BH6789FVM-GTR

Datasheet DC Brushless Fan Motor Driver 5V Single-phase Full wave Fan motor driver BH6789FVM ●Description This is the summary of models that suit for notebook PC cooling fan motor. They employ Bi-CMOS process and realize low ON resistance, low power consumption and quiet drive. ●Features ■ Compact package (MSOP8) ■ BTL soft switching drive ■ Constant voltage output for hall element ■ Lock protection and auto restart (without external capacitor) ■ Lock alarm signal (AL) output ●Package(s) MSOP8 W(Typ.) x D(Typ.) x H(Max.) 2.90mm x 4.00mm x 0.90mm ●Application ■ Compact 5V fan such as notebook PC cooling fan MSOP8 ●Absolute maximum ratings Symbol Limit Unit Supply voltage Vcc 7 V Power dissipation Pd 585* mW Operating temperature Topr -40 to +105 ℃ Storage temperature Tstg -55 to +150 ℃ Iomax 1000** mA AL signal output voltage Val 7 V AL signal output current Ial 5 mA Tjmax 150 ℃ Parameter Output current Junction temperature * ** Reduce by 4.68mW/℃ over Ta=25ºC(70.0mm×70.0mm×1.6mm glass epoxy board) This value is not to exceed Pd ●Operating conditions Parameter Symbol Limit Unit Operating supply voltage range Vcc 2.0 to 6.0 V Hall input voltage range Vh 0.4 to Vcc-1.1 V ○Product structure：Silicon monolithic integrated circuit ○This product is not designed protection against radioactive rays www.rohm.com TSZ02201-0H1H0B100110-1-2 © 2012 ROHM Co., Ltd. All rights reserved. 1/10 TSZ22111・14・001 11.Jul.2012 Rev.001 Datasheet BH6789FVM ●Electrical characteristics(Unless otherwise specified Ta=25℃,Vcc=5V) Parameter Symbol Limits Unit Conditions Characteristics Min. Typ. Max. Icc - 5 8 mA Fig.1 Vhofs - - ±6 mV - Output voltage Vo - 0.32 0.49 V Input-output Gain Gio 45 48 51 dB AL low voltage Vall - - 0.3 V Lock detection ON time Ton 0.35 0.50 0.65 s Fig.5 Lock detection OFF time Toff 3.5 5.0 6.5 s Fig.6 Hall bias voltage Vhb 1.1 1.3 1.5 V Circuit current Input offset voltage Io＝250mA Upper and Lower total Fig.2,3 - Ial=3mA Ihb=5mA Fig.4 Fig.7 ●Truth table H+ H- OUT1 OUT2 H L H L L H L H AL www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 2/10 normal operation : L(output is ON) lock detection : H(output is OFF) TSZ02201-0H1H0B100110-1-2 11.Jul.2012 Rev.001 Datasheet BH6789FVM ●Reference data 105℃ 25℃ 4 3 Output L voltage [V] Circuit current , Icc [mA] 5 -40℃ 2 1.0 0.0 0.8 -0.2 Output Output H H voltage[V] voltage [V] 6 0.6 105℃ 0.4 25℃ -40℃ 105℃ -0.6 Operating Voltage Range -1.0 0.0 0 0 2 4 6 0.0 8 0.1 0.2 0.3 0.4 0.5 0.6 0.0 0.7 Fig.2 Output L voltage Fig.1 Circuit current 0.3 0.2 2V 0.1 5V 0.8 -40℃ 0.6 25℃ 0.4 105℃ 0.2 Operating Voltage Range 6V 0 1 2 3 4 5 AL current, Ial[mA] Fig.4 AL low voltage 0.4 0.5 0.6 0.7 6.5 -40℃ 6.0 5.5 25℃ 5.0 4.5 105℃ 4.0 3.5 Operating Voltage Range 3.0 0.0 0.0 0.3 7.0 Lock detection OFF time, Toff [s] Lock detection ON time, Ton [s] 0.4 0.2 Fig.3 Output H voltage 1.0 0.5 0.1 Output current, Io [A] Output current, Io[A] Supply voltage, Vcc[ V] AL low low voltage, Vall AL Vall [V] [V] -0.4 -0.8 0.2 1 -40℃ 25℃ 0.0 2.0 4.0 6.0 8.0 0 2 4 6 8 Supply voltage, Vcc[V] Supply voltage, Vcc[V] Fig.5 Lock detection ON time Fig.6 Lock detection OFF time 1.6 105℃ Hall bias voltage, Vhb [V] 25℃ 1.2 -40℃ 0.8 0.4 0.0 0 2 4 6 8 10 Hall bias current, Ihb[mA] Fig.7 Hall bias voltage www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 3/10 TSZ02201-0H1H0B100110-1-2 11.Jul.2012 Rev.001 Datasheet BH6789FVM ●Block diagram, application circuit, and pin assignment M OUT2 GND 1 Incorporates soft switching function. Adjust at an optimum value because gradient of switching of output waveform depends on hall element output. P.5 8 OSC H+ OUT1 2 7 Lock Protection HB HALL TSD P.7 Vcc HALL Bias 3 Take a measure against Vcc voltage rise due to reverse connection of power supply and back electromotive force. 