BD9161FVM-LBTR

Datasheet 2.5V to 4.5V, Input 0.6A Integrated FET 1ch Synchronous Buck Converter BD9161FVM-LB General Description Key Specifications „ „ „ „ „ „ „ „ This is the product guarantees long time support in Industrial market. ROHM’s high efficiency step-down switching regulator BD9161FVM-LB is a power supply designed to produce 1.2volts (low voltage) from 3.3volts power supply line. Offers high efficiency with our original pulse skip control technology and synchronous rectifier. Employs a current mode control system to provide faster transient response to sudden change in load. Input Voltage Range: Output Voltage Range: Output Current: Switching Frequency: Pch FET On Resistance: Nch FET On Resistance: Standby Current: Operating Temperature Range: Package 2.5V to 4.5V 1.0V to 3.3V 0.6A(Max) 1MHz(Typ) 0.35Ω(Typ) 0.37Ω(Typ) 0μA (Typ) -25°C to +85°C W(Typ) x D(Typ) x H(Max) 2.90mm x4.00mm x 0.90mm MSOP8 Features „ „ „ „ „ „ „ „ Long Time Support Product for Industrial Applications. Fast Transient Response with Current Mode PWM Control System. Highly Efficiency with Synchronous Rectifier. (Nch/Pch FET) 100% Duty Ratio. Soft-Start Function. Thermal Protection and ULVO Functions. Short-Current Protection Circuit with Time Delay Function. Shutdown Function. Applications MSOP8 „ Industrial Equipment „ Power Supply for HDD, DVD and CPU, ASIC „ Secondary Power Supply Typical Application Circuit VCC Cin L VCC,PVCC EN SW VOUT CO ITH GND,PGND ADJ RITH CITH Figure 1. Typical Application Circuit 〇Product structure : Silicon monolithic integrated circuit .www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 • 14 • 001 〇This product has no designed protection against radioactive rays 1/20 TSZ02201-0J4J0AJ00580-1-2 21.Feb.2014 Rev.002 BD9161FVM-LB Pin Configuration (TOP VIEW) Figure 2. Pin Configuration Pin Description Pin No. Pin Name 1 ADJ Output voltage Feedback pin (Adjustable) 2 ITH GmAmp output pin/Connected phase compensation capacitor 3 EN Enable pin (Active High) 4 GND 5 PGND 6 SW 7 PVCC 8 VCC Function Ground Nch FET source pin Pch/Nch FET drain output pin Pch FET source pin VCC power supply input pin Block Diagram Enable EN 3 VCC 8 VREF 7 PVCC Current Comp. R Q Gm Amp. S SLOPE VCC Current Sense/ Protect Output CLK + SW Driver Logic ADJ 2 PGND 5 TSD 4 SCP 1 6 OSC UVLO Soft Start 3.3V Input GND ITH Figure 3. Block Diagram www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 2/20 TSZ02201-0J4J0AJ00580-1-2 21.Feb.2014 Rev.002 BD9161FVM-LB Description of Block BD9161FVM-LB is a synchronous rectifying step-down switching regulator that achieves faster transient response by employing current mode PWM control system. It utilizes switching operation in PWM (Pulse Width Modulation) mode for TM heavier load, while it utilizes SLLM (Simple Light Load Mode) operation for lighter load to improve efficiency. ○Current mode PWM control Synthesizes a PWM control signal with a inductor current feedback loop added to the voltage feedback. ・PWM (Pulse Width Modulation) control The oscillation frequency for PWM is 1 MHz. SET signal form OSC turns ON a P-channel MOS FET (while a N-channel MOS FET is turned OFF), and an inductor current I L increases. The current comparator (Current Comp) receives two signals, a current feedback control signal (SENSE: Voltage converted from I L) and a voltage feedback control signal (FB), and issues a RESET signal if both input signals are identical to each other, and turns OFF the P-channel MOS FET (while a N-channel MOS FET is turned ON) for the rest of the fixed period. The PWM control repeats this operation. Offers fast transient response with current mode control system. BD9161FVM-LB (Load response IO=250mA→500mA) Conventional product (VOUT of which is 2.5 volts) VOUT VOUT 40mV 98mV IOUT IOUT Voltage drop due to sudden change in load was reduced by about 50%. Figure 4. Comparison of transient response TM ・SLLM (Simple Light Load Mode) control When the