BU7244YFV-CE2

Datasheet Input/Output Rail-to-Rail Low Supply Current CMOS Operational Amplifier for Automotive BU7244YFV-C Key Specifications General Description  Operating Supply Voltage Range Single Supply: 1.8 V to 5.5 V Dual Supply: ±0.90 V to ±2.75 V  Operating Temperature Range: -40 °C to +125 °C  Supply Current: 360 µA (Typ)  Input Offset Current: 1 pA (Typ)  Input Bias Current: 1 pA (Typ) BU7244YFV-C is an input/output rail-to-rail CMOS operational amplifier that operates on a wide temperature range and low supply current. It is suitable for a sensor amplifier and battery-powered equipment which require low input bias current. Features       AEC-Q100 Qualified(Note 1) Input/Output Rail-to-Rail Low Operating Supply Voltage Low Supply Current Low Input Bias Current Wide Operating Temperature Range Special Characteristic  Input Offset Voltage -40 °C to +125 °C: Package SSOP-B14 (Note 1) Grade 1 12 mV (Max) W(Typ) x D(Typ) x H(Max) 5.00 mm x 6.40 mm x 1.35 mm Applications  Sensor Amplifiers  Battery-powered Equipment  Automotive Electronics Pin Description Pin Configuration Pin No. Pin Name 1 OUT1 2 IN1- Inverting input 1 13 IN4- 3 IN1+ Non-inverting input 1 IN1+ 3 12 IN4+ 4 VDD Positive power supply 11 VSS 5 IN2+ Non-inverting input 2 VDD 4 6 IN2- Inverting input 2 IN2+ 5 10 IN3+ 7 OUT2 Output 2 9 IN3- 8 OUT3 Output 3 8 OUT3 9 IN3- Inverting input 3 10 IN3+ Non-inverting input 3 11 VSS Negative power supply/Ground 12 IN4+ Non-inverting input 4 13 IN4- Inverting input 4 14 OUT4 (TOP VIEW) (TOP VIEW) 14 OUT4 OUT1 1 IN1- 2 IN2- 6 OUT2 7 CH1 - + + - + CH2 CH4 + - + CH3 〇Product structure : Silicon integrated circuit .www.rohm.com © 2017 ROHM Co., Ltd. All rights reserved. TSZ22111 • 14 • 001 Function Output 1 Output 4 〇This product has no designed protection against radioactive rays 1/21 TSZ02201-0GLG2G500820-1-2 06.Aug.2019 Rev.002 BU7244YFV-C Block Diagram VDD VBIAS IN+ Class AB control OUT IN- VBIAS VSS Figure 1. Block Diagram Absolute Maximum Ratings (Ta=25 °C) Symbol Rating Unit VDD-VSS 7 V Power Dissipation Pd 0.87(Note 2,3) W Differential Input Voltage(Note 4) VID VDD - VSS V Common-mode Input Voltage Range VICM (VSS - 0.3) to (VDD + 0.3) V II ±10 mA Tstg -55 to +150 °C Tjmax 150 °C Parameter Supply Voltage Input Current Storage Temperature Range Maximum Junction Temperature Caution 1: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated over the absolute maximum ratings. Caution 2: Should by any chance the maximum junction temperature rating be exceeded the rise in temperature of the chip may result in deterioration of the properties of the chip. In case of exceeding this absolute maximum rating, design a PCB with power dissipation taken into consideration by increasing board size and copper area so as not to exceed the maximum junction temperature rating. (Note 2) To use at temperature above Ta=25 C reduce 7.0 mW/°C. (Note 3) Mounted on an FR4 glass epoxy PCB 70 mm×70 mm×1.6 mm (Copper foil area less than 3 %). (Note 4) The differential input voltage indicates the voltage difference between inverting input and non-inverting input. The input pin voltage is set to more than VSS. Recommended Operating Conditions Parameter Symbol Min Typ Max Unit Operating Supply Voltage Vopr 1.8 ±0.90 3.0 ±1.5 5.5 ±2.75 V Operating Temperature Topr -40 +25 +125 °C www.rohm.com © 2017 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 2/21 TSZ02201-0GLG2G500820-1-2 06.Aug.2019 Rev.002 BU7244YFV-C Electrical Characteristics (Unless otherwise specified VDD=3 V, VSS=0 V, Ta=25 °C) Parameter Input Offset Voltage(Note 5,6) Symbol Limit Temperature Range Unit Min Typ Max 25 °C - 1 10 Full range - - 12 25 °C - 1 25 °C - Full range VIO Conditions mV VDD=1.8 V to 5.5 V - pA - 1 300 pA - - - 6000 pA - 25 °C - 360 750 μA Full range - - 1200 RL=∞, AV=0 dB, VIN+=1.5 V 25 °C VDD-0.05 - V RL=10 kΩ Full range VDD-0.10 - - 25 °C - - VSS+0.05 V RL=10 kΩ Full range - - VSS+0.10 