BH76912GU

Compact Video Driver Series for DSCs and Portable Devices Ultra-compact Waferlevel Chip Size Packeage Output Capacitor-less Single Output Video Drivers BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU No. 09064EAT01 ●Description Due to a built-in charge pump circuit, this video driver does not require the large capacity tantalum capacitor at the video output pin that is essential in conventional video drivers. Features such as a built-in LPF that has bands suited to mobile equipment, current consumption of 0 μA at standby, and low voltage operation from as low as 2.5 V make it optimal for digital still cameras, mobile phones, and other equipment in which high density mounting is demanded. ●Features 1) WLCSP ultra-compact package (1.6 mm x 1.6 mm x 0.75 mm) 2) Improved noise characteristics over BH768xxFVM series 3) Four video driver amplifier gains in lineup: 6 dB, 9 dB, 12 dB, 16.5 dB 4) Large output video driver of maximum output voltage 5.2 Vpp. Ample operation margin for supporting even low voltage operation 5) Output coupling capacitor not needed, contributing to compact design 6) Built-in standby function and circuit current of 0 μA (typ) at standby th 7) Clear image playback made possible by built-in 8 -order 4.5 MHz LPF 8) Due to use of bias input format, supports not only video signals but also chroma signals and RGB signals 9) Due to built-in output pin shunt switch, video output pin can be used as video input pin (BH76706GU) ●Applications Mobile phone, digital still camera, digital video camera, hand-held game, portable media player ●Line up matrix Product Name BH76906GU BH76909GU BH76912GU BH76916GU BH76706GU ●Absolute Maximum Ratings Parameter Supply voltage Power dissipation Operating temperature range Storage temperature range (Ta = 25 °C) Symbol Vcc Pd Topr Tstg Rating 3.55 580 -40～+85 -55～+125 Unit V mW ℃ ℃ Video Driver Amplifier Gain 6dB 9dB 12dB 16.5dB 6dB Recommended Input Level 1Vpp 0.7Vpp 0.5Vpp 0.3Vpp 1Vpp ○ ― Video Output Pin Shunt Function ＊ When mounted on a 50 mm×58 mm×1.6 mm glass epoxy board, reduce by 5.8mW/°C above Ta=+25°C. www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 1/16 2009.03 - Rev.A BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU ●Operating Range Parameter Supply voltage Symbol Vcc Min. 2.5 Typ. 3.0 Max. 3.45 Unit V Technical Note ●Electrical Characteristics Parameter Circuit current 1-1 Circuit current 1-2 Circuit current 2 Circuit current 3 Standby switch input current High Level Standby switch switching voltage High Level Standby switch switching voltage Low Level Standby switch outflow current High Level Standby switch outflow current Middle Level Standby switch outflow current Low Level Mode switching voltage High Level Mode switching voltage Middle Level Mode switching voltage low Level Voltage gain Maximum output level Frequency characteristic 1 Frequency characteristic 2 Frequency characteristic 3 Frequency characteristic 4 Differential gain Differential phase Y signal to noise ratio C AM signal to noise ratio C PM signal to noise ratio Current able to flow into output pin Output DC offset Input