control mode is shifted from PWM for heavier load to the one for lighter load or vise versa, the switching pulse is designed to turn OFF with the device held operated in normal PWM control loop, which allows linear operation without voltage drop or deterioration in transient response during the mode switching from light load to heavy load or vise versa. Although the PWM control loop continues to operate with a SET signal from OSC and a RESET signal from Current Comp, it is so designed that the RESET signal is held issued if shifted to the light load mode, with which the switching is tuned OFF and the switching pulses are thinned out under control. Activating the switching intermittently reduces the switching dissipation and improves the efficiency. Efficiency η[%] 100 SLLMTM ② 50 ① PWM ①inprovement by SLLMTM system ②improvement by synchronous rectifier 0 0.001 0.01 0.1 Output current IO[A] 1 Figure 5. Efficiency www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 3/20 TSZ02201-0J4J0AJ00580-1-2 21.Feb.2014 Rev.002 BD9161FVM-LB Description of Block - continued ・100% Duty control Max duty is 100%. (@ Pch MOS FET always ON) In usual PWM control, in case output voltage cannot keep (ex, drop of input voltage), oscillation frequency becomes lower and finally it becomes 100% duty. The output voltage is a value that depends only by on a voltage hang from the input voltage to Pch MOS FET, and can keep the output voltage even with the low input voltage. SENSE Current Comp VOUT RESET Level Shift FB SET Gm Amp. ITH R Q S IL Driver Logic VOUT SW Load OSC Figure 6. Diagram of current mode PWM control PVCC Current Comp SENSE PVCC SENSE Current Comp FB FB SET GND SET GND RESET GND RESET GND SW GND SW IL GND IL(AVE) IL 0A VOUT VOUT VOUT(AVE) VOUT(AVE) Not switching TM Figure 7. PWM switching timing chart www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 Figure 8. SLLM 4/20 switching timing chart TSZ02201-0J4J0AJ00580-1-2 21.Feb.2014 Rev.002 BD9161FVM-LB Description of Operations - continued ・Soft-start function EN terminal shifted to “High” activates a soft-starter to gradually establish the output voltage with the current limited during startup, by which it is possible to prevent an overshoot of output voltage and an inrush current. ・Shutdown function With EN terminal shifted to “Low”, the device turns to Standby Mode, and all the function blocks including reference voltage circuit, internal oscillator and drivers are turned to OFF. Circuit current during standby is 0μF (Typ). ・UVLO function Detects whether the input voltage sufficient to secure the output voltage of this IC is supplied. of 50mV (Typ) is provided to prevent output chattering. And the hysteresis width Hysteresis 50mV VCC EN VOUT Tss Tss Tss Soft start Standby mode Operating mode Standby mode Standby mode Operating mode UVLO UVLO Operating mode EN Standby mode UVLO Figure 9. Soft start, Shutdown, UVLO timing chart ・Short-current protection circuit with time delay function Turns OFF the output to protect the IC from breakdown when the incorporated current limiter is activated continuously for the fixed time (TLATCH) or more. The output thus held tuned OFF may be recovered by restarting EN or by re-unlocking UVLO. EN Output OFF latch VOUT Limit IL 1msec Standby mode Standby mode Operating mode EN Timer latch Operating mode EN Figure 10. Short-current protection circuit with time delay timing chart www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 5/20 TSZ02201-0J4J0AJ00580-1-2 21.Feb.2014 Rev.002 BD9161FVM-LB Absolute Maximum Ratings(Ta=25°C) Parameter VCC Voltage Symbol Rating VCC PVCC Voltage PVCC EN Voltage SW, ITH Voltage Unit -0.3 to +7 (Note 1) V -0.3 to +7 (Note 1) V EN -0.3 to +7 V SW,ITH -0.3 to +7 V Power Dissipation 1 Pd1 387.5 (Note 2) Power Dissipation 2 Pd2 587.4 (Note 3) Operating Temperature Range Topr -25 to +85 °C Storage Temperature Range Tstg -55 to +150 °C Tjmax +150 °C EN Voltage mW mW (Note 1) Pd should not be exceeded. (Note 2) Derating in done 3.1mW/°C for temperatures above Ta=25°C (Note 3) Derating in done 4.7mW/°C for temperatures above Ta=25°C,Mounted on 70mm×70mm×1.6mm Glass Epoxy PCB. Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated over the absolute maximum ratings. Recommended Operating Conditions(Ta=25°C) Parameter VCC Voltage Symbol Min Typ Max Unit 2.5 3.3 4.5 V 2.5 3.3 4.5 V EN 0 - VCC V SW,ITH 1.0 - 3.3 V - - 0.6 A (Note 4) VCC PVCC Voltage PVCC EN Voltage Output Voltage Setting Range SW, ITH Average Output Current ISW (Note 4) (Note 4) (Note 4) Pd should not be exceeded. Electrical Characteristics(Unless otherwise specified Ta=25°C VCC=PVCC=3.3V EN=VCC) Parameter Standby Supply Current Symbol Min Typ Max Unit ISTB - 0 10 μA Conditions EN=GND ICC - 200 400 μA EN Low Voltage VENL - GND 0.8 V Standby mode EN High Voltage VENH 2.0 VCC - V Active mode EN Input Current IEN - 1 10 μA VEN=3.3V FOSC 0.8 1 1.2 MHz Pch FET ON Resistance RONP - 0.35 0.6 Ω PVCC=3.3V Nch FET ON Resistance RONN - 0.37 0.68 Ω PVCC=3.3V Output Voltage VOUT 0.784 0.8 0.816 V ITH SInk Current ITHSI 10 20 - μA VOUT =H ITH Source Current ITHSO 10 20 - μA VOUT =L Operating Supply Current Switching Frequency UVLO Threshold Voltage VUVLO1 2.2 2.3 2.4 V VCC=H→L UVLO Hysteresis Voltage V UVLO2 2.22 2.35 2.5 V VCC=L→H Soft Start Time Timer Latch Time Output Short Circuit Threshold Voltage www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 TSS 0.5 1 2 ms TLATCH 1 2 3 ms VSCP - 0.4 0.56 V 6/20 SCP/TSD operated VOUT =H→L TSZ02201-0J4J0AJ00580-1-2 21.Feb.2014 Rev.002 BD9161FVM-LB Typical Performance Curves Figure 11. VOUT VS Vcc Figure 12. VOUT VS VEN Figure 13. VOUT VS IOUT www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 Figure 14. VOUT VS Ta 7/20 TSZ02201-0J4J0AJ00580-1-2 21.Feb.2014 Rev.002 BD9161FVM-LB Typical Performance Curves - continued Figure 15. Efficiency Figure 16. fosc VS Ta Figure 17. RON VS Ta www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 Figure 18.VEN VS Ta 8/20 TSZ02201-0J4J0AJ00580-1-2 21.Feb.2014 Rev.002 BD9161FVM-LB Typical Performance Curves - continued Figure 19. fosc VS VCC Figure 20. Soft start waveform Figure 21. SW waveform IO=10mA www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 Figure 22. SW waveform IO=500mA 9/20 TSZ02201-0J4J0AJ00580-1-2 21.Feb.2014 Rev.002 BD9161FVM-LB Typical Performance Curves - continued Figure 23. SW waveform IO=600mA Figure 24. Transient response IO=250mA→500mA(10μs) Figure 25. Transient response IO=500mA→250mA(10μs) www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 10/20 TSZ02201-0J4J0AJ00580-1-2 21.Feb.2014 Rev.002 BD9161FVM-LB Application Example Figure 26. PCB layout ① For the sections drawn with heavy line, use thick conductor pattern as short as possible. ② Lay out the input ceramic capacitor CIN closer to the pins PVCC and PGND, and the output capacitor CO closer to the pin PGND. ③ Lay out CITH and RITH between the pins ITH and GND as neat as possible with least necessary wiring. Recommended Component Lists With Above Applications Symbol Type Value L RIN CIN CO Coil Resistance Ceramic capacitor Ceramic capacitor CITH Ceramic capacitor RITH Resistance 4.7μH 10Ω 10μF 10μF VOUT=1.0V VOUT=1.2V VOUT=1.5V VOUT=1.8V VOUT=2.5V VOUT=1.0V VOUT=1.2V VOUT=1.5V VOUT=1.8V VOUT=2.5V 820pF 560pF 470pF 470pF 330pF 6.8kΩ 8.2Ω 12kΩ 12kΩ 15kΩ Manufacturer TDK Sumida ROHM Kyocera Kyocera murata murata murata murata murata Rohm Rohm Rohm Rohm Rohm Part Number VLF5014AT-4R7M1R1 CMD6D11B MCR03 Series CM316X5R106K10A CM316X5R106K10A GRM18 Series GRM18 Series GRM18 Series GRM18 Series GRM18 Series MCR03 Series MCR03 Series MCR03 Series MCR03 Series MCR03 Series The parts list presented above is an example of recommended parts. Although the parts are sound, actual circuit characteristics should be checked on your application carefully before use. Be sure to allow sufficient margins to accommodate variations between external devices and this IC when employing the depicted circuit with other circuit constants modified. Both static and transient characteristics should be considered in establishing these margins. When switching noise is substantial and may impact the system, a low pass filter should be inserted between the V CC and PVCC pins, and a schottky barrier diode established between the SW and PGND pins. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 11/20 TSZ02201-0J4J0AJ00580-1-2 21.Feb.2014 Rev.002 BD9161FVM-LB Selection of Components Externally Connected 1. Selection of inductor (L) IL The inductance significantly depends on output ripple current. As seen in the equation (1), the ripple current decreases as the inductor and/or switching frequency increases. ΔIL ΔIL= VCC (VCC-VOUT)×VOUT [A]・・・(1) L×VCC×f Appropriate ripple current at output should be 20 to 30% more or less of the maximum output current. IL ΔIL=0.25×IOUTmax [A]・・・(2) VOUT L (VCC-VOUT)×VOUT CO L= [H]・・・(3) ΔIL×VCC×f (ΔIL: Output ripple current, and f: Switching frequency) Figure 27. Output ripple current Current exceeding the current rating of the inductor results in magnetic saturation of the inductor, which decreases efficiency. The inductor must be selected allowing sufficient margin with which the peak current may not exceed its current rating. If VCC=3.3V, VOUT=2.5V, f=1MHz, ΔIL=0.25×0.6A=0.15A (3.3-2.5)×2.5 L ≥ 0.15×3.3×1M ≥ 4.04μ Select the inductor of low resistance component (such as DCR and ACR) to minimize dissipation in the inductor for better efficiency. 2. Selection of output capacitor (CO) Output capacitor should be selected with the consideration on the stability region and the equivalent series resistance required to smooth ripple voltage. Output ripple voltage is determined by the equation (4)： VCC VOUT L ΔVOUT=ΔIL×ESR [V]・・・(4) ESR (ΔIL: Output ripple current, ESR: Equivalent series resistance of output capacitor) CO *Rating of the capacitor should be determined allowing sufficient margin against output voltage. Less ESR allows reduction in output ripple voltage. Figure 28. Output capacitor Inappropriate capacitance may cause problem in startup. A 10μF to 100μF ceramic capacitor is recommended. 3. Selection of input capacitor (Cin) VCC Input capacitor to select must be a low ESR capacitor of the capacitance sufficient to cope with high ripple current to prevent high transient voltage. The ripple current IRMS is given by the equation (5): Cin VOUT L CO IRMS=IOUT× √VOUT (VCC-VOUT) VCC [A]・・・(5) < Worst case > IRMS(max) When VCC is twice the VOUT, IRMS= Figure 29. Input capacitor IOUT 2 If VCC=3.3V, VOUT=2.5V, IOUTmax=0.6A √2.5(3.3-2.5) IRMS=0.6× =0.284 [ARMS] 5 A low ESR 10μF/10V ceramic capacitor is recommended to reduce ESR dissipation of input capacitor for better efficiency. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 12/20 TSZ02201-0J4J0AJ00580-1-2 21.Feb.2014 Rev.002 BD9161FVM-LB 4. Determination of RITH, CITH that works as a phase compensator As the Current Mode Control is designed to limit a inductor current, a pole (phase lag) appears in the low frequency area due to a CR filter consisting of a output capacitor and a load resistance, while a zero (phase lead) appears in the high frequency area due to the output capacitor and its ESR. So, the phases are easily compensated by adding a zero to the power amplifier output with C and R as described below to cancel a pole at the power amplifier. fp(Min) 1 2π×RO×CO 1 fz(ESR)= 2π×ESR×CO fp= A fp(Max) Gain [dB] 0 fz(ESR) IOUTMin Phase [deg] IOUTMax Pole at power amplifier When the output current decreases, the load resistance Ro increases and the pole frequency lowers. 