IA1208-FB11A

IA1208-FB11A Contact image sensor heads Color image sensor heads for multi-function IA1208-FB11A Flatbed type Color Image Sensor Head, utilizing RGB light source uniquely developed by ROHM. It utilizes sensor IC with resolution change function, enabling the selection of optical resolution according to the scanning media. Applications Image sensor heads are designed for multi-function equipment such as facsimiles with color scanner or multiple function printers. Features 1) Signal amplifier is built into the image sensor IC in order to increase immunity to external noise. 2) Employing low voltage driving sensor enables 3.3V drive which is identical to the ASIC. 3) The LED light source is mounted on the same substrate as the sensor chip which allows packaging of the device with lighter weight and smaller size. 4) With the proprietary prism, the output signal is maintained uniformly. 5) The ceramic substrate is used for excellent dimensional accuracy and thermal stability. External dimensions (Unit : mm) 2-φ1.5×2 Oval Hole D4MIN 2±0.2 2±0.2 Scanning Line 1.5 Effective 1st bit 14±0.2 14±0.2 2±0.2 236±0.5 (232) 216 5 2+0.1 −0.3 12.4±0.5 9.4 0.724±0.1 17.5 4.72 6.496 7.22 16.5±0.5 2-φ1.5 D4MIN 3.5±0.2 0.724±0.1 3 16 15 219.2±0.3 3.8 4.5 2φ3 +0 0.05 − 2- R0 .5 4+0.2 5-0 2-C0.3 2-C0.3 MAX.3.15 (9.8) 219.2±0.3 13.8 Pin No. No.1 No.2 No.3 No.4 No.5 No.6 Signal Ao MODE GND VDD VREF SP Pin No. No.7 No.8 No.9 No.10 No.11 No.12 Signal CLK V-LED B-GND G-GND R-GND NC 3.5±0.2 6.5 4+0.2 5-0 6.5 6 1/5 IA1208-FB11A Contact image sensor heads Characteristics Parameter Effective scanning width Primary scan dot density Total dot number Power supply voltage Reference voltage Scanning speed Clock frequency Maximum dynamic range Minimum dynamic range Dark output Operating temperature Symbol − − − VDD VREF SLT CLK VRMax VRMin. Vod − Typ. 216 1200 10368 3.3 0.8 9.0 5 0.75 0.375 VREF + 0.1 − 5 to 45 Unit mm dpi dots V V ms / line MHz V V V °C Pin assignments No. 1 2 3 4 5 6 7 8 9 10 11 12 Circuit NC R-GND G-GND B-GND V-LED SP VDD CLK GND VREF MODE AO I/O − I I I I I I I I I I O Function − RED LED ground GREEN LED ground BLUE LED ground LED power supply Start pulse Power supply Clock Ground Reference voltage Mode select Analog output 2/5 IA1208-FB11A Contact image sensor heads Timing chart (a) CLK Timing Chart 1/fCLK twH twL CLK 50% 50% SP tSETUP tHOLD ts Ao 1pixel 2pixel (b-1) Data Output Timing Chart (1200dpi mode) After turning on the SP pulse, the analog output starts from the setting up point of 82 clock pulse. 1 2 82 83 84 109 110 111 CLK SP Ao VREF Output Period(82pixels) 1 to 82pixels Vdummy 83 to 190pixels Analog Output Period 191 to 10450pixels Note) The CLK section area which is over the effective pixcel numbers (Output blank part) cannot be used as the analog Output standard level. 3/5 IA1208-FB11A Contact image sensor heads (b-2)Data Output Timing Chart (600dpi mode) After turning on the SP pulse, the analog output starts from the setting up point of 82 clock pulse. 1 2 82 83 84 109 110 111 C LK SP Ao VREF Output Period(82pixels) 1 to 82pixels Vdummy 83 to 136pixels Analog Output Period 137 to 5266pixels Note) The CLK section area which is over the effective pixcel numbers (Output blank part) cannot be used as the analog Output standard level. (b-3)Data Output Timing Chart (300dpi mode) After turning on the SP pulse, the analog output starts from the setting up point of 82 clock pulse. 1 2 82 83 84 109 110 111 CLK SP Ao VREF output period Vdummy Analog output period 1 to 82pixels 83 to 109pixels 110 to 2674pixels Note)The CLK section area which is over the effective pixel numbers (Output blank part) cannot be used as the analog Output standard level. 4/5 IA1208-FB11A Contact image sensor heads Circuit diagram VDD 1µF×3 1 10368 GND SP ANALOG MEMORY CIRCUIT CLK VDD VREF AO VREF VLED RGND GGND BGND Peripheral circuit IMAGE SENSOR UNIT 12 9 10 11 8 1 5 4 6 7 3 2 C5 R3 R2 B G R A C1 R1 C3 NC VDD C2 SP CLK GND LED GND C4 VLED VREF GND R1=R2=100Ω, R3=100KΩ C1=C2=47µF C3=100µF, C4=0.1µF, C5=100pF 5/5 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1