impedance Output pin shunt switch on resistance Symbol ICC1-1 ICC1-2 ICC2 ICC3 IthH1 VthH1 VthL1 IthH2 IthM2 IthL2 － VthH2 VthM2 VthL2 GV Vomv Gf1 Gf2 Gf3 Gf4 DG DP SNY SNCA SNCP lextin Voff Rin Ron － +74 +77 +73 +76 6.0 9.0 -0.2 -1.5 -26 -44 0.5 1.0 +70 +75 +65 30 ±50max 150 3 +70 +75 +74 +77 12.0 5.2 16.5 － 45 1.2V min 0.45Vmax 0 8 23 VCC -0.2 (MIN.) VCC/2 (TYP.) 0.2 (MAX.) BH76906 GU [Unless otherwise specified, Typ. : Ta = 25 °C, VCC = 3V] Typical Values Unit Measurement Conditions BH76909 BH76912 BH76916 BH76706 GU GU GU GU mA mA 15.0 17.0 0.0 100 μA μA μA － V V μA μA μA V V V dB Vpp dB dB dB dB % deg dB dB dB mA mV kΩ Ω In active mode (No signal) In active mode (Outputting NTSC color bar signal) In standby mode In input mode (Applying B3 = 1.5 V) Applying B3 = 3.0 V Active mode Standby mode Applying B3 = 3.0 V Applying B3 = 1.5 V Applying B3 = 0 V Standby mode Input mode Active mode Vo=100kHz, 1.0Vpp f=10kHz,THD=1% f=4.5MHz/100KHz f=8.0MHz/100KHz f=18MHz/100KHz f=23.5MHz/100KHz Vo=1.0Vp-p Inputting standard staircase Signal Vo=1.0Vp-p Inputting standard staircase signal 100 kHz～6MHz band Inputting 100％ white video signal 6.0 -0.2 -1.4 -28 -48 100～500 kHz band Inputting 100％ chroma video signal 100～500 kHz band Inputting 100％ chroma video signal Applying 4.5 V to output pin through 150 Ω With no signal Voff = (Vout pin voltage) ÷ 2 Measure inflowing current when applying A3 = 1 V www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 2/16 2009.03 - Rev.A BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU ●Test Circuit Diagram Technical Note A 10u VCC C_PLUS A1 IN CHARGE 50Ω 1.0uF B1 C_MINUS 6/9/12/16.5dB NVCC V C1 1.0uF C2 GND NVCC VOUT C3 V 75Ω V 75Ω V NVCC C1 1.0uF NVCC PUMP OUT LPF 150k STBY B3 A B1 C_MINUS SW2 6dB SW1 1.0uF A2 VIN A3 C_PLUS 0.1u A A1 IN CHARGE PUMP OUT LPF 150k A2 0.01u A (VCC) 10u VCC 0.01u A (VCC) VIN A3 0.1u A 50Ω STBY B3 A 100Ω V V VOUT C3 C2 GND V 75Ω V 75Ω (a) BH76906/09/12/16GU Fig. 1 ※ (b) BH76706GU A test circuit is a circuit for shipment inspection and differs from an application circuit example. ●Block Diagram VCC A2 VIN A3 IN CHARGE PUMP OUT B1 C_MINUS 6/9/12/16.5dB NVCC C1 C2 GND NVCC VOUT C3 NVCC C1 C2 GND NVCC LPF 150k STBY B3 B1 C_MINUS C_PLUS A1 IN CHARGE PUMP OUT LPF 150k STBY B3 VCC A2 VIN A3 C_PLUS A1 SW2 6dB SW1 VOUT C3 (a) BH76906/09/12/16GU Fig. 2 (b) BH76706GU ●Operation Logic BH769xxGU STBY Pin Logic H L OPEN Operating Mode Active Standby BH76706GU STBY Pin Logic H M L Operating Mode Standby Input (Record) Active (Playback) SW1 OFF ON OFF SW2 OFF OFF ON ※Use of the BH76706GU with the STBY pin OPEN is inappropriate www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 3/16 2009.03 - Rev.A BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU ●Pin Descriptions Pin Ball Name C_PLUS Technical Note Pin Internal Equivalent Circuit Diagram VCC VCC DC Voltage Functional Description A1 Flying capacitor “+” pin C_PLUS C1 +VCC ↑↓ 0V See functional descriptions of 7pin, 8pin GND GND NVCC A2 VCC VCC VCC VCC pin Video signal input pin 0V A3 VIN VIN 100 3 . 1k 4 .9k 3.9k 4 . 