0 -90 fp(Min)= 1 2π×ROMax×CO [Hz]←with lighter load fp(Max)= 1 2π×ROMin×CO [Hz]←with heavier load Figure 30. Open loop gain characteristics A fz(Amp) Zero at power amplifier Increasing capacitance of the output capacitor lowers the pole frequency while the zero frequency does not change. (This is because when the capacitance is doubled, the capacitor ESR reduces to half.) Gain [dB] 0 0 Phase [deg] fz(Amp)= -90 1 2π×RITH×CITH Figure 31. Error amp phase compensation characteristics VCC Cin EN VOUT L VCC,PVCC SW VOUT ITH VOUT ESR RO CO GND,PGND RITH CITH Figure 32. Typical application Stable feedback loop may be achieved by canceling the pole fp (Min) produced by the output capacitor and the load resistance with CR zero correction by the error amplifier. fz(Amp)= fp(Min) 1 2π×RITH×CITH = 1 2π×ROMax×CO 5. Determination of output voltage The output voltage VOUT is determined by the equation (6): VOUT=(R2/R1+1)×VADJ・・・(6) VADJ: Voltage at ADJ terminal (0.8V Typ) With R1 and R2 adjusted, the output voltage may be determined as required. (Adjustable output voltage range：1.0V to 3.3V ) L SW ADJ Output CO R2 R1 Use 1 kΩ to 100 kΩ resistor for R1. If a resistor of the resistance higher than 100 kΩ is used, check the assembled set carefully for ripple voltage etc. Figure 33. Determination of output voltage www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 13/20 TSZ02201-0J4J0AJ00580-1-2 21.Feb.2014 Rev.002 BD9161FVM-LB Switching Regulator Efficiency Efficiency ŋ may be expressed by the equation shown below: VOUT×IOUT POUT POUT ×100[%]= ×100[%]= ×100[%] η= Vin×Iin Pin POUT+PDα Efficiency may be improved by reducing the switching regulator power dissipation factors PDα as follows: Dissipation factors: 2 1) ON resistance dissipation of inductor and FET：PD(I R) 2) Gate charge/discharge dissipation：PD(Gate) 3) Switching dissipation：PD(SW) 4) ESR dissipation of capacitor：PD(ESR) 5) Operating current dissipation of IC：PD(IC) 2 2 1) PD(I R)=IOUT ×(RCOIL+RON) (RCOIL [Ω]：DC resistance of inductor, RON [Ω]：ON resistance of FET IOUT [A]：Output current.) 2)PD(Gate)=Cgs×f×V (Cgs[F]：Gate capacitance of FET, f[H]：Switching frequency, V[V]：Gate driving voltage of FET) 2 Vin ×CRSS×IOUT×f 3)PD(SW)= (CRSS[F]：Reverse transfer capacitance of FET, IDRIVE[A]：Peak current of gate.) IDRIVE 2 4)PD(ESR)= IRMS ×ESR (IRMS [A]：Ripple current of capacitor, ESR[Ω]：Equivalent series resistance.) 5)PD(IC)= Vin×ICC (ICC [A]：Circuit current.) Power Dissipation As this IC functions with high efficiency without significant heat generation in most applications, no special consideration is needed on permissible dissipation or heat generation. In case of extreme conditions, however, including lower input voltage, higher output voltage, heavier load, and/or higher temperature, the permissible dissipation and/or heat generation must be carefully considered. For dissipation, only conduction losses due to DC resistance of inductor and ON resistance of FET are considered. Because the conduction losses are considered to play the leading role among other dissipation mentioned above including gate charge/discharge dissipation and switching dissipation. Power dissipation:Pd [mW] 1000 800 600 400 2 P=IOUT ×(RON) RON=D×RONP+(1-D)×RONN ①Using an IC alone θja=322.6°C/W ②mounted on glass epoxy PCB θja=212.8°C/W D：ON duty (=VOUT/VCC) RONP：ON resistance of P-channel MOS FET RONN：ON resistance of N-channel MOS FET IOUT：Output current ②587.4mW ①387.5mW 200 0 0 25 50 75 85 100 125 150 Ambient temperature:Ta [°C] Figure 34. Thermal derating curve (MSOP8) If VCC=3.3V, VOUT=2.5V, RONP=0.35Ω, RONN=0.37Ω, IOUT=0.6A, for example, D=VOUT/VCC=2.5/3.3=0.758 RON=0.758×0.35+(1-0.758)×0.37 =0.2653+0.08954 =0.35484[Ω] 2 P=0.6 ×0.35484≒127.7[mV] As RONP is greater than RONN in this IC, the dissipation increases as the ON duty becomes greater. With the consideration on the dissipation as above, thermal design must be carried out with sufficient margin allowed. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 14/20 TSZ02201-0J4J0AJ00580-1-2 21.Feb.2014 Rev.002 BD9161FVM-LB I/O equivalence circuit PVCC ・SW pin ・EN pin PVCC PVCC 10kΩ EN SW ・ITH pin ・ADJ pin VCC 10kΩ ADJ ITH Figure 35. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 I/O equivalence circuit 15/20 TSZ02201-0J4J0AJ00580-1-2 21.Feb.2014 Rev.002 BD9161FVM-LB Operational Notes 1. Reverse Connection of Power Supply Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when connecting the power supply, such as mounting an external diode between the power supply and the IC’s power supply pins. 2. Power Supply Lines Design the PCB layout pattern to provide low impedance supply lines. Separate the ground and supply lines of the digital and analog blocks to prevent noise in the ground and supply lines of the digital block from affecting the analog block. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and aging on the capacitance value when using electrolytic capacitors. 3. Ground Voltage Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition. 4. Ground Wiring Pattern When using both small-signal and large-current ground traces, the two ground traces should be routed separately but connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal ground caused by large currents. Also ensure that the ground traces of external components do not cause variations on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance. 5. Thermal Consideration Should by any chance the power dissipation rating be exceeded the rise in temperature of the chip may result in deterioration of the properties of the chip. The absolute maximum rating of the Pd stated in this specification is when the IC is mounted on a 70mm x 70mm x 1.6mm glass epoxy board. In case of exceeding this absolute maximum rating, increase the board size and copper area to prevent exceeding the Pd rating. 6. Recommended Operating Conditions These conditions represent a range within which the expected characteristics of the IC can be approximately obtained. The electrical characteristics are guaranteed under the conditions of each parameter. 7. Inrush Current When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush current may flow instantaneously due to the internal powering sequence and delays, especially if the IC has more than one power supply. Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and routing of connections. 8. Operation Under Strong Electromagnetic Field Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction. 9. Testing on Application Boards When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may subject the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply should always be turned off completely before connecting or removing it from the test setup during the inspection process. To prevent damage from static discharge, ground the IC during assembly and use similar precautions during transport and storage. 10. Inter-pin Short and Mounting Errors Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin. Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and unintentional solder bridge deposited in between pins during assembly to name a few. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 16/20 TSZ02201-0J4J0AJ00580-1-2 21.Feb.2014 Rev.002 BD9161FVM-LB Operational Notes – continued 11. Unused Input Pins Input pins of an IC are often connected to the gate of a MOS transistor. The gate has extremely high impedance and extremely low capacitance. If left unconnected, the electric field from the outside can easily charge it. The small charge acquired in this way is enough to produce a significant effect on the conduction through the transistor and cause unexpected operation of the IC. So unless otherwise specified, unused input pins should be connected to the power supply or ground line. 12. Regarding the Input Pin of the IC This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them isolated. P-N junctions are formed at the intersection of the P layers with the N layers of other elements, creating a parasitic diode or transistor. For example (refer to figure below): When GND > Pin A and GND > Pin B, the P-N junction operates as a parasitic diode. When