BH76706GU-E2

Compact Video Driver Series for DSCs and Portable Devices Ultra-compact Waferlevel Chip Size Packeage Output Capacitor-less Single Output Video Drivers No. 09064EAT01 BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU ●Description Due to a built-in charge pump circuit, this video driver does not require the large capacity tantalum capacitor at the video output pin that is essential in conventional video drivers. Features such as a built-in LPF that has bands suited to mobile equipment, current consumption of 0 μA at standby, and low voltage operation from as low as 2.5 V make it optimal for digital still cameras, mobile phones, and other equipment in which high density mounting is demanded. ●Features 1) WLCSP ultra-compact package (1.6 mm x 1.6 mm x 0.75 mm) 2) Improved noise characteristics over BH768xxFVM series 3) Four video driver amplifier gains in lineup: 6 dB, 9 dB, 12 dB, 16.5 dB 4) Large output video driver of maximum output voltage 5.2 Vpp. Ample operation margin for supporting even low voltage operation 5) Output coupling capacitor not needed, contributing to compact design 6) Built-in standby function and circuit current of 0 μA (typ) at standby th 7) Clear image playback made possible by built-in 8 -order 4.5 MHz LPF 8) Due to use of bias input format, supports not only video signals but also chroma signals and RGB signals 9) Due to built-in output pin shunt switch, video output pin can be used as video input pin (BH76706GU) ●Applications Mobile phone, digital still camera, digital video camera, hand-held game, portable media player ●Line up matrix Product Name Video Driver Amplifier Gain Recommended Input Level BH76906GU 6dB 1Vpp BH76909GU 9dB 0.7Vpp BH76912GU 12dB 0.5Vpp BH76916GU 16.5dB 0.3Vpp BH76706GU 6dB 1Vpp ●Absolute Maximum Ratings Video Output Pin Shunt Function ― ○ (Ta = 25 °C) Parameter Symbol Rating Unit Supply voltage Vcc 3.55 V Power dissipation Pd 580 mW Operating temperature range Topr -40～+85 ℃ Storage temperature range Tstg -55～+125 ℃ ＊ When mounted on a 50 mm×58 mm×1.6 mm glass epoxy board, reduce by 5.8mW/°C above Ta=+25°C. www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 1/16 2009.03 - Rev.A BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU Technical Note ●Operating Range Parameter Symbol Min. Typ. Max. Unit Supply voltage Vcc 2.5 3.0 3.45 V ●Electrical Characteristics Parameter Symbol BH76906 GU [Unless otherwise specified, Typ. : Ta = 25 °C, VCC = 3V] Typical Values Unit Measurement Conditions BH76909 BH76912 BH76916 BH76706 GU GU GU GU Circuit current 1-1 ICC1-1 15.0 mA Circuit current 1-2 ICC1-2 17.0 mA Circuit current 2 ICC2 0.0 μA Circuit current 3 ICC3 － IthH1 45 VthH1 1.2V min VthL1 0.45Vmax Standby switch input current High Level Standby switch switching voltage High Level Standby switch switching voltage Low Level Standby switch outflow current High Level Standby switch outflow current Middle Level Standby switch outflow current Low Level Mode switching voltage High Level Mode switching voltage Middle Level Mode switching voltage low Level Voltage gain Maximum output level Frequency characteristic 1 Frequency characteristic 2 Frequency characteristic 3 Frequency characteristic 4 100 － μA In active mode (No signal) In