1k VIN 1μF Suitable input signals include composite video signals, chroma signals, R.G.B. signals ACTIVE/STANBY switching pin Pin Voltage MODE 1.2 V～VCC ACTIVE (H) 0 V～0.45 V STANBY (L) 150k 150K NVCC NV VCC VCC BH769xxGU STBY 50K 250K 200K GND GND B3 STBY BH76706GU 100K vcc 200K GND vcc VCC to 0V MODE switching pin Pin Voltage 2.8 V～VCC (H) 1.3 V～1.7 V (M) 0 V～0.2 V (L) MODE STANBY STBY vcc GND (Record) ACTIVE (Playback) 200K GND GND NVCC VCC VCC Video signal output pin C3 VOUT NVCC NVCC VOUT 0V VOUT 75Ω 75Ω BH76706GU only 1K GND VCC C2 GND NVCC GND 0V GND pin Note 1) DC voltages in the figure are those when VCC ＝ 3.0 V. Moreover, these values are reference values which are not guaranteed. Note 2) Numeric values in the figure are settings which do not guarantee ratings. www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 4/16 2009.03 - Rev.A BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU Technical Note Flying capacitor “-“ pin (8pin) VCC GND C1 NVCC VCC C_MINUS C2 C1 -VCC (-2.75 V) 0V GND VCC VCC C2 0V ↑↓ -VCC (-2.75 V) B1 C_MINUS NVCC NVC Negative voltage pin (7pin) NVC Note 1) DC voltages in the figure are those when VCC ＝ 3.0 V. Moreover, these values are reference values which are not guaranteed. Note 2) Numeric values in the figure are settings which do not guarantee ratings. ●Description of Operation 1) Principles of output coupling capacitorless video drivers Single-supply amplifier VCC Output capacitor required since DC voltage is occurring at output pin 75Ω 1000μF 75Ω -VCC Dual-supply amplifier VCC Output capacitor not required since DC voltage does not occur at output pin 75Ω 75Ω 1/2 VCC bias Fig.3 Fig.4 For an amplifier operated from a single power supply (single-supply), since the operating point has a potential of approximately 1/2 Vcc, a coupling capacitor is required for preventing direct current in the output. Moreover, since the load resistance is 150 Ω (75 Ω + 75 Ω) for the video driver, the capacity of the coupling capacitor must be on the order of 1000 μF if you take into account the low band passband. (Fig.3) For an amplifier operated from dual power supplies (+ supply), since the operating point can be at GND level, a coupling capacitor for preventing output of direct current is not needed. Moreover, since a coupling capacitor is not needed, in principle, there is no lowering of the low band characteristic at the output stage. (Fig.4) 2) Occurrence of negative voltage due to charge pump circuit A charge pump, as shown in Fig. 5, consists of a pair of switches (SW1, SW2) and a pair of capacitors (flying capacitor, anchor capacitor). Switching the pair of switches as shown in Fig. 5 causes a negative voltage to occur by shifting the charge in the flying capacitor to the anchor capacitor as in a bucket relay. In this IC, by applying a voltage of +3 V, a negative voltage of approximately -2.8 V is obtained. www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 5/16 2009.03 - Rev.A BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU Vcc +3V Charge current Vcc +3V Charge current Technical Note SW1 + SW1 － SW2 + Anchor Capacitor SW2 － -Vcc occurs Charge current Flying capacitor － Anchor Capacitor Flying