Datasheet
AC/DC Drivers
PWM type DC/DC converter IC
Included 650V MOSFET
BM2P016T
●General
The PWM type DC/DC converter (BM2P016T) for
AC/DC provides an optimum system for all products
that include an electrical outlet.
BM2P016T supports both isolated and non-isolated
devices, enabling simpler design of various types of
low-power electrical converters.
BM2P016T builds in a HV starter circuit that tolerates
650V, and it contributes to low-power consumption.
With current detection resistors for switching as
external devices, a higher degree of design freedom is
achieved. Since current mode control is utilized, current
is restricted in each cycle and excellent performance is
demonstrated in bandwidth and transient response. The
switching frequency is 65 kHz. At light load, the
switching frequency is reduced and high efficiency is
achieved. A frequency hopping function is also on chip,
which contributes to low EMI. We can design easily,
because BM2P016T includes the switching MOSFET.
●Features
PWM frequency : 65kHz
PWM current mode method
Frequency hopping function
Burst operation at light load
Frequency reduction function
Built-in 650V start circuit
Built-in 650V switching MOSFET
VCC pin under voltage protection
VCC pin over voltage protection
SOURCE pin Open protection
SOURCE pin Short protection
SOURCE pin Leading-Edge-Blanking function
Per-cycle over current protection circuit
AC Correction function of over current limiter
Soft start function
Secondary over current protection circuit
●Package
TO220-7M 10.0mm×25.4mm×4.6mm
(Typ.)
(Typ.) (Max.)
●Basic specifications
Operating Power Supply Voltage Range
VCC: 8.9V to 26.0V
DRAIN: to 650V
Operating Current:
Normal Mode: 0.950mA (Typ.)
Burst Mode: 0.300mA (Typ.)
Oscillation Frequency:
65kHz(Typ.)
o
o
Operating Temperature:
- 40 C to +105 C
MOSFET ON Resistance:
1.4Ω (Typ.)
●Applications
AC adapters and household appliances (vacuum
cleaners, humidifiers, air cleaners, air conditioners, IH
cooking heaters, rice cookers, etc.)
●Application circuit
Figure 1. Application Circuit
○Product structure：Silicon monolithic integrated circuit
.www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・14・001
○This product is not designed protection against radioactive rays
1/18
TSZ02201-0F1F0A200240-1-2
18.Apr.2017.Rev.003
Datasheet
BM2P016T
●Absolute Maximum Ratings（Ta=25C）
Parameter
Maximum applied voltage 1
Maximum applied voltage 2
Maximum applied voltage 3
Drain current pulse
Allowable dissipation
Operating temperature range
MAX junction temperature
Storage temperature range
Symbol
Vmax1
Vmax2
Vmax3
IDP
Pd
Topr
Tjmax
Tstr
Rating
-0.3 to 32.0
-0.3 to 6.5
650
10.40
1.50
-40 to +105
150
-55 to +150
Unit
V
V
V
A
W
o
C
o
C
o
C
Conditions
VCC
SOURCE, FB, FADJ
DRAIN
PW=10us, Duty cycle=1%
(Note1) Derate by 12mW/°C when operating above Ta = 25°C when mounted
Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit
between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated over the
absolute maximum ratings.
