ROHM Switching Regulator Solutions
Evaluation Board:
Step-down Switching Regulator
With Built-in Power MOSFET
No.0000000014
BD9328EFJ / BD9329AEFJ (12V | 2A / 3A Output)
●Introduction
This application note will provide the steps necessary to operate and evaluate ROHM’s step-down switching regulator using the
BD9328EFJ/BD9329AEFJ evaluation boards. Component selection, board layout recommendations, operation procedures and application
data is provided.
●Description
This evaluation board has been developed for ROHM’s step-down switching regulator customers evaluating BD9328EFJ and/or
BD9329AEFJ. While accepting a wide power supply of 4.2-18V, a step down output of 3.3V or any external resistor defined voltage can be
produced. The ICs have two integrated low resistance N-channel MOSFETs and a fixed synchronization frequency of 380 kHz. A Soft Start
circuit prevents in-rush current during startup along with UVLO (low voltage error prevention circuit) and TSD (thermal shutdown detection)
protection circuits. An EN pin allows for simple ON/OFF control of the IC to reduce standby current consumption.
●Applications
Distributed Power Systems
Pre-regulator for linear regulators
●Evaluation Board Operating Limits and Absolute Maximum Ratings
Limit
Parameter
Symbol
Unit
MIN
TYP
MAX
Conditions
Supply Voltage
BD9328EFJ
VCC
4.2
12
18
V
BD9329AEFJ
VCC
4.2
12
18
V
BD9328EFJ
VOUT
-
3.3V
-
V
BD9329AEFJ
VOUT
-
3.3V
-
V
BD9328EFJ
IOUT
-
-
2
A
BD9329AEFJ
IOUT
-
-
3
A
Output Voltage / Current
●Evaluation Board
Below is the evaluation board with the BD9328EFJ. BD9329AEFJ eval board uses the same components and board layout
Vout
Vin
High
E
N
Low
1
Application Note
●Evaluation Board Schematic
Below is the evaluation board schematic for BD9328EFJ. BD9329AEFJ eval board uses the same schematic
●Evaluation Board I/O
Below is the reference application circuit that shows the inputs (Vin and EN) and the output (SW and FB)
●Evaluation Board Operation Procedures
Below is the procedure to operate the evaluation board
1.
2.
3.
Connect GND to a GND pin on the evaluation board
Connect Vin to the +12V_Vin pin. This will provide Vin to the Vin pin of the IC
i. Note: EN pin is pulled high as when SW1 is high (white arrow)
Now output power can be measured from the +3.3V_Vout pin on the evaluation board with a load attached
Page 2 of 9
Application Note
●Reference Graphs Application Data for BD9328EFJ
Below graphs shows load characteristics, transient responses and efficiency of the BD9328/9 eval board.
Page 3 of 9
Application Note
●Reference Graphs Application Data for BD9329AEFJ
Below graphs shows the load characteristics, transient responses and efficiency of the BD9329AEFJ eval board.
Page 4 of 9
Application Note
●Evaluation Board Layout Guidelines
Below are the guidelines that have been followed and recommended for BD9328EFJ and BD9329AEFJ designs
Note:
For applications operating at or near maximum voltage conditions (20V max.), additional precautions regarding heat
dissipation need to be considered during board layout. The provided evaluation board is a 2-layer board meant for evaluation
purposes only. At maximum conditions, the IC’s internal thermal shutdown detection circuit will be potentially initiated and the
output disabled until the junction temperature falls. For final designs operating near these conditions, we recommend using
one of the below PCB options for better heat dissipation of the IC.
1) Use of a 4-layer PCB with internal GND planes connected to the IC GND pins
2) Use of a 2-layer PCB with a heat sink attached to the IC package
3) Use of a 2-layer PCB with a copper plane (>1oz) attached to the IC
Page 5 of 9
Application Note
Page 6 of 9
Application Note
Page 7 of 9
Application Note
●Evaluation Board BOM
Below is a table with the build of materials. Part numbers and supplier references are provided.
※
Note: In this example, the nominal resistance values of R1 and R2 were selected to set a
3.3 V output.
Page 8 of 9
Application Note
Page 9 of 9
很抱歉,暂时无法提供与“BD9328EFJ_EVK”相匹配的价格&库存,您可以联系我们找货
免费人工找货