capacitor + Vcc +3V Charging mode Charge shifting mode + － + － + － -Vcc occurs Fig.5 Principles of Charge Pump Circuit 3) Configuration of BH769xxGU and BH76706GU As shown in Fig. 6, a BH769xxGU or BH76706GU is a dual-supply amplifier and charge pump circuit integrated in one IC. Accordingly, while there is +3 V single-supply operation, since a dual-supply operation amplifier is used, an output coupling capacitor is not needed. VCC 1μF 150k AMP Dual-supply amplifier 75Ω 75Ω 1-chip integration Although single-supply, output capacitor is not needed. VCC -VCC Charge pump 1μF Charge pump 1μF Fig.6 Configuration Diagram of BH769xxGU or BH76706GU 4) Input pin format and sag characteristic While a BH769xxGU or BH76706GU is a low voltage operation video driver, since it has a large dynamic range of approximately 5.2 Vpp, a resistance termination method that is compatible regardless of signal form (termination by 150 kΩ) is used, and not a clamp method that is an input method exclusively for video signals. Therefore, since a BH769xxGU or BH76706GU operates normally even if there is no synchronization signal in the input signal, it is compatible with not only normal video signals but also chroma signals and R.G.B. signals and has a wide application range. Moreover, concerning sag (lowering of low band frequency) that occurs at the input pin and becomes a problem for the resistance termination method, since the input termination resistor is a high 150 kΩ, even if it is combined with a small capacity input capacitor, a sag characteristic that is not a problem in actual use is obtained. In evaluating the sag characteristic, it is recommended that you use an H-bar signal in which sag readily stands out. (Fig. 8 to Fig. 10) www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 6/16 2009.03 - Rev.A BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU Sag is determined by input capacitor and input resistor only. 1μF 150k Technical Note Input capacitor and input impedance cutoff frequency is the same as when output capacitor in generic 75 Ω driver is made 1000 μF. 1 μF x 150 kΩ = 1000 μF x 150 Ω (Input pin time constant) (Output pin time constant) 75Ω+75Ω=150Ω Fig. 7 a) Video signal without sag (TG-7/1 output, H-bar) Sag occurs TV screen output image of H-bar signal b) Fig. 8 BH769xxGU or BH76706GU output (Input = 1.0 μF, TG-7/1 output, H-bar) Monitor 1μF 150k TG-7/1 75Ω 75Ω BH769xxGU・BH76706GU Fig. 9 Nearly identical sag c) 1000 μF + 150 Ω sag waveform (TG-7/1 output, H-bar) Monitor 75Ω 1000μF TG-7/1 75Ω Fig. 10 www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 7/16 2009.03 - Rev.A BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU ●Application Circuit Example At playback (Active mode) 2.5～3.45V Vcc C_PLUS A1 CHARGE C1=1.0uF B1 C_MINUS PUMP LPF SW2 6/9/12/16.5dB Technical Note Recording (Input mode) BH76706GU only 2.5～3.45V C4=3.3uF VIN A3 C3=1.0uF C_PLUS A1 VIDEO IN 150k STBY B3 Video monitor C3 VOUT VIDEO OUT Ｒ2＝75Ω CIRCUIT CURREN C2=1.0uF C1=1.0uF B1 C_MINUS CHARGE PUMP A2 Vcc C4=3.3uF VIN A3 C3=1.0uF A2 VIDEO IN 150k LPF SW2 6dB STBY B3 SW1 C3 Ｒ2＝75Ω 75Ω C2=1.0uF NVCC C1 