6 H- AL 4 5 This is an open drain output. Connect a pull-up resistor. P.8 OSC : Internal reference oscillation circuit TSD : Thermal shut down(heat rejection circuit) PIN No. Terminal name 1 OUT2 2 H+ Hall input terminal+ 3 HB Hall bias terminal 4 H- Hall input terminal- 5 AL AL signal output terminal 6 Vcc Power supply terminal 7 OUT1 Motor output terminal 1 8 GND GND terminal www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 Function Motor output terminal 2 4/10 TSZ02201-0H1H0B100110-1-2 11.Jul.2012 Rev.001 Datasheet BH6789FVM ●Description of operations 1) Lock protection and automatic restart circuit Motor rotation is detected by hall signal, and lock detection ON time (Ton) and lock detection OFF time (Toff) are set by IC internal counter. External part (C or R) is not required. Timing chart is shown in Fig.8. Idling H+ OUT1 Toff Ton OUT2 Output Tr OFF ON Hi(open collector) AL Motor locking Lock detection Lock Recovers release normal operation Fig.8 Lock protection timing chart 2) Soft switching function (silent drive setting) Input signal to hall amplifier is amplified to produce an output signal. When the hall element output signal is small, the gradient of switching of output waveform is gentle; When it is large, the gradient of switching of output waveform is steep. Enter an appropriate hall element output to IC where output waveform swings sufficiently. (H+)-(H-) OUT1 Fig.9 Relation between hall element output amplitude and output waveform 3) Hall input setting Hall input voltage range is shown in operating conditions. Hall input voltage range Vcc Vcc-1.1V 0.4V GND Fig.10 Hall input voltage range Adjust the value of hall element bias resistor R1 in Fig.11 so that the input voltage of a hall amplifier is input in "hall input voltage range" including signal amplitude. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 5/10 TSZ02201-0H1H0B100110-1-2 11.Jul.2012 Rev.001 Datasheet BH6789FVM ○Reducing the noise of hall signal Hall element may be affected by Vcc noise depending on the wiring pattern of board. In this case, place a capacitor like C1 in Fig.11. In addition, when wiring from the hall element output to IC hall input is long, noise may be loaded on wiring. In this case, place a capacitor like C2 in Fig.11. H+ H- HB C2 C1 RH bias current = Vhb / (RH+R1) R1 Fig.11 Application near of hall signal ●Equivalent circuit 1) Hall input terminal 2) Motor output terminal Vcc OUT1 H+、H- OUT2 GND 3) Hall bias terminal 4) AL output terminal AL HB www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 6/10 TSZ02201-0H1H0B100110-1-2 11.Jul.2012 Rev.001 Datasheet BH6789FVM ●Safety measure 1) Reverse connection protection diode Reverse connection of power results in IC destruction as shown in Fig.12. When reverse connection is possible, reverse connection destruction preventive diode must be added between power supply and Vcc. In normal energization Reverse power connection Vcc After reverse connection destruction prevention Vcc Vcc Circuit block Each pin Circuit block Each pin Circuit block GND Large current flows
Thermal destruction GND Internal circuit impedance high
amperage small Each pin GND No destruction Fig.12 Flow of current when power is connected reversely 2) Measure against Vcc voltage rise by back electromotive force Back electromotive force (Back EMF) generates regenerative current to power supply. However, when reverse connection protection diode is connected, Vcc voltage rises because the diode prevents current flow to power supply. ON ON ON Phase switching ON Fig.13 Vcc voltage rise by back electromotive force When the absolute maximum rated voltage may be exceeded due to voltage rise by back electromotive force, place (A) Capacitor or (B) Zener diode between Vcc and GND. If necessary, add both (C).. (B) Zener diode (A) Capacitor ON ON ON ON (C) Capacitor and zener diode ON ON Fig.14 Measure against Vcc voltage rise www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 7/10 TSZ02201-0H1H0B100110-1-2 11.Jul.2012 Rev.001 Datasheet BH6789FVM 3) Problem of GND line PWM switching Do not perform PWM switching of GND line because the potential of GND terminal cannot be kept at the minimum. Vcc M Motor Driver Controller GND PWM input Prohibited Fig.15 GND Line PWM switching prohibited 4) AL output AL output is an open drain and requires pull-up resistor. The IC can be protected by adding resistor R1. An excess of absolute maximum