active mode (Outputting NTSC color bar signal) In standby mode In input mode (Applying B3 = 1.5 V) μA Applying B3 = 3.0 V V Active mode V Standby mode IthH2 0 μA Applying B3 = 3.0 V IthM2 8 μA Applying B3 = 1.5 V 23 μA Applying B3 = 0 V V Standby mode V Input mode V Active mode IthL2 － VthM2 VCC -0.2 (MIN.) VCC/2 (TYP.) VthL2 0.2 (MAX.) VthH2 GV Vomv Gf1 Gf2 Gf3 Gf4 6.0 9.0 12.0 5.2 16.5 -0.2 -1.5 -26 -44 6.0 -0.2 -1.4 -28 -48 dB Vpp dB dB dB dB Differential gain DG 0.5 % Differential phase DP 1.0 deg Y signal to noise ratio SNY +74 +73 +70 +70 +74 dB C AM signal to noise ratio SNCA +77 +76 +75 +75 +77 dB C PM signal to noise ratio SNCP +65 dB Current able to flow into output pin lextin 30 mA Output DC offset Voff ±50max mV Input impedance Rin 150 kΩ Output pin shunt switch on resistance Ron www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. － 2/16 3 Vo=100kHz, 1.0Vpp f=10kHz,THD=1% f=4.5MHz/100KHz f=8.0MHz/100KHz f=18MHz/100KHz f=23.5MHz/100KHz Vo=1.0Vp-p Inputting standard staircase Signal Vo=1.0Vp-p Inputting standard staircase signal 100 kHz～6MHz band Inputting 100％ white video signal 100～500 kHz band Inputting 100％ chroma video signal 100～500 kHz band Inputting 100％ chroma video signal Applying 4.5 V to output pin through 150 Ω With no signal Voff = (Vout pin voltage) ÷ 2 Measure inflowing current when applying A3 = 1 V Ω 2009.03 - Rev.A Technical Note BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU ●Test Circuit Diagram A A A 0.01u 10u (VCC) VCC A2 C_PLUS C_PLUS VIN A3 A1 A2 0.1u 1.0uF 150k LPF B3 A 50Ω 150k PUMP STBY STBY OUT 0.1u CHARGE 50Ω B1 VIN A3 IN CHARGE PUMP (VCC) A1 A IN 1.0uF 0.01u 10u VCC OUT B1 A C_MINUS LPF B3 A C_MINUS 100Ω SW2 6dB 6/9/12/16.5dB NVCC NVCC C1 VOUT NVCC C3 C1 V C2 1.0uF V GND 75Ω V V 75Ω SW1 NVCC C2 GND 1.0uF V (a) BH76906/09/12/16GU V V VOUT C3 75Ω (b) BH76706GU Fig. 1 ※ A test circuit is a circuit for shipment inspection and differs from an application circuit example. ●Block Diagram VCC VCC A2 C_PLUS A3 A1 A2 C_PLUS VIN VIN A3 A1 IN IN CHARGE CHARGE 150k PUMP LPF B1 150k PUMP STBY STBY OUT B3 OUT B1 C_MINUS C_MINUS LPF SW2 6dB 6/9/12/16.5dB NVCC NVCC VOUT NVCC C3 C1 C2 B3 SW1 NVCC VOUT C3 C1 GND C2 GND (b) BH76706GU (a) BH76906/09/12/16GU Fig. 2 ●Operation Logic BH769xxGU STBY Pin Logic Operating Mode H Active L Standby OPEN BH76706GU STBY Pin Logic Operating Mode SW1 SW2 Standby OFF OFF H M Input (Record) ON OFF L Active (Playback) OFF ON ※Use of the BH76706GU with the STBY pin OPEN is inappropriate www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 3/16 2009.03 - Rev.A V 75Ω Technical Note BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU ●Pin Descriptions Pin Ball Name Pin Internal Equivalent Circuit Diagram DC Voltage Functional Description VCC VCC C_PLUS A1 Flying capacitor “+” pin +VCC ↑↓ 0V C_PLUS C1 See functional descriptions of 7pin, 8pin GND GND NVCC A2 VCC VCC VCC VCC pin Video signal input pin VIN 0V A3 VIN 100 VIN 43.9k . 1k 43.9k . 