BD95820F-LBE2

Datasheet EARTH LEAKAGE CURRENT DETECTOR Earth Leakage Current Detector IC BD95820F-LB BD95820N-LB General Description Key Specifications ■ ■ ■ ■ ■ This is the product guarantees long time support in Industrial market. BD95820F-LB/BD95820N-LB integrates leakage detector and amplifier. Especially, it is suitable for high sensitivity and a high-speed operation use, and since the operating temperature range is wide, it can be used for various uses. Features Operating Supply Voltage Range： Operating Temperature Range： Supply Current： Trip Voltage： Output Current(TA=-20℃)： Packages ■ Long Time Support a Product for Industrial Applications ■ Small Temperature Fluctuation and High Input Sensitivity ■ Wide Operating Temperature Range 12V to 22V -20°C to +95°C 330µA (typ) 6.1mV to 8.9mV -200µA (min) W(Typ) x D(Typ) x H(Max) 5.00mm x 6.20mm x 1.71mm 19.30mm x 10.50mm x 3.00mm SOP8 SIP8 Applications ■ Earth leakage circuit breaker ■ Earth leakage circuit relay ■ Industrial Equipment Typical Application Circuit SCR RVS COS VZ 8 7 6 OS 5 NR SC Reference voltage output block VS C1 Latch block CVS VR 1 Trip Coil IN CIN CVR GND 2 3 RIN Recommended Value Range 0.01µF ≤ COD≤ 0.1µF 0.01µF ≤ CIN≤ 0.1µF 0.01µF ≤ CVR≤ 1µF 0.01µF ≤ COS≤ 1µF 0.1µF ≤ CVS≤ 10µF 100Ω ≤ RIN≤ 5kΩ 100Ω ≤ RCT≤ 5kΩ 39kΩ ≤ RVS≤ 150kΩ 100µs ≤ tr(Note 1)≤ 20ms 100µs ≤ tf(Note 2)≤ 20ms OD 4 C COD OD RCT ZCT:Zero-phase Current Transformer ZCT:Zero current transformer TEST SW&R (Note 1) Time to change into 90% from 10% in the process when the power supply voltage rises to 12V from 0V. (Note 2) Time to change into 90% from 10% in the process when the power supply voltage falls from 12V to 0V. ○Product structure：Silicon monolithic integrated circuit ○This product has no designed protection against radioactive rays. www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111・14・001 1/12 TSZ02201-0RCR0GZ00120-1-2 08.Jun.2016 Rev.004 BD95820F-LB BD95820N-LB Pin Configurations Block Diagrams SOP8 (TOP VIEW) 7 6 VS 5 6 7 8 OS NR SC 5 1 1 2 3 2 3 4 5 6 7 Latch block Reference voltage output block 8 SIP8 (TOP VIEW) 8 4 VR 1 IN 2 GND 3 OD 4 Pin Descriptions Pin No. Symbol Function 1 VR Reference voltage 2 IN Input 3 GND 4 OD Output of input comparator 5 SC Input of latch circuit 6 NR Noise absorption 7 OS Output 8 VS Power supply Ground Absolute Maximum Ratings (TA=25℃) Parameter Symbol Rating Unit IS 8 mA IN-VR current IIN-VR ±250 mA VR pin current IVR 30 mA IN terminal current IIN 30 mA SC terminal current ISC 5 mA Power Supply voltage VS 36 V Input terminal voltage VVR/IN 17 V VOD/SC/NR/OS 8 V Supply current (Note 3) OD/SC/NR/OS terminal voltage 0.68(SOP8) Power dissipation Storage temperature PD Tstg 1.12(SIP8) (Note 4) (Note 5) -55 to ＋150 W °C (Note 3) The power-supply voltage is limited by the internal clamping circuit. (Note 4) Mounted on 70mm x 70mm x 1.6mm glass epoxy board. Reduce 5.5mW per 1°C above 25°C. (Note 5) PD is a value in the package unit. Reduce 9.0mW per 1°C above 25°C. Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated over the absolute maximum ratings. www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 2/12 TSZ02201-0RCR0GZ00120-1-2 08.Jun.2016 Rev.004 BD95820F-LB BD95820N-LB Recommended Operating Ratings Parameter Symbol Limits Unit Supply voltage VS 12 to 22 V Operating temperature Topr -20 to＋95 °C Electrical Characteristics (Unless otherwise specified, VS=12V, GND=0V, TA =25℃, Full range: -20°C to +95°C) Limits Temperature Parameter Symbol range Min Typ Max -20°C - - 520 25°C - 330 500 95°C - - 460 VT Full range 6.1 7.5 OD Source current IODSO 25°C -27.2 OD Sink current IODSI 25°C IS1 Supply current Trip voltage OS Source current IOSSO Unit Conditions μA ΔVIN=VVR-VIN=30mV 8.9 mV