25 °C 70 100 dB RL=10 kΩ Full range 65 - - VICM 25 °C 0 - 3 V - Common-mode Rejection Ratio CMRR 25 °C 45 70 - dB - Power Supply Rejection Ratio PSRR 25 °C 60 80 - dB - 25 °C 4 10 - Output Source Current(Note 6,7) ISOURCE mA VOUT=VDD-0.4 V Full range 2 - - 25 °C 5 15 mA VOUT=VSS+0.4 V Full range 3 - - SR 25 °C - 0.4 - V/μs CL=25 pF GBW 25 °C - 1 - MHz CL=25 pF, AV=40 dB θ 25 °C - 50 - deg THD+N 25 °C - 0.05 - % CS 25 °C - 100 - dB Input Offset Current(Note 5) IIO Input Bias Current(Note 5,6) IB Supply Current(Note 6) Maximum Output Voltage (High)(Note 6) Maximum Output Voltage (Low)(Note 6) Large Signal Voltage Gain(Note 6) Common-mode Input Voltage Range Output Sink Current(Note 6,7) Slew Rate Gain Bandwidth Product Phase Margin Total Harmonic Distortion + Noise Channel Separation IDD VOH VOL AV ISINK CL=25 pF, AV=40 dB VOUT=0.8 VP-P, f=1 kHz AV=40 dB, VOUT=1 Vrms (Note 5) Absolute value (Note 6) Full range: Ta=-40 °C to +125 °C (Note 7) Consider the power dissipation of the IC under high temperature environment when selecting the output current value. When the output pins are short-circuited continuously, the output current may decrease due to the temperature rise by the heat generation of inside the IC. www.rohm.com © 2017 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 3/21 TSZ02201-0GLG2G500820-1-2 06.Aug.2019 Rev.002 BU7244YFV-C Description of Terms in Electrical Characteristics Described below are descriptions of the relevant electrical terms used in this datasheet. Items and symbols generally used are also shown. Note that item names and symbols, and their meanings may differ from those on another manufacturer’s or general documents. 1. Absolute Maximum Ratings Absolute maximum rating items indicates the condition which must not be exceeded even if it is instantaneous. Applying of a voltage exceeding the absolute maximum ratings or use outside the temperature range which is provided in the absolute maximum ratings cause characteristic deterioration or destruction of the IC. 1.1 Supply Voltage (VDD/VSS) This indicates the maximum voltage that can be applied between the positive power supply pin and the negative power supply pin without deteriorating the characteristics of internal circuit or without destroying it. 1.2 Differential Input Voltage (VID) This indicates the maximum voltage that can be applied between the non-inverting input pin and the inverting input pin without deteriorating the characteristics of the IC or without destroying it. 1.3 Common-mode Input Voltage Range (VICM) This indicates the maximum voltage that can be applied to the non-inverting input pin and inverting input pin without deteriorating the characteristics of the IC or without destroying it. Common-mode Input Voltage Range of the maximum ratings does not assure normal operation of IC. For normal operation, use the IC within the Common-mode Input Voltage Range characteristics. 1.4 Power Dissipation (Pd) This indicates the power that can be consumed by the IC when mounted on a specific board at the ambient temperature 25 °C (normal temperature). As for package product, Pd is determined by the temperature that can be permitted by the IC in the package (maximum junction temperature) and the thermal resistance of the package. 2. Electrical Characteristics 2.1 Input Offset Voltage (VIO) This indicates the voltage difference between non-inverting and inverting pins. It can be translated as the input voltage difference required for setting the output voltage at 0 V. 2.2 Input Offset Current (IIO) This indicates the difference of input bias current between the non-inverting and inverting pins. 2.3 Input Bias Current (IB) This indicates the current that flows into or out from the input pin. It is defined by the average of input bias currents at the non-inverting and inverting pins. 2.4 Supply Current (IDD) This indicates the current of the IC itself flowing under the specified conditions and under no-load or steady-state conditions. 