1k 150K Suitable input signals include composite video signals, chroma signals, R.G.B. signals NV NVCC BH769xxGU VCC VCC STBY 150k 1μF ACTIVE/STANBY switching pin Pin Voltage MODE 1.2 V～VCC ACTIVE (H) 0 V～0.45 V STANBY (L) 50K 250K 200K GND GND B3 STBY vcc BH76706GU 100K vcc VCC to 0V 200K GND STBY vcc 200K GND MODE switching pin Pin Voltage MODE 2.8 V～VCC (H) STANBY 1.3 V～1.7 V (M) GND (Record) 0 V～0.2 V (L) ACTIVE (Playback) GND NVCC VCC Video signal output pin VCC C3 VOUT VOUT 0V VOUT 75Ω NVCC NVCC 75Ω BH76706GU only GND 1K VCC C2 GND GND 0V GND pin NVCC Note 1) DC voltages in the figure are those when VCC ＝ 3.0 V. Moreover, these values are reference values which are not guaranteed. Note 2) Numeric values in the figure are settings which do not guarantee ratings. www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 4/16 2009.03 - Rev.A Technical Note BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU Flying capacitor “-“ pin (8pin) VCC GND C1 NVCC VCC C_MINUS C2 C1 -VCC (-2.75 V) 0V GND VCC C2 VCC B1 C_MINUS 0V ↑↓ -VCC (-2.75 V) NVCC NVC NVC Negative voltage pin (7pin) Note 1) DC voltages in the figure are those when VCC ＝ 3.0 V. Moreover, these values are reference values which are not guaranteed. Note 2) Numeric values in the figure are settings which do not guarantee ratings. ●Description of Operation 1) Principles of output coupling capacitorless video drivers Single-supply amplifier VCC Dual-supply amplifier Output capacitor required since DC voltage is occurring at output pin VCC 75Ω 1000μF 75Ω Output capacitor not required since DC voltage does not occur at output pin 75Ω 75Ω -VCC 1/2 VCC bias Fig.3 Fig.4 For an amplifier operated from a single power supply (single-supply), since the operating point has a potential of approximately 1/2 Vcc, a coupling capacitor is required for preventing direct current in the output. Moreover, since the load resistance is 150 Ω (75 Ω + 75 Ω) for the video driver, the capacity of the coupling capacitor must be on the order of 1000 μF if you take into account the low band passband. (Fig.3) For an amplifier operated from dual power supplies (+ supply), since the operating point can be at GND level, a coupling capacitor for preventing output of direct current is not needed. Moreover, since a coupling capacitor is not needed, in principle, there is no lowering of the low band characteristic at the output stage. (Fig.4) 2) Occurrence of negative voltage due to charge pump circuit A charge pump, as shown in Fig. 5, consists of a pair of switches (SW1, SW2) and a pair of capacitors (flying capacitor, anchor capacitor). Switching the pair of switches as shown in Fig. 5 causes a negative voltage to occur by shifting the charge in the flying capacitor to the anchor capacitor as in a bucket relay. In this IC, by applying a voltage of +3 V, a negative voltage of approximately -2.8 V is obtained. www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 5/16 2009.03 - Rev.A Technical Note BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU Vcc +3V Vcc +3V Charge current Charge current SW1 + + － SW2 － -Vcc occurs SW1 SW2 － Anchor Capacitor Flying capacitor Charge current Vcc +3V Charging mode + Anchor Capacitor + Flying capacitor Charge shifting mode － + － + － -Vcc occurs Fig.5 Principles of Charge Pump Circuit 3) Configuration of BH769xxGU and BH76706GU As shown in Fig. 6, a BH769xxGU or BH76706GU is a dual-supply amplifier and charge pump circuit integrated in one IC. Accordingly, while there is +3 V single-supply operation, since a