SW1 NVCC C1 NVCC C2 GND NVCC C2 GND VOUT VIDEO IN ＊SW1 and SW2 are built-in BH76706GU only Fig.11 ※ See page 3/16 for STBY pin logic in each mode We are confident in recommending the above application circuit example, but we ask that you carefully check not just the static characteristics but also transient characteristics of this circuit before using it. ●Caution on use 1. Wiring from the decoupling capacitor C4 to the IC should be kept as short as possible. Moreover, this capacitor's capacitance value may have ripple effects on the IC, and may affect the S-N ratio for signals, so we recommend using as large a decoupling capacitor as possible. (Recommended C4: 3.3 µF, B characteristics, 6.3 V or higher maximum voltage) Make mount board patterns follow the layout example shown on page 10 as closely as possible. Capacitors to use In view of the temperature characteristics, etc., we recommend a ceramic capacitor with B characteristics. The NVCC (C1 pin) terminal generates a voltage that is used within the IC, so it should never be connected to a load unless absolutely necessary. Moreover, this capacitor (C2) has a large capacitance value but very little negative voltage ripple. (Recommended C2: 1.0 μF, B characteristic, 6.3 V or higher maximum voltage) 2. 3. 4. Capacitors C1 and C4 should be placed as close as possible to the IC. If the wiring to the capacitor is too long, it can lead to intrusion of switching noise. (Recommended C1: 1.0 µF, B characteristics, 6.3 V or higher maximum voltage) 5. The HPF consists of input coupling capacitor C3 and 150 kΩ of internal input impedance. Be sure to check for video signal sag before determining the C3 value. The cut-off frequency fc can be calculated using the following formula. fc = 1/(2π×C3×150kΩ) (Recommended C3: 1.0 μF, B characteristic, 6.3 V or higher maximum voltage) 6. The output resistor R2 should be placed close to the IC. 7. If the IC is mounted in the wrong direction, there is a risk of damage due to problems such as inverting VCC and GND. Be careful when mounting it. 8. A large current transition occurs in the power supply pin when the charge pump circuit is switched. If this affects other ICs (via the power supply line), insert a resistor (approximately 10 Ω) in the VCC line to improve the power supply's ripple effects. Although inserting a 10 Ω resistor lowers the voltage by about 0.2 V, this IC has a wide margin for low-voltage operation, so dynamic range problems or other problems should not occur. (See Figures 12 to 14.) www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 8/16 2009.03 - Rev.A BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU 1. Current ripple due to charge pump circuit affects power supply Vcc pin Vcc 10 Ω Technical Note 1uF 2. Current ripple affects DAC or other 1uF VIN VIDEO AMP 150k Ω Vcc pin 3.3uF VOUT 75Ω DAC or Other 75Ω -Vcc Chrarge Pump 1uF Fig.12 Effects of Charge Pump Circuit Current Ripple on External Circuit 1) Decoupling capacitor only 1) Decoupling capacitor only Waveform of current between power supply and capacitor (A) 10 mA/div Waveform of current between capacitor and IC (B) 