GND > Pin B, the P-N junction operates as a parasitic transistor. Parasitic diodes inevitably occur in the structure of the IC. The operation of parasitic diodes can result in mutual interference among circuits, operational faults, or physical damage. Therefore, conditions that cause these diodes to operate, such as applying a voltage lower than the GND voltage to an input pin (and thus to the P substrate) should be avoided. Resistor Transistor (NPN) Pin A Pin B C E Pin A N P+ P N N P+ N Pin B B Parasitic Elements N P+ N P N P+ B N C E Parasitic Elements P Substrate P Substrate GND GND Parasitic Elements GND Parasitic Elements GND N Region close-by Figure 36. Example of monolithic IC structure 13. Ceramic Capacitor When using a ceramic capacitor, determine the dielectric constant considering the change of capacitance with temperature and the decrease in nominal capacitance due to DC bias and others. 14. Area of Safe Operation (ASO) Operate the IC such that the output voltage, output current, and power dissipation are all within the Area of Safe Operation (ASO). 15. Thermal Shutdown Circuit(TSD) This IC has a built-in thermal shutdown circuit that prevents heat damage to the IC. Normal operation should always be within the IC’s power dissipation rating. If however the rating is exceeded for a continued period, the junction temperature (Tj) will rise which will activate the TSD circuit that will turn OFF all output pins. When the Tj falls below the TSD threshold, the circuits are automatically restored to normal operation. Note that the TSD circuit operates in a situation that exceeds the absolute maximum ratings and therefore, under no circumstances, should the TSD circuit be used in a set design or for any purpose other than protecting the IC from heat damage. 16. Over Current Protection Circuit (OCP) This IC incorporates an integrated overcurrent protection circuit that is activated when the load is shorted. This protection circuit is effective in preventing damage due to sudden and unexpected incidents. However, the IC should not be used in applications characterized by continuous operation or transitioning of the protection circuit. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 17/20 TSZ02201-0J4J0AJ00580-1-2 21.Feb.2014 Rev.002 BD9161FVM-LB Ordering Information B D 9 1 6 Part Number 1 F V M Package FVM:MSOP8 - LBTR Product class LB for Industrial applications Packaging and forming specification TR: Embossed tape and reel Marking Diagrams MSOP8(TOP VIEW) Part Number Marking D 6 9 1 1 LOT Number 1PIN MARK www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 18/20 TSZ02201-0J4J0AJ00580-1-2 21.Feb.2014 Rev.002 BD9161FVM-LB Physical Dimension, Tape and Reel Information Package Name www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 MSOP8 19/20 TSZ02201-0J4J0AJ00580-1-2 21.Feb.2014 Rev.002 BD9161FVM-LB Revision History Date Revision 06.Sep.2013 21.Feb.2014 001 002 Changes New Release Delete sentence “and log life cycle” in General Description and Futures. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 20/20 TSZ02201-0J4J0AJ00580-1-2 21.Feb.2014 Rev.002 Datasheet Notice Precaution on using ROHM Products 1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅢ CLASSⅣ CLASSⅢ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice - SS © 2014 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act, please consult with ROHM representative in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable for infringement of any intellectual property rights or other damages arising from use of such information or data.: 2. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the information contained in this document. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice - SS © 2014 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s representative. 3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. Notice – WE © 2014 ROHM Co., Ltd. All rights reserved. Rev.001