dual-supply operation amplifier is used, an output coupling capacitor is not needed. VCC Dual-supply amplifier 1μF 75Ω 150k AMP 75Ω 1-chip integration Although single-supply, output capacitor is not needed. VCC -VCC Charge pump 1μF Charge pump 1μF Fig.6 Configuration Diagram of BH769xxGU or BH76706GU 4) Input pin format and sag characteristic While a BH769xxGU or BH76706GU is a low voltage operation video driver, since it has a large dynamic range of approximately 5.2 Vpp, a resistance termination method that is compatible regardless of signal form (termination by 150 kΩ) is used, and not a clamp method that is an input method exclusively for video signals. Therefore, since a BH769xxGU or BH76706GU operates normally even if there is no synchronization signal in the input signal, it is compatible with not only normal video signals but also chroma signals and R.G.B. signals and has a wide application range. Moreover, concerning sag (lowering of low band frequency) that occurs at the input pin and becomes a problem for the resistance termination method, since the input termination resistor is a high 150 kΩ, even if it is combined with a small capacity input capacitor, a sag characteristic that is not a problem in actual use is obtained. In evaluating the sag characteristic, it is recommended that you use an H-bar signal in which sag readily stands out. (Fig. 8 to Fig. 10) www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 6/16 2009.03 - Rev.A Technical Note BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU Input capacitor and input impedance cutoff frequency is the same as when output capacitor in generic 75 Ω driver is made 1000 μF. 1 μF x 150 kΩ = 1000 μF x 150 Ω (Input pin time constant) (Output pin time constant) Sag is determined by input capacitor and input resistor only. 1μF 150k Sag occurs Fig. 7 a) 75Ω+75Ω=150Ω Video signal without sag (TG-7/1 output, H-bar) TV screen output image of H-bar signal b) Fig. 8 BH769xxGU or BH76706GU output (Input = 1.0 μF, TG-7/1 output, H-bar) Monitor TG-7/1 75Ω 75Ω 150k 1μF BH769xxGU・BH76706GU Fig. 9 Nearly identical sag c) 1000 μF + 150 Ω sag waveform (TG-7/1 output, H-bar) Monitor 75Ω 1000μF 75Ω TG-7/1 Fig. 10 www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 7/16 2009.03 - Rev.A Technical Note BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU ●Application Circuit Example At playback (Active mode) Recording (Input mode) BH76706GU only 2.5～3.45V 2.5～3.45V C4=3.3uF Vcc A2 C_PLUS VIN A3 A1 VIDEO IN STBY B3 LPF B1 C_MINUS C2=1.0uF NVCC C1 NVCC C2 GND C3 SW2 SW1 NVCC Ｒ2＝75Ω VOUT STBY B3 LPF 6dB Video monitor SW1 150k PUMP B1 C_MINUS SW2 6/9/12/16.5dB VIDEO IN CHARGE C1=1.0uF 150k PUMP C3=1.0uF VIN A3 A1 CHARGE C1=1.0uF C4=3.3uF Vcc A2 C_PLUS C3=1.0uF C2=1.0uF CIRCUIT CURREN C1 NVCC C2 C3 GND Ｒ2＝75Ω 75Ω VOUT VIDEO IN VIDEO OUT ＊SW1 and SW2 are built-in BH76706GU only See page 3/16 for STBY pin logic in each mode Fig.11 ※ We are confident in recommending the above application circuit example, but we ask that you carefully check not just the static characteristics but also transient characteristics of this circuit before using it. ●Caution on use 1. Wiring from the decoupling capacitor C4 to the IC should be kept as short as possible. Moreover, this capacitor's capacitance value may have ripple effects on the IC, and may affect the S-N ratio for signals, so we recommend using as large a decoupling capacitor as possible. (Recommended C4: 3.3 µF, B characteristics, 6.3 V or higher maximum voltage) Make mount board patterns follow the layout example shown on page 10 as closely as possible. 