Datasheet
2.7V to 5.5V, 2.0A 1ch
Synchronous Buck Converter with
Integrated FET
BD9130NV
General Description
Key Specifications
BD9130NV is ROHM’s high efficiency step-down
switching regulator designed to provide a voltage as
low as 1V from a supply voltage of 5.5V/3.3V. It offers
high efficiency by using pulse skip control technology
and synchronous switches, and provides fast transient
response to sudden load changes by implementing
current mode control.
Features
Fast Transient Response because of Current Mode
PWM Control System
High Efficiency for All Load Ranges because of
Synchronous Switches (Nch/Pch FET) and SLLMTM
(Simple Light Load Mode)
Soft-Start Function
Thermal Shutdown and UVLO Functions
Short-Circuit Protection with Time Delay Function
Shutdown Function
Input Voltage Range:
Output Voltage Range:
Output Current:
Switching Frequency:
Pch FET ON-Resistance:
Nch FET ON-Resistance:
Standby Current:
Operating Temperature Range:
Package
2.7V to 5.5V
1.0V to 2.5V
2.0A (Max)
1MHz(Typ)
200mΩ(Typ)
160mΩ(Typ)
0μA (Typ)
-25°C to +105°C
W(Typ) x D(Typ) x H(Max)
Applications
Power Supply for LSI including DSP, Microcomputer
and ASIC
SON008V5060
5.00mm x 6.00mm x 1.00mm
Typical Application Circuit
VCC
CIN
L
EN
VCC,PVCC
SW
ADJ
ITH
VOUT
CO
GND,PGND
R2
R1
RITH
CITH
Figure 1. Typical Application Circuit
○Product structure：Silicon monolithic integrated circuit
.www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・14・001
○This product has no designed protection against radioactive rays
1/21
TSZ02201-0J3J0AJ00130-1-2
02.Oct.2014 Rev.002
BD9130NV
Pin Configuration
(TOP VIEW)
ADJ 1
8 EN
VCC 2
7 PVCC
ITH 3
6 SW
GND 4
5 PGND
Figure 2. Pin Configuration
Pin Description
Pin No.
Pin name
1
2
3
4
5
6
7
8
ADJ
VCC
ITH
GND
PGND
SW
PVCC
EN
Pin function
Output voltage detection pin
Power supply input pin
GmAmp output pin/connected to phase compensation capacitor
Ground pin
Power switch ground pin
Power switch node
Power switch supply pin
Enable pin (Active high)
Block Diagram
VCC
PVCC
VCC
RITH
R1
CITH
R2
Figure 3. Block Diagram
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
2/21
TSZ02201-0J3J0AJ00130-1-2
02.Oct.2014 Rev.002
BD9130NV
Absolute Maximum Ratings
Parameter
VCC Voltage
Symbol
Limit
V
PVCC
-0.3 to +7 (Note 1)
V
VEN
-0.3 to +7
V
VCC
PVCC Voltage
EN Voltage
SW,ITH Voltage
Unit
(Note 1)
-0.3 to +7
VSW,VITH
-0.3 to +7
V
Power Dissipation 1
Pd1
0.90(Note 2)
W
Power Dissipation 2
Pd2
3.90(Note 3)
W
Operating Temperature Range
Topr
-25 to +105
°C
Storage Temperature Range
Tstg
-55 to +150
°C
Tjmax
+150
°C
Maximum Junction Temperature
(Note 1) Pd should not be exceeded.
(Note 2) Reduce by 7.2mW/°C for temperatures above Ta=25°C, Mounted on 70mmx70mmx1.6mm Glass Epoxy PCB.
(Note 3) Reduce by 31.2mW/°C for temperatures above Ta=25°C, Mounted on JESD51-7.
Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit
between pins. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated over the absolute maximum
ratings.
