BD9D320EFJ-E2

Datasheet 4.5V to 18V Input, 3.0A Integrated MOSFET 1ch Synchronous Buck DC/DC Converter BD9D320EFJ General Description BD9D320EFJ is a synchronous buck switching regulator with built-in low on-resistance power MOSFETs. It is capable of providing current of up to 3 A. External phase compensation circuit is not necessary for it is a constant on-time control DC/DC converter with high speed response. Features         Synchronous Single DC/DC Converter Constant On-time Control Over Current Protection Short Circuit Protection Thermal Shutdown Protection Under Voltage Lockout Protection Adjustable Soft Start HTSOP-J8 Package (Backside Heat Dissipation) Key Specifications  Input Voltage Range: 4.5V to 18.0 V  Output Voltage Setting Range: 0.765V to 7V (VIN×0.07)V to (VIN×0.65)V  Reference Voltage: 0.765V ± 1.5%  Output Current: 3 A (Max)  Switching Frequency: 700 kHz (Typ)  High Side MOSFET On-Resistance:100 m Ω (Typ)  Low Side MOSFET On-Resistance: 70 m Ω (Typ)  Standby Current: 2 μA (Typ) Package HTSOP-J8 W (Typ) x D (Typ) x H (Max) 4.90mm x 6.00mm x 1.00mm Applications  Step-down Power Supply for DSPs, FPGAs, Microprocessors, etc.  Set-top Box  LCD TVs  DVD / Blu-ray Player / Recorder  Entertainment Devices HTSOP-J8 Typical Application Circuit Figure 1. Typical Application Circuit ○Product structure: Silicon monolithic integrated circuit ○This product has no designed protection against radioactive rays. www.rohm.co.jp TSZ02201-0J3J0AC00480-1-2 © 2013 ROHM Co., Ltd. All rights reserved. 1/23 TSZ22111・14・001 07.Aug.2013 Rev.001 Datasheet BD9D320EFJ Pin Configuration (TOP VIEW) EN 1 8 VIN FB 2 7 BOOT VREG 3 6 SW SS 4 5 GND Figure 2. Pin Assignment Pin Descriptions Terminal No. Symbol Function 1 EN Turning this terminal signal low level (0.3 V or lower) forces the device to enter the shutdown mode. Turning this terminal signal high level (2.2 V or higher) enables the device. This terminal must be terminated. 2 FB An inverting input terminal of comparator which compares with reference voltage (VREF). Refer to page.15 for how to calculate the resistance of the output voltage setting. 3 VREG 4 SS 5 GND Power supply voltage terminal inside IC. Voltage of 5.25V (Typ) is outputted with more than 2.2V is impressed to EN terminal. Connect 1µF ceramic capacitor to ground. Terminal for setting the soft start time. The rise time of the output voltage can be specified by connecting a capacitor to this terminal. Refer to page.15 for how to calculate the capacitance. Ground terminal for the output stage of the switching regulator and the control circuit Switch node. This terminal is connected to the source of the high-side MOSFET and drain of the low-side MOSFET. Connect a bootstrap capacitor of 0.1µF between this terminal and BOOT terminal. In addition, connect an inductor considering the direct current superimposition characteristic. 6 SW 7 BOOT 8 VIN Power supply terminal for the switching regulator. Connecting a 20µF(10µF×2) and 0.1µF ceramic capacitor to ground is recommended. - FIN A backside heat dissipation pad. Connecting to the internal PCB ground plane by using multiple via provides excellent heat dissipation characteristics. Connect a bootstrap capacitor of 0.1µF between this terminal and SW terminal. The voltage of this capacitor is the gate drive voltage of the high-side MOSFET. www.rohm.co.jp © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111•15•001 2/23 TSZ02201-0J3J0AC00480-1-2 07.Aug.2013 Rev.001 Datasheet BD9D320EFJ Block Diagram 3 VREG VIN VREG VIN Thermal Protection VOUT TSD 8 5V REG VREG 7 BG EN UVLO TSD SS BOOT BG EN On Time Controller Block Soft Start 4 R S Q SW OCP FB 2 VIN VOUT Driver Circuit 6 SW 5 REF SS GND UVLO OCP TSD EN 1 EN Logic UVLO Figure 3. Block Diagram www.rohm.co.jp © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111•15•001 3/23 TSZ02201-0J3J0AC00480-1-2 07.Aug.2013 Rev.001 Datasheet BD9D320EFJ Absolute Maximum Ratings (Ta = 25C) Parameter Symbol Rating Unit Input Voltage (Note 1) VIN 20 V BOOT Voltage (Note 1) VBOOT 27 V BOOT-SW Voltage (Note 1) VBOOT-VSW 7 V Output Feedback Voltage VFB VREG V SW Voltage (Note 1) VSW 20 V VREG 7 V SS Voltage (Note 1) VSS 7 V Logic Input Voltage (Note 1) VEN 20 V Pd 3.75 W Operating Temperature Range Topr -40 to +85 °C Storage Temperature Range Tstg -55 to +150 °C Tjmax +150 °C VREG Voltage (Note 1) Power dissipation (Note 2) Junction Temperature (Note 1) No need to exceed Pd. (Note 2) Derating in done 30.08 mW/°C for operating above Ta ≥ 25°C (Mount on 4-layer 70.0mm×70.0mm×1.6mm board) Caution1: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated over the absolute maximum ratings. Caution2: The operating temperature range is intended to guarantee functional operation and does not guarantee the life of the LSI within this range. The life of the LSI is subject to derating depending on usage environment such as the voltage applied, ambient temperature and humidity. Consider derating in the design of equipment and devices. Recommended Operating Conditions Limit Parameter Symbol Unit Min Typ Max Input voltage VIN 4.5 12 18 V BOOT voltage VBOOT 4.5 - 24 V VSW -0.7 - +18 V BOOT-SW voltage VBOOT-VSW 4.5 - 5.5 V Logic Input Voltage VEN 0 - 18 V Output Current IOUT - - 3 A VRANGE 0.765 (Note 3) - 7 (Note 4) V SW Voltage Output Voltage Range (Note 3) Please use under the condition of VOUT ≥ VIN×0.07 [V]. (Note 4) Please use under the condition of VOUT ≤ VIN×0.65 [V]. (Refer to the page 15 for how to calculate the output voltage setting.) www.rohm.co.jp © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111•15•001 4/23 TSZ02201-0J3J0AC00480-1-2 07.Aug.2013 Rev.001 Datasheet BD9D320EFJ Electrical Characteristics (Ta = 25°C, VIN = 12V, VEN = 3V unless otherwise specified) Limit Parameter Symbol Unit Min Typ Max Conditions Standby Circuit Current ISTB - 2 15 µA VEN=GND Operating Circuit Current IVIN - 1 2 mA VEN=3V, IOUT=0mA when no switching EN Low Voltage VENL - - 0.3 V EN High Voltage VENH 2.2 - VIN V EN Bias Current IEN - 3 10 µA VEN=3V VVREG_STB - - 0.1 V VEN=GND VVREG 5 5.25 5.5 V IREG - 10 - mA UVLO Threshold Voltage VVREG_UVLO 3.4 3.8 4.2 V UVLO Hysteresis Voltage dVVREG_UVLO 200 300 400 mV VREF 0.753 0.765 0.777 V FB Input Current IFB - - 1 µA SS Charge Current ISSC 1.4 2.0 2.6 µA SS Discharge Current ISSD 0.1 0.2 - mA Ton - 215 - nsec Toffmin 100 200 - nsec High Side FET ON Resistance RONH - 100 200 mΩ Low Side FET ON Resistance RONL - 70 140 mΩ Iocp - 5 - A VREG Standby Voltage VREG Output Voltage Maximum Current < Under-Voltage Lock-Out Block > VREG: Sweep up VREG: Sweep down < Reference Voltage Block > FB Threshold Voltage VIN=12V, VOUT=1.8V VREG=5.25V, VSS=0.5V < On Time Control Block > On Time Minimum Off Time VIN=12V, VOUT=1.8V < Over Current Protection Block > Over Current Protection Current Limit (Note 5) (Note 5) No tested on outgoing inspection. www.rohm.co.jp © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111•15•001 5/23 TSZ02201-0J3J0AC00480-1-2 07.Aug.2013 Rev.001 Datasheet BD9D320EFJ Typical Performance Curves 10 1200 9 1000 8 VIN Supply Current [µA] VIN Supply Current [µA] VIN=12V 800 600 400 7 6 5 4 3 VIN=12V 2 200 1 0 -50 0 Tj [°C] 50 0 -50 100 0 50 100 Tj [°C] Figure 4. VIN Current vs Junction Temperature Figure 5. VIN Shutdown Current vs Junction Temperature 1.86 100 90 1.84 70 1.82 60 VOUT [V] EN Input Current [µA] 80 50 40 VIN=12V 1.80 1.78 30 20 1.76 10 0 1.74 0 5 10 15 20 0 0.5 1 1.5 2 2.5 EN [V] IOUT [A] Figure 6. EN Current vs EN Voltage Figure 7. Output Voltage vs Output Current www.rohm.co.jp © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111•15•001 6/23 3 TSZ02201-0J3J0AC00480-1-2 07.Aug.2013 Rev.001 Datasheet BD9D320EFJ Typical Performance Curves (Continued) 1.86 VOUT 50mV/div 1.84 VOUT [V] 1.82 IOUT=0A 1.80 IOUT 2.0A/div 1.78 1.76 1.74 0 5 10 15 100µsec/div 20 VIN[V] Figure 9. Load Transient Response (VIN=12V, VOUT=1.8V, IOUT=50mA to 3A) Figure 8. Output Voltage vs Input Voltage EN 5V/div VIN 10V/div VREG 5V/div VREG 5V/div SW 10V/div SW 10V/div VOUT 1V/div VOUT 1V/div 