2. Capacitors to use In view of the temperature characteristics, etc., we recommend a ceramic capacitor with B characteristics. 3. The NVCC (C1 pin) terminal generates a voltage that is used within the IC, so it should never be connected to a load unless absolutely necessary. Moreover, this capacitor (C2) has a large capacitance value but very little negative voltage ripple. (Recommended C2: 1.0 μF, B characteristic, 6.3 V or higher maximum voltage) 4. Capacitors C1 and C4 should be placed as close as possible to the IC. If the wiring to the capacitor is too long, it can lead to intrusion of switching noise. (Recommended C1: 1.0 µF, B characteristics, 6.3 V or higher maximum voltage) 5. The HPF consists of input coupling capacitor C3 and 150 kΩ of internal input impedance. Be sure to check for video signal sag before determining the C3 value. The cut-off frequency fc can be calculated using the following formula. fc = 1/(2π×C3×150kΩ) (Recommended C3: 1.0 μF, B characteristic, 6.3 V or higher maximum voltage) 6. The output resistor R2 should be placed close to the IC. 7. If the IC is mounted in the wrong direction, there is a risk of damage due to problems such as inverting VCC and GND. Be careful when mounting it. 8. A large current transition occurs in the power supply pin when the charge pump circuit is switched. If this affects other ICs (via the power supply line), insert a resistor (approximately 10 Ω) in the VCC line to improve the power supply's ripple effects. Although inserting a 10 Ω resistor lowers the voltage by about 0.2 V, this IC has a wide margin for low-voltage operation, so dynamic range problems or other problems should not occur. (See Figures 12 to 14.) www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 8/16 2009.03 - Rev.A Technical Note BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU 1. Current ripple due to charge pump circuit affects power supply Vcc pin 10 Ω Vcc Vcc pin 2. Current ripple affects DAC or other 1uF DAC or 1uF 3.3uF VIN VOUT 75Ω VIDEO Other 150k Ω AMP 75Ω -Vcc Chrarge Pump 1uF Fig.12 Effects of Charge Pump Circuit Current Ripple on External Circuit 1) Decoupling capacitor only 1) Decoupling capacitor only Waveform of current between power supply and capacitor (A) 10 mA/div Vcc Waveform of current between capacitor and IC (B) 10 mA/div A A A B Vcc Fig.13 2) Decoupling capacitor + 10 Ω resistor 2) Decoupling capacitor + 10 Ω resistor Waveform of current between power supply and capacitor (A) 10 mA/div Waveform of current between resistor and capacitor (B) 10 mA/div Waveform of current between capacitor and IC (C) 10 mA/div A Vcc 10Ω A A B A C Vcc Fig.14 www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 9/16 2009.03 - Rev.A BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU Technical Note ●Evaluation Board Pattern Diagram (Double-sided, 2 layers) Layer 1 wiring + Silkscreen legend Layer 