rating, when AL output terminal is directly connected to power supply, could damage the IC. Vcc Pull-up resistor AL Protection Resistor R1 Connector of board Fig.16 Protection of AL terminal ●Thermal derating curve Thermal derating curve indicates power that can be consumed by IC with reference to ambient temperature. Power that can be consumed by IC begins to attenuate at certain ambient temperature. This gradient is determined by thermal resistance θja. Thermal resistance θja depends on chip size, power consumption, package ambient temperature, packaging condition, wind velocity, etc., even when the same package is used. Thermal derating curve indicates a reference value measured at a specified condition. Fig.17 shows a thermal derating curve (Value when mounting FR4 glass epoxy board 70 [mm] x 70 [mm] x 1.6 [mm] (copper foil area below 3 [%])) Pd(mW) 700 600 585 500 400 300 200 100 0 25 50 75 100 105 125 150 Ta(℃) ＊ Reduce by 4.68 mW/°C over 25°C. (70.0mm×70.0mm×1.6mm glass epoxy board) Fig.17 Thermal derating curve www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 8/10 TSZ02201-0H1H0B100110-1-2 11.Jul.2012 Rev.001 Datasheet BH6789FVM ●Notes for use 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 13) 14) Absolute maximum ratings Devices may be destroyed when supply voltage or operating temperature exceeds the absolute maximum ratings. Because the cause of this damage cannot be identified as a short circuit or an open circuit, if any over rated values will expect to exceed the absolute maximum ratings, consider adding circuit protection devices, such as fuses. Connecting the power supply connector backward Connecting of the power supply in reverse polarity can damage IC. Take precautions when connecting the power supply lines. An external direction diode can be added. Power supply line Back electromotive force causes regenerated current to power supply line, therefore take a measure such as placing a capacitor between power supply and GND for routing regenerated current. And fully ensure that the capacitor characteristics have no problem before determine a capacitor value. (when applying electrolytic capacitors, capacitance characteristic values are reduced at low temperatures) GND potential It is possible that the motor output terminal may deflect below GND terminal because of influence by back electromotive force of motor. The potential of GND terminal must be minimum potential in all operating conditions, except that the levels of the motor outputs terminals are under GND level by the back electromotive force of the motor coil. Also ensure that all terminals except GND and motor output terminals do not fall below GND voltage including transient characteristics. Malfunction may possibly occur depending on use condition, environment, and property of individual motor. Please make fully confirmation that no problem is found on operation of IC. Thermal design Use a thermal design that allows for a sufficient margin in light of the power dissipation(Pd) in actual operating conditions. Inter-pin shorts and mounting errors Use caution when positioning the IC for mounting on printed circuit boards. The IC may be damaged if there is any connection error or if pins are shorted together. Actions in strong electromagnetic field Use caution when using the IC in the presence of a strong electromagnetic field as doing so may cause the IC to malfunction. ASO When using the IC, set the output transistor so that it does not exceed absolute maximum rations or ASO. Thermal shut down circuit The IC incorporates a built-in thermal shutdown circuit (TSD circuit). Operation temperature is 175ºC (typ.) and has a hysteresis width of 25ºC (typ.). When IC chip temperature rises and TSD circuit works, the output terminal becomes an open state. TSD circuit is designed only to shut the IC off to prevent thermal runaway. It is not designed to protect the IC or guarantee its operation. Do not continue to use the IC after operation this circuit or use the IC in an environment where the operation of this circuit is assumed. Testing on application boards