500µsec/div 500µsec/div Figure 11. Start-up Waveform（VIN=EN） (VIN=12V, VOUT=1.8V, IOUT=3A, Css=3300pF) Figure 10. Start-up Waveform（EN=0V→5V） (VIN=12V, VOUT=1.8V, IOUT=3A, Css=3300pF) www.rohm.co.jp © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111•15•001 7/23 TSZ02201-0J3J0AC00480-1-2 07.Aug.2013 Rev.001 Datasheet BD9D320EFJ Typical Performance Curves (Continued) VIN 10V/div EN 5V/div VREG 5V/div VREG 5V/div SW 10V/div SW 10V/div VOUT 1V/div VOUT 1V/div 500µsec/div 500µsec/div Figure 12. Shutdown Waveform（EN=5V→0V） (VIN=12V, VOUT=1.8V, IOUT=3A, Css=3300pF) Figure 13. Shutdown Waveform（VIN=EN） (VIN=12V, VOUT=1.8V, IOUT=3A, Css=3300pF) 100 90 80 EFFICIENCY [%] 70 VOUT =7.0V 60 VOUT =5.0V 50 VOUT =3.3V 40 VOUT =1.8V 30 VOUT =1.05V 20 VIN=12V 10 0 0 0.5 1 1.5 2 2.5 3 IOUT[A] Figure 14. Efficiency vs Output Current www.rohm.co.jp © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111•15•001 8/23 TSZ02201-0J3J0AC00480-1-2 07.Aug.2013 Rev.001 Datasheet BD9D320EFJ 900 900 850 850 800 800 750 Switching Frequency [kHz] Switching Frequency [kHz] Typical Performance Curves (Continued) VOUT=1.8V 700 650 600 550 VOUT=1.8V 750 700 650 600 550 500 500 450 450 VIN=12V IOUT=1A 400 400 0 5 10 15 0 20 0.5 1 1.5 2 2.5 3 IOUT [A] VIN[V] Figure 15. Switching Frequency vs Input Voltage Figure 16. Switching Frequency vs Output Current VOUT 20mV/div VIN 100mV/div SW 5V/div SW 5V/div 500nsec/div 500nsec/div Figure 17. Voltage Ripple at Output Figure 18. Voltage Ripple at Input (VIN=12V, VOUT=1.8V, IOUT=2A, L=2.2µH, COUT=22µF x 2) (VIN=12V, VOUT=1.8V, IOUT=2A, L=2.2µH, CIN=10µF x 2) www.rohm.co.jp © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111•15•001 9/23 TSZ02201-0J3J0AC00480-1-2 07.Aug.2013 Rev.001 Datasheet BD9D320EFJ Function Explanations 1 Basic Operation 1-1 Constant On Time Control BD9D320EFJ is a single synchronous buck switching regulator employing a constant on-time control system. It controls the on-time by using the duty ratio of VOUT /VIN inside IC so that a switching frequency becomes 700 kHz. Therefore it runs with the frequency of 700 kHz under the constant on-time decided with VOUT / VIN. 1-2 Enable Control The IC shutdown can be controlled by the voltage applied to the EN terminal. When VEN reaches 2.2 V (Typ), the internal circuit is activated and the IC starts up. VEN EN terminal VENH VENL 0 t VOUT Output setting voltage 0 t Soft start time Figure19. Start-up with EN pin 1-3 Soft Start Function By turning EN terminal to High, the soft start function operates and it gradually starts output voltage by controlling the current at start-up. Also soft start function prevents sudden current and over shoot of output voltage. Rising time can be set by connecting capacitor to SS terminal. For setting the rising time, please refer to page.15. EN SS VTH VOUT 0.765V FB Td Tss Figure 20. Soft Start Timing chart www.rohm.co.jp © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111•15•001 10/23 TSZ02201-0J3J0AC00480-1-2 07.Aug.2013 Rev.001 Datasheet BD9D320EFJ 2 Protective Functions The protective circuits are intended for prevention of damage caused by unexpected accidents. Do not use them for continuous protective operation. 2-1 Over Current Protection (OCP) Over current protection function is effective by controlling current which flows in low side MOSFET by 1 cycle each of switching period. With inductor current exceeding the current restriction setting value IOCP when LG is ON, the HG pulse cannot be hit even with FB voltage under REF voltage and LG continues to be ON until it is below IOCP. It hits HG when it goes below IOCP. As a result both frequency and duty fluctuates and output voltage may decrease. In a case where output is decreased because of OCP, output may rise after OCP is released due to the action at high speed load response. This is non-latch protection and after over current situation is released the output voltage will recover. VOUT FB High side MOSFET gate (HG) Low side MOSFET gate (LG) OCP threshold (Iocp) Inductor current