2 wiring Solder pattern Fig.15 Parts List Symbol C1 C2 C3 Function Flying capacitor Tank capacitor Input coupling capacitor C4 R1 Recommended Value 1μF 1μF 1μF Remarks B characteristic recommended B characteristic recommended B characteristic recommended Decoupling capacitor 3.3μF B characteristic recommended Input termination resistor 75Ω Needed when connected to video signal measurement set R2 Output resistor 75Ω R3 Output termination resistor 75Ω ― Not needed when connected to TV or video signal measurement set Input connector Output connector BNC RCA (Pin jack) www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 10/16 2009.03 - Rev.A Technical Note BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU ●Reference Data BH76906GU BH76906GU Ta=25℃ 25 20 15 10 0.4 20 15 10 5 5 0 0 1 2 3 POWER SUPPLY VOLTAGE [V] 0 40 BH76706GU VCC=3V 80 0.1 0 0 2 BH76706GU Ta=25℃ 0 40 80 100 50 100 50 0 120 2 TEMPERATURE [℃] BH76906GU 2.5 3 3.5 -80 4 -40 POWER SUPPLY VOLTAGE [V] Fig. 19 Standby Circuit Current vs Ambient Temperature VCC=3V 150 0 -40 4 200 150 -0.1 -80 2.5 3 3.5 POWER SUPPLY VOLTAGE [V] Fig. 18 Standby Circuit Current vs Supply Voltage CIRCUIT CURRENT [μA] 0.2 0.1 120 200 CIRCUIT CURRENT [μA] STANDBY CURRENT [uA] -40 Fig. 17 Circuit Current vs Ambient Temperature 0.4 0.3 0.2 TEMPERATURE [℃] Fig. 16 Circuit Current vs Supply Voltage BH76906GU 0.3 -0.1 -80 4 Ta=25℃ BH76906GU STANDBY CURRENT [uA] CIRCUIT CURRENT [mA] 30 CIRCUIT CURRENT [mA] VCC=3V 25 0 40 80 120 TEMPERATURE [℃] Fig. 20 GND Mode Circuit Current vs Supply Voltage Ta=25℃ BH76906GU 5 BH76906GU VCC=3V VCC=3V Ta=25℃ 10 5 -5 -10 -15 2 2.5 3 3.5 POWER SUPPLY VOLTAGE [V] 0 VOLTAGE GAIN [dB] 0 VOUT DC OFFSET [mV] VOUT DC OFFSET [mV] 0 -5 -10 -80 Fig. 22 VOUT Pin Output DC Offset vs Supply Voltage -40 0 40 80 TEMPERATURE [℃] BH76706GU VCC=3V Ta=25℃ -30 -40 -50 -60 -80 1.E+06 120 1.E+07 1.E+08 FREQUENCY [Hz] Fig. 24 Frequency Characteristic Fig. 23 VOUT Pin Output DC Offset vs Ambient Temperature BH76906GU 10 -20 -70 -15 4 -10 VCC=3V BH76906GU Ta=25℃ 6.2 6.2 6.1 6.1 VOLTAGE GAIN [dB] VOLTAGE GAIN [dB] -20 -30 -40 -50 -60 VOLTAGE GAIN [dB] 0 -10 6 5.9 6 5.9 -70 5.8 5.8 -80 1.E+06 1.E+07 1.E+08 FREQUENCY [Hz] Fig. 25 Frequency Characteristic www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 2 2.5 3 3.5 POWER SUPPLY VOLTAGE [V] 4 Fig. 26 Voltage Gain vs Supply Voltage 11/16 -80 -40 0 40 80 120 TEMPERATURE [℃] Fig. 27 Voltage Gainvs Ambient Temperature 2009.03 - Rev.A Technical Note BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU Ta=25℃ BH76906GU 0 -0.2 -0.4 2 2.5 3 3.5 f=4.5MHz/100kHz 0.2 0 -0.2 -0.4 4 -80 -40 VCC=3V f=8MHz/100kHz -4 -5 0 40 80 Ta=25℃ 2 2.5 3 3.5 4 BH76906GU VCC=3V -20 -35 120 3.5 f=18MHz/100kHz -25 -30 -35 4 -80 -40 0 40 80 120 TEMPERATURE [℃] Fig.32 Frequency Characteristic 3 vs Supply Voltage Ta=25℃ BH76906GU VCC=3V BH76906GU -45 f=23.5MHz/100k Hz -50 3.5 MAX OUTPUT VOLTAGE [Vpp] FREQUENCY RESPONSE4:Gf4[dB] -40 -40 -45 f=23.5MHz/100k Hz 6 5 4 3 -50 -80 4 Ta=25℃ 7 -35 -40 POWER SUPPLY VOLTAGE [V] 0 40 80 120 2 2.5 3 3.5 POWER SUPPLY VOLTAGE [V] TEMPERATURE [℃] Fig. 35 Frequency Characteristic 4 vs Ambient Temperature Fig. 34 Frequency Characteristic4 vs Supply Voltage BH76906GU 3 POWER SUPPLY VOLTAGE [V] BH76906GU VCC=3V VCC=3V 6 2.5 Fig. 30 Frequency Characteristic 2 vs Supply Voltage -30 -35 3 -5 POWER SUPPLY VOLTAGE [V] -25 Fig. 31 Frequency Characteristic 2 vs Ambient Temperature 2.5 -4 f=18MHz/100kHz TEMPERATURE [℃] 2 -3 2 FREQUENCY RESPONSE3:Gf3[dB] -2 -40 f=8MHz/100kHz 120 f=18MHz/100kHz -20 -80 80 BH76906GU -1 -3 40 Fig. 29 Frequency Characteristic 1 vs Ambient Temperature FREQUENCY RESPONSE3:Gf3[dB] FREQUENCY RESPONSE2:Gf2[dB] BH76906GU 0 -2 TEMPARATURE [℃] POWER SUPPLY VOLTAGE [V] Fig. 28 Frequency Characteristic 1 vs Supply Voltage Ta=25℃ -1 FREQUENCY RESPONSE2:Gf2[dB] f=4.5MHz/100kHz 0.2 FREQUENCY RESPONSE4:Gf4[dB] BH76906GU 0.4 FREQUENCY RESPONSE1:Gf1[dB] FREQUENCY RESPONSE1:Gf1[dB] 0.4 Ta=25℃ 3 OUTPUT DC VOLTAGE [V] MAX OUTPUT VOLTAGE [Vpp] VCC=3V BH76906GU 5.8 5.6 5.4 5.2 5 2 1 6dB 9dB 12dB 16.5dB 0 -1 -2 -3 -80 -40 0 40 80 120 -1.5 TEMPARATURE [℃] Fig. 37 Max. Output Level vs Ambient Temperature www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. -1.0 - 0.5 0.0 0.5 1.0 1.5 INPUT DC VOLTAGE [V] Fig. 38 DC I/O Characteristic 12/16 2009.03 - Rev.A 4 Technical Note BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU 225 220 215 210 205 200 2 2.5 3 3.5 230 225 220 215 210 205 4 -80 -40 POWER SUPPLY VOLTAGE [V] Ta=25℃ -1 CHARGEPUMP OUTPUT VOLTAGE [V] CHARGEPUMP OUTPUT VOLTAGE [V] 40 80 120 Fig. 40 Charge Pump Oscillation Frequency vs Ambient Temperature -1.5 -2 -2.5 -3 -3.5 BH76906GU -1.0 VCC=3V Ta=25℃ -1.5 -2.0 -2.5 -3.0 -4 2 2.5 3 3.5 POWER SUPPLY VOLTAGE [V] 4 0.0 BH76912GU 10.0 20.0 30.0 40.0 LOAD CURRENT [mA] Fig. 41 Charge Pump Output Voltage vs Supply Voltage Fig. 42 Charge Pump Load Regulation VCC=3V BH76912GU Ta=25℃ 1.2 1.2 DIFFERENTIAL PHASE [Deg] DIFFERENTIAL PHASE [Deg] 0 TEMPERATURE [℃] Fig. 39 Charge Pump Oscillation Frequency vs Supply Voltage BH76906GU VCC=3V BH76906GU Ta=25℃ CHARGEPUMP OSC FREQUENCY [KHz] CHARGEPUMP OSC FREQUENCY [KHz] BH76906GU 230 1.1 1 0.9 0.8 1.1 1 0.9 0.8 2 2.5 3 3.5 POWER SUPPLY VOLTAGE [V] -80 4 -40 0 40 TEMPERATURE [℃] 80 120 Fig. 43 Differential Phase vs Supply Voltage Ta=25℃ BH76912GU DIFFERENTIAL GAIN [%] DIFFERENTIAL GAIN [%] VCC=3V BH76912GU 0.8 0.8 0.6 0.4 0.2 0 0.6 0.4 0.2 0 2 2.5 3 3.5 4 -80 POWER SUPPLY VOLTAGE [V] www.rohm.com 0 40 80 120 TEMPERATURE [℃] Fig. 45 Differential Gain vs Supply Voltage © 2009 ROHM Co., Ltd. All rights reserved. -40 Fig. 46 Differential Gain vs Ambient Temperature 13/16 2009.03 - Rev.A Technical Note BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU Ta=25℃ VCC=3V BH76906GU 79 78.5 78.5 Y S/N [dB] Y S/N [dB] BH76906GU 79 78 78 77.5 77.5 77 77 2 2.5 3 3.5 -80 4 -40 0 POWER SUPPLY VOLTAGE [V] 80 78 CHROMA S/N (AM) [dB] CHROMA S/N (AM) [dB] VCC=3V BH76906GU Ta=25℃ 76 74 72 78 76 74 72 70 70 2 2.5 3 3.5 POWER SUPPLY VOLTAGE [V] -80 4 Fig. 49 C AM S/N vs Supply Voltage -40 0 40 80 TEMPERATURE [℃] 120 Fig. 50 C AM S/N vs Ambient Temperature Ta=25℃ BH76906GU VCC=3V BH76906GU 70 70 68 68 CHROMA S/N (PM) [dB] CHROMA S/N (PM) [dB] 120 Fig.48 Y S/N vs Ambient Temperature 80 66 64 62 66 64 62 60 60 2 2.5 3 3.5 -80 4 -40 40 80 120 Fig. 52 C PM S/N vs Ambient Temperature Fig. 51 C PM S/N vs Supply Voltage Ta=25℃ BH76906GU 0 TEMPERATURE [℃] POWER SUPPLY VOLTAGE [V] VCC=3V BH76906GU 180 165 INPUT IMPEDANCE [kΩ] INPUT IMPEDANCE [kΩ] 80 TEMPERATURE [℃] Fig. 47 Y S/N vs Supply Voltage BH76906GU 40 165 150 135 120 150 135 120 2 2.5 3 3.5 POWER SUPPLY VOLTAGE [V] 4 -80 www.rohm.com 0 40 80 120 TEMPERATURE [℃] Fig. 53 Input Impedance vs Supply Voltage © 2009 ROHM Co., Ltd. All rights reserved. -40 Fig. 54 Input Impedance vs Ambient Temperature 14/16 2009.03 - Rev.A Technical Note BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU BH76906GU BH76706GU VCC=3V Ta=25℃ CIRCUIT CURRENT [mA] 16 CIRCUIT CURRENT [mA] VCC=3V Ta=25℃ 20 20 12 8 4 0 0.0 16 12 8 4 0 0.5 1.0 1.5 2.0 2.5 3.0 0 0.5 CTL TERMINAL VOLTAGE [V] BH76706GU 2 BH76706GU Ta=25℃ 5 2.5 3 VCC=3V 5 4 ON RESISTANCE [Ω] ON RESISTANCE [Ω] 1.5 Fig. 56 Control Pin Characteristic Fig. 55 Control Pin Characteristic 3 2 1 4 3 2 1 2 2.5 3 3.5 -80 4 POWER SUPPLY VOLTAGE [V] -40 0 40 80 120 POWER SUPPLY VOLTAGE [V] Fig. 57 Output Pin Shunt Switch On Resistance vs Supply Voltage ● 1 CTL TERMINAL VOLTAGE [V] Fig. 58 Output Pin Shunt Switch On Resistance vs Ambient Temperature Performing separate electrostatic damage countermeasures When adding an externally attached electrostatic countermeasure element to the output pin, connect a varistor in the position shown in Fig. 59 (if connected directly to the output pin, the IC could oscillate depending on the capacity of the varistor). For this IC, since the output waveform is GND-referenced and swings positive and negative, a normal Zener diode cannot be used. ESD or surge VOUT 75Ω 75Ω Fig.59 Using Externally Attached Varistor www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 15/16 2009.03 - Rev.A Technical Note BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU ●Selection of order type B H 7 6 9 0 6 G U E 2 Tape and Reel information Part. No. BH76906GU BH76909GU BH76912GU BH76916GU BH76706GU VCSP85H1 Tape Embossed carrier tape Quantity 3000pcs Direction of feed 1234 E2 (The direction is the 1pin of product is at the upper left when you hold reel on the left hand and you pull out the tape on the right hand) 1234 Reel (Unit:mm) www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 1234 1234 1pin 1234 1234 Direction of feed ※When you order , please order in times the amount of package quantity. 16/16 2009.03 - Rev.A Datasheet Notice Precaution on using ROHM Products 1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you (Note 1) , transport intend to use our Products in devices requiring extremely high reliability (such as medical equipment equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅢ CLASSⅣ CLASSⅢ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice - GE © 2014 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act, please consult with ROHM representative in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable for infringement of any intellectual property rights or other damages arising from use of such information or data.: 2. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the information contained in this document. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice - GE © 2014 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s representative. 3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. Notice – WE © 2014 ROHM Co., Ltd. All rights reserved. Rev.001