0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
BH7659FS

BH7659FS

  • 厂商:

    ROHM(罗姆)

  • 封装:

  • 描述:

    BH7659FS - Broadband Triple Circuits Video Signal Switchers - Rohm

  • 数据手册
  • 价格&库存
BH7659FS 数据手册
TECHNICAL NOTE High-performance Video Signal Switchers Broadband Triple Circuits Video Signal Switchers BA7657S/F, BH7659FS ●Description The BA7657S, BA7657F, and BH7659FS are ICs that have been developed for use in PC monitors, HDTVs (high definition televisions), and other high-resolution display devices. In addition to their wide-range switching circuits for RGB signals, HD signals, and VD signals, the BA7657S and BA7657F feature a separation (BUNRI) circuit for the synchronization signal that 2 is superposed on the G signal, while the BH7659FS features an on-chip switch for I C bus signals (SDA and SCL). These ICs can be used to simplify the input block configuration in advanced display devices. ●Features 1) Operates on 5 V single power supply. 2) Built-in wide-range RGB signal switches. (BA7657S/F: fc = 230 MHz) (BH7659FS: fc = 250 MHz) 3) Built-in switching circuit for HD signal and VD signal. 4) Built-in separation (BUNRI) circuit for synchronization signal superposed on G signal. 2 5) Built-in switch for I C bus signals (SDA and SCL). (BH7659FS) 6) Built-in power saving function. (BH7659FS) (BA7657S/F) ●Use PC monitors, Plasma displays, LCD monitors, and Other devices that use wide-range RGB signal switching. ●Lineup Parameter Circuit current (mA) Circuit current during low-power mode (mA) RGB signal SW block frequency characteristics (MHz) Synchronization signal SW block circuit configuration Synchronization signal separation circuit Package BA7657S/F 35 ― 230 2 digital switching circuits SDIP24/SOP24 BH7659FS 25 14 250 4 CMOS analog switching circuits ― SSOP-A32 ●Absolute Maximum Ratings(Ta=25℃) Parameter Symbol Limits Unit Supply voltage 8.0 V VCC BA7657S 1200 Power BA7657F 550 Pd mW dissipation BH7659FS 800 Operating temperature Topr -25~+75 ℃ Storage temperature Tstg -55~+125 ℃ ※Deratings is done at 12mW/℃ (BA7657S), 5.5mW/℃ (BA7657F), 8mW/℃ (BA7659FS) above Ta=25℃. ●Operating Range(Ta=25℃) Parameter Symbol Min. Typ. Max. Unit Supply voltage 4.5 5.0 5.5 V VCC ※This product is not designed for protection against radioactive rays. Aug.2008 ●Electrical characteristics (1/2) BA7657S/F (Unless otherwise noted, Ta=25℃, Vcc=5.0V) Parameter Circuit current 〈Analog SW block〉 Maximum output level Voltage gain Input pin voltage gain differential Inter block voltage gain differential Input pin cross talk1 Interblock crosstalk1 〈Digital SW block〉 “H” “L” “H” “L” level input voltage level input voltage level input current level input current VIH VIL IIH IIL TR TF TRD TFD VOH VOL IOH IOL 1.8 ― 80 -3 ― ― ― ― 3.0 ― -400 5 ― ― 100 -1 30 30 50 30 3.7 0.2 ― ― ― 1.2 130 ― 50 50 80 50 ― 0.4 ― ― V V μA μA ns ns ns ns V V μA mA VIN=5.0V VIN=0V Vom GV △GVl GVB CTI1 CTB1 2.8 -1.0 -0.2 -0.2 ― ― ― -0.5 0 0 -50 -50 ― 0 0.2 0.2 -40 -40 VP-P dB dB dB dB dB f=1kHz f=1MHz,VIN=1VP-P f=1MHz,VIN=1VP-P f=1MHz,VIN=1VP-P f=10MHz,VIN=1VP-P f=10MHz,VIN=1VP-P Symbol ICC Min. 20 Typ. 35 Max. 50 Unit mA Conditions Rise time Fall time Rise delay time Fall delay time “H” “L” “H” “L” level output voltage level output voltage level output current level output current 〈Synchronization signal separation block〉 Minimum SYNC separation level “H” “L” “L” level output voltage level output voltage level output current VSMin. VOH VOL IOL TR TF TRD TFD -50 4.5 ― 2 ― ― ― ― ― 5.0 0.2 ― 80 30 100 100 