Recommended Operating Conditions (Ta=25°C)
Parameter
VCC voltage
PVCC Voltage
En Voltage
SW Average Output Current
Output Voltage Setting Range
Limit
Symbol
Unit
Min
Typ
Max
VCC (Note 4)
2.7 (Note 5)
3.3
5.5
V
PVCC (Note 4)
2.7 (Note 5)
3.3
5.5
V
VEN
0
-
VCC
V
ISW (Note 4)
-
-
2.0
A
VOUT
1.0
-
2.5
V
(Note 4) Pd should not be exceeded.
(Note 5) In case the output voltage is set to 1.6V or more, VCCMin = VOUT + 1.3V.
Electrical Characteristics(Ta=25°C, VCC=PVCC=3.3V, VEN=VCC, R1=10kΩ, R2=5kΩ, unless otherwise specified.)
Symbol
Min
Typ
Max
Unit
Standby Current
Parameter
ISTB
-
0
10
μA
Bias Current
ICC
-
250
400
μA
Conditions
EN=GND
En Low Voltage
VENL
-
GND
0.8
V
Standby mode
En High Voltage
VENH
2.0
VCC
-
V
Active mode
EN Input Current
IEN
-
1
10
μA
VEN=3.3V
Oscillation Frequency
fOSC
0.8
1
1.2
MHz
Pch Fet ON-Resistance
RONP
-
200
400
mΩ
PVCC=3.3V
Nch Fet ON-Resistance
RONN
-
160
350
mΩ
PVCC=3.3V
ADJ Voltage
VADJ
0.788
0.800
0.812
V
Output Voltage
VOUT
-
1.200
-
V
ITH Sink Current
ITHSI
10
20
-
μA
VADJ=1.0V
ITH Source Current
ITHSO
10
20
-
μA
VADJ=0.6V
UVLO Threshold Voltage
VUVLO1
2.400
2.500
2.600
V
VCC=3V to 0V
UVLO Release Voltage
VUVLO2
2.425
2.550
2.700
V
VCC=0V to 3V
tSS
0.5
1
2
ms
Timer Latch Time
tLATCH
1
2
3
ms
Scp/Tsd operated
Output Short Circuit Threshold Voltage
VSCP
-
VOUTx0.5
VOUTx0.7
V
VOUT=1.2V to 0V
Soft-Start Time
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
3/21
TSZ02201-0J3J0AJ00130-1-2
02.Oct.2014 Rev.002
BD9130NV
[VOUT=2.5V]
Ta=25°C
Ta=25°C
IO=0A
IO=0A
[VOUT=1.8V]
[VOUT=1.8V]
Output Voltage: VOUT [V]
Output Voltage: VOUT [V]
Typical Performance Curves
VCC=3.3V
Ta=25°C
IO=0A
Ta=25°C
IO=0A
EN Voltage: VEN [V]
Input Voltage: VCC [V]
Figure 4. Output Voltage vs Input Voltage
Figure 5. Output Voltage vs EN Voltage
VCC=3.3V
IO=0A
[VOUT=2.5V]
VCC=5V
Ta=25°C
[VOUT=1.8]
VCC=3.3V
Ta=25°C
Output Voltage: VOUT [V]
Output Voltage: VOUT [V]
[VOUT=1.8V]
Output Current: IOUT [A]
Temperature: Ta [°C]
Figure 6. Output Voltage vs Output Current
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
Figure 7. Output Voltage vs Temperature
4/21
TSZ02201-0J3J0AJ00130-1-2
02.Oct.2014 Rev.002
BD9130NV
Typical Performance Curves - continued
Efficiency: η [%]
[VOUT=1.8V]
VCC=3.3V
Ta=25°C
[VOUT=2.5V]
VCC=5V
Ta=25°C
Frequency: fOSC [MHz]
VCC=3.3V
Temperature: Ta [°C]
Output Current: IOUT [mA]
Figure 9. Frequency vs Temperature
Figure 8. Efficiency vs Output Current
VCC=3.3V
EN Voltage: VEN [V]
ON-Resistance: RON [Ω]
VCC=3.3V
Temperature: Ta [°C]
Temperature: Ta [°C]
Figure 11. EN Voltage vs Temperature
Figure 10. ON-Resistance vs Temperature
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
5/21
TSZ02201-0J3J0AJ00130-1-2
02.Oct.2014 Rev.002
BD9130NV
Typical Performance Curves - continued
VCC=3.3V
Frequency: fOSC [MHz]
Circuit Current: ICC [µA]
Ta=25°C
Temperature: Ta [°C]
Input Voltage: VCC [V]