2.5 Maximum Output Voltage (High) / Maximum Output Voltage (Low) (VOH/VOL) This indicates the voltage range of the output under specified load condition. It is typically divided into maximum output voltage High and low. Maximum output voltage high indicates the upper limit of output voltage. Maximum output voltage low indicates the lower limit. 2.6 Large Signal Voltage Gain (AV) This indicates the amplifying rate (gain) of output voltage against the voltage difference between non-inverting pin and inverting pin. It is normally the amplifying rate (gain) with reference to DC voltage. AV = (Output voltage) / (Differential input voltage) 2.7 Common-mode Input Voltage Range (VICM) This indicates the input voltage range where IC normally operates. 2.8 Common-mode Rejection Ratio (CMRR) This indicates the ratio of fluctuation of input offset voltage when Common-mode Input Voltage is changed. It is normally the fluctuation of DC. CMRR = (Change of Input common-mode voltage)/(Input offset fluctuation) 2.9 Power Supply Rejection Ratio (PSRR) This indicates the ratio of fluctuation of input offset voltage when supply voltage is changed. It is normally the fluctuation of DC. PSRR= (Change of power supply voltage)/(Input offset fluctuation) 2.10 Output Source Current/ Output Sink Current (ISOURCE / ISINK) The maximum current that can be output from the IC under specific output conditions. The output source current indicates the current flowing out from the IC, and the output sink current indicates the current flowing into the IC. 2.11 Slew Rate (SR) This is a parameter representing the operational speed of the operational amplifier. This indicates the rate at which the output voltage can change in the specified unit time. 2.12 Gain Band Width (GBW) This indicates the product of an arbitrary frequency and its gain in the range of the gain slope of 6 dB/octave. 2.13 Phase Margin (θ) This indicates the margin of phase from the phase delay of 180 degree at the frequency at which the gain of the operational amplifier is 1. 2.14 Total Harmonic Distortion+Noise (THD+N) This indicates the content ratio of harmonic and noise components relative to the output signal. www.rohm.com © 2017 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 4/21 TSZ02201-0GLG2G500820-1-2 06.Aug.2019 Rev.002 BU7244YFV-C Typical Performance Curves 1.2 1000 +125 °C Supply Current [μA] Power Dissipation [W] 800 0.9 0.6 600 +25 °C 400 -40 °C 0.3 200 0.0 0 0 25 50 75 100 125 150 1 3 4 5 Ambient Temperature [°C] Supply Voltage [V] Figure 2. Power Dissipation vs Ambient Temperature (Derating Curve) Figure 3. Supply Current vs Supply Voltage 6 6 Maximum Output Voltage (High) [V] 1000 800 5.5 V Supply Current [μA] 2 600 3.0 V 400 1.8 V 200 +125 °C 5 +25 °C 4 -40 °C 3 2 1 0 0 -50 -25 0 25 50 75 100 125 1 2 3 4 5 Ambient Temperature [°C] Supply Voltage [V] Figure 4. Supply Current vs Ambient Temperature Figure 5. Maximum Output Voltage (High) vs Supply Voltage (RL=10 kΩ) 6 (Note) The above characteristics are measurements of typical sample, they are not guaranteed. www.rohm.com © 2017 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 5/21 TSZ02201-0GLG2G500820-1-2 06.Aug.2019 Rev.002 BU7244YFV-C Typical Performance Curves - continued 20 5.5 V 5 Maximum Output Voltage (Low) [mV] Maximum Output Voltage (High) [V] 6 4 3.0 V 3 1.8 V 2 1 0 10 +125 °C 5 +25 °C -40 °C 0 -50 -25 0 25 50 75 100 125 1 2 3 4 5 Ambient Temperature [°C] Supply Voltage [V] Figure 6. Maximum Output Voltage (High) vs Ambient Temperature (RL=10 kΩ) Figure 7. Maximum Output Voltage (Low) vs Supply Voltage (RL=10 kΩ) 6 10 Output Source Current [mA] 20 Maximum Output Voltage (Low) [mV] 15 15 10 5.5 V 5 3.0 V -40 °C 8 +25 °C 6 +125 °C 4 2 1.8 V 0 0 -50 -25 0 25 50 75 100 0.0 125 0.3 0.6 0.9 1.2 1.5 1.8 Ambient Temperature [°C] Output Voltage [V] Figure 8. Maximum Output