VT=ΔVIN=VVR-VIN -20.6 -14.0 μA 16.7 26.0 35.3 μA -20°C -200 - - 25°C -100 - - 95°C -75 - - ΔVIN=VVR-VIN=30mV, VOD=1.2V VOD=0.8V, ΔVIN=VVR-VIN=0mV μA VSC=2.0V, VOS=0.8V VSC=0.2V, VOS=0.2V OS Sink current IOSSI Full range 200 - - μA SC ON voltage VSCON 25°C 1.00 1.24 1.48 V Input clamp voltage VIC Full range 4.2 5.5 6.7 V IIC=20mA Differential input clamp voltage VIDC Full range 0.6 1.0 1.4 V IIDC=100mA Maximum current voltage VSM 25°C 26 29 32 V IS=7mA IOS2 Full range -100 - - μA IS=900μA,VSC=2.0V VOS=0.8V VSOFF 25°C 2.7 3.7 4.7 V tON 25°C 1.8 2.9 4.0 ms Supply current 2 (Note 6) Latch OFF Supply Voltage Operating time (Note 7) (Note 6) Supply current 2 is OS source current value when the power supply current(Is=900μA) is given. (Note 7) Operating time is time until output voltage reaches 0.8V after detecting the leakage signal. Conditions : Capacitor(0.047μF) is connected between OD(OS) and GND. www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 3/12 TSZ02201-0RCR0GZ00120-1-2 08.Jun.2016 Rev.004 BD95820F-LB BD95820N-LB Test circuits 1.IS1 2.VT 3.IODSO VR IN GND OD SC NR OS VS VR IN GND OD SC NR OS VS VR IN GND OD SC NR OS VS 1 2 5 6 7 8 1 2 4 5 6 7 8 1 2 4 5 6 7 8 A IOD + A 3 IS VS V VOD VS 4.IODSI VS + ΔVIN ΔVIN 3 100Ω 100Ω 4 100Ω 3 ΔVIN 5.IOSSO/IOSSI VOD 6.VSCON VR IN GND OD SC NR OS VS VR IN GND OD SC NR OS VS VR IN GND OD SC NR OS VS 1 2 5 6 7 8 1 2 4 5 6 7 8 1 2 4 5 6 7 8 + A 3 IOD VSC VS + VOD A 3 100Ω 100Ω 4 100Ω 3 VS VSC IOS V Vos VOS 7.VIC 8.VIDC 9.VSM VR IN GND OD SC NR OS VS VR IN GND OD SC NR OS VS VR IN GND OD SC NR OS VS 1 2 5 6 7 8 1 2 4 5 6 7 8 1 2 4 5 6 7 8 3 VS IIDC V IC V VIC 3 100Ω 4 100Ω 3 VSM V IS VIDC 10.IOS2 11.VSOFF 12.tON SC NR OS VS VR IN GND OD SC NR OS VS VR IN GND OD SC NR OS VS 2 4 5 6 7 8 1 2 4 5 6 7 8 1 2 4 5 6 7 8 3 VSC IS + A IOS 100Ω IN GND OD 1 100Ω VR 3 0.047 μF VS V VOS ΔVIN VOS www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 4/12 3 0.047 μF V VS 0.047 μF TSZ02201-0RCR0GZ00120-1-2 08.Jun.2016 Rev.004 BD95820F-LB BD95820N-LB Timing Chart Input voltage between IN and VR ΔVIN(IN-VR) VT VSCON OD/SC terminal voltage VOD/VSC OS terminal voltage VOS 0.8V tON Application Hint 1. Input Resistance RIN Larger bias current flow through the input terminal "IN” in power-up state. This larger current generates undesirable voltage between the input terminals via input resistance. The input resistance should be less than 5kΩ so that this terminal voltage is restrained under the trip voltage and the voltage never cause any malfunction. Even in normal operation, the offset voltage caused via input resistance and bias current might produce undesirable trip voltage shift. The input resistance should be designed with sufficient margin against this shift. www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 5/12 TSZ02201-0RCR0GZ00120-1-2 08.Jun.2016 Rev.004 BD95820F-LB BD95820N-LB Typical Performance Curves(reference data) 800 1.2 1.1 SIP8 600 Supply Current IS[uA] 0.9 Power Dissipation [W] 105℃ 700 1.0 0.8 0.7 0.6 0.5 0.4 SOP8 0.3 500 -60℃ 25℃ 400 300 200 0.2 100 0.1 0.0 0 95 0 50 25 100 75 125 150 0 5 Ambient Temperature Ta [℃] Figure 1 Derating curve 30 Figure 2 Circuit current - Supply voltage 40 0 OS terminal Source Current IOSSO[uA] 30 Rate of fluctuation Δ[%] 25 10 15 20 Power Supply VS [V] 20 RIN=300 10 0 -10 RIN=1kΩ -20 -30 -40 -100 105℃ -200 25℃ -300 -60℃ -400 -500 -60 -40 -20 0 20 40 60 80 100 120 Ambient Temperature Ta [℃] 5 10 15 20 25 Power Supply VS [V] Figure 3 Trip voltage fluctuation rate - Ambient temperature www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 0 Figure 4 OS terminal source current - Supply voltage 6/12 TSZ02201-0RCR0GZ00120-1-2 08.Jun.2016 Rev.004 BD95820F-LB BD95820N-LB 5 10 4 8 OS terminal