●Operating Conditions（Ta=25C）
Parameter
Power supply voltage range 1
Power supply voltage range 2
Symbol
VCC
VDRAIN
Rating
8.9 to 26.0
650
Unit
V
V
Conditions
VCC pin voltage
DRAIN pin voltage
●Electrical Characteristics of MOSFET part (Unless otherwise noted, Ta = 25C, VCC = 15 V)
Parameter
Min
Specifications
Typ
Max
V(BR)DDS
650
-
-
V
ID=1mA / VGS=0V
IDSS
RDS(ON)
-
1.4
100
2.0
uA
Ω
VDS=650V / VGS=0V
ID=0.25A / VGS=10V
Symbol
Unit
Conditions
[MOSFET Block ]
Between drain and
Source voltage
Drain leak current
On resistance
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
2/18
TSZ02201-0F2F0A200240-1-2
18.Apr.2017.Rev.003
Datasheet
BM2P016T
●Electrical Characteristics (unless otherwise noted, Ta = 25C, VCC = 15 V)
Specifications
Parameter
Symbol
Min
Typ
Max
[Circuit Current]
Circuit current (ON) 1
Circuit current (ON) 2
Unit
Conditions
ION1
ION2
700
200
950
300
1200
400
μA
μA
FB=2.0(at pulse operation)
FB=0.0V(at burst operation)
VUVLO1
VUVLO2
VUVLO3
VOVP1
VOVP2
VOVP3
VCHG1
VCHG2
TLATCH
TSD1
TSD2
12.50
7.50
26.0
22.0
7.70
12.00
50
120
90
13.50
8.20
5.30
27.5
23.5
4.0
8.70
13.00
100
145
115
14.50
8.90
29.0
25.0
9.70
14.00
150
170
140
V
V
VCC rise
VCC fall
VUVLO3= VUVLO1- VUVLO2
VCC rise
VCC fall
VOVP3= VOVP1- VOVP2
C
C
FSW1
FSW2
FDEL1
FCH
IBST
VBST
FBST
TSS1
TSS2
TSS3
TSS4
Dmax
Tmin
RFB
Gain
VBST1
VBST2
VBST3
60
20
75
0.80
1.13
0.30
0.60
1.20
4.80
68.0
150
23
3.00
0.220
0.260
-
65
25
0.833
125
1.00
1.20
0.833
0.50
1.00
2.00
8.00
75.0
400
30
4.00
0.280
0.320
0.040
70
30
175
1.20
1.27
0.70
1.40
2.80
11.20
82.0
650
37
7.00
0.340
0.380
-
KHz
KHz
KHz
Hz
uA
V
KHz
ms
ms
ms
ms
%
ns
kΩ
V/V
V
V
V
VDLT
1.100
1.250
1.400
V
VFOLP1A
VFOLP1B
TFOLP1
TFOLP2
2.60
2.40
80
332
2.80
2.60
128
512
3.00
2.80
176
692
V
V
ms
ms
Overload is detected (FB rise)
Overload is detected (FB fall)
VSOURCE
0.375
0.050
0.080
0.130
0.230
(120)
0.400
0.100
0.150
0.200
0.300
250
0.425
0.150
0.220
0.270
0.370
(380)
V
V
V
V
V
ns
Ton=0us
0[ms] to Tss1 [ms]
TSS1 [ms] to TSS2 [ms]
TSS2 [ms] to TSS3 [ms]
TSS3 [ms] to TSS4 [ms]
Design assurance
[VCC Protection Function]
VCC UVLO voltage 1
VCC UVLO voltage 2
VCC UVLO hysteresis
VCC OVP voltage 1
VCC OVP voltage 2
VCC OVP hysteresis
VCC recharge start voltage
VCC recharge stop voltage
Latch mask time
Thermal shut down temperature1
Thermal shut down temperature2
V
V
V
V
V
us
Control IC, temp rise
Control IC, temp fall
[PWM Type DCDC Driver Block]
Oscillation frequency 1
Oscillation frequency 2
Frequency hopping width 1
Hopping fluctuation frequency
FADJ source current
FADJ comparator voltage
FADJ max burst frequency
Soft start time 1
Soft start time 2
Soft start time 3
Soft start time 4
Maximum duty
Minimum ON time
FB pin pull-up resistance
ΔFB / ΔSOURCE gain
FB burst voltage 1
FB burst voltage 2
FB burst hysteresis
FB voltage of
starting frequency reduction mode
FB OLP voltage 1a
FB OLP voltage 1b
FB OLP ON time
FB OLP OFF time
FB=2.00V
FB=0.30V
FB=2.00V
FADJ=0.00V
CFADJ=1000pF
FB fall
FB rise
VBST3= VBST2 - VBST1
[Over Current Detection Block]
Over-current detection voltage
Over-current detection voltage SS1
Over-current detection voltage SS2
Over-current detection voltage SS3
Over-current detection voltage SS4
Leading edge blanking time
Over current detection AC voltage
compensation factor
SOURCE pin short protection voltage
SOURCE pin short protection time
VS_SS1
VS_SS2
VS_SS3
VS_SS4
TLEB
KSOURCE
12
20
28
mV/us
VSHT
0.020
1.80
0.050
3.00
0.080
4.20
V
us
TSOURCESHT
[Circuit Current]
Start current 1
Start current 2
ISTART1
ISTART2
0.100
1.000
0.500
3.000
1.000
6.000
mA
mA
OFF current
ISTART3
-
10
20
uA
VSc
0.800
1.500
2.100
V
Start current switching voltage
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
3/18
VCC=0V
VCC=10V
Inflow current from Drain pin after
UVLO is released and when
MOSFET is OFF
TSZ02201-0F2F0A200240-1-2
18.Apr.2017.Rev.003
Datasheet
BM2P016T
●Pin Descriptions
Table 1. Pin Description
NO.