OCP signal inside IC Output load current Normal Over Current Normal Figure 21. Over current protection timing chart www.rohm.co.jp © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111•15•001 11/23 TSZ02201-0J3J0AC00480-1-2 07.Aug.2013 Rev.001 Datasheet BD9D320EFJ 2-2 Under Voltage Lockout Protection (UVLO) The Under Voltage Lockout Protection circuit monitors the VREG terminal voltage. The operation enters standby when the VREG terminal voltage is 3.5 V (Typ) or lower. The operation starts when the VREG terminal voltage is 3.8 V (Typ) or higher. Figure 22. UVLO Timing Chart ※Load at Startup Ensure that the respective output has light load at startup of this IC. Also, restrain the power supply line noise at startup and voltage drop generated by operating current within the hysteresis width of UVLO. Noise exceeding the hysteresis noise width may cause the IC to malfunction. 2-3 Thermal Shutdown Function When the chip temperature exceeds Tj = 175°C, the DC/DC converter is stopped. The thermal shutdown circuit is intended for shutting down the IC from thermal runaway in an abnormal state with the temperature exceeding Tjmax = 150°C. Do not use this function for application protection design. This is non-latch protection. www.rohm.co.jp © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111•15•001 12/23 TSZ02201-0J3J0AC00480-1-2 07.Aug.2013 Rev.001 Datasheet BD9D320EFJ Application Example Figure 23. Application Circuit VOUT [V] Table 1. Recommended Component values R1 [kΩ] R2 [kΩ] C1 [pF] L [µH] (Note 7) 1.0 6.8 22 - (Note 6) 1.5 1.05 8.2 22 - (Note 6) 1.5 (Note 6) 1.5 1.2 12+0.51 22 - 1.8 30 22 - (Note 6) 2.2 (Note 6) 2.2 3.3 68+5.1 22 - 5.0 120+1.8 22 - (Note 6) 3.3 7.0 180 22 - (Note 6) 3.3 (Note 6) C1 is a feed forward capacitor. The IC can operate normally even if the capacitor is not connected. Additional phase boost can be achieved by adding the 5pF to 100pF capacitor (C1) in parallel with R1. (Note 7) Recommended Inductor ・ALPS GLMC series ・TDK SPM6530 series Selection of Components Externally Connected (1) Output LC Filter Constant The DC/DC converter requires an LC filter for smoothing the output voltage in order to supply a continuous current to the load. Selecting an inductor with a large inductance causes the ripple current ∆IL that flows into the inductor to be small. However, decreasing the ripple voltage generated in the output is not advantageous in terms of the load transient response characteristic. An inductor with a small inductance improves the transient response characteristic but causes the inductor ripple current to be large which increases the ripple voltage in the output voltage, showing a trade-off relationship. The recommended inductor values are shown in Table 1. www.rohm.co.jp © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111•15•001 13/23 TSZ02201-0J3J0AC00480-1-2 07.Aug.2013 Rev.001 Datasheet BD9D320EFJ IL Inductor saturation current > IOUTMAX +⊿IL /2 ⊿IL Average inductor current (Output Current：IOUT) t Figure 24. Waveform of current through inductor Figure 25. Output LC filter circuit The inductor peak to peak ripple current ⊿IL is calculated using the following equation. ΔIL = VOUT × (VIN－VOUT ) × 1 VIN × FOSC × L [A] For example, with VIN = 12 V, VOUT = 1.8 V, L = 2.2µH and the switching frequency FOSC = 700 kHz, the calculated peak current ⊿IL is 1.0A. Then, the inductor saturation current must be larger than the sum of the maximum output current (IOUTMAX) and 1/2 of the inductor ripple current (∆IL / 2). The output capacitor COUT affects the output ripple voltage characteristics. The output capacitor COUT must satisfy the required ripple voltage characteristics. The output ripple voltage can be represented by the following equation. ΔVRPL = ΔI L × (R ESR + 1 8 × COUT × FOSC ) [V] RESR is the Equivalent Series Resistance (ESR) of the output capacitor. ※The capacitor rating must allow a sufficient margin with respect to the output voltage. The output ripple voltage can be decreased with a smaller ESR. A