 11.76 270 1.2 0.3 -4.0 1.0 1.6 0.11 5 4.9 1.0 10 4.0 0.15 16.2 -5.10 200 -8.25 -4.5 -2.5 62.5 TYP 0 4.1 2.3 1000 3.300 390 -2.5 1.1 1.9 0.15 50 7.0 1.1 100 1.32 412 4.95 12.00 390 -2.5 1.1 1.9 0.15 50 7.0 1.1 100 4.8 1.5 18.0 -5.00 320 -7.50 -3.5 -2.0 625 MAX 50 6.1 3.3 1200 3.366 500 -1.0 1.2 2.2 0.19 100 9.1 1.2 200 1.53 824 5.45 12.24 500 0.2 -14 -1.0 1.2 2.2 0.19 100 9.1 1.2 200 5.6 3.0 19.8 -4.90 430 -6.75 -2.5 -1.5 1250 UNIT μA mA mA kHz V Ω μA V V V mV kΩ V mV V mV V V Ω V V mA μA μA V V V mV kΩ V mV V V V V Ω V V V mV Condition CTL1,2,3=0V CTL1,2,3=VIN、 VV33=3.5V VV12=13.0V 、VV12IN=12.0V CTL1,2,3=VIN、 VV33=3.5V VV12=13.0V 、VV12IN=12.0V It is possible to set it with the terminal RT. 3.3V output voltage Terminal SS Discharge resistance Terminal SS Charging current Terminal SS Threshold voltage Terminal SS Clamping voltage Terminal SS Standby voltage Terminal SS Standby voltage Maximum hysteresis error Terminal SS Discharge resistance Terminal SS Protection circuit start voltage Terminal SS Protection circuit start voltage Maximum hysteresis error Terminal V33 Low voltage detection voltage Terminal V33 Low voltage detection Maximum hysteresis error Terminal V33 Overvoltage detection voltage CTL1,2,3=0V VSS33=1.0V VSS33voltage、VV33=3.3V VSS33 voltage (L→H) CTL1,2,3=6.0→0.0V VSS33 voltage (L→H) VSS33 voltage VV33 voltage (H→L) VV33 voltage VV33 voltage (L→H) < Boost DC/DC converter of 12V output part > 12V output voltage Terminal V12 Discharge resistance Terminal FC12 Clamping voltage H Terminal FC12 Clamping voltage L Terminal FC12 Sink current Terminal FC12 Source current Terminal SS12 Charging current Terminal SS12 Threshold voltage Terminal SS12 Clamping voltage Terminal SS12 Standby voltage Terminal SS12 Standby voltage Maximum hysteresis error Terminal SS12 Discharge resistance Terminal SS12 Protection circuit start voltage Terminal SS12 Protection circuit start voltage Maximum hysteresis error Terminal V12Low voltage detection voltage Terminal V12 Low voltage detection Maximum hysteresis error Terminal V12 Overvoltage detection voltage CTL1,2,3=0V VV12=10.5V VV12=13.5V VV12=13.5V、VFC12=0.4V VV12=10.5V、VFC12=1.4V VSS12=1.0V VSS12 voltage、VFB12=0.8V VSS12 voltage (L→H) CTL1,2,3=6.0→0.0V VSS12 voltage (L→H) VSS12 voltage VV12 voltage (H→L) VV12 voltage VV12 voltage (L→H) MV8= -8.0V CTL3=0V、VV8=8.0V VMV5 voltage、VV33=3.3V VMV5 voltage (H→L)、VV33=3.3V VMV5 voltage (L→H)、VV33=3.3V VMV5 voltage、V33=3.3V < -5V output reversing charge pump part > Terminal MV5 output voltage Terminal MV5 Discharge resistance Terminal MV5 Overvoltage detection voltage Terminal MV5 Protection circuit start voltage Terminal MV5 Low voltage detection voltage Terminal MV5 Low voltage detection Maximum hysteresis error ●VV33 ： V33 voltage、VVSS33 ： SS33 voltage、VV12： V12 voltage、VFC12 ： FC12 voltage、 VSS12： SS12 voltage、 VMV5 ： MV5 voltage 、VMV8：MV8 voltage、VV8：V8 voltage、VV12IN：V12IN voltage ●This product is not designed for protection against radioactive rays. ●The current ability must not exceed Pd. REV. A 3/4 ◎PIN ASSIGNMENT No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 *12 Symbol V12 FB12 FC12 SS12 PGND12 SW12 TEST2 CTL1 VIN GND RT PVIN CTL3 CTL2 Description 12V output voltage detection terminal Error amplifier input terminal Error amplifier output terminal 12V soft start adjustment capacity connection terminal GND(0V connection) 12V coil connection terminal Test terminal 2(0V is connected and use it usually). 3.3V output control terminal Power supply input terminal GND(0V connection) Frequency adjustment resistance connection terminal Power supply input terminal for PowerTr (=VIN) -5V output control terminal 12V output control terminal (*12) No. 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Symbol TEST1 SW33 PGND33 SS33 V33 TEST3 SGND MV5 MV8 CM PGNDV8 CP V8 V12IN Description Test terminal 2(0V is connected and use it usually). 3.3V coil connection terminal Power GND (the same potential as terminal GND) 3.3V soft start adjustment capacity connection terminal 3.3V output voltage detection terminal Test terminal 3 (It uses it by the open usually.) Sense GND(the same potential as terminal GND) -5V regulator output terminal -8V charge pump output terminal Capacity connection terminal for charge pump (－) Power GND (the same potential as terminal GND) Capacity connection terminal for charge pump (＋) 8V regulator output terminal LDO12V voltage input terminal H->L (ON->OFF) control, When CTL3=L. (Refer to NOTE ON USE-13) ◎PACKAGE OUTLINE ◎BLOCK DIAGRAM VIN Product number V12IN VREG BG D8671 V8 OVP LVP PON PVIN 1pin mark LOT No. V8IN OSC CP PGNDM8 Charge Pump Cntorol OSC D R V SW33 V33 PON,LVP,OVP SEQUENCER PGND33 CM MV8 SS33 V33 MV8IN PGND12 MV5 PON,LVP,OVP D R V SW12 MV5 OSC TSD CTL1 CTL2 CTL3 BG FC12 FB12 VQFN-28 （UNIT：mm） RT OSC OSC V12 PON,LVP,OVP SS12 V12 TSD TEST3 TEST2 TEST1 GND SGND Fig.-１ PACKAGE OUTLINE Fig.-2.BLOCK DIAGRAM REV. A 4/4 ◎NOTE ON USE 1．About the absolute maximum rating Attention is brushed off enough to the quality control, it is likely to destroy when the absolute maximum rating such as impressed voltages (VCC_IN,DCIN) and ranges (Topr) of the operating temperature as it is exceeded, the mode of breakings of the short or the opening, etc. cannot be specified, and examine it in this IC to give physical measures for safety such as fuses when a special mode that exceeds the absolute maximum rating is assumed. 