Voltage (Low) vs Ambient Temperature (RL=10 kΩ) Figure 9. Output Source Current vs Output Voltage (VDD=1.8 V) (Note) The above characteristics are measurements of typical sample, they are not guaranteed. www.rohm.com © 2017 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 6/21 TSZ02201-0GLG2G500820-1-2 06.Aug.2019 Rev.002 BU7244YFV-C Typical Performance Curves - continued 50 80 Output Source Current [mA] Output Source Current [mA] 70 40 +125 °C 30 20 -40 °C +25 °C +125 °C 60 50 +25 °C 40 30 -40 °C 20 10 10 0 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 0 1 2 3 4 5 6 Output Voltage [V] Output Voltage [V] Figure 10. Output Source Current vs Output Voltage (VDD=3.0 V) Figure 11. Output Source Current vs Output Voltage (VDD=5.5 V) 20 20 16 16 Output Sink Current [mA] Output Source Current [mA] -40 °C 5.5 V 12 3.0 V 8 1.8 V 4 +25 °C 12 +125 °C 8 4 0 0 -50 -25 0 25 50 75 100 125 0 0.3 0.6 0.9 1.2 1.5 1.8 Ambient Temperature [°C] Output Voltage [V] Figure 12. Output Source Current vs Ambient Temperature (VOUT=VDD-0.4 V) Figure 13. Output Sink Current vs Output Voltage (VDD=1.8 V) (Note) The above characteristics are measurements of typical sample, they are not guaranteed. www.rohm.com © 2017 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 7/21 TSZ02201-0GLG2G500820-1-2 06.Aug.2019 Rev.002 BU7244YFV-C Typical Performance Curves - continued 50 100 40 80 +125 °C 30 Output Sink Current [mA] Output Sink Current [mA] +125 °C +25 °C -40 °C 20 60 +25 °C 40 10 -40 °C 20 0 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 0 1 2 3 4 5 6 Output Voltage [V] Output Voltage [V] Figure 14. Output Sink Current vs Output Voltage (VDD=3.0 V) Figure 15. Output Sink Current vs Output Voltage (VDD=5.5 V) 40 10.0 30 20 Input Offset Voltage [mV] Output Sink Current [mA] 7.5 5.5 V 3.0 V 10 1.8 V 5.0 2.5 0.0 +25 °C +125 °C -40 °C -2.5 -5.0 -7.5 0 -10.0 -50 -25 0 25 50 75 100 125 1 2 3 4 5 6 Ambient Temperature [°C] Supply Voltage [V] Figure 16. Output Sink Current vs Ambient Temperature (VOUT=VSS+0.4 V) Figure 17. Input Offset Voltage vs Supply Voltage (VICM=VDD, EK=-VDD/2) (Note) The above characteristics are measurements of typical sample, they are not guaranteed. www.rohm.com © 2017 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 8/21 TSZ02201-0GLG2G500820-1-2 06.Aug.2019 Rev.002 BU7244YFV-C Typical Performance Curves - continued 7.5 7.5 5.0 5.0 Input Offset Voltage [mV] 10.0 Input Offset Voltage [mV] 10.0 2.5 0.0 5.5 V 3.0 V 1.8 V -2.5 -5.0 -7.5 0.0 +25 °C +125 °C -2.5 -40 °C -5.0 -7.5 -10.0 -10.0 -50 -25 0 25 50 75 100 -1 125 0 1 2 3 Ambient Temperature [°C] Input Voltage [V] Figure 18. Input Offset Voltage vs Ambient Temperature (VICM=VDD, EK=-VDD/2) Figure 19. Input Offset Voltage vs Input Voltage (VDD=1.8 V) 10.0 10.0 7.5 7.5 5.0 5.0 Input Offset Voltage [mV] Input Offset Voltage [mV] 2.5 2.5 0.0 +25 °C +125 °C -2.5 -40 °C -5.0 2.5 +125 °C +25 °C 0.0 -2.5 -40 °C -5.0 -7.5 -7.5 -10.0 -10.0 -1 0 1 2 3 -1 4 0 1 2 3 4 5 6 Input Voltage [V] Input Voltage [V] Figure 20. Input Offset Voltage vs Input Voltage (VDD=3.0 V) Figure 21. Input Offset Voltage vs Input Voltage (VDD=5.5 V) 7 (Note) The above characteristics are measurements of typical sample, they are not guaranteed. www.rohm.com © 2017 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 9/21 TSZ02201-0GLG2G500820-1-2 06.Aug.2019 Rev.002 BU7244YFV-C Typical Performance Curves - continued 160 +125 °C +25 °C Large Signal Voltage Gain [dB] Large Signal Voltage Gain [dB] 160 120 -40 °C 80 40 5.5 V 120 80 40 0 0 1 2 3 4 5 -50 6 -25 Supply Voltage [V] 0 25 50 75 100 125 Ambient Temperature [°C] Figure 22. Large Signal Voltage Gain vs Supply Voltage Figure 23. Large Signal Voltage Gain vs Ambient Temperature 120 120 Common-mode Rejection Ratio [dB] Common-mode Rejection Ratio [dB] 1.8 V 3.0 V 100 +25 °C 80 60 +125 °C -40 °C 40 20 100 5.5 V 80 60 3.0 V 1.8 V 40 20 0 0 1 2 3 4 5 -50 6 Supply Voltage [V] -25 