voltage VOS[V] Operating time tON[ms] Typical Performance Curves(reference data) - continued 3 2 6 4 -60℃ 2 1 25℃ 105℃ 0 0 -60 -40 -20 0 40 20 60 80 100 0 120 1 Ambient Temperature Ta [℃] 10 10 8 8 6 105℃ 25℃ 8 10 9 Figure 6 Latch OFF supply voltage - Ambient temperature OS Terminal Voltage VOS [V] OS terminal voltage VOS[V] Figure 5 Operating time - Ambient temperature 7 5 6 3 4 Power Supply VS [V] 2 -60℃ 4 2 6 4 -60℃ 25℃ 2 105℃ 0 0 0.6 0.8 1.0 1.2 1.4 1.6 0 1.8 2 3 4 5 6 7 8 9 10 Power Supply VS [V] SC terminal input voltage VSCON [V] Figure 7 SC ON voltage - Ambient temperature www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 1 Figure 8 Latch ON supply voltage - Ambient temperature 7/12 TSZ02201-0RCR0GZ00120-1-2 08.Jun.2016 Rev.004 BD95820F-LB BD95820N-LB Power Dissipation Power dissipation(total loss) indicates the power that can be consumed by IC at TA=25°C (normal temperature).IC is heated when it consumed power, and the temperature of IC chip becomes higher than ambient temperature. The temperature that can be accepted by IC chip depends on circuit configuration, manufacturing process, and consumable power is limited. Power dissipation is determined by the temperature allowed in IC chip (maximum junction temperature) and thermal resistance of package (heat dissipation capability). The maximum junction temperature is typically equal to the maximum value in the storage temperature range. Heat generated by consumed power of IC radiates from the mold resin or lead frame of the package. The parameter which indicates this heat dissipation capability(hardness of heat release)is called thermal resistance, represented by the symbol θJA°C/W. The temperature of IC inside the package can be estimated by this thermal resistance. Figure 9(a) shows the model of thermal resistance of the package. Thermal resistance θJA, ambient temperature TA, junction temperature TJmax, and power dissipation PD can be calculated by the equation below. °C /W θJA = (TJmax - TA) / PD Derating curve in Figure 9(b) indicates power that can be consumed by IC with reference to ambient temperature. Power that can be consumed by IC begins to attenuate at certain ambient temperature. This gradient is determined by thermal resistance θJA. Thermal resistance θJA depends on chip size, power consumption, package, ambient temperature, package condition, wind velocity, etc even when the same of package is used. Thermal reduction curve indicates a reference value measured at a specified condition. Figure 10(a) show a derating curve for an example of BD95820F-LB, BD95820N-LB . PowerLSI dissipation LSI[W] の消費電力 LSIの 消 費 of 電力 PPd D(max) (max) θJA =(TJmax-TA)/P °C /W θ JA2 < JA1 θja2 < θθja1 P2 Ambient temperature TA[°C] 周囲温度 Ta [℃] θ’ θ' JA2 ja2 P1 θ’θ'JA1 ja1 0 表面温度 Tj Chip surfaceチップ temperature TJ[℃] [°C] 25 消費電力 P [W] θθJA2 ja2 T’Jmax TTjJmax Tj ' (max) (max) θθJA1 ja1 50 75 100 125 TA [℃ 周囲温度 [ T°C ] ] 周temperature 囲 温 度 Ta Ambient A [°C] 150 (a) Thermal Resistance (b) Derating Curve Figure 9. Thermal resistance and derating 1.2 1.1 1.0 Power Dissipation [W] 0.9 BD95820N-LB(SIP8) 0.8 0.7 0.6 0.5 0.4 BD95820F-LB(SOP8) 0.3 0.2 0.1 0.0 95 0 25 50 75 100 125 150 [℃] Ambient Temperature TaTA[℃] (a) BD95820F-LB・BD95820N-LB Derating curve slope BD95820F-LB(SOP8) 5.5 BD95820N-LB(SIP8) 9.0 UNIT mW/℃ When using the unit above TA=25℃, subtract the value above per degree℃ BD95820F-LB : Permissible dissipation is a value when glass epoxy board 70mm×70mm×1.6mm (cooper foil area below 3%) is mounted. BD95820N-LB : Permissible dissipation is a value in the package unit. Figure 10. Derating curve www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 8/12 TSZ02201-0RCR0GZ00120-1-2 08.Jun.2016 Rev.004 BD95820F-LB