Pin Name
I/O
1
2
3
4
5
6
7
DRAIN
SOURCE
N.C.
FADJ
GND
FB
VCC
I/O
I/O
I
I/O
I
I
Function
MOSFET DRAIN pin
MOSFET SOURCE pin
MAX Burst Frequency setting pin
GND pin
Feedback signal input pin
Power supply input pin
ESD Diode
VCC
GND
○
○
○
○
○
○
○
○
●I/O Equivalent Circuit Diagram
Figure 2. I/O Equivalent Circuit Diagram
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
4/18
TSZ02201-0F2F0A200240-1-2
18.Apr.2017.Rev.003
Datasheet
BM2P016T
●Block Diagram
FUSE
AC
Diode
Bridge
Filter
7
1
VCC UVLO
+
-
VCC OVP
100us
Filter
+
-
Starter
4.0V
Line Reg
Clamp
Circuit
Internal Block
4
Burst
Frequency
Control
S
R
DRIVER
Q
PWM Control
+
Burst Control
Internal Reg.
Internal Reg.
OLP
6
+
OLP
Timer
Current
Limiter
Burst
Comparator
Leading Edge
Blanking
+
-
2
+
AC Input
Compensation
Soft Start
PWM
Comparator
-
MAX
DUTY
+
+
OSC
5
Frequency
Hopping
Slope
Compensation
FeedBack
With
Isolation
Figure 3. Block Diagram
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
5/18
TSZ02201-0F2F0A200240-1-2
18.Apr.2017.Rev.003
Datasheet
BM2P016T
●Block Description
(1) Start circuit
This IC has a built-in start circuit. It enables low standby mode electricity and high speed start.
After start up, consumption power is determined by idling current ISTART3 （Typ=10uA） only.
Reference values of starting time are shown in Figure 6. When Cvcc=10uF it can start in less than 0.1 sec.
+
FUSE
AC
85- 265 Vac
Diode
Bridge
-
DRAIN
SW1
VCC
Cvcc
+
VCCUVLO
Figure 4. Block Diagram of Start Circuit
1.0
0.9
0.8
0.7
0.6
[sec]
0.5
0.4
起 動時間
0.3
0.2
0.1
0.0
0
5
10
15
20
25
30
35
40
45
50
Cvcc [uF]
Figure 5. Start Current vs VCC Voltage
Figure 6. Start Time (reference value)
* Start current flows from the DRAIN pin
Ex) Consumption power of start circuit only when Vac=100V
PVH＝100V*√2*10uA=1.41mW
Ex) Consumption power of start circuit only when Vac=240V
PVH＝240V*√2*10uA=3.38mW
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
6/18
TSZ02201-0F2F0A200240-1-2
18.Apr.2017.Rev.003
Datasheet
BM2P016T
(2) Start sequences
(Soft start operation, light load operation, and auto recovery operation during overload protection)
Start sequences are shown in Figure 7. See the sections below for detailed descriptions.