0 25 50 75 100 125 Ambient Temperature [°C] Figure 24. Common-mode Rejection Ratio vs Supply Voltage Figure 25. Common-mode Rejection Ratio vs Ambient Temperature (Note) The above characteristics are measurements of typical sample, they are not guaranteed. www.rohm.com © 2017 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 10/21 TSZ02201-0GLG2G500820-1-2 06.Aug.2019 Rev.002 BU7244YFV-C Typical Performance Curves - continued 2.0 120 Slew Rate L-H [V/μs] Power Supply Rejection Ratio [dB] 140 100 80 60 40 1.5 5.5 V 1.0 3.0 V 1.8 V 0.5 20 0 0.0 -50 -25 0 25 50 75 100 125 -50 -25 0 25 50 75 100 125 Ambient Temperature [°C] Ambient Temperature [°C] Figure 26. Power Supply Rejection Ratio vs Ambient Temperature Figure 27. Slew Rate(L-H) vs Ambient Temperature 2.0 100 200 Phase 80 160 60 120 1.0 5.5 V 0.5 40 Gain 80 20 0.0 -25 0 25 40 3.0 V 1.8 V -50 Phase [deg] Voltage Gain [dB] Slew Rate H-L [V/μs] 1.5 50 75 100 125 0 1.E+02 102 Ambient Temperature [°C] 1.E+03 103 1.E+04 1.E+05 104 105 Frequency [Hz] 1.E+06 106 0 1.E+07 107 Figure 29. Voltage Gain/Phase vs Frequency (VDD=3.0 V) Figure 28. Slew Rate(H-L) vs Ambient Temperature (Note) The above characteristics are measurements of typical sample, they are not guaranteed. www.rohm.com © 2017 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 11/21 TSZ02201-0GLG2G500820-1-2 06.Aug.2019 Rev.002 BU7244YFV-C Application Information NULL method condition for Test Circuit 1 VDD, VSS, EK, VICM, VRL, Unit: V Parameter VF Input Offset Voltage SW1 SW2 SW3 VF1 VDD VSS EK VICM -1.5 3 - 1 1.5 1.5 2 - 3 - 4 ON ON OFF 3 0 ON ON ON 3 0 VF2 -0.5 Large Signal Voltage Gain VF3 -2.5 VF4 Common-mode Rejection Ratio (Common-mode Input Voltage Range) VRL Calculation 0 ON ON OFF 3 0 -1.5 VF5 3 VF6 1.8 Power Supply Rejection Ratio ON ON OFF VF7 -0.90 0 5.5 0 -2.75 - Calculation |VF1| 1+RF/RS 1. Input Offset Voltage (VIO) VIO = 2. Large Signal Voltage Gain (AV) Av = 20Log ΔEK × (1+RF/RS) [dB] |VF2-VF3| [V] 3. Common-mode Rejection Ratio (CMRR) CMRR = 20Log ΔVICM × (1+RF/RS) [dB] |VF4 - VF5| 4. Power Supply Rejection Ratio (PSRR) PSRR = 20Log ΔVDD × (1+ RF/RS) [dB] |VF6 - VF7| 0.1 μF RF=50 kΩ SW1 RS=50 Ω 500 kΩ VDD +15 V EK RI=1 MΩ 0.01 μF VOUT 500 kΩ 0.015 μF 0.015 μF DUT SW3 RS=50 Ω 1000 pF RI=1 MΩ NULL RL VICM 50 kΩ SW2 V VF VRL -15 V VSS Figure 30. Test Circuit 1 www.rohm.com © 2017 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 12/21 TSZ02201-0GLG2G500820-1-2 06.Aug.2019 Rev.002 BU7244YFV-C Application Information - continued Switch Condition for Test Circuit 2 Parameter SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8 SW9 SW10 SW11 SW12 Supply Current OFF OFF ON OFF ON OFF OFF OFF OFF OFF OFF OFF Maximum Output Voltage (High/Low) OFF ON OFF OFF ON OFF OFF Output Current OFF ON OFF OFF ON OFF OFF OFF OFF Slew Rate OFF OFF Gain Bandwidth Product ON ON OFF OFF OFF OFF OFF ON ON ON ON OFF OFF ON ON OFF OFF OFF OFF ON OFF OFF ON OFF OFF OFF ON OFF OFF ON SW3 R2=100 kΩ SW4 ● VDD － SW1 SW2 ＋ SW8 SW9 SW10 SW11 SW12 SW5 SW6 SW7 R1=1 kΩ VSS RL VIN- VIN+ CL VOUT VRL Figure 31. Test Circuit 2 Output Voltage Input Voltage SR = Δ V / Δ t 3V 3V 90% ΔV 3 V P-P 10% 0V 0V t Δt Input Wave t Output Wave Figure 32. Slew Rate www.rohm.com © 2017 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 13/21 TSZ02201-0GLG2G500820-1-2 06.Aug.2019 Rev.002 BU7244YFV-C Application Information – continued 1. Unused Circuits When there are unused op-amps, it is recommended that they are connected as in Figure 33, set the non-inverting input pin to a potential within the Common-mode Input Voltage Range (VICM). VDD Potential within VICM VICM VSS Figure 33. Example of Application Circuit for Unused Op-amp 2. Input Voltage Applying VSS-0.3V to VDD+0.3V to the input pin is possible without causing deterioration of the electrical characteristics or destruction. However, this does not ensure normal circuit operation. Note that the circuit operates normally only when the input voltage is within the common mode input voltage range of the electric characteristics. 