BD95820N-LB I/O equivalence circuit VCC VCC VS 300Ω Pin 1 [VR] Pin 5 [SC] 100kΩ ESD PRO TECT Pin 2 VCC VCC VS Pin 1 Pin 2 [IN] VCC 300Ω Pin 6 [NR] 100kΩ Pin 7 VCC Pin 6 Pin 3 [GND] VCC Pin 7 [OS] VCC VCC VCC line (Internal Power Supply Line) Pin 4 [OD] www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 Pin 8 [VS] 9/12 TSZ02201-0RCR0GZ00120-1-2 08.Jun.2016 Rev.004 BD95820F-LB BD95820N-LB Operational Notes 1. Reverse Connection of Power Supply Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when connecting the power supply, such as mounting an external diode between the power supply and the IC’s power supply pins. 2. Power Supply Lines Design the PCB layout pattern to provide low impedance supply lines. Separate the ground and supply lines of the digital and analog blocks to prevent noise in the ground and supply lines of the digital block from affecting the analog block. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and aging on the capacitance value when using electrolytic capacitors. 3. Ground Voltage Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition. 4. Ground Wiring Pattern When using both small-signal and large-current ground traces, the two ground traces should be routed separately but connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal ground caused by large currents. Also ensure that the ground traces of external components do not cause variations on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance. 5. Thermal Consideration Should by any chance the power dissipation rating be exceeded the rise in temperature of the chip may result in deterioration of the properties of the chip. The absolute maximum rating of the Pd stated in this specification is when the IC is mounted on a 70mm x 70mm x 1.6mm glass epoxy board. In case of exceeding this absolute maximum rating, increase the board size and copper area to prevent exceeding the Pd rating. 6. Recommended Operating Conditions These conditions represent a range within which the expected characteristics of the IC can be approximately obtained. The electrical characteristics are guaranteed under the conditions of each parameter. 7. Inrush Current When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush current may flow instantaneously due to the internal powering sequence and delays, especially if the IC has more than one power supply. Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and routing of connections. 8. Operation Under Strong Electromagnetic Field Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction. 9. Testing on Application Boards When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may subject the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply should always be turned off completely before connecting or removing it from the test setup during the inspection process. To prevent damage from static discharge, ground the IC during assembly and use similar precautions during transport and storage. 10. Inter-pin Short and Mounting Errors Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin. Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and unintentional solder bridge deposited in between pins during assembly to name a few. 11. Unused Input Pins Input pins of an IC are often connected to the gate of a MOS transistor. The gate has extremely high impedance and extremely low capacitance. If left unconnected, the electric field from the outside can easily charge it. The small charge acquired in this way is enough to produce a significant effect on the conduction through the transistor and cause unexpected operation of the IC. So unless otherwise specified, unused input pins should be connected to the power supply or ground