Figure 7. Start Sequences Timing Chart
A:
B:
C:
D:
E:
F:
G:
H:
I:
J:
K:
Input voltage VH is applied.
This IC starts operating when VCC > VUVLO1 (13.5V Typ).
Switching function starts when other protection functions are judged as normal.
When the secondary output voltage becomes constant, VCC pin current causes the VCC voltage to drop. As a result, IC
should be set to start switching until VCCVUVLO1 and when the DC/DC operation starts. The VCC pin voltage then
drops to VCHG2. The operation is shown in figure 8.
VH
VUVLO1
VCHG2
VCC VCHG1
VUVLO2
Switching
VH charge
charge
charge charge charge
OUTPUT
voltage
A
B C D E
F G H
Figure 8. VCC Pin Charge Operation
A:
B:
C:
D:
E:
F:
G:
H:
DRAIN pin voltage rises, charges VCC pin through the VCC charge function.
VCC > VUVLO1, VCC UVLO function releases, VCC charge function stops, DC/DC operation starts.
When the DC/DC operation starts, the VCC voltage drops.
VCC < VCHG1, VCC recharge function operates.
VCC > VCHG2, VCC recharge function stops.
VCC < VCHG1, VCC recharge function operates.
VCC > VCHG2, VCC recharge function stops.
After the output voltage is finished rising, VCC is charged by the auxiliary winding, and VCC pin stabilizes.
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
8/18
TSZ02201-0F2F0A200240-1-2
18.Apr.2017.Rev.003
Datasheet
BM2P016T
(4) DCDC driver (PWM comparator, frequency hopping, slope compensation, OSC, burst)
This IC has a current mode PWM control.
An internal oscillator sets a fixed switching frequency (65 kHz Typ).
This IC has an integrated switching frequency hopping function, which causes the switching frequency to fluctuate as
shown in Figure 10 below.
The fluctuation cycle is 125 Hz (Typ).
Figure 9.
Frequency Hopping Function
Maximum duty cycle is fixed at 75% (Typ) and minimum pulse width is fixed at 400 ns (Typ).
In current mode control, sub-harmonic oscillation may occur when the duty cycle exceeds 50%.
As a countermeasure, this IC has built-in slope compensation circuits.
This IC has built-in burst mode and frequency reduction circuits to achieve lower power consumption when the load is light.
FB pin is pulled up by RFB (30kΩ Typ).
FB pin voltage is changed by secondary output voltage (secondary load power).
FB pin is monitored, burst mode operation and frequency detection start.
Figure 10 shows the FB voltage, and the DCDC switching frequency operation.
・mode1 : Burst operation
・mode2 : Frequency reduction operation
・mode3 : Fixed frequency operation (operates at max frequency)
・mode4 : Overload operation (detects the overload state and stops the pulse operation)
Figure 10.
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
Switching Operation State Changes by FB Pin Voltage
9/18
TSZ02201-0F2F0A200240-1-2
18.Apr.2017.Rev.003
Datasheet
BM2P016T
(4-1) MAX Burst frequency setting
This IC can reduce a burst sound to fix a burst frequency.
This IC has two clocks, so this IC can fix the burst frequency.
Frequency
[kHz]
Burst
Mode
Frequency
Reduction Mode
Frequency
[kHz]
Normal
Mode
65kHz
Burst
Mode
Frequency
Reduction Mode
Normal
Mode
65kHz
Switching
frequency
Switching
frequency
25kHz
25kHz
[Region of sound]
[Region of sound]
FADJ
Burst frequency
Burst frequency
Output Power[W]
Output Power[W]
Figure 11-1. No setting
Figure 11-2. setting
Setting external capacitor of FADJ pin, the burst frequency is fixed.
It is showed an example of max burst frequency setting using FADJ pin
This frequency is decided by FADJ source current, FADJ comparator voltage and external capacitor.
