KD2003-DF11A

KD2003-DF11A Printheads Compact medium speed thick film thermal printhead (8 dots / mm) KD2003-DF11A KD2003-DF11A built in new and high density driver IC developed by the cutting edge technologies realizes the highest speed in the same class (250mm/s) at both Thermal Transfer and Direct Thermal. This Thermal Printhead is suitable for POS, ATM, KIOSK and TICKET industries which require High Speed / High Density and Graphic printing. By the implementation of highly durable protective coat, it achieves 150km as the standard abrasion life. Applications POS printers ATM printers KIOSK printers Ticket printers Features 1) The use of a special partial glaze and the latest heating element structure, along with new high-density driver chips that can accept big current, has allowed ROHM to achieve print speeds of 250mm/s with using thermal history control, the fastest in its class ( with historical control ). 2) One rank resistance value of 650Ω ± 3% eliminates the inconvenience of rank selection. 3) The required driving voltage of 3.15 to 5.25V allows wide range of power supply voltage setting. This also allows multiple choice of electronic components for printers. 4) With the standard abrasion life of 150km, long life is achieved against the largely abrasive thermal paper. Dimensions (Unit : mm) 91 80 (EFFECTIVE PRINT WITH) DOT #640 MAX. 20 5.1±0.4 4±0.2 DOT #1 2.6±0.1 No.15 CONNECTOR B 10.2±0.2 No.1 No.15 CONNECTOR A 5±0.2 81±0.2 2-M3 EFFECTIVE DEPTH 3 5.1±0.2 φ2 0.0 No.1 1/4 KD2003-DF11A Printheads Equivalent circuit VH GND 13,14,15 1,2,3,4, 5 DOT #640 DOT #1 1,2,3,4 12,13,14,15 VH GND VSF 12 L/S 5 4 3 2 1 9 STB1 STB5 9 10 STB2 STB4 8 11 STB3 LATCH REGISTER DI 11 SHIFT REGISTER NC TM TM 10 6 7 THERMISTOR 30kΩ B3950 6 5 7 8 LAT DO CLK VDD CONNECTOR B CONNECTOR A Fig.1 Pin assignments CONNECTOR A No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Circuit VH VH VH VH DO LAT CLK VDD STB1 STB2 STB3 GND GND GND GND CONNECTOR B No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Circuit GND GND GND GND GND TM TM STB4 STB5 N.C. DI VSF VH VH VH 2/4 KD2003-DF11A Printheads Timing chart tw CLK CLOCK (CLK) t setup DI DATA IN (DI) “High”:BLACK “Low” :WHITE DATA OUT (DO) “High”:BLACK “Low” :WHITE t setup LAT LATCH (LAT) “High”:HOLD “Low” :THROUGH tw LAT STROBE (STB) t setup STB t hold LAT t hold DI td DO tdo DRIVER OUT tdo Fig.2 Characteristics Parameter Effective printing width Dot pitch Total dot number Average resistance value Applied voltage Applied power Print cycle Pulse width Maximum number of dots energized simultaneously Maximum clock frequency Maximum roller diameter Running life / pulse life Operating temperature Symbol − − − Rave VH PO SLT TON − − − − − Typical 80 0.125 640 650 24 0.78 0.5 0.19 384 16 φ20 150/1×10 5 to 45 8 Unit mm mm dots Ω V W/dot ms ms dots MHz mm km/pulses °C 3/4 KD2003-DF11A Printheads Electrical characteristic curves 0.8 Paper : KF50-HDA (OJI) 0.7 1.8 1.6 1.4 OPTICAL DENSITY 0.8 SLT : 1.25ms/line 0.7 0.6 0.6 ENERGY (mJ/dot) 1.2 1.0 0.8 0.6 0.4 0.2 0.5 0.4 0.3 0.2 0.1 0 0 1 2 3 4 5 ENERGY (mJ/dot) 0.5 0.4 0.3 0.2 0.1 0.0 0.00 0.05 0.10 0.15 0.20 0.25 0.30 0 0 1 2 3 4 5 SCANNING LINE TIME (ms/line) ENERGY (mJ/dot) SCANNING LINE TIME (ms/line) Fig.3 Adaptive speed chart Fig.4 Representative density curve Fig.5 Maximum energy curve 180 160 140 RESISTANCE : (kΩ) 120 100 80 60 40 20 0 −20 −10 0 10 20 30 40 50 60 70 TEMPERATURE : (°C) Fig.6 Thermistor curve 4/4 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of which would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM cannot be held responsible for any damages arising from the use of the products under conditions out of the range of the specifications or due to non-compliance with the NOTES specified in this catalog. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact your nearest sales office. ROHM Customer Support System www.rohm.com Copyright © 2008 ROHM CO.,LTD. THE AMERICAS / EUROPE / ASIA / JAPAN Contact us : webmaster@ rohm.co. jp 21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan TEL : +81-75-311-2121 FAX : +81-75-315-0172 Appendix1-Rev2.0