50 ― 0.5 ― 130 80 150 150 mVP-P V V mA ns ns ns ns Rise time Fall time Rise delay time Fall delay time 〈Control block〉 “H” “L” “H” “L” level input voltage level input voltage level input current level input current VIH VIL IIH IIL 1.8 ― 80 -3 ― ― 100 -1 ― 1.2 130 ― V V μA μA 2/16 ●Electrical characteristics (2/2) BA7657S/F Guaranteed design parameters Parameter 〈Analog SW block〉 Input pin cross talk 2 Interblock cross talk 2 Frequency characteristic Input pin frequency differential Interblock frequency characteristic differential 〈SYNC separation block〉 SYNC separation frequency SYNC separation pulse width 1 SYNC separation pulse width 2 SYNC separation pulse width 3 SYNC separation level 1 SYNC separation level 2 SYNC separation level 3 fH-R pwH1 pwH2 pwH3 VS1 VS2 VS3 200 3.0 0.5 0.3 300 100 60 ― ― ― ― ― ― ― ― ― ― ― ― ― ― kHz μS μS μS μS μS μS Input waveform ※1 Input waveform ※2 fH=20kHz Input waveform ※2 fH=100kHz Input waveform ※2 fH=200kHz Input waveform ※3 fH=20kHz Input waveform ※3 fH=100kHz Input waveform ※3 fH=200kHz CTI2 CTB2 Gf △Gfl △GfB ― ― -6 -1 -1 -30 -30 -3 0 0 -15 -15 -1 +1 +1 dB dB dB dB dB f=230kHz, VIN=1VP-P f=230MHz,VIN=1VP-P f=1MHz/230MHz, VIN=1VP-P f=1MHz/100MHz, VIN=1VP-P f=1MHz/100MHz, VIN=1VP-P Symbol Min. Typ. (Unless otherwise noted, Ta=25℃, Vcc=5.0V) Max. Unit Conditions 〈Input waveform〉 ※1 VS and pwH are variable. VS and pwH are inter-related. See the characteristics diagram. ※2 VS = 130 mW and pwH are variable. ※3 pwH = 1 µs and VS are variable. Period of horizontal synchronization signal DUTY 25% (1H) Vr=0.7V Vs=130mV pwH=1μs 3/16 ●Block diagram BA7657S/F Fig.1 4/16 ●Pin descriptions (1/2) BA7657S/F Pin No. 1 3 5 7 9 11 Pin name Red1 Input Vc c Reference potential Equivalent circuit Function Green1 Input Blue1 Input Red2 Input Green2 Input Blue2 Input V cc 3.7V when selected 0V when not selected 1 00 6.8k 21k 2-channel switching of R, G, and B signals. Select between: CTL: H input1 CTL: L input2 1k 15 19 21 Blue output Green output Red output 2.0V 50 400 5 mA Output pins for RGB signals. Insert resistance from 100 to 300 Ω near the pins to suppress f peaks at high frequencies. Vc c 35k H≧1.8V 16 Control 1k L≦1.2V 50k 15k CTL pins Select between: CTL: H input1 CTL: L input2 12 13 23 24 VD1 input VD2 input HD2 input HD1 input H≧1.8V L≦1.2V 2-channel switching of VD and HD signals. Select between: CTL: H input1 CTL: L input2 14 22 VD output HD output VOH≧3.0V VOL≦10.5V Output pins for vertical synchronization signal (VD) And horizontal synchronization signal (HD). 5/16 ●Pin descriptions (2/2) BA7657S/F Pin No. Pin name Reference potential Equivalent circuit Function 18 Composite Video input 2.5V Input pin for composite signal (Sync on Green). 2 HD Sync Signal detector - This pin is used to detect whether or not the HD signal is being input. When the HD signal is being input, the synchronization signal separation circuit is stopped. Synchronization signal output pin 17 Composite sync output - Synchronization separation is performed for the input signal from pin 18 if the HD signal is not being input. Insert a decoupling capacitor near the pin. 20 VCC 5V - 4 6 8 GND 0V - Use as large a GND pattern area as possible. 