100000
Burst Frequency [Hz]
10000
1000
100
10
10
100
1000
10000
C_FADJ[pF]
Figure 12. Example of max burst frequency setting using FADJ pin
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
10/18
TSZ02201-0F2F0A200240-1-2
18.Apr.2017.Rev.003
Datasheet
BM2P016T
(5) Over Current limiter
This IC has a built-in over current limiter per cycle. If the SOURCE pin exceeds a certain voltage, switching stops. It also has
a built-in AC voltage compensation function. With this function, the over current limiter level is high until the time the AC
voltage is compensated.
Shown in figure-13, 14, and 15
Figure 13. No AC Voltage Compensation Function
Figure 14. Built-in AC Compensation Voltage
Primary peak current is calculated using the formula below.
Primary peak current: Ipeak = Vsource /Rs + Vdc/Lp*Tdelay
Vcs： Over current limiter voltage (internal), Rs：Current detection resistance, Vdc： Input DC voltage, Lp：Primary inductance.
Tdelay： Delay time after detection of over current limiter
Figure 15. Over Current Limiter Voltage
（6）L. E. B. Blanking Period
When the MOSFET driver is turned ON, surge current flows through each capacitor component and drive current is
generated. Therefore, when the SOURCE pin voltage rises temporarily, detection errors may occur in the over current
limiter circuit. To prevent detection errors, DRAIN is switched from high to low and the SOURCE signal is masked for
250ns by the on-chip LEB (Leading Edge Blanking) function.
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
11/18
TSZ02201-0F2F0A200240-1-2
18.Apr.2017.Rev.003
Datasheet
BM2P016T
(7) SOURCE pin short protection function
When the SOURCE pin is shorted, This IC overheats.
This IC has a built-in short protection function to prevent destruction.
(8) SOURCE pin open protection
If the SOURCE pin becomes OPEN, This IC may be damaged.
To prevent it from being damaged, This IC has a built-in OPEN protection circuit （auto recovery protection）.
(9) Output over load protection function （FB OLP Comparator）
The output overload protection function monitors the secondary output load status at the FB pin and stops switching
whenever overload occurs. When there is an overload, the output voltage is reduced and current no longer flows to the
photo coupler, so the FB pin voltage rises.
When the FB pin voltage > VFOLP1A (2.8V Typ) continuously for the period TFOLP (128ms Typ), it is judged as an overload and
switching stops.
When the FB pin > VFOLP1A (2.8V Typ), if the voltage goes lower than VFOLP1B (2.6V Typ) during the period TFOLP (128ms Typ),
the overload protection timer is reset. The switching operation is performed during this period TFOLP (128ms Typ).
At startup, the FB voltage is pulled up to the IC’s internal voltage, so operation starts at a voltage of VFOLP1A (2.8V Typ) or
above. Therefore, at startup the FB voltage must be set to VFOLP1B (2.6V Typ) or below during the period TFOLP (128ms Typ),
and the secondary output voltage’s start time must be set within the period TFOLP (128ms Typ) following startup of the IC.
Recovery is after the period TFOLP2(512ms Typ), from the detection of FBOLP.
●Operation mode of protection circuit
Operation mode of protection functions are shown in Table 2.
Table 2.
Operation Mode of Protection Circuit
Function
Operation mode
VCC Under Voltage Locked Out
Auto recovery
VCC Over Voltage Protection
Auto recovery
TSD
Auto recovery
FB Over Limited Protection
SOURCE Short Protection
SOURCE Open Protection
Auto recovery
Auto recovery
Auto recovery
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
12/18
TSZ02201-0F2F0A200240-1-2
18.Apr.2017.Rev.003
Datasheet
BM2P016T
● Thermal loss
The thermal design should set operation for the following conditions.
(Since the temperature shown below is the guaranteed temperature, be sure to take a margin into account.)
1. The ambient temperature Ta must be 105℃ or less.
2. The IC’s loss must be within the allowable dissipation Pd.
The thermal abatement characteristics are as follows.
