BH6176GU

1/4 Structure Product Type Functions Silicon Monolithic Integrated Circuit Power Management LSI for MultiMedia LSI on Cellular BH6176GU ・1ch 500mA, high efficiency Step-down Converter. (16 steps adjustable VO by I2C) ・６-channel CMOS-type LDOs. (16 steps adjustable VO by I2C, 150mA×3, 300mA×３) ・LDO and Stepdown converter Power ON/OFF control enabled by I2C interface or external pin ・I2C compatible Interface. (Device address is “1001111”) ・Wafer Level CSP package(2.6mm×2.6mm) for space-constrained applications. Absolute Maximum Ratings（Ta=25C） Parameter Symbol Rating Unit Maximum Supply Voltage (VBAT, PBAT) Maximum Supply Voltage (VUSB) Maximum Supply Voltage (DVDD) Maximum Input Voltage 1 (LX, FB, OUT1, OUT2, OUT3, OUT4, OUT5, OUT6, EN_LD1, EN_LD2, EN_LD3, EN_LD4) Maximum Input Voltage 2 (NRST, CLK, DATA) Power Dissipation VBATMAX VUSBMAX DVDDMAX VINMAX1 VINMAX2 Pd 6.0 6.0 4.5 VBAT + 0.3 DVDD + 0.3 900* 1 V V V V V mW ℃ ℃ Operating Temperature Range Topr -35 ～ +85 Storage Temperature Range Tstg -55 ～ +125 *1 This is the allowable loss of when it is mounted on a ROHM specification board 60mm×60mm. To use at temperature higher than 25C , derate 1% per 1C. Recommended Operating Conditions (Ta=25C) Parameter VBAT, PBAT Voltage VUSB Voltage DVDD Voltage Symbol VBAT VUSB VDVDD * * * 2 2 3 Range 2.20 ～ 5.50 2.20 ～ 5.50 1.70 ～ 4.20 Unit V V V *2 Whenever the VBAT or PBAT or VUSB voltage is under the LDO, SWREG output voltage, the LDO and SWREG output is not guaranteed to meet its published specifications. *3 The DVDD Voltage must be under the Battery Voltage VBAT, PBAT at any times. *This product is not especially designed to be protected from radioactivity. REV. A 2/4 ● Overview Dimensions (VCSP85H2) ● Ball Descriptions Ball No. B4 C4 E1 PIN Name DATA CLK VBAT1 VBAT2 PBAT LX PGND FB NRST OUT1 OUT2 OUT3 OUT4 OUT5 REFC EN_LD1 EN_LD2 EN_LD3 EN_LD4 VUSB DVDD GND TEST OUT6 BH6176 E4 A5 A4 A3 LOT B5 D4 D5 D1 E5 E3 A1 B1 C2 D2 D3 C3 A2 C5 C1 B3 V B G A 0 8 0 V 0 5 0 ( U N I T: m m ) E2 ● Block Diagram DVDD DATA LDO1 1.00-3.30V 16 step init 1.00V OUT1 150mA EN_LD1 I2C IF CLK NRST LDO2 1.00-3.30V 16 step init 2.60V OUT2 150mA EN_LD2 PBAT LX PGND FB LDO3 1.20-3.30V 16 step init 2.80V OUT3 300mA EN_LD3 SWREG 0.8-2.40V 500mA init 1.00V LDO4 1.20-3.30V 16 step init 1.80V OUT4 300mA EN_LD4 VUSB REFC REF LDO5 1.20-3.30V 16 step init 3.30V OUT5 150mA TEST LDO6 TSD 1.20-3.30V 16 step init 2.85V OUT6 300mA REV. A 3/4 Electrical Characteristics (Unless otherwise specified, Ta=25C, VBAT, PBAT=3.6Ｖ, VUSB=5.0V) Parameter ●Circuit Current Circuit Current 1 (OFF) Circuit Current 2 (Standby) IQ1 IQ2 0.4 0.7 1 1.4 μA μA LDO1~6=OFF, SWREG1=OFF, NRST=L, DVDD=0V LDO1~6=OFF, SWREG1=OFF, NRST=H, DVDD=2.6V LDO1~6=ON (no load, initial voltage) SWREG1=ON (no load, initial voltage) NRST=H, DVDD=2.6V VUSB=VBAT external connection Symbol Min. Typ. Max. Unit Condition Circuit Current 3 (Active) IQ3 - 220 380 μA Electrical Characteristics (Unless otherwise specified, Ta=25C, VBAT, PBAT=3.6Ｖ, VUSB=5.0V) Parameter ●Logic pin character Input high level NRST (CMOS input) Input low level Logic input current EN_LD1, EN_LD2, EN_LD3, EN_LD4 (NMOS input) Input high level Input low level Logic input current Input high level CLK, DATA (CMOS input) Input low level Logic input current DATA (CMOS input) ●SWREG SWREG ●LDOs LDO1 Output voltage VOM1 0.97 1.000 1.030 V initial value Io=1mA@VBAT=4.5V Io=150mA@VBAT=3.4V initial value Io=1mA@VBAT=4.5V Io=150mA@VBAT=3.4V initial value Io=1mA@VBAT=4.5V Io=300mA@VBAT=3.4V initial value Io=1mA@VBAT=4.5V Io=300mA@VBAT=3.4V initial value Io=1mA@VUSB=5.5V Io=150mA@VUSB=4.4V initial value Io=1mA@VBAT=4.5V Io=300mA@VBAT=3.4V Output Voltage VOSW 0.94 1.00 1.06 V initial value, Io=100mA Output low level VIH1 VIL1 IIC1 VIH2 VIL2 IIC2 VIH3 VIL3 IIC3 VOL DVDD* 0.7 -0.3 0 1.44 -1 DVDD* 0.8 -0.3 -1 0.3 0 0 DVDD+ 0.3 DVDD* 0.3 1 0.4 1 DVDD+ 0.3 DVDD* 0.2 1 0.4 V V μA V V μA V V μA V IOL=6mA Pin voltage: DVDD Pin voltage: 0 V Symbol Min. Typ. Max. Unit Condition LDO2 Output voltage VOM2 2.522 2.600 2.678 V LDO3 Output voltage VOM3 2.716 2.800 2.884 V LDO4 Output voltage VOM4 1.746 1.800 1.854 V LDO5 Output voltage VOM5 3.201 3.300 3.399 V LDO6 Output voltage VOM6 2.765 2.85 2.936 V REV. A 4/4 ●Use-related Cautions (1) Absolute maximum ratings If applied voltage (VBAT, VADP, VUSB), operating temperature range (Topr), or other absolute maximum ratings are exceeded, there is a risk of damage. Since it is not possible to identify short, open, or other damage modes, if special modes in which absolute maximum ratings are exceeded are assumed, consider applying fuses or other physical safety measures. (2) Recommended operating range This is the range within which it is possible to obtain roughly the expected characteristics. For electrical characteristics, it is those that are guaranteed under the conditions for each parameter. Even when these are within the