6/16 ●Description of operations BA7657S/F 1) Analog SW block Two channels of RGB signals can be switched. I/O relations IN1 can be selected when high-level voltage is applied to Input Output the CTL pin, and IN2 can be selected when low level HD VD Sync on Green HD VD Composite Sync voltage is applied. - - ○ - - ○ 2) Digital SW block ○ - ○ ○ - - This block switches between two channels of HD and VD - ○ ○ - ○ ○ synchronization signals. ○ ○ ○ ○ ○ - HD and VD synchronization signals are output for IN1 when ○ - - ○ - - high-level voltage is applied to the CTL pin, and these signals - ○ - - ○ - are output for IN2 when a low-level voltage is applied to the ○ ○ - ○ ○ - CTL pin. 3) Synchronization signal separation block This block separates composite signals (Sync on Green) and synchronization signals and outputs positive-electrode composite synchronization signals. When an HD signal is being input, the synchronization signal detector operates and stops the synchronization signal separation circuit. A low-level output voltage is used for output. The time at which the synchronization signal separation circuit will be stopped can be set using external time constants for the circuit detection pin. ●Application circuit BA7657S/F Fig.2 7/16 ●Reference data BA7657S/F Vcc=5V BA7657 S/F Analog SW block Vcc=5V BA7657S/F 4.5 4 3.5 3 delay(ns) 2.5 2 1.5 1 0.5 0 -100 -50 0 50 Ta(℃) Analog SW block Vcc=5V 100 150 200 Fig.3 Frequency characteristic BA7657S/F 10 9 PULSE WIDTH : pwH [μs] 8 7 6 5 4 3 2 1 0 20 40 60 80 100 120 140 160 180 200 FREQUENCY : [kHz] Fig.4 Interchannel crosstalk BA7657S/F 50 Vcc=6V Fig.5 Input/output delay time vs. Temperature Circuit  Current(mA ) Duty25% 50mV 130mV 280mV 40 Vcc=5V 30 Vcc=4V 20 10 -50 0 Ta(℃) 50 100 Fig.6 Minimum SYNC separation characteristic Fig.7 Quiescent current vs. Temperature 8/16 ●Electrical characteristics BH7659FS (Unless otherwise noted, Ta=25℃, Vcc=5.0V) Parameter 〈Entire device〉 Circuit current Circuit current during power save 〈R,G,B video SW〉 Voltage gain Interchannel relative gain Interblock relative gain Output dynamic range 〈C-MOS analog SW〉 On-resistance Interchannel ON resistance differential Interchannel cross talk Transmission delay time 〈Control block〉 “H” level voltage “L” level voltage Symbol ICC IPSV Min. 15 7 Typ. 25 14 Max. 35 22 Unit mA mA Conditions - PS=”H” GV △GVC △GVB VOM RON △RON CT tD VH VL -1.0 -0.5 -0.5 2.6 - - - - 3.5 - -0.5 0 0 - 200 20 -70 20 - - 0 0.5 0.5 - 400 40 -55 - - 1.5 dB dB dB VP-P Ω Ω dB ns V V f=10MHz f=10MHz f=10MHz f=1kHz VIN=2.5V VIN=2.5V f=150kHz RL=100Ω,CL=50pF - - ●Guaranteed design parameters BH7659FS (Unless otherwise noted, Ta=25℃, Vcc=5.0V) Parameter 〈R/G/B video SW〉 Frequency characteristics 1 Frequency characteristics 2 Interchannel relative frequency characteristics Interblock relative frequency characteristics Interchannel cross talk 1 Interchannel cross talk 2 Interblock cross talk 1 Interblock cross talk 2 Symbol f1 f2 △fC △fB CTC1 CTC2 CTB1 CTB2 Min. -3.0 -6.0 -0.5 -0.5 - - - - Typ. 0 -3 0 0 -50 -30 -50 -30 Max. +1.0 -1.0 0.5 0.5 -35 -15 -35 -15 Unit dB dB dB dB dB dB dB dB Conditions f=50MHz f=250MHz f=50MHz f=50MHz f=50kHz f=250MHz f=50MHz f=250MHz 9/16 ●Block diagram BH7659FS RINA 1 A 32 RVCC RGND 2 B R 31 ROUT GINA 3 A 30 GVCC GGND 4 B G 29 GOUT BINA 5 A 28 BVCC BGND 6 B B 27 BOUT RINB 7 26 HDOUT PSH 8 POWER SAVE A 25 HDINA GINB 9 B 24 HDINB VDD 10 23 SCLIO BINB 11 A 22 SCLIOA N. C. 1 2 2 1 N. C. CTL 13 B CTL 20 SCLIOB VDINA 14 A A 19 SDAIOA VDINB 15 B B 18 SDAIOB VDOUT 16 17 SDAIO Fig.8 10/16 ●Pin descriptions (1/2) BH7659FS Pin No. 1 3 5 7 9 11 Pin name R chroma signal input pin A (RINA) G chroma signal input pin A (GINA) B chroma signal input pin A (BINA) R chroma signal input pin B (RINB) G chroma signal input pin B (GINB) B chroma signal input pin B (BINB) Reference potential Equivalent circuit VCC