2.0
Pd[W]
1.5
1.0
0.5
0.0
0
25
50
75
100
125
150
Ta[℃]
Figure 16. Thermal Abatement Characteristics
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
13/18
TSZ02201-0F2F0A200240-1-2
18.Apr.2017.Rev.003
Datasheet
BM2P016T
●Ordering Information
B
M
2
P
0
6
1
T
-
Package
T: TO220-7M
Product name
Packaging and forming specification
None : Tube
●Physical Dimension Tape and Reel Information
TO220-7M
Container
Tube
Quantity
238pcs
500pcs
Direction of feed
Direction of products is fixed in a container tube
∗ Order quantity needs to be multiple of the minimum quantity.
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
14/18
TSZ02201-0F2F0A200240-1-2
18.Apr.2017.Rev.003
Datasheet
BM2P016T
●Marking Diagram
TO220-7M
B MS 2 P 0 1 6 T
Y WW
Y：
W：
K：
L：
K L L
The last digit of the year (2014→4、2015→5)
Input week number (01-53)
Fixed character
Running Code00-99 (Reset every week)
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
15/18
TSZ02201-0F2F0A200240-1-2
18.Apr.2017.Rev.003
Datasheet
BM2P016T
Operational Notes
1.
Reverse Connection of Power Supply
Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when
connecting the power supply, such as mounting an external diode between the power supply and the IC’s power
supply pins.
2.
Power Supply Lines
Design the PCB layout pattern to provide low impedance supply lines. Separate the ground and supply lines of the
digital and analog blocks to prevent noise in the ground and supply lines of the digital block from affecting the analog
block. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and
aging on the capacitance value when using electrolytic capacitors.
3.
Ground Voltage
Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition.
4.
Ground Wiring Pattern
When using both small-signal and large-current ground traces, the two ground traces should be routed separately but
connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal
ground caused by large currents. Also ensure that the ground traces of external components do not cause variations
on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance.
5.
Thermal Consideration
Should by any chance the maximum junction temperature rating be exceeded the rise in temperature of the chip may
result in deterioration of the properties of the chip. In case of exceeding this absolute maximum rating, increase the
board size and copper area to prevent exceeding the maximum junction temperature rating.
6.
Recommended Operating Conditions
These conditions represent a range within which the expected characteristics of the IC can be approximately obtained.
The electrical characteristics are guaranteed under the conditions of each parameter.
7.
Inrush Current
When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush current may
flow instantaneously due to the internal powering sequence and delays, especially if the IC has more than one power
supply. Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and
routing of connections.
8.
Operation Under Strong Electromagnetic Field
Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction.
9.
Testing on Application Boards
When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may
subject the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply
should always be turned off completely before connecting or removing it from the test setup during the inspection
process. To prevent damage from static discharge, ground the IC during assembly and use similar precautions during
transport and storage.
10.
Inter-pin Short and Mounting Errors
Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in
damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin.
Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and
unintentional solder bridge deposited in between pins during assembly to name a few.
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
16/18
TSZ02201-0F2F0A200240-1-2
18.Apr.2017.Rev.003
Datasheet
BM2P016T
Operational Notes – continued
11.
Unused Input Pins
Input pins of an IC are often connected to the gate of a MOS transistor. The gate has extremely high impedance and
extremely low capacitance. If left unconnected, the electric field from the outside can easily charge it. The small
charge acquired in this way is enough to produce a significant effect on the conduction through the transistor and
cause unexpected operation of the IC. So unless otherwise specified, unused input pins should be connected to the
power supply or ground line.
12.
Regarding the Input Pin of the IC
This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them
isolated. P-N junctions are formed at the intersection of the P layers with the N layers of other elements, creating a
parasitic diode or transistor. For example (refer to figure below):
When GND > Pin A and GND > Pin B, the P-N junction operates as a parasitic diode.
When GND > Pin B, the P-N junction operates as a parasitic transistor.