2．About the reverse-connection of the power supply connector IC might destroy it by reversely connecting the power supply connector. Give measures such as putting the diode between power supply terminals of power supply and IC outside for the reverse-touching destruction protection. 3．Power supply line Please do measures such as putting the bypass capacitor in power supply-GND nearest pin of this IC as the route of the resurrection current to cause the return of the current in which it resurrected it by the counter electromotive force of the coil. Please confirm the characteristic of the electrolytic capacitor enough as the capacity omission etc. at the low temperature never happen, and decide it. 4．About grand potential Any state of operation must become the lowest potential about the potential of the terminal GND. Moreover, confirm whether there is terminal that is actually the voltage of GND or less including transients. 5．About the heat design Think about permissible loss (Pd) in an actual state of use, and do the heat design with the margin enough. 6．About the short and the miss-installation between terminals Note the direction and the miss-registration of IC enough when you install it in the set substrate. IC might destroy it as well as reversely connecting the power supply connector when installing it by mistake. Moreover, there is fear of destruction when the foreign body enters between terminals, the terminal, the power supply, and grandeur and it is short-circuited. 7．About operation in strong electromagnetic field In use in strong electromagnetic field, note that there is a possibility of malfunctioning. 8．About the capacitor during output-GND The current charged the capacitor with when VCC is 0V or is GND and is short-circuited when a big capacitor is connected between GND output by some factors flows into the output and it is likely to destroy it. Give the capacitor between GND output to 0.1μF or less. 9．About the inspection by the set substrate It is likely to suffer stress to IC and discharge electricity every one process when you connect the capacitor with the pin with low impedance when inspecting it in the set substrate. Moreover, detach it after connecting after the power supply is turned off without fail when detaching it to G in the inspection process, inspecting, and turning off the power supply. n addition, be give the earth to the assembly process as a static electricity measures, and careful enough when it transports and you preserve it. 10．About each input terminal + This IC is a monolithic IC which has a P isolations and P substrate to isolate elements each other. This P layer and an N layer in each element form a PN junction to construct various parasitic elements. For instance, the potential difference operates in resistance as shown in the figure below when resistance and the transistor connect it with the terminal and the playground (GND) >(terminal B) joint of PN operates as a parasitic diode in playground (GND) >(terminal A) transistor (NPN). In addition, the NPN transistor of parasitism works with N layer of the element of the above-mentioned parasitic diode and the neighborhood and others in transistor (NPN). A parasitic element in IC composition is inevitably formed because of the potential relation. A parasitic element can operate, the interference with the circuit operation be caused, it malfunction, and, consequently, it cause destruction. Therefore, do not do the usage that a parasitic element operates as a voltage that is lower than the playground (GND;P substrate) is impressed to the input terminal enough. Moreover, do not impress the voltage to the input terminal when you do not impress the power-supply voltage to IC. Give each input terminal to me the voltage below the power-supply voltage or in the guarantee value of an electric characteristic when you similarly impress the power-supply voltage. Example of IC of simple structure 11．Earth wiring pattern If small signal GND and large current GND exist, disperse their pattern. In addition, for voltage change by pattern wiring impedance and large current not to change voltage of small signal GND, each ground terminal of IC must be connected at the one point on the set circuit board. As for GND of external parts, it is similar to the above-mentioned. 12．Thermal Shut-Down When a thermal shutdown operates, the DC/DC converter controller of all Ch is turned off. When a thermal shutdown is released, the DC/DC converter controller of all Ch becomes an operation beginning from turning off. 13．DC/DC converter control terminal (CTL1,2,3) This IC has 3 output voltage (3.3V,12.0V,-5.0V). When you turning off control 12.0V output from all output ON(CTL1,2,3=H) time with the terminal CTL2, please control 12.0V output turning off with the terminal CTL2 after 200μs or more has passed by the terminal CTL3 since -5.0 the V output was turning off controlled. REV. A Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. R0039A