ceramic capacitor of about 22 µF to 100 µF is recommended. ※Pay attention to total capacitance value, when additional capacitor CLOAD is connected in addition to output capacitor COUT. Then, please determine CLOAD and soft start time Tss (Refer to (3) Soft Start Setting) as satisfying the following equation. COUT + CLOAD ≤ (IOCP－IOUT ) × TSS VOUT [μF] IOCP is Over Current Protection Current limit value. www.rohm.co.jp © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111•15•001 14/23 TSZ02201-0J3J0AC00480-1-2 07.Aug.2013 Rev.001 Datasheet BD9D320EFJ (2) Output Voltage Setting The output voltage value can be set by the feedback resistance ratio. VOUT VOUT = R1 FB R2 Voltage Reference R1 + R2 × 0.765 R2 [V] BD9D320EFJ can operate under the condition which satisfies the following equation. 0.07 ≤ VOUT ≤ 0.65 VIN Figure 26. Feedback Resistor Circuit (3) Soft Start Setting Turning the EN terminal signal High activates the soft start function. This causes the output voltage to rise gradually while the current at startup is placed under control. This allows the prevention of output voltage overshoot and inrush current. The rise time depends on the value of the capacitor connected to the SS terminal. Td = (CSS × VTH ) I SS TSS  (C SS  VFB  1.15) I SS Td : Soft Start Delay Time Tss : Soft Start Time Css : Capacitor connected to Soft Start Time Terminal VFB : FB Terminal Voltage (0.765V Typ) VTH : Internal MOS threshold voltage (0.7V Typ) Iss : Soft Start Terminal Source Current (2.0µA Typ) With Css = 3300pF, Td = ( 3300 pF x 0.7 V ) / 2.0 µA = 1.16msec Tss= ( 3300 pF x 0.765 V x 1.15 ) / 2.0 µA = 1.45 msec www.rohm.co.jp © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111•15•001 15/23 TSZ02201-0J3J0AC00480-1-2 07.Aug.2013 Rev.001 Datasheet BD9D320EFJ PCB Layout Design In the step-down DC/DC converter, a large pulse current flows into two loops. The first loop is the one into which the current flows when the high side FET is turned ON. The flow starts from the input capacitor CIN, runs through the FET, inductor L and output capacitor COUT and back to ground of CIN via ground of COUT. The second loop is the one into which the current flows when the low side FET is turned on. The flow starts from the low side FET, runs through the inductor L and output capacitor COUT and back to ground of the low side FET via ground of COUT. Route these two loops as thick and as short as possible to allow noise to be reduced for improved efficiency. It is recommended to connect the input and output capacitors directly to the ground plane. The PCB layout has a great influence on the DC/DC converter in terms of all of the heat generation, noise and efficiency characteristics. VIN MOS FET CIN VOUT L COUT Figure 27. Current Loop of Buck Converter Accordingly, design the PCB layout considering the following points.      Connect an input capacitor as close as possible to the IC VIN terminal on the same plane as the IC. If there is any unused area on the PCB, provide a copper foil plane for the ground node to assist heat dissipation from the IC and the surrounding components. Switching nodes such as SW are susceptible to noise due to AC coupling with other nodes. Route the coil pattern as thick and as short as possible. Provide lines connected to FB and SS far from the SW nodes. Place the output capacitor away from the input capacitor in order to avoid the effect of harmonic noise from the input. EN GND_S GND VIN EN VIN_S GND_S GND VIN VIN_S VOUT_S VOUT_S CIN CBOOT R1 R2 VOUT C1 VOUT CVREG CSS L COUT GND GND GND_S GND_S TOP Layer Bottom Layer Figure 28. Example of PCB layout www.rohm.co.jp © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111•15•001 16/23 TSZ02201-0J3J0AC00480-1-2 07.Aug.2013 Rev.001 Datasheet BD9D320EFJ Power Dissipation When designing the PCB layout and peripheral circuitry, sufficient consideration must be given to ensure that the power dissipation is within the allowable dissipation curve. HTSOP-J8 Package 70  70  1.6 mm assembled glass epoxide board (1) 4-layer board (Copper foil area 70 mm  70 mm) (2) 2-layer board (Copper foil area 70 mm  70 mm) (3) 2-layer board (Copper foil area 15 mm  15 mm) (4) 1-layer board (Copper foil area 0 mm 0 mm) Figure 29. Power dissipation (HTSOP-J8) www.rohm.co.jp © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111•15•001 17/23 TSZ02201-0J3J0AC00480-1-2 07.Aug.2013 Rev.001 Datasheet BD9D320EFJ I/O Equivalent Circuit 1. EN 2. FB EN 166kΩ 333kΩ 500kΩ 3. VREG 4. SS VIN VREG VREG SS 2.3kΩ 6. SW 7. BOOT BOOT VREG VIN VIN BOOT SW SW Figure 30. I/O equivalence circuit www.rohm.co.jp © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111•15•001 18/23 TSZ02201-0J3J0AC00480-1-2 07.Aug.2013 Rev.001 Datasheet BD9D320EFJ Operational Notes 1. Reverse Connection of Power Supply Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when connecting the power supply, such as mounting an external diode between the power supply and the IC’s power supply terminals. 2. Power Supply Lines Design the PCB layout pattern to provide low impedance supply lines. Separate the ground and supply lines of the digital and analog blocks to prevent noise in the ground and supply lines of the digital block from affecting the analog block. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and aging on the capacitance value when using electrolytic capacitors. 3. Ground Voltage Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition. 4. Ground Wiring Pattern When using both small-signal and large-current ground traces, the two ground traces should be routed separately but connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal ground caused by large currents. Also ensure that the ground traces of external components do not cause variations on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance. 5. Thermal Consideration Should by any chance the power dissipation rating be exceeded the rise in temperature of the chip may result in deterioration of the properties of the chip. The absolute maximum rating of the Pd stated in this specification is when the IC is mounted on 4 - layer 70mm x 70mm x 1.6mm glass epoxy board. In case of exceeding this absolute maximum rating, increase the board size and copper area to prevent exceeding the Pd rating. 6. Recommended Operating Conditions These conditions represent a range within which the expected characteristics of the IC can be approximately obtained. The electrical characteristics are guaranteed under the conditions of each parameter. 7. Rush Current When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush current may flow instantaneously due to the internal powering sequence and delays, especially if the IC has more than one power supply. Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and routing of connections. 8. Operation Under Strong Electromagnetic Field Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction. 9. Testing on Application Boards When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may subject the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply should always be turned off completely before connecting or removing it from the test setup during the inspection process. To prevent damage from static discharge, ground the IC during assembly and use similar precautions during transport and storage. 10. Inter-pin Short and Mounting Errors Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin. Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and unintentional solder bridge deposited in between pins during assembly to name a few. www.rohm.co.jp © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111•15•001 19/23 TSZ02201-0J3J0AC00480-1-2 07.Aug.2013 Rev.001 Datasheet BD9D320EFJ Operational Notes – continued 11. Regarding the Input Pin of the IC This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them isolated. P-N junctions are formed at the intersection of the P layers with the N layers of other elements, creating a parasitic diode or transistor. For example (refer to figure below): When GND > Pin