BH6627FS

Magnetic disk ICs Read / Write amplifier for FDD BH6627FS The BH6627FS is a 4-mode read / zwrite IC designed for floppy disk drives. This IC has an internal active filter that can be set to any of multiple settings according to transfer rate, and internal switches for density and inner track / outer track. Write current can be set to any of multiple settings. FApplications Floppy disk drives (1MB, 1.6MB and 2MB drives) FFeatures 1) Internal active filter with four settings that can be selected for multiple Q and f0. 2) Time domain filter with internal switch set according to transfer rate. 3) Any of multiple write current settings can be selected, and inner track/outer track switching is done internally. FAbsolute maximum ratings (Ta = 25_C) FRecommended operating conditions 535 Magnetic disk ICs FBlock diagram BH6627FS 536 Magnetic disk ICs FPin descriptions BH6627FS 537 Magnetic disk ICs BH6627FS 538 Magnetic disk ICs BH6627FS 539 Magnetic disk ICs BH6627FS 540 Magnetic disk ICs FElectrical characteristics (unless otherwise noted, Ta = 25_C, VCC = 5V) BH6627FS 541 Magnetic disk ICs BH6627FS 542 Magnetic disk ICs BH6627FS 543 Magnetic disk ICs FRead characteristics BH6627FS Total filter peak frequency setting f0 = a / (RRCC [kΩ] +0.09) [kHz] FILC “H” a = 313 330 376 387 675 844 765 748 “L” 313 330 376 387 627 765 706 754 250 [kbps] outer track 250 [kbps] inner track 300 [kbps] outer track 300 [kbps] inner track 500 [kbps] outer track (when F2 = H) 500 [kbps] inner track (when F2 = H) 500 [kbps] outer track (when F2 = L) 500 [kbps] inner track (when F2 = L) TDF time constant setting 250 [kbps] : T = 758 500 [kbps] : T = 683 500 [kbps] : T = 333 RRCC [kΩ] +604 [ns] RRCC [kΩ] +434 [ns] RRCC [kΩ] +388 [ns] FWrite current switching ratio Write current setting Iwr = 24.0 RWCC [kΩ] [mA] 544 Magnetic disk ICs FFilter characteristic BH6627FS 545 Magnetic disk ICs FMeasurement circuit BH6627FS FCircuit operation (1) Read The input signal from the head coils from each side of the disc is amplified by the preamplifier and then differentiated. The filter time constant can be set externally. After differentiation, the differential output is input to the comparator. The time domain filter detects zero cross, and the output is converted to read data. The monostable multivibrator width can be set externally, while the read data pulse width is a constant 400ns. (2) Write Input write data are converted to toggle movements by the internal flip-flops, operating the write driver. The write driver current is supplied by the write current generator, but the externally set current can be controlled according to density and by selecting inner track/outer track. (3) Erase An open collector output pin is used, and the erase current is set with a resistor between it and the head. (4) Power supply When the low level voltage detector detects a drop in the supply voltage, writing and erasing are prohibited. 546 Magnetic disk ICs FOperation notes (1) Use a short pattern for VCC, and a sufficiently wide AGND and DGND. Keep the impedance between VCC and GND low by inserting a bypass capacitor. (2) Use a pattern that will minimize interference between digital signals and the head. BH6627FS FElectrical characteristic curves 547 Magnetic disk ICs BH6627FS FExternal dimensions (Units: mm) 548