Function 3.5V when selected 0V when not selected 3.7V 10k 2k RGB signals are switched in two channels. When selected by SW, the DC potential is approximately 3.5V, and when not selected, the DC potential is about 0 V. VCC 27 29 31 B chroma signal input pin (BOUT) G chroma signal input pin (GOUT) R chroma signal input pin (ROUT) 1.85V 500 2k Power save function is used when PSH pin is set to high level. VCC 8 Power save input pin (PSH) Control input pin (CTL) 0V 3.25V PSH Pin Power save off ≦1.5V Power save on ≧3.5V CTL Pin Input A≧3.5V Input B≦1.5V 13 50k 11/16 ●Pin descriptions (2/2) BH7659FS Pin No. 14 15 16 Pin name VD signal input pin A (VDINA) VD signal input pin B (VDINB) VD signal output pin (VDOUT) SDA signal output pin (SDAIO) SDA signal input pin B (SDAIOB) SDA signal input pin A (SDAIOA) SCL signal input pin B (SCLIOB) SCL signal input pin A (SCLIOA) SCL signal output pin (SCLIO) HD signal input pin B (HDINB) HD signal input pin A (HDINA) HD signal output pin (HDOUT) R GND pin (RGND) G GND pin (GGND) B GND pin (BGND) C-MOS supply voltage pin (VDD) B supply voltage pin (BVCC) G supply voltage pin (GVCC) R supply voltage pin (RVCC) 0V - VDD Reference potential Equivalent circuit Function 17 18 19 IN OUT 0V 20 22 23 24 25 26 VD, HD, SDA, and SCL are switched in two channels. Bidirectional access (I/O) is enabled by the CMOS analog SW. 2 This is the GND pin for the R video SW block. This is the GND pin for the B video SW block. This is the GND pin for the G video SW block , C-MOS SW block. This is the VDD pin for the C-MOS SW block. This is the Vcc pin for the B video SW block This is the Vcc pin for the G video SW block This is the Vcc pin for the R video SW block 4 0V - 6 0V - 10 5V - 28 5V - 30 5V - 32 5V - 12/16 ●Description of operations BH7659FS 1) Analog SW block R, G, and B chroma signals are switched in two channels. INA is selected by applying a high-level voltage to the CTL pin, and INB is selected by applying a low-level voltage. When the power save pin (pin 8) is set to high level, the current to the SW block's output transistors is reduced to lower the circuit current. Even during low power mode, signal switching can be performed normally as long as there is no drop in frequency characteristics. 2) CMOS analog SW block 2 SDA and SDC signals are switched via an I C bus to handle two channels of HD and VD synchronization signals, and to exchange information bidirectionally between a computer and a monitor. 2 The switching circuits used by this IC handle are configured as CMOS analog switches in order to handle I C BUS signals and to transmit input and output signals bidirectionally. (ON resistance: Ron 200 Ω typ.) ●Application circuit BH7659FS Input A R G B VD R4 SDA R4 SCA R4 HD R4 5. 1 5. 1 5. 1 5. 1 R1 R1 C1 + VCC R2 1 A 2 R B 3 A 4 G B 5 A 6 B B 27 28 + VCC 32 + C2 C1 31 Ro C2 R OUT VCC C1 + VCC R2 C2 30 + C1 29 Ro C2 G OUT VCC C1 + VCC R2 C2 R1 C1 Ro C2 B OUT HD OUT Input B R G B VD R4 SDA R4 SCA R4 HD R4 5. 1 R1 5. 1 5. 1 C1 + C1 + VCC R2 7 C2 R1 R4 PS:H C1 5. 1 VCC R1 + 26 R3 A VCC C3 8 POWER SAVE 25 R3 C2 R2 9 B 24 R3 SCL IO 10 C2 C1 C2 VCC R2 11 A 23 R3 22 R3 12 CTL IN A: H IN B: L N. C. N. C. 21 R4 13 C3 R3 A 14 CTL B 20 R3 A 19 R3 R3 B 15 B 18 R3 VD OUT R3 16 SDA IO 17 R3 Fig.9 13/16 ●Reference data 30 BH7659FS 0 -10 BH7659 FS 10 0 GAIN : Gv (dB) -10 -20 -30 -40 -50 BH7659FS Vcc=5V Normal Mode 20 Icc (mA) CROSSTALK : CT(dB) -20 -30 -40 -50 -60 -70 Vcc=5V Power Save Normal Mode 10 Power Save 0 0 1 2 3 4 Vcc (V) 5 6 7 8 -80 1 10 100 1000 FREQUENCY: f(MHz) 1 10 100 FREQUENCY : f (MHz) 1000 Fig.10 Circuit current vs. Supply voltage Fig.11 interchannel crosstalk Fig.12 Frequency characteristics ●Cautions on use (1/2) [BA7657S/F, BH7659FS] 1) Numbers and data in entries are representative design values and are not guaranteed values of the items. 