A and GND > Pin B, the P-N junction operates as a parasitic diode. When GND > Pin B, the P-N junction operates as a parasitic transistor. Parasitic diodes inevitably occur in the structure of the IC. The operation of parasitic diodes can result in mutual interference among circuits, operational faults, or physical damage. Therefore, conditions that cause these diodes to operate, such as applying a voltage lower than the GND voltage to an input pin (and thus to the P substrate) should be avoided. Figure 31. Example of monolithic IC structure 12. Ceramic Capacitor When using a ceramic capacitor, determine the dielectric constant considering the change of capacitance with temperature and the decrease in nominal capacitance due to DC bias and others. 13. Thermal Shutdown Circuit(TSD) This IC has a built-in thermal shutdown circuit that prevents heat damage to the IC. Normal operation should always be within the IC’s power dissipation rating. If however the rating is exceeded for a continued period, the junction temperature (Tj) will rise which will activate the TSD circuit that will turn OFF all output pins. When the Tj falls below the TSD threshold, the circuits are automatically restored to normal operation. Note that the TSD circuit operates in a situation that exceeds the absolute maximum ratings and therefore, under no circumstances, should the TSD circuit be used in a set design or for any purpose other than protecting the IC from heat damage. 14. Over Current Protection Circuit (OCP) This IC incorporates an integrated overcurrent protection circuit that is activated when the load is shorted. This protection circuit is effective in preventing damage due to sudden and unexpected incidents. However, the IC should not be used in applications characterized by continuous operation or transitioning of the protection circuit. www.rohm.co.jp © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111•15•001 20/23 TSZ02201-0J3J0AC00480-1-2 07.Aug.2013 Rev.001 Datasheet BD9D320EFJ Ordering Information B D 9 D 3 Part Number 2 0 E F J Package EFJ: HTSOP-J8 - E2 Packaging and forming specification E2: Embossed tape and reel Marking Diagram HTSOP-J8 (TOP VIEW) Part Number Marking D 9 D 3 2 0 LOT Number 1PIN MARK www.rohm.co.jp © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111•15•001 21/23 TSZ02201-0J3J0AC00480-1-2 07.Aug.2013 Rev.001 Datasheet BD9D320EFJ Physical Dimension, Tape and Reel Information Package Name HTSOP-J8 Tape Embossed carrier tape Quantity 2500pcs Direction of feed E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand Direction of feed 1pin Reel www.rohm.co.jp © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111•15•001 ) ∗ Order quantity needs to be multiple of the minimum quantity. 22/23 TSZ02201-0J3J0AC00480-1-2 07.Aug.2013 Rev.001 Datasheet BD9D320EFJ Revision History Date Revision 07.Aug.2013 001 Changes Created www.rohm.co.jp © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111•15•001 23/23 TSZ02201-0J3J0AC00480-1-2 07.Aug.2013 Rev.001 Datasheet Notice Precaution on using ROHM Products 1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you (Note 1) , transport intend to use our Products in devices requiring extremely high reliability (such as medical equipment equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅢ CLASSⅣ CLASSⅢ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice - GE © 2014 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act, please consult with ROHM representative in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable for infringement of any intellectual property rights or other damages arising from use of such information or data.: 2. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the information contained in this document. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice - GE © 2014 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s representative. 3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. Notice – WE © 2014 ROHM Co., Ltd. All rights reserved. Rev.001