Figure 12. Circuit Current vs Temperature
Figure 13. Frequency vs Input Voltage
Typical Waveforms
[VOUT=1.8V]
VCC=PVCC
=EN
[SLLMTM control
VOUT=1.8V]
SW
VOUT
VOUT
VCC=3.3V
Ta=25°C
IO=0A
VCC=3.3V
Ta=25°C
Figure 14. Soft Start Waveform
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
Figure 15. SW Waveform
(Io=10mA)
6/21
TSZ02201-0J3J0AJ00130-1-2
02.Oct.2014 Rev.002
BD9130NV
Typical Waveforms - continued
[PWM control
[VOUT=1.8V]
VOUT=1.8V]
VOUT
VCC=3.3V
Ta=25°C
IOUT
VCC=3.3V
Ta=25°C
Figure 17. Transient Response
(Io=1A to 2A, 10μs)
Figure 16. SW Waveform
(Io=200mA)
[VOUT=1.8V]
VOUT
IOUT
VCC=3.3V
Ta=25°C
Figure 18. Transient Response
(Io=2A to 1A,10μs)
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
7/21
TSZ02201-0J3J0AJ00130-1-2
02.Oct.2014 Rev.002
BD9130NV
Application Information
1. Operation
BD9130NV is a synchronous step-down switching regulator that achieves fast transient response by employing current
mode PWM control system. It utilizes switching operation either in PWM (Pulse Width Modulation) mode for heavier load, or
SLLMTM (Simple Light Load Mode) operation for lighter load to improve efficiency.
(1) Synchronous Rectifier
Integrated synchronous rectification using two MOSFETS reduces power dissipation and increases efficiency when
compared to converters using external diodes. Internal shoot-through current limiting circuit further reduces power
dissipation.
(2) Current mode PWM Control
The PWM control signal of this IC depends on two feedback loops, the voltage feedback and the inductor current
feedback.
(a) PWM (Pulse Width Modulation) Control
The clock signal coming from OSC has a frequency of 1Mhz. When OSC sets the RS latch, the P-Channel
MOSFET is turned ON and the N-Channel MOSFET is turned OFF. The opposite happens when the current
comparator (Current Comp) resets the RS latch i.e. the P-Channel MOSFET is turned OFF and the N-Channel
MOSFET is turned ON. Current Comp’s output is a comparison of two signals, the current feedback control signal
“SENSE” which is a voltage proportional to the current IL, and the voltage feedback control signal, FB.
(b) SLLMTM (Simple Light Load Mode) Control
When the control mode is shifted by PWM from heavier load to lighter load or vice versa, the switching pulse is
designed to turn OFF with the device held operating in normal PWM control loop. This allows linear operation
without voltage drop or deterioration in transient response during the sudden load changes. Although the PWM
control loop continues to operate with a SET signal from OSC and a RESET signal from Current Comp, it is so
designed such that the RESET signal is continuously sent even if the load is changed to light mode where the
switching is turned OFF and the switching pulses disappear. Activating the switching discontinuously reduces the
switching dissipation and improves the efficiency.