2) Although we are confident in recommending the sample application circuits, carefully check their characteristics further when using them. When modifying externally attached component constants before use, determine them so that they have sufficient margins by taking into account variations in externally attached components and the Rohm LSI, not only for static characteristics but also including transient characteristics. 3) Absolute maximum ratings If applied voltage, operating temperature range, or other absolute maximum ratings are exceeded, the LSI may be damaged. Do not apply voltages or temperatures that exceed the absolute maximum ratings. If you think of a case in which absolute maximum ratings are exceeded, enforce fuses or other physical safety measures and investigate how not to apply the conditions under which absolute maximum ratings are exceeded to the LSI. 4) GND potential Make the GND pin voltage such that it is the lowest voltage even when operating below it. Actually confirm that the voltage of each pin does not become a lower voltage than the GND pin, including transient phenomena. 5) Thermal design Perform thermal design in which there are adequate margins by taking into account the allowable power dissipation in actual states of use. 6) Shorts between pins and misinstallation When mounting the LSI on a board, pay adequate attention to orientation and placement discrepancies of the LSI. If it is misinstalled and the power is turned on, the LSI may be damaged. It also may be damaged if it is shorted by a foreign substance coming between pins of the LSI or between a pin and a power supply or a pin and a GND. 7) Operation in strong magnetic fields Adequately evaluate use in a strong magnetic field, since there is a possibility of malfunction. [BA7657S/F] 8) External resistance for analog SW block The frequency characteristics of analog switches vary according to the output load capacity. Set an external resistance value of R0 to keep frequency characteristics as flat as possible. 9) Polarity of input coupling capacitor When this IC is switched, variation is approximately 3.7 V when the input pin's DC voltage has been selected, but is 0 V when the input pin's DC voltage has not been selected. Therefore, the input coupling capacitor's polarity should be set so as to avoid applying a reverse voltage to capacitors, whether the input pin's DC voltage has been selected or not. 10) High-frequency characteristics of input coupling capacitor Since this IC handles signals at very high frequencies, when using an electrolytic capacitor as a coupling capacitor for input, be sure to insert high-frequency oriented ceramic capacitors (approximately 0.01 µF) in parallel. 11) Layout of target board Since this IC handles signals at very high frequencies, be sure to insert the power supply pin's decoupling capacitor close to the IC's power supply pin. Also, use as large a GND pattern as possible. 12) Switching speed Since this IC changes the DC voltage of input pins when switching, some time is required for switching. The amount of switching time can be determined by time constants that are in turn determined by the capacity of the coupling capacitor connected to the input pin, and the IC's internal input resistance. When using the recommended input coupling capacitor whose capacitance is 47 µF, the switching time is approximately 0.5 seconds. 