BD95371MUV_10

1/4 STRUCTURE TYPE PRODUCT SERIES FEATURES Silicon Monolithic Integrated Circuit Step down DC/DC converter Controller IC for NOTE PC BD95371MUV ・Built in H3Reg DC/DC controller ・Switching Frequency Variable (f=200kHz～500kHz) ○ ABSOLUTE MAXIMUM RATINGS（Ta=25℃） Parameter Input Voltage 1 Input Voltage 2 Input Voltage 3 BOOT Voltage BOOT-SW Voltage HG-SW Voltage LG Voltage Output Voltage EN Input Voltage Power Dissipation 1 Power Dissipation 2 Power Dissipation 3 Power Dissipation 4 Operating Temperature Range Storage Temperature Range Maximum Junction Temperature Symbol VCC VDD VIN BOOT BOOT-SW HG-SW LG VOUT/Is+/IsEN Pd1 Pd2 Pd3 Pd4 Topr Tstg Tjmax Limit 7 ＊1＊2 7 ＊1＊2 28 ＊1＊2 35 ＊1＊2 7 ＊1＊2 7 ＊1＊2 VDD VCC 7 ＊1 0.34＊3 0.70＊4 2.20＊5 3.56＊6 -10～+100 -55～+150 +150 Unit V V V V V V V V V W W W W ℃ ℃ ℃ *1 Not to exceed Pd. *2 Instantaneous surge voltage, back electromotive force and voltage under less than 10% duty cycle. *3 Reduced by 2.7mW/℃ for each increase in Ta of 1℃ over 25℃. (when don’t mounted on a heat radiation board ) *4 Reduced by 5.6mW/℃ for increase in Ta of 1℃ over 25℃. (when mounted on a board 70.0mm×70.0mm×1.6mm 1-layer Glass-epoxy PCB, copper foil area: 10.29mm2 ) *5 Reduced by 17.6mW/℃ for increase in Ta of 1℃ over 25℃. (when mounted on a board 70.0mm×70.0mm×1.6mm 4-layer Glass-epoxy PCB, copper foil area: 10.29mm2 2,3-layer copper foil area: 5505mm2) *6 Reduced by 28.5mW/℃ for increase in Ta of 1℃ over 25℃. (when mounted on a board 70.0mm×70.0mm×1.6mm 4-layer Glass-epoxy PCB, copper foil area: 5505mm2 ) ○ OPERATING CONDITIONS（Ta=25℃） Parameter Input Voltage 1 Input Voltage 2 Input Voltage 3 BOOT Voltage SW Voltage BOOT-SW Voltage EN Input Voltage Is Input Voltage MIN ON Time Symbol VCC VDD VIN BOOT SW BOOT-SW EN Is+/IsTonmin MIN 4.5 4.5 4.5 4.5 -0.7 4.5 0 0.7 MAX 5.5 5.5 25 30 25 5.5 5.5 2.7 80 Unit V V V V V V V V ns ★ This product is not designed for protection against radioactive rays. REV. A 2/4 ○ELECTRICAL CHARACTERISTICS （unless otherwise noted, Ta=25℃ VCC=5V,VDD=5V,EN=3V,VIN=12V,VOUT=1.05V,RFS=36kΩ） Parameter Symbol MIN Standard Value TYP MAX Unit Condition [Whole Device] VCC Bias Current VCC Standby Current VIN Bias Current VIN Standby Current EN Low Voltage EN HighVoltage (Forced Continuous mode) EN HighVoltage (SLLM Mode) EN Bias Current [Under Voltage Locked Out ] VCC threshold voltage VCC hysteresis voltage 3 [H REG Control] ON Time MAX ON Time MIN OFF Time [FET Driver] HG Higher side ON resistor HG Lower side ON resistor LG Higher side ON resistor LG Lower side ON resistor [SCP] SCP strat-up Voltage SCP delay time [OVP] FB threshold voltage [Soft start] Charge current Standby voltage [Current Limit Block] Setting Current Current limit threshold [Output Voltage setting ] VOUT typical voltage Is+ Input current Is- Input current [Power Good] FB Power Good Discharge ON resistor [BOOT Diode] VF voltage Icc Iccstb Iin Iinstb VEN_low VENth_con VENth_sllm Ien Vcc_UVLO dVcc_UVLO Ton Tonmax Toffmin HGhon HGlon LGhon LGlon Vscp Tscp Vovp Iss Vss_stb Iilim Ilim REF IIs+ IIsVPGOOD Ronpgood VF GND 2.3 4.5 3.7 100 194 0.345 0.825 1 75 0.743 -1 -1 0.38 0.4 1500 0 30 0 15 4.0 160 219 3.5 490 3.0 2.0 3.0 0.5 0.420 2.5 0.900 2 10 100 0.750 0 0 0.47 50 0.5 1800 10 80 10 0.8 3.8 5.5 25 4.3 220 244 700 6.0 4.0 6.0 1.0 0.495 0.975 3 50 125 0.757 1 1 0.56 150 0.6 μA μA μA μA V V V μA V mV ns μs ns Ω Ω Ω Ω V ms V μA mV μA mV V μA μA V Ω V EN＝0Ｖ EN＝0Ｖ EN=3V VCC:Sweep up VCC:Sweep down RILIM=100kΩ Is+=1.05V Is-=1.05V IF=1mA REV. A 3/4 ○ PHYSICAL DIMENSIONS ○ Pin Number Pin Name 4.0±0.1 4.0±0.1 95371 1.0Max. Lot.No 1pin mark S 0.08 S C0.2 2.1±0.1 1 5 16 15 11 10 1.0 0.5 0.25 +0.05 -0.04 VQFN020V4040 (Unit:mm) 2.1±0.1 20 6 Pin number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 reverse PIN name SS EN/SLLM ILIM VCC FB VOUT FREQ FS IsIs+ PGND LG VDD SW HG BOOT VIN OUT PGOOD GND FIN 0.4±0.1 0.02 +0.03 -0.02 (0.22) ○ BLOCK DIAGRAM VDD VIN Please connect FIN to GND. 4 VCC 17 VIN Thermal Protection TSD 1 SS 20 GND VDD EN/SLLM 2 Reference Block BG REF×0.56 SS×0.56 FB VOUT + - UVLO SS EN SCP 2.5ms Delay + SLLM REF×1.2 FB Soft Start Block 16 BOOT 15 HG 14 VIN BG + OVP VOUT H Reg EN/UVLO REF 3 TM R S Q SLLM SLLM Driver Circuit Controller Block SW VDD 13 OUT 18 FB 5 SS REF + + ls+ + ILIM UVLO ILIM SCP TSD OVP Current Limit + 12 LG 11 PGND Is+ + FREQ 7 9 ls10 Is+ REF ×0.56 FB 19 PGOOD + - FS 8 VOUT 6 3 ILIM REV. A 4/4 ●Operation Notes 1. Absolute maximum ratings An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc., can break down the devices, thus making impossible to identify breaking mode, such as a short circuit or an open circuit. If any over rated values will expect to exceed the absolute maximum ratings, consider adding circuit protection devices, such as fuses. 2. Connecting the power supply connector backward Connecting of the power supply in reverse polarity can damage IC. Take precautions when connecting the power supply lines. An external direction diode can be added. 3. Power supply lines Design PCB layout pattern to provide low impedance GND and supply lines. To obtain a low noise ground and supply line, separate the ground section and supply lines of the digital and analog blocks. Furthermore, for all power supply terminals to ICs, connect a capacitor between the power supply and the GND terminal. When applying electrolytic capacitors in the circuit, not that capacitance characteristic values are reduced at low temperatures. 4. GND voltage The potential of GND pin must be minimum potential in all operating conditions. 5. Thermal design Use a thermal design that allows for a sufficient margin in light of the power dissipation (Pd) in actual operating conditions. 6. Inter-pin shorts and mounting errors Use caution when positioning the IC for mounting on printed circuit boards. The IC may be damaged if there is any connection error or if pins are shorted together. 7. Actions in strong electromagnetic field Use caution when using the IC in the presence of a strong electromagnetic field as doing so may cause the IC to malfunction. 8. ASO When using the IC, set the output transistor so that it does not exceed absolute maximum ratings or ASO. 9. Thermal shutdown circuit The IC incorporates a built-in thermal shutdown circuit (TSD circuit). The thermal shutdown circuit (TSD circuit) is designed only to shut the IC off to prevent thermal runaway. It is not designed to protect the IC or guarantee its operation. Do not continue to use the IC after operating this circuit or use the IC in an environment where the operation of this circuit is assumed. TSD on temperature [°C] (typ.) 175 Hysteresis temperature [°C](typ.) 15 BD95371MUV 10. Ground Wiring Pattern When using both small signal and large current GND patterns, it is recommended to isolate the two ground patterns, placing a single ground point at the ground potential of application so that the pattern wiring resistance and voltage variations caused by large currents do not cause variations in the small signal ground voltage. Be careful not to change the GND wiring pattern of any external components, either. 11. Heat sink (FIN) Since the heat sink (FIN) is connected with the Sub, short it to the GND. REV. A Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2010 ROHM Co., Ltd. All rights reserved. R1010A