SENSE
Current
Comp
RESET
VOUT
Level
Shift
R Q
FB
SET
Gm Amp
S
IL
Driver
Logic
VOUT
SW
Load
OSC
RITH
Figure19. Diagram of Current Mode PWM Control
PVCC
Current
Comp
SENSE
PVCC
SENSE
Current
Comp
FB
FB
SET
GND
SET
GND
RESET
GND
RESET
GND
SW
GND
SW
IL
GND
IL(AVE)
IL
0A
VOUT
VOUT
VOUT(AVE)
VOUT(AVE)
Not switching
Figure 20. PWM Switching Timing Diagram
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
Figure 21. SLLMTM Switching Timing Diagram
8/21
TSZ02201-0J3J0AJ00130-1-2
02.Oct.2014 Rev.002
BD9130NV
2. Description of Functions
(1) Soft-Start Function
During start-up, the soft-start circuit gradually establishes the output voltage to limit the input current. This prevents the
overshoot in the output voltage and inrush current.
(2) Shutdown Function
When EN terminal is “Low”, the device operate in Standby Mode, and all the functional blocks such as reference
voltage circuit, internal oscillator and drivers are turned OFF. Standby current is 0μA (Typ).
(3) UVLO Function
This circuit detects whether the supplied input voltage is sufficient to obtain the output voltage of this IC. It provides a
hysteresis of 50mV (Typ) to prevent the output from chattering.
Hysteresis 50mV
VCC
EN
VOUT
tSS
tSS
tSS
Soft start
Standby mode
Standby
mode
Operating mode
Standby
mode
Operating mode
UVLO
UVLO
Operating mode
EN
Standby mode
UVLO
Figure 22. Soft-Start, Shutdown, UVLO Timing Chart
(4) Short-Circuit Protection with Time Delay Function
To protect the IC from breakdown, the short-circuit turns the output OFF when the internal current limiter is activated
continuously for a fixed time (tLATCH) or more. The output that is kept OFF may be turned ON again by restarting EN or
by resetting UVLO.
EN
Output OFF
Latch
Output Short circuit
Threshold Voltage
VOUT
IL Limit
IL
t1 IRMSMax
When VCC is twice VOUT , IRMS=
Figure 30. Input Capacitor
IOUT
2
If VCC=3.3V, VOUT=1.8V, and IOUTMax=2A, (BD9130NV)
I RMS 2
1.83.3 1.8
0.99
3.3
ARMS
A low ESR 22μF/10V ceramic capacitor is recommended to reduce ESR dissipation of input capacitor for better efficiency.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
13/21
TSZ02201-0J3J0AJ00130-1-2
02.Oct.2014 Rev.002
BD9130NV
(4) Calculating RITH, CITH for Phase Compensation
Since the Current Mode Control is designed to limit an inductor current, a pole (phase lag) appears in the low frequency
area due to a CR filter consisting of an output capacitor and a load resistance, while a zero (phase lead) appears in the
high frequency area due to the output capacitor and its ESR. Therefore, the phases are easily compensated by adding
a zero to the power amplifier output with C and R as described below to cancel a pole at the power amplifier.
fp
fp(Min)
A
f Z ESR
fp(Max)
Gain
[dB]
1
2 RO CO
0
1
2 ESR CO
fZ(ESR)
IOUTMin
Phase
[deg]
IOUTMax
Pole at power amplifier
When the output current decreases, the load resistance Ro
increases and the pole frequency decreases.
0
-90
Figure 31. Open loop gain characteristics
A
fpMin
1
2 ROMax CO
Hz
← with lighter load
fpMax
1
Hz
← with heavier load
2 ROMin CO
fZ(Amp)
Zero at power amplifier
Increasing capacitance of the output capacitor lowers the
pole frequency while the zero frequency does not change.
(This is because when the capacitance is doubled, the
capacitor ESR is reduced to half.)