14/16 ●Cautions on use (2/2) [BH7659FS] 13) External resistance for analog SW block The frequency characteristics of analog switches vary according to the output load capacity. Set an external resistance value of R0 to keep frequency characteristics as flat as possible. 14) Polarity of input coupling capacitor When this IC is switched, variation is approximately 3.5 V when the input pin's DC voltage has been selected, but is 0 V when the input pin's DC voltage has not been selected. Therefore, the input coupling capacitor's polarity should be set so as to avoid applying a reverse voltage to capacitors, whether the input pin's DC voltage has been selected or not. 15) High frequency characteristics of input coupling capacitor Since this IC handles signals at very high frequencies, when using an electrolytic capacitor as a coupling capacitor for input, be sure to insert high-frequency oriented ceramic capacitors (approximately 0.01 µF) in parallel. 16) Layout of target board Since this IC handles signals at very high frequencies, be sure to insert the power supply pin's decoupling capacitor close to the IC's power supply pin. Also, use as large a GND pattern as possible. ●Selection of order type B A 7 6 5 7 S E 2 Part. No. BA7657S BA7657F BH7659FS Tape and Reel information BA7657S ・・・ None(Tube) BA7657F ・・・ E2(Embossed carrier tape) BH7659FS ・・・ E2(Embossed carrier tape) SOP24 Tape Quantity 15.0±0.2 24 13 Embossed carrier tape 2000pcs E2 (The direction is the 1pin of product is at the upper left when you hold reel on the left hand and you pull out the tape on the right hand) 7.8±0.3 5.4±0.2 1 12 1.8±0.1 0.15±0.1 0.11 0.3Min. Direction of feed 1234 1234 1234 1234 1234 1234 1234 1234 1.27 0.4±0.1 0.1 (Unit:mm) Reel 1Pin Direction of feed ※When you order , please order in times the amount of package quantity. 15/16 SDIP24 22.9 ± 0.3 24 13 Container Quantity 6.5 ± 0.3 Tube 1000pcs Direction of products is fixed in a container tube. Direction of feed 7.62 0.51Min. 1 12 3.4 ± 0.2 3.95 ± 0.3 0.3 ± 0.1 1.778 0.5 ± 0.1 0° ∼ 15° (Unit:mm) ※When you order , please order in times the amount of package quantity. SSOP-A32 Tape Quantity 13.6 ± 0.2 32 17 Embossed carrier tape 2000pcs E2 (The direction is the 1pin of product is at the upper left when you hold reel on the left hand and you pull out the tape on the right hand) 1.8 ± 0.1 7.8 ± 0.3 5.4 ± 0.2 Direction of feed 0.3Min. 1 16 0.15 ± 0.1 0.1 0.11 1234 1234 1234 1234 1234 1234 1234 1234 0.8 0.36 ± 0.1 Reel 1pin Direction of feed (Unit:mm) ※When you order , please order in times the amount of package quantity. Catalog No.08T293A '08.8 ROHM © Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of which would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM cannot be held responsible for any damages arising from the use of the products under conditions out of the range of the specifications or due to non-compliance with the NOTES specified in this catalog. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact your nearest sales office. ROHM Customer Support System www.rohm.com Copyright © 2008 ROHM CO.,LTD. THE AMERICAS / EUROPE / ASIA / JAPAN Contact us : webmaster@ rohm.co. jp 21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan TEL : +81-75-311-2121 FAX : +81-75-315-0172 Appendix1-Rev2.0
BH7659FS 价格&库存

很抱歉,暂时无法提供与“BH7659FS”相匹配的价格&库存,您可以联系我们找货

免费人工找货