Parasitic diodes inevitably occur in the structure of the IC. The operation of parasitic diodes can result in mutual
interference among circuits, operational faults, or physical damage. Therefore, conditions that cause these diodes to
operate, such as applying a voltage lower than the GND voltage to an input pin (and thus to the P substrate) should
be avoided.
Figure. Example of monolithic IC structure
13.
Ceramic Capacitor
When using a ceramic capacitor, determine the dielectric constant considering the change of capacitance with
temperature and the decrease in nominal capacitance due to DC bias and others.
14.
15.
Area of Safe Operation (ASO)
Operate the IC such that the output voltage, output current, and power dissipation are all within the Area of Safe
Operation (ASO).
Thermal Shutdown Circuit(TSD)
This IC has a built-in thermal shutdown circuit that prevents heat damage to the IC. Normal operation
should always be within the IC’s maximum junction temperature rating. If however the rating is
exceeded for a continued period, the junction temperature (Tj) will rise which will activate the TSD
circuit that will turn OFF all output pins. When the Tj falls below the TSD threshold, the circuits are
automatically restored to normal operation.
Note that the TSD circuit operates in a situation that exceeds the absolute maximum ratings and
therefore, under no circumstances, should the TSD circuit be used in a set design or for any purpose
other than protecting the IC from heat damage.
16.
Over Current Protection Circuit (OCP)
This IC incorporates an integrated over current protection circuit that is activated when the load is shorted. This
protection circuit is effective in preventing damage due to sudden and unexpected incidents. However, the IC should
not be used in applications characterized by continuous operation or transitioning of the protection circuit.
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
17/18
TSZ02201-0F2F0A200240-1-2
18.Apr.2017.Rev.003
Datasheet
BM2P016T
Date
Rev. No.
2016.11.1
001
New Release
Revision Point
2017.4.7
002
Change the diagram on P14
2017.4.18
003
Change the diagram on P14
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
18/18
TSZ02201-0F2F0A200240-1-2
18.Apr.2017.Rev.003
Notice
Precaution on using ROHM Products
1.
Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment,
OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you
(Note 1)
intend to use our Products in devices requiring extremely high reliability (such as medical equipment
, transport
equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car
accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or
serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.
Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any
damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific
Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU
CHINA
CLASSⅢ
CLASSⅡb
CLASSⅢ
CLASSⅢ
CLASSⅣ
CLASSⅢ
2.
ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3.
Our Products are designed and manufactured for use under standard conditions and not under any special or
extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any
special or extraordinary environments or conditions. If you intend to use our Products under any special or
extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of
product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4.
The Products are not subject to radiation-proof design.
5.
Please verify and confirm characteristics of the final or mounted products in using the Products.
6.
In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7.
De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in
the range that does not exceed the maximum junction temperature.
8.
Confirm that operation temperature is within the specified range described in the product specification.
9.
ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1.
When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2.
In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice-PGA-E
© 2015 ROHM Co., Ltd. All rights reserved.
Rev.003
Precautions Regarding Application Examples and External Circuits
1.
If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2.
You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1.
Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2.
Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3.
Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4.
Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign
trade act, please consult with ROHM in case of export.
Precaution Regarding Intellectual Property Rights
1.
All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data.
2.
ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the
Products with other articles such as components, circuits, systems or external equipment (including software).
3.
No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM
will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to
manufacture or sell products containing the Products, subject to the terms and conditions herein.
Other Precaution
1.
This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2.
The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3.
In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4.
The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice-PGA-E
© 2015 ROHM Co., Ltd. All rights reserved.
Rev.003
Datasheet
General Precaution
1. Before you use our Products, you are requested to carefully read this document and fully understand its contents.
ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of any
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this document is current as of the issuing date and subject to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sales
representative.
3.
The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or
liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccuracy or errors of or
concerning such information.
Notice – WE
© 2015 ROHM Co., Ltd. All rights reserved.
Rev.001
工商网监
湘ICP备2023018690号