10 mA/div AB Vcc Vcc A A Fig.13 2) Decoupling capacitor + 10 Ω resistor 2) Decoupling capacitor + 10 Ω resistor Waveform of current between power supply and capacitor (A) 10 mA/div Waveform of current between resistor and capacitor (B) 10 mA/div Waveform of current between capacitor and IC (C) 10 mA/div A C Vcc Vcc 10Ω A B A A Fig.14 www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 9/16 2009.03 - Rev.A BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU ●Evaluation Board Pattern Diagram (Double-sided, 2 layers) Technical Note Layer 1 wiring + Silkscreen legend Layer 2 wiring Solder pattern Fig.15 Parts List Symbol C1 C2 C3 C4 R1 R2 R3 Function Flying capacitor Tank capacitor Input coupling capacitor Decoupling capacitor Input termination resistor Output resistor Output termination resistor Input connector Output connector Recommended Value 1μF 1μF 1μF 3.3μF 75Ω 75Ω 75Ω BNC RCA (Pin jack) Remarks B characteristic recommended B characteristic recommended B characteristic recommended B characteristic recommended Needed when connected to video signal measurement set ― Not needed when connected to TV or video signal measurement set www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 10/16 2009.03 - Rev.A BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU ●Reference Data BH76906GU Ta=25℃ BH76906GU VCC=3V BH76906GU 0.4 Technical Note Ta=25℃ 30 CIRCUIT CURRENT [mA] CIRCUIT CURRENT [mA] 25 STANDBY CURRENT [uA] 25 20 15 10 5 0 0 1 2 3 POWER SUPPLY VOLTAGE [V] 4 20 0.3 0.2 15 0.1 10 0 5 -80 -40 0 40 80 120 TEMPERATURE [℃] -0.1 2 2.5 3 3.5 POWER SUPPLY VOLTAGE [V] 4 Fig. 16 Circuit Current vs Supply Voltage BH76906GU VCC=3V Fig. 17 Circuit Current vs Ambient Temperature BH76706GU Ta=25℃ Fig. 18 Standby Circuit Current vs Supply Voltage BH76706GU VCC=3V 0.4 STANDBY CURRENT [uA] 200 CIRCUIT CURRENT [μA] CIRCUIT CURRENT [μA] 200 0.3 0.2 0.1 0 -0.1 -80 -40 0 40 80 120 TEMPERATURE [℃] 150 150 100 100 50 50 0 2 2.5 3 3.5 4 POWER SUPPLY VOLTAGE [V] 0 -80 -40 0 40 80 120 TEMPERATURE [℃] Fig. 19 Standby Circuit Current vs Ambient Temperature Fig. 20 GND Mode Circuit Current vs Supply Voltage BH76906GU Ta=25℃ BH76906GU VCC=3V BH76906GU VCC=3V Ta=25℃ 5 5 10 0 VOUT DC OFFSET [mV] VOUT DC OFFSET [mV] VOLTAGE GAIN [dB] 0 0 -10 -20 -30 -40 -50 -60 -70 -5 -5 -10 -10 -15 2 2.5 3 3.5 POWER SUPPLY VOLTAGE [V] 4 - 15 -80 -40 0 40 80 TEMPERATURE [℃] 120 -80 1.E+06 FREQUENCY [Hz] 1.E+07 1.E+08 Fig. 22 VOUT Pin Output DC Offset vs Supply Voltage Fig. 23 VOUT Pin Output DC Offset vs Ambient Temperature BH76906GU Ta=25℃ Fig. 24 Frequency Characteristic 10 0 -10 VOLTAGE GAIN [dB] BH76706GU BH76906GU 6.2 VCC=3V VCC=3V Ta=25℃ 6.2 6.1 6.1 VOLTAGE GAIN [dB] -20 -30 -40 -50 -60 -70 - 80 1.E+06 6 VOLTAGE GAIN [dB] 6 5.9 5.9 5 .8 5 .8 2 2.5 3 3.5 POWER SUPPLY VOLTAGE [V] 4 FREQUENCY [Hz] 1.E+07 1.E+08 -80 -40 0 40 80 120 TEMPERATURE [℃] Fig. 25 Frequency Characteristic www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. Fig. 26 Voltage Gain vs Supply Voltage Fig. 27 Voltage Gainvs Ambient Temperature 11/16 2009.03 - Rev.A BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU BH76906GU FREQUENCY