3. Power Supply (Single/Dual) The operational amplifier operates when the voltage supplied is between the VDD and VSS pin. Therefore, the single supply operational amplifiers can be used as dual supply operational amplifiers as well. 4. Latch-up Do not set the voltage of the input/output pin to VDD or more and VSS or less because there is a possibility of latch-up state peculiar to the CMOS device. Also, be careful that the abnormal noise and etc. are not added to the IC. 5. Decoupling Capacitor Insert the decoupling capacitance between VDD and VSS, for stable operation of operational amplifier. If a decoupling capacitor is not inserted, malfunction may occur due to power supply noise. 6. Start-up the Supply Voltage This IC has ESD protection diode between input pin and the VDD and VSS pin. When apply the voltage to input pin before start-up the supply voltage, then a current flows in VDD or VSS pin through this diode. The current is depending on applied voltage. This phenomena causes breakdown the IC or malfunction. Therefore, give a special consideration to input pin protection and start-up order of supply voltage. Also, after turning on the power supply, this IC outputs High level voltage regardless of the state of input up to around 1 V of the start-up voltage of the circuit. Pay attention to the sequence of turning on the power supply and the etc., because there is a possibility of the set malfunction. 7. Output Capacitor When the VDD pin is shorted to the VSS(GND) potential with the electric charge accumulated in the external capacitor connected to the output pin, the accumulated electric charge passes through the parasitic element or protective element inside the circuit and is discharged to the VDD pin, the elements inside the circuit may be damaged.(Thermal destruction) If use this IC as an application circuit which does not cause the oscillation phenomenon due to output capacitive load (e.g., a voltage comparator not constituting a negative feedback circuit), the capacitor connected to the output pin should be 0.1 µF or less in order to prevent the damage of IC due to accumulated charge of it. www.rohm.com © 2017 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 14/21 TSZ02201-0GLG2G500820-1-2 06.Aug.2019 Rev.002 BU7244YFV-C Application Information – continued 8. Oscillation by Output Capacitor When designing an application circuit which constitutes a negative feedback circuit using this IC, check sufficiently about oscillation by capacitive load. When the amplifier is used with a full feedback loop, a capacitive load must be up to 100 pF because there is a risk of oscillation. The following figures show the frequency characteristics for each load capacitance. 50 20 40 150 pF Voltage Gain [dB] Voltage Gain [dB] 10 30 20 5 pF 0 -10 150 pF 10 100 pF 100 pF 5 pF 0 -20 104 105 106 103 107 105 106 Frequency [Hz] Figure 34. Voltage Gain vs Frequency (VDD=3.0 V, GV=40 dB) Figure 35. Voltage Gain vs Frequency (VDD=3.0 V, GV=0 dB) 70 70 60 60 50 50 40 30 20 10 0 104 Frequency [Hz] Phase Margin [deg] Phase Margin [deg] 103 107 40 30 20 10 10 100 1000 Load Capacitance [pF] 10 100 1000 Load Capacitance [pF] Figure 36. Phase Margin vs Load Capacitance (VDD=3.0 V, GV=40 dB) www.rohm.com © 2017 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 0 15/21 Figure 37. Phase Margin vs Load Capacitance (VDD=3.0 V, GV=0 dB) TSZ02201-0GLG2G500820-1-2 06.Aug.2019 Rev.002 BU7244YFV-C Oscillation by Output Capacitor – continued The following figure shows an improved circuit example of the frequency characteristics due to the output capacitor. 