BU25TA2WHFV-TR

CMOS LDO Regulator Series for Portable Equipments High-speed Load Response FULL CMOS LDO Regulators BUTA2WNVX Series, BUTA2WHFV Series No.09020EAT01 ●Description BU□□TA2WNVX /HFV series is high-performance FULL CMOS regulator with 200-mA output, which is mounted on microminiature package SSON004X1216 (1.2 mm  1.6 mm  0.6 mm) &HVSOF5(1.6mm X 1.6mm X0.6mm). It has excellent noise characteristics and load responsiveness characteristics despite its low circuit current consumption of 40 A. It is most appropriate for various applications such as power supplies for logic IC, RF, and camera modules. Microminiature package SSON004X1216 & HVSOF5 with built-in heatsink is adopted for the package, which contributes to the space-saving design of the set. ●Features 1) High-accuracy output voltage of 1% (25 mV on 1.5-V & 1.8-V products） 2) High ripple rejection: 70 dB (Typ., 1 kHz, VOUT1.8 V)) 3) Compatible with small ceramic capacitor (CIN=Co=1.0 F) 4) Low current consumption: 40 A 5) ON/OFF control of output voltage 6) With built-in overcurrent protection circuit and overheat protection circuit 7) With built-in output discharge circuit 8) Adopting microminiature power package SSON004X1216 ●Applications Battery-powered portable equipment, etc.  Absolute maximum rating Parameter Maximum applied power voltage Power dissipation Maximum junction temperature Operational temperature range Storage temperature range Symbol VMAX Pd1 Pd2 TjMAX Topr Tstg Limits -0.3 ~ +6.5 220*1 (SSON004X1216) 410*2 (HVSOF5) +125 -40 ~ +85 -55 ~ +125 Unit V mW mW °C °C °C *1 When 1 PCB (70 mm  70 mm, thickness 1.6-mm glass epoxy) a standard ROHM board is implemented. Reduced to 2.2 mW/C when used at Ta=25C or higher. *2 When 1 PCB (70 mm  70 mm, thickness 1.6-mm glass epoxy) a standard ROHM board is implemented. Reduced to 4.1 mW/C when used at Ta=25C or higher.  Recommended operating range (Do not exceed Pd.） Parameter Symbol Limits Input power supply voltage VIN 2.5 ~ 5.5 Maximum output current IMAX 200  Recommended operating conditions Parameter Symbol Min. Typ. Max. Input capacitor CIN 0.5*3 1.0 － Output capacitor CO 0.5*3 1.0 － *3 Set the capacity value of the capacitor so that it does not fall below DC device characteristics, and change with time into consideration. Unit V mA Unit Conditions μF A ceramic capacitor is recommended. μF A ceramic capacitor is recommended. the minimum value, taking temperature characteristics, www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 1/27 2009.05 - Rev.B BUTA2WNVX Series, BUTA2WHFV Series  Block diagram, recommended circuit diagram, and pin configuration diagram BH□□TA2WNVX Technical Note VIN VIN 4/3 Cin 2 VREF OCP VOUT 1 1/4 VOUT Co GND VSTBY STBY STBY 3/1 Discharge Fig.1 Recommended circuit diagram Recommended ceramic capacitor for Cin & Co Murata Manufacturing Co., Ltd. GRM188B11A105KA61D BU□□TA2WNVX(SSON004X1216) 4 3 PIN No. 1 2 3 1 2 Symbol VOUT GND STBY VIN Function Voltage output Grounding ON/OFF control of output voltage (High: ON, Low: OFF) 4 Power input BU□□TA2WHFV(HVSOF5) PIN No. 5 4 Symbol STBY G ND V IN VOUT N.C. Function ON/OFF control of output voltage (High:ON, Low:OFF) Grounding Power input Voltage output No Connect 1 2 3 4 1 2 3 5 www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 2/27 2009.05 - Rev.B BUTA2WNVX Series, BUTA2WHFV Series Technical Note ●Electrical characteristics(Ta=25C, VIN=VOUT+1.0 V (VIN=3.5 V on VOUT=1.8-V and1.5-V products), STBY=1.5 V, CIN=1.0 F, CO=1.0 F, unless otherwise specified) Parameter Output voltage Circuit current Circuit current (at STBY) Symbol VOUT Min. VOUT×0.99 VOUT-25 mV Typ. VOUT Max. VOUT×1.01 VOUT+25 mV Unit Conditions V IOUT=10 μA，VOUT≥2.5 V IOUT=10 μA，VOUT