RESPONSE1:Gf1[dB] Ta=25℃ BH76906GU VCC=3V BH76906GU Technical Note Ta=25℃ 0.4 f=4.5MHz/100kHz FREQUENCY RESPONSE1:Gf1[dB] 0.4 f=4.5MHz/100kHz FREQUENCY RESPONSE2:Gf2[dB] -1 0.2 0.2 -2 f=8MHz/100kHz 0 0 -3 -0.2 -0.2 -4 - 0.4 2 2.5 3 3.5 4 POWER SUPPLY VOLTAGE [V] - 0.4 -80 -40 0 40 80 120 TEMPARATURE [℃] -5 2 2.5 3 3.5 4 POWER SUPPLY VOLTAGE [V] Fig. 28 Frequency Characteristic 1 vs Supply Voltage Fig. 29 Frequency Characteristic 1 vs Ambient Temperature Fig. 30 Frequency Characteristic 2 vs Supply Voltage BH76906GU FREQUENCY RESPONSE2:Gf2[dB] VCC=3V -20 BH76906GU Ta=25℃ f=18MHz/100kHz f=18MHz/100kHz FREQUENCY RESPONSE3:Gf3[dB] -20 BH76906GU VCC=3V -1 FREQUENCY RESPONSE3:Gf3[dB] f=18MHz/100kHz -2 -25 -25 -3 f=8MHz/100kHz -30 -30 -4 -5 -80 -40 0 40 80 120 -35 2 2.5 3 3.5 4 - 35 -80 -40 0 40 80 120 TEMPERATURE [℃] POWER SUPPLY VOLTAGE [V] TEMPERATURE [℃] Fig. 31 Frequency Characteristic 2 vs Ambient Temperature BH76906GU -35 Fig.32 Frequency Characteristic 3 vs Supply Voltage BH76906GU -35 Ta=25℃ VCC=3V 7 BH76906GU Ta=25℃ FREQUENCY RESPONSE4:Gf4[dB] FREQUENCY RESPONSE4:Gf4[dB] MAX OUTPUT VOLTAGE [Vpp] 6 -40 -40 5 -45 -45 4 f=23.5MHz/100k Hz -50 2 2.5 3 3.5 4 f=23.5MHz/100k Hz -50 -80 -40 0 40 80 120 3 2 2.5 3 3.5 4 POWER SUPPLY VOLTAGE [V] TEMPERATURE [℃] POWER SUPPLY VOLTAGE [V] Fig. 34 Frequency Characteristic4 vs Supply Voltage BH76906GU 6 Fig. 35 Frequency Characteristic 4 vs Ambient Temperature VCC=3V 3 VCC=3V Ta=25℃ MAX OUTPUT VOLTAGE [Vpp] 5.8 OUTPUT DC VOLTAGE [V] 2 1 0 -1 -2 -3 5.6 5.4 6dB 9dB 12dB 16.5dB 5.2 5 -80 -40 0 40 80 120 -1.5 -1.0 - 0.5 0.0 0.5 1.0 1.5 TEMPARATURE [℃] INPUT DC VOLTAGE [V] Fig. 37 Max. Output Level vs Ambient Temperature www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. Fig. 38 DC I/O Characteristic 12/16 2009.03 - Rev.A BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU BH76906GU CHARGEPUMP OSC FREQUENCY [KHz] Ta=25℃ CHARGEPUMP OSC FREQUENCY [KHz] BH76906GU Technical Note VCC=3V 230 225 220 215 210 205 200 2 2.5 3 3.5 4 POWER SUPPLY VOLTAGE [V] 230 225 220 215 210 205 -80 -40 TEMPERATURE [℃] 0 40 80 120 Fig. 39 Charge Pump Oscillation Frequency vs Supply Voltage BH76906GU CHARGEPUMP OUTPUT VOLTAGE [V] Ta=25℃ Fig. 40 Charge Pump Oscillation Frequency vs Ambient Temperature -1.0 BH76906GU VCC=3V Ta=25℃ -1.5 -2 -2.5 -3 -3.5 -4 2 POWER SUPPLY VOLTAGE [V] CHARGEPUMP OUTPUT VOLTAGE [V] -1 -1.5 -2.0 -2.5 -3.0 2.5 3 3.5 4 0.0 10.0 20.0 30.0 40.0 LOAD CURRENT [mA] Fig. 41 Charge Pump Output Voltage vs Supply Voltage BH76912GU Ta=25℃ Fig. 42 Charge Pump Load Regulation BH76912GU VCC=3V 1.2 DIFFERENTIAL PHASE [Deg] DIFFERENTIAL PHASE [Deg] 1.2 1.1 1.1 1 1 0.9 0.9 0.8 2 POWER SUPPLY VOLTAGE [V] 0.8 2.5 3 3.5 4 -80 -40 TEMPERATURE [℃] 0 40 80 120 Fig. 43 Differential Phase vs Supply Voltage BH76912GU 0.8 Ta=25℃ 0.8 BH76912GU VCC=3V DIFFERENTIAL GAIN [%] DIFFERENTIAL GAIN [%] 0.6 0.6 0.4 0.4 0.2 0.2 0 2 2.5 3 3.5 4 0 -80 -40 0 40 80 120 POWER SUPPLY VOLTAGE [V] TEMPERATURE [℃] Fig. 45 Differential Gain vs Supply Voltage www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. Fig. 46 Differential Gain vs Ambient Temperature 13/16 2009.03 - Rev.A BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU BH76906GU Ta=25℃ BH76906GU Technical Note VCC=3V 79 79 78.5 Y S/N [dB] 78.5 Y S/N [dB] 78 78 77.5 77.5 77 2 2.5 3 3.5 4 77 -80 -40 0 40 80 120 POWER SUPPLY VOLTAGE [V] TEMPERATURE [℃] Fig. 47 Y S/N vs Supply Voltage Fig.48 Y S/N vs Ambient Temperature VCC=3V BH76906GU Ta=25℃ 80 BH76906GU 80 CHROMA S/N (AM) [dB] CHROMA S/N (AM) [dB] 78 78 76 76 74 74 72 72 70 2 2.5 3 3.5 POWER SUPPLY VOLTAGE [V] 4 70 -80 -40 0 40 80 TEMPERATURE [℃] 120 Fig. 49 C AM S/N vs Supply Voltage Fig. 50 C AM S/N vs Ambient Temperature BH76906GU Ta=25℃ BH76906GU VCC=3V 70 68 66 64 62 60 2 2.5 3 3.5 4 POWER SUPPLY VOLTAGE [V] 70 68 66 64 62 60 -80 -40 0 40 80 120 TEMPERATURE [℃] CHROMA S/N (PM) [dB] CHROMA S/N (PM) [dB] BH76906GU Ta=25℃ Fig. 51 C PM S/N vs Supply Voltage Fig. 52 C PM S/N vs Ambient Temperature BH76906GU VCC=3V 180 165 INPUT IMPEDANCE [kΩ] 165 INPUT IMPEDANCE [kΩ] 150 150 135 135 120 2 POWER SUPPLY VOLTAGE [V] 1 20 2.5 3 3.5 4 -80 -40 0 40 80 120 TEMPERATURE [℃] Fig. 53 Input Impedance vs Supply Voltage www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. Fig. 54 Input Impedance vs Ambient Temperature 14/16 2009.03 - Rev.A BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU BH76906GU VCC=3V Ta=25℃ BH76706GU Technical Note VCC=3V Ta=25℃ 20 CIRCUIT CURRENT [mA] 20 16 12 8 4 0 0.5 1.0 1.5 2.0 2.5 3.0 16 CIRCUIT CURRENT [mA] 12 8 4 0 0.0 0 0.5 CTL TERMINAL VOLTAGE [V] CTL TERMINAL VOLTAGE [V] 1 1.5 2 2.5 3 Fig. 55 Control Pin Characteristic Fig. 56 Control Pin Characteristic BH76706GU 5 Ta=25℃ BH76706GU 5 VCC=3V ON RESISTANCE [Ω] 3 ON RESISTANCE [Ω] 4 4 3 2 2 1 2 2.5 3 3.5 4 POWER SUPPLY VOLTAGE [V] 1 -80 -40 0 40 80 120 POWER SUPPLY VOLTAGE [V] Fig. 57 Output Pin Shunt Switch On Resistance vs Supply Voltage ● Fig. 58 Output Pin Shunt Switch On Resistance vs Ambient Temperature Performing separate electrostatic damage countermeasures When adding an externally attached electrostatic countermeasure element to the output pin, connect a varistor in the position shown in Fig. 59 (if connected directly to the output pin, the IC could oscillate depending on the capacity of the varistor). For this IC, since the output waveform is GND-referenced and swings positive and negative, a normal Zener diode cannot be used. ESD or surge VOUT 75Ω 75 Ω Fig.59 Using Externally Attached Varistor www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 15/16 2009.03 - Rev.A BH76906GU, BH76909GU, BH76912GU, BH76916GU, BH76706GU ●Selection of order type Technical Note B H 7 6 9 0 6 G U E 2 Part. No. BH76906GU BH76909GU BH76912GU BH76916GU BH76706GU Tape and Reel information VCSP85H1 Tape Embossed carrier tape E2 (The direction is the 1pin of product is at the upper left when you hold reel on the left hand and you pull out the tape on the right hand) Quantity 3000pcs Direction of feed 1234 1234 1234 1234 1234 1234 Reel (Unit:mm) 1pin Direction of feed ※When you order , please order in times the amount of package quantity. www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 16/16 2009.03 - Rev.A Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. R0039A