Gain
[dB]
0
0
Phase
[deg]
-90
f Z Amp
1
2 RITH CITH
Figure 32. Error amp phase compensation characteristics
CIN
VCC
EN
VOUT
VCC,PVCC
L
SW
VOUT
ITH
VOUT
ESR
GND,PGND
RO
CO
RITH
CITH
Figure 33. Typical Application
Stable feedback loop can be achieved by canceling the pole fp (Min) produced by the output capacitor and the load
resistance with CR zero correction by the error amplifier.
f Z Amp f P Min
1
1
2 R ITH C ITH
2 ROMax C o
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
14/21
TSZ02201-0J3J0AJ00130-1-2
02.Oct.2014 Rev.002
BD9130NV
(5) Setting the Output Voltage
The output voltage VOUT is determined by the equation (6):
VOUT ( R2 / R1 1) V ADJ
L
・・・(6)
6
Output
SW
Where:
VADJ is the Voltage at ADJ terminal (0.8V Typ)
Co
R2
1
ADJ
R1
The required output voltage may be determined by adjusting R1 and R2.
Figure 34. Setting the Output Voltage
Adjustable output voltage range : 1.0V to 2.5V
Use 1 kΩ to 100 kΩ resistor for R1. If a resistor with resistance higher than 100 kΩ is used, check the circuit and
calculate carefully for ripple voltage etc.
3.9
The lower limit of input voltage depends on the output voltage.
Basically, it is recommended to use the condition:
Input Voltage: VCC [V]
3.7
CC[V]
V CC
IN PUT VOLTA GE :V
[V]
VCC Min VOUT 1.3V
Figure 35. shows the necessary output current value at the
lower limit of input voltage. (DCR of inductor: 0.1Ω)
This data is the characteristic value, so it does not guarantee
the operation range.
3.5
3.3
Vo=2.5V
Vo=1.8V
3.1
Vo=2.0V
2.9
2.7
0
0.5
1
1.5
2
Output
Current: :IIOUT
[A]
OUT
PUT CURRENT
IOUT
[A]
OUT[A]
Figure 35. Minimum Input Voltage in each Output Voltage
7. Cautions on PCB Layout
VCC
R2
1
2
R1
3
RITH
③
CITH
EN 8
ADJ
VCC
PVCC
ITH
SW
7
GND
PGND
①
L
6
5
4
EN
VOUT
CIN
②
CO
GND
Figure 36. Layout Diagram
①
②
③
For the sections drawn with heavy line, use thick conductor pattern as short as possible.
Layout the input ceramic capacitor CIN closer to the pins PVCC and PGND, and the output capacitor CO closer to
the pin PGND.
Layout CITH and RITH between the pins ITH and GND as near as possible with least necessary wiring.
Note: SON008V5060 (BD9130NV) has thermal FIN on the reverse of the package.
The package thermal performance may be enhanced by bonding the FIN to GND plane which occupies a large area
of PCB.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
15/21
TSZ02201-0J3J0AJ00130-1-2
02.Oct.2014 Rev.002
BD9130NV
8. Recommended Components Lists on Above Application
Symbol
Part
Value
Manufacturer
Series
Coil
2.2µH
TDK
LTF5022-2R2N3R2
CIN
Ceramic capacitor
22µF
Kyocera
CM32X5R226M10A
CO
Ceramic capacitor
22µF
Kyocera
CM316B226M06A
Murata
Murata
Murata
Murata
Murata
Rohm
Rohm
Rohm
Rohm
Rohm
GRM18 Series
GRM18 Series
GRM18 Series
GRM18 Series
GRM18 Series
MCR03 Series
MCR03 Series
MCR03 Series
MCR03 Series
MCR03 Series
L
CITH
Ceramic capacitor
RITH
Resistance
VOUT=1.0V
VOUT=1.2V
VOUT=1.5V
VOUT=1.8V
VOUT=2.5V
VOUT=1.0V
VOUT=1.2V
VOUT=1.5V
VOUT=1.8V
VOUT=2.5V
680pF
560pF
470pF
330pF
330pF
10kΩ
12kΩ
15kΩ
18kΩ
18kΩ
Note:The parts list presented above is an example of recommended parts. Although the parts are standard, actual circuit characteristics should be checked
on your application carefully before use. Be sure to allow sufficient margins to accommodate variations between external devices and this IC when
employing the depicted circuit with other circuit constants modified. Both static and transient characteristics should be considered in establishing these
margins. When switching noise is significant and may affect the system, a low pass filter should be inserted between the VCC and PVCC pins, and a
Schottky Barrier diode connected between the SW and PGND pins.