recommended operating range, voltage and temperature characteristics are indicated. (3) Reverse connection of power supply connector There is a risk of damaging the LSI by reverse connection of the power supply connector. For protection from reverse connection, take measures such as externally placing a diode between the power supply and the power supply pin of the LSI. (4) Power supply lines In the design of the board pattern, make power supply and GND line wiring low impedance. When doing so, although the digital power supply and analog power supply are the same potential, separate the digital power supply pattern and analog power supply pattern to deter digital noise from entering the analog power supply due to the common impedance of the wiring patterns. Similarly take pattern design into account for GND lines as well. Furthermore, for all power supply pins of the LSI, in conjunction with inserting capacitors between power supply and GND pins, when using electrolytic capacitors, determine constants upon adequately confirming that capacitance loss occurring at low temperatures is not a problem for various characteristics of the capacitors used. (5) GND voltage Make the potential of a GND pin such that it will be the lowest potential even if operating below that. In addition, confirm that there are no pins for which the potential becomes less than a GND by actually including transition phenomena. (6) Shorts between pins and misinstallation When installing in the set board, pay adequate attention to orientation and placement discrepancies of the LSI. If it is installed erroneously, there is a risk of LSI damage. There also is a risk of damage if it is shorted by a foreign substance getting between pins or between a pin and a power supply or GND. (7) Operation in strong magnetic fields Be careful when using the LSI in a strong magnetic field, since it may malfunction. (8) Inspection in set board When inspecting the LSI in the set board, since there is a risk of stress to the LSI when capacitors are connected to low impedance LSI pins, be sure to discharge for each process. Moreover, when getting it on and off of a jig in the inspection process, always connect it after turning off the power supply, perform the inspection, and remove it after turning off the power supply. Furthermore, as countermeasures against static electricity, use grounding in the assembly process and take appropriate care in transport and storage. (9) Input pins Parasitic elements inevitably are formed on an LSI structure due to potential relationships. Because parasitic elements operate, they give rise to interference with circuit operation and may be the cause of malfunctions as well as damage. Accordingly, take care not to apply a lower voltage than GND to an input pin or use the LSI in other ways such that parasitic elements operate. Moreover, do not apply a voltage to an input pin when the power supply voltage is not being applied to the LSI. Furthermore, when the power supply voltage is being applied, make each input pin a voltage less than the power supply voltage as well as within the guaranteed values of electrical characteristics. (10) Ground wiring pattern When there is a small signal GND and a large current GND, it is recommended that you separate the large current GND pattern and small signal GND pattern and provide single point grounding at the reference point of the set so that voltage variation due to resistance components of the pattern wiring and large currents do not cause the small signal GND voltage to change. Take care that the GND wiring pattern of externally attached components also does not change. (11) Externally attached capacitors When using ceramic capacitors for externally attached capacitors, determine constants upon taking into account a lowering of the rated capacitance due to DC bias and capacitance change due to factors such as temperature. (12) Thermal shutdown circuit (TSD) When the junction temperature becomes 160°C (typ) or higher, the thermal shutdown circuit operates and turns the switch OFF. The thermal shutdown circuit, which is aimed at isolating the LSI from thermal runaway as much as possible, is not aimed at the protection or guarantee of the LSI. Therefore, do not continuously use the LSI with this circuit operating or use the LSI assuming its operation. (13) Thermal design Perform thermal design in which there are adequate margins by taking into account the permissible dissipation (Pd) in actual states of use. (14) Rush Current Extra care must be taken on power coupling, power, ground line impedance, and PCB design while excess amount of rush current might instantly flow through the power line when powering-up a LSI which is equipped with several power supplies, depending on on/off sequence and ramp delays. REV. A Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2010 ROHM Co., Ltd. All rights reserved. R1010A