8. Figure 38. Improvement Circuit Example 1 Figure 39. Improvement Circuit Example 2 20 20 RL=0 Ω RL=500 Ω RL=1 kΩ 0 -10 RL=0 Ω 10 Voltage Gain [dB] Voltage Gain [dB] 10 RL=500 Ω RL=1 kΩ 0 -10 -20 -20 103 104 105 106 107 Frequency [Hz] 104 105 106 107 Frequency [Hz] Figure 40. Voltage Gain vs Frequency (VDD=3.0 V, GV=0 dB, CL=100 pF, Circuit: Figure38) www.rohm.com © 2017 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 103 16/21 Figure 41. Voltage Gain vs Frequency (VDD=3.0 V, GV=0 dB, CL=100 pF, Circuit: Figure39) TSZ02201-0GLG2G500820-1-2 06.Aug.2019 Rev.002 BU7244YFV-C Examples of Circuit ○Voltage Follower Using this circuit, the output voltage (VOUT) is configured to be equal to the input voltage (VIN). This circuit also stabilizes the output voltage (VOUT) due to high input impedance and low output impedance. Computation for output voltage (VOUT) is shown below. VDD OUT VOUT=VIN IN VSS Figure 42. Voltage Follower Circuit ○Inverting Amplifier R2 For inverting amplifier, input voltage (VIN) is amplified by a voltage gain and depends on the ratio of R1 and R2. The out-of-phase output voltage is shown in the next expression VDD R1 IN OUT VOUT=-(R2/R1)VIN This circuit has input impedance equal to R1. VSS Figure 43. Inverting Amplifier Circuit ○Non-inverting Amplifier R1 R2 For non-inverting amplifier, input voltage (VIN) is amplified by a voltage gain, which depends on the ratio of R1 and R2. The output voltage (VOUT) is in-phase with the input voltage (VIN) and is shown in the next expression. VDD OUT VOUT=(1 + R2/R1)VIN IN Effectively, this circuit has high input impedance since its input side is the same as that of the operational amplifier. VSS Figure 44. Non-inverting Amplifier Circuit www.rohm.com © 2017 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 17/21 TSZ02201-0GLG2G500820-1-2 06.Aug.2019 Rev.002 BU7244YFV-C Operational Notes 1. Reverse Connection of Power Supply Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when connecting the power supply, such as mounting an external diode between the power supply and the IC’s power supply pins. 2. Power Supply Lines Design the PCB layout pattern to provide low impedance supply lines. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and aging on the capacitance value when using electrolytic capacitors. 3. Ground Voltage Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition. 4. Ground Wiring Pattern When using both small-signal and large-current ground traces, the two ground traces should be routed separately but connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal ground caused by large currents. Also ensure that the ground traces of external components do not cause variations on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance. 5. Recommended Operating Conditions The function and operation of the IC are guaranteed within the range specified by the recommended operating conditions. The characteristic values are guaranteed only under the conditions of each item specified by the electrical characteristics. 6. Inrush Current When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush current may flow instantaneously due to the internal powering sequence and delays, especially if the IC has more than one power supply. Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and routing of connections. 7. Testing on Application Boards When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may subject the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply should always be turned off completely before connecting or removing it from the test setup during the inspection process. To prevent damage from static discharge, ground the IC during assembly and use similar precautions during transport and storage. 8. Inter-pin Short and Mounting Errors Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin. Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and unintentional solder bridge deposited in between pins during assembly to name a few. 9. Unused Input Pins Input pins of an IC are often connected to the gate of a MOS transistor. The gate has extremely high impedance and extremely low capacitance. If left unconnected, the electric field from the outside can easily charge it. The small charge acquired in this way is enough to produce a significant effect on the conduction through the transistor and cause unexpected operation of the IC. So unless otherwise specified, unused input pins should be connected to the power supply or ground line. 10. Regarding the Input Pin of the IC In the construction of this IC, P-N junctions are inevitably formed creating parasitic diodes or transistors. The operation of these parasitic elements can result in mutual interference among circuits, operational faults, or physical damage. Therefore, conditions which cause these parasitic elements to operate, such as applying a voltage to an input pin lower than the ground voltage should be avoided. Furthermore, do not apply a voltage to the input pins when no power supply voltage is applied to the IC. Even if the power supply voltage is applied, make sure that the input pins have voltages within the values specified in the electrical characteristics of this IC. 11. Ceramic Capacitor When using a ceramic capacitor, determine a capacitance value considering the change of capacitance with temperature and the decrease in nominal capacitance due to DC bias and others. www.rohm.com © 2017 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 18/21 TSZ02201-0GLG2G500820-1-2 06.Aug.2019 Rev.002 BU7244YFV-C Physical Dimension and Packing Information Package Name www.rohm.com © 2017 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 SSOP-B14 19/21 TSZ02201-0GLG2G500820-1-2 06.Aug.2019 Rev.002 BU7244YFV-C Ordering Information B U 7 2 4 4 Y F V Package Part Number BU7244YFV FV:SSOP-B14 - C E 2 Product Rank C: for Automotive Packaging and forming specification E2: Embossed Tape and Reel Marking Diagram SSOP-B14(TOP VIEW) Part Number Marking 7244C LOT Number Pin 1 Mark www.rohm.com © 2017 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 20/21 TSZ02201-0GLG2G500820-1-2 06.Aug.2019 Rev.002 BU7244YFV-C Revision History Date Revision 27.Dec.2017 001 New Release 06.Aug.2019 002 Fix Pin Configuration. www.rohm.com © 2017 ROHM Co., Ltd. All rights reserved. TSZ22111 • 15 • 001 Changes 21/21 TSZ02201-0GLG2G500820-1-2 06.Aug.2019 Rev.002 Notice Precaution on using ROHM Products 1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅢ CLASSⅣ CLASSⅢ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (Exclude cases where no-clean type fluxes is used. However, recommend sufficiently about the residue.); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse, is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in the range that does not exceed the maximum junction temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice-PAA-E © 2015 ROHM Co., Ltd. All rights reserved. Rev.004 Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl 2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign trade act, please consult with ROHM in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the Products with other articles such as components, circuits, systems or external equipment (including software). 3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the Products, subject to the terms and conditions herein. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice-PAA-E © 2015 ROHM Co., Ltd. All rights reserved. Rev.004 Datasheet General Precaution 1. Before you use our Products, you are requested to carefully read this document and fully understand its contents. ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of any ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this document is current as of the issuing date and subject to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sales representative. 3. The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccuracy or errors of or concerning such information. Notice – WE © 2015 ROHM Co., Ltd. All rights reserved. Rev.001