I/O Equivalent Circuit
・EN pin
PVCC
・SW pin
PVCC
PVCC
EN
SW
・ADJ pin
・ITH pin
VCC
ADJ
ITH
Figure 37. I/O Equivalent Circuit
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
16/21
TSZ02201-0J3J0AJ00130-1-2
02.Oct.2014 Rev.002
BD9130NV
Operational Notes
1.
Reverse Connection of Power Supply
Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when
connecting the power supply, such as mounting an external diode between the power supply and the IC’s power
supply pins.
2.
Power Supply Lines
Design the PCB layout pattern to provide low impedance supply lines. Separate the ground and supply lines of the
digital and analog blocks to prevent noise in the ground and supply lines of the digital block from affecting the analog
block. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and
aging on the capacitance value when using electrolytic capacitors.
3.
Ground Voltage
Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition.
4.
Ground Wiring Pattern
When using both small-signal and large-current ground traces, the two ground traces should be routed separately but
connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal
ground caused by large currents. Also ensure that the ground traces of external components do not cause variations
on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance.
5.
Thermal Consideration
Should by any chance the power dissipation rating be exceeded the rise in temperature of the chip may result in
deterioration of the properties of the chip. In case of exceeding this absolute maximum rating, increase the board size
and copper area to prevent exceeding the Pd rating.
6.
Recommended Operating Conditions
These conditions represent a range within which the expected characteristics of the IC can be approximately
obtained. The electrical characteristics are guaranteed under the conditions of each parameter.
7.
Inrush Current
When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush
current may flow instantaneously due to the internal powering sequence and delays, especially if the IC
has more than one power supply. Therefore, give special consideration to power coupling capacitance,
power wiring, width of ground wiring, and routing of connections.
8.
Operation Under Strong Electromagnetic Field
Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction.
9.
Testing on Application Boards
When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may
subject the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply
should always be turned off completely before connecting or removing it from the test setup during the inspection
process. To prevent damage from static discharge, ground the IC during assembly and use similar precautions during
transport and storage.
10. Inter-pin Short and Mounting Errors
Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in
damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin.
Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment)
and unintentional solder bridge deposited in between pins during assembly to name a few.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
17/21
TSZ02201-0J3J0AJ00130-1-2
02.Oct.2014 Rev.002
BD9130NV
Operational Notes – continued
11. Unused Input Pins
Input pins of an IC are often connected to the gate of a MOS transistor. The gate has extremely high impedance and
extremely low capacitance. If left unconnected, the electric field from the outside can easily charge it. The small
charge acquired in this way is enough to produce a significant effect on the conduction through the transistor and
cause unexpected operation of the IC. So unless otherwise specified, unused input pins should be connected to the
power supply or ground line.
12. Regarding the Input Pin of the IC
This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them
isolated. P-N junctions are formed at the intersection of the P layers with the N layers of other elements, creating a
parasitic diode or transistor. For example (refer to figure below):
When GND > Pin A and GND > Pin B, the P-N junction operates as a parasitic diode.
When GND > Pin B, the P-N junction operates as a parasitic transistor.
Parasitic diodes inevitably occur in the structure of the IC. The operation of parasitic diodes can result in mutual
interference among circuits, operational faults, or physical damage. Therefore, conditions that cause these diodes to
operate, such as applying a voltage lower than the GND voltage to an input pin (and thus to the P substrate) should
be avoided.