line. www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 10/12 TSZ02201-0RCR0GZ00120-1-2 08.Jun.2016 Rev.004 BD95820F-LB BD95820N-LB Operational Notes – continued 12. Regarding the Input Pin of the IC This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them isolated. P-N junctions are formed at the intersection of the P layers with the N layers of other elements, creating a parasitic diode or transistor. For example (refer to figure below): When GND > Pin A and GND > Pin B, the P-N junction operates as a parasitic diode. When GND > Pin B, the P-N junction operates as a parasitic transistor. Parasitic diodes inevitably occur in the structure of the IC. The operation of parasitic diodes can result in mutual interference among circuits, operational faults, or physical damage. Therefore, conditions that cause these diodes to operate, such as applying a voltage lower than the GND voltage to an input pin (and thus to the P substrate) should be avoided. Figure 11. Example of monolithic IC structure Ordering Information B D 9 5 8 Part Number 2 0 F Package F: SOP8 N:SIP8 - LBE2 Product class LB for Industrial applications Packaging and forming specification E2: Embossed tape and reel (SOP8) None:Container tube (SIP8) Marking Diagrams SIP8 (TOP VIEW) SOP8 (TOP VIEW) 9 5 8 2 B D 9 5 8 2 0 0 LOT Number LOT Number １PIN MARK 1PIN MARK www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 11/12 TSZ02201-0RCR0GZ00120-1-2 08.Jun.2016 Rev.004 BD95820F-LB BD95820N-LB Physical Dimension Tape and Reel Information Revision History Date Revision 13.Jun.2014 001 29.Sep.2014 002 28.Sep.2015 003 Changes New Release RIN≦3kΩ-> RIN≦5kΩ Page.1 Typical Application Circuit Page.10 Operational Notes 13.Input Resistance RIN Page.1 Key Specifications: Trip Voltage 4.92mV to 11.06mV -> 6.9mV to 8.9mV Typical Application Circuit: Add the Recommended External Parts Value Page.2 Absolute Maximum Ratings: Add the sentence of Caution Page.3 Electrical Characteristics: Trip Voltage 4.92mV to 11.06mV -> 6.9mV to 8.9mV Page.5 Application Hint: Add 1. Input Resistance RIN (Moved from Operational Notes 13) 08.Jun.2016 Page.1 Key Specifications: Trip Voltage 6.9mV to 8.9mV -> 6.1mV to 8.9mV Page.3 Electrical Characteristics: Trip Voltage 4.92mV to 11.06mV -> 6.1mV to 8.9mV Page.12 Revision History (Add to Revision History Rev.003) Page.3 Recommended Operating Ratings Deleted symbols CVS ,COS and moved to Page.1 Typical Application Circuit 004 www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 12/12 TSZ02201-0RCR0GZ00120-1-2 08.Jun.2016 Rev.004 Notice Precaution on using ROHM Products 1. (Note 1) If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment , aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅢ CLASSⅣ CLASSⅢ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in the range that does not exceed the maximum junction temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice-PAA-E © 2015 ROHM Co., Ltd. All rights reserved. Rev.003 Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign trade act, please consult with ROHM in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the Products with other articles such as components, circuits, systems or external equipment (including software). 3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the Products, subject to the terms and conditions herein. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice-PAA-E © 2015 ROHM Co., Ltd. All rights reserved. Rev.003 Datasheet General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s representative. 3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. Notice – WE © 2015 ROHM Co., Ltd. All rights reserved. Rev.001 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: ROHM Semiconductor: BD95820F-LBE2 BD95820N-LB