When testing the IC on an application board, connecting a capacitor to a pin with low impedance subjects the IC to stress. Always discharge capacitors after each process or step. Always turn the IC’s power supply off before connecting it to or removing it from a jig or fixture during the inspection process. Ground the IC during assembly steps as an antistatic measure. Use similar precaution when transporting or storing the IC. GND wiring pattern When using both small signal and large current GND patterns, it is recommended to isolate the two ground patterns, placing a single ground point at the ground potential of application so that the pattern wiring resistance and voltage variations caused by large currents do not cause variations in the small signal ground voltage. Be careful not to change the GND wiring pattern of any external components, either. Capacitor between output and GND When a large capacitor is connected between output and GND, if Vcc is shorted with 0V or GND for some cause, it is possible that the current charged in the capacitor may flow into the output resulting in destruction. Keep the capacitor between output and GND below 100uF. IC terminal input When Vcc voltage is not applied to IC, do not apply voltage to each input terminal. When voltage above Vcc or below GND is applied to the input terminal, parasitic element is actuated due to the structure of IC. Operation of parasitic element causes mutual interference between circuits, resulting in malfunction as well as destruction in the last. Do not use in a manner where parasitic element is actuated. In use We are sure that the example of application circuit is preferable, but please check the character further more in application to a part which requires high precision. In using the unit with external circuit constant changed, consider the variation of externally equipped parts and our IC including not only static character but also transient character and allow sufficient margin in determining. Status of this document The Japanese version of this document is formal specification. A customer may use this translation version only for a reference to help reading the formal version. If there are any differences in translation version of this document formal version takes priority www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 9/10 TSZ02201-0H1H0B100110-1-2 11.Jul.2012 Rev.001 Datasheet BH6789FVM ●Physical Dimension MSOP8 2.8±0.1 4.0±0.2 8 7 6 5 0.6±0.2 +6° 4° −4° 0.29±0.15 2.9±0.1 (MAX 3.25 include BURR) Tape Embossed carrier tape Quantity 3000pcs Direction of feed TR The direction is the 1pin of product is at the upper right when you hold ( reel on the left hand and you pull out the tape on the right hand ) 1 2 3 4 1PIN MARK 1pin +0.05 0.145 −0.03 0.475 0.08±0.05 0.75±0.05 0.9MAX S +0.05 0.22 −0.04 0.08 S Direction of feed 0.65 Reel (Unit : mm) ∗ Order quantity needs to be multiple of the minimum quantity. ●Marking Diagram MSOP8 (TOP VIEW) Ｈ６７ ８ ９ Lot No. 1PIN MARK www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 10/10 TSZ02201-0H1H0B100110-1-2 11.Jul.2012 Rev.001 Datasheet Notice Precaution on using ROHM Products 1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you (Note 1) , transport intend to use our Products in devices requiring extremely high reliability (such as medical equipment equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅢ CLASSⅣ CLASSⅢ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice - GE © 2014 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act, please consult with ROHM representative in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable for infringement of any intellectual property rights or other damages arising from use of such information or data.: 2. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the information contained in this document. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice - GE © 2014 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s representative. 3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. Notice – WE © 2014 ROHM Co., Ltd. All rights reserved. Rev.001