Resistor
Transistor (NPN)
Pin A
Pin B
C
E
Pin A
N
P+
P
N
N
P+
N
Pin B
B
Parasitic
Elements
N
P+
N P
N
P+
B
N
C
E
Parasitic
Elements
P Substrate
P Substrate
GND
GND
Parasitic
Elements
GND
Parasitic
Elements
GND
N Region
close-by
Figure 38. Example of monolithic IC structure
13. Thermal Shutdown Circuit(TSD)
This IC has a built-in thermal shutdown circuit that prevents heat damage to the IC. Normal operation should always
be within the IC’s power dissipation rating. If however the rating is exceeded for a continued period, the junction
temperature (Tj) will rise which will activate the TSD circuit that will turn OFF all output pins. When the Tj falls below
the TSD threshold, the circuits are automatically restored to normal operation.
Note that the TSD circuit operates in a situation that exceeds the absolute maximum ratings and therefore, under no
circumstances, should the TSD circuit be used in a set design or for any purpose other than protecting the IC from
heat damage.
14. Selection of Inductor
It is recommended to use an inductor with a series resistance element (DCR) 0.1Ω or less. Especially, note that use
of a high DCR inductor will cause an inductor loss, resulting in decreased output voltage. Should this condition
continue for a specified period (soft start time + timer latch time), output short circuit protection will be activated and
output will be latched OFF. When using an inductor over 0.1Ω, be careful to ensure adequate margins for variation
between external devices and this IC, including transient as well as static characteristics. Furthermore, in any case, it
is recommended to start up the output with EN after supply voltage is within.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
18/21
TSZ02201-0J3J0AJ00130-1-2
02.Oct.2014 Rev.002
BD9130NV
Ordering Information
B
D
9
1
3
0
Part Number
N
V
-
Package
NV:SON008V5060
E2
Packaging and forming specification
E2: Embossed tape and reel
Marking Diagram
SON008V5060 (TOP VIEW)
Part Number Marking
BD9130
LOT Number
1PIN MARK
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
19/21
TSZ02201-0J3J0AJ00130-1-2
02.Oct.2014 Rev.002
BD9130NV
Physical Dimension, Tape and Reel Information
Package Name
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
SON008V5060
20/21
TSZ02201-0J3J0AJ00130-1-2
02.Oct.2014 Rev.002
BD9130NV
Revision History
Date
Revision
02.Mar.2012
02.Oct.2014
001
002
Changes
New Release
Applied the ROHM Standard Style and improved understandability.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
21/21
TSZ02201-0J3J0AJ00130-1-2
02.Oct.2014 Rev.002
Notice
Precaution on using ROHM Products
1.
Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment,
OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you
(Note 1)
intend to use our Products in devices requiring extremely high reliability (such as medical equipment
, transport
equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car
accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or
serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.
Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any
damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific
Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU
CHINA
CLASSⅢ
CLASSⅡb
CLASSⅢ
CLASSⅢ
CLASSⅣ
CLASSⅢ
2.
ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3.
Our Products are designed and manufactured for use under standard conditions and not under any special or
extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any
special or extraordinary environments or conditions. If you intend to use our Products under any special or
extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of
product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4.
The Products are not subject to radiation-proof design.
5.
Please verify and confirm characteristics of the final or mounted products in using the Products.
6.
In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7.
De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual
ambient temperature.
8.
Confirm that operation temperature is within the specified range described in the product specification.
9.
ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1.
When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2.
In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice – GE
© 2014 ROHM Co., Ltd. All rights reserved.
Rev.003
Precautions Regarding Application Examples and External Circuits
1.
If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2.
You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1.
Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2.
Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3.
Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4.
Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
QR code printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act,
please consult with ROHM representative in case of export.
Precaution Regarding Intellectual Property Rights
1.
All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable
for infringement of any intellectual property rights or other damages arising from use of such information or data.:
2.
No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the information contained in this document.
Other Precaution
1.
This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2.
The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3.
In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4.
The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice – GE
© 2014 ROHM Co., Ltd. All rights reserved.
Rev.003
Datasheet
General Precaution
1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.
ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s
representative.
3.
The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or
liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or
concerning such information.
Notice – WE
© 2014 ROHM Co., Ltd. All rights reserved.
Rev.001
工商网监
湘ICP备2023018690号
