KF2003-GF41A

KF2003-GF41A Printheads Compact high speed thick film thermal printhead (8dots / mm) KF2003-GF41A Using its expertise in LSI technology, ROHM has developed new high density driver chips for use in the KF2003-GF41A . Capable of being employed for both thermal and thermal transfer printing, with a print speed of 200mm/s, the resulting printheads are the fastest in their class. The high-speed and high-density printing answers the needs of ATM, kiosk and ticket printing devices, which are increasingly being called upon to produce graphical output. !Applications Label printers Ticket printers POS printers ATM printers KIOSK printers Terminal printers !Features 1) The use of a special partial glaze and the latest heating element structure, along with new high-density driver chips that can accept big current, has allowed ROHM to achieve print speeds of 200mm/s, the fastest in its class. 2) One rank resistance value of 650Ω ± 3% eliminates the inconvenience of rank selection. 3) 2-inch, 3-inch and 4-inch series are available. !External dimensions (Units : mm) 91±0.3 Max.1.7 (5.1) Max.18 2.6±0.1 80 (Effective Print Width) Dot #640 Dot #1 No.28 No.1 Connector M AX .φ 20 .0 Insert Direction Exposed Conductor Side 81±0.2 5±0.2 5.1±0.1 2-M3 (Effective Depth 3) 10.2 1/4 KF2003-GF41A Printheads !Equivalent circuit VH GND 1,2,3,4 DOT #640 DOT #1 7-11,19-22 VDD 5 15 4 3 2 1 STB2 18 STB1 12 LAT CLK DI2 DO2 DI1 DO1 TM TM 14 13 24 23 6 5 16 17 LATCH REGISTER SHIFT REGISTER 2 SHIFT REGISTER 1 THERMISTOR Fig.1 !Pin assignments No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Circuit VH VH VH VH DO1 DI1 GND GND GND GND GND STB1 CLK LAT No. 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Circuit VDD TM TM STB2 GND GND GND GND DO2 DI2 VH VH VH VH 2/4 KF2003-GF41A Printheads !Timing chart tw CLK CLOCK (CLK) t setup DI DATA IN (DI) "High":BLACK "Low" :WHITE DATA OUT (DO) "High":BLACK "Low" :WHITE t hold DI td DO t setup LAT LATCH (LAT) "High":HOLD "Low" :THROUGH tw LAT STROBE (STB) t hold LAT t setup STB tdo DRIVER OUT tdo Fig.2 !Characteristics Parameter Effective printing width Dot pitch Total dot number Average resistance value Applied voltage Applied power Print cycle Pulse width Maximum number of dots energized simultaneously Maximum clock frequency Maximum roller diameter Running life / pulse life Operating temperature Symbol − − − Rave VH PO SLT TON − − − − − Typical 80 0.125 640 650 24 0.76 0.625 0.234 640 8 φ20.0 50/5×10 5~45 7 Unit mm mm dots Ω V W/dot ms ms dots MHz mm km/pulses °C 3/4 KF2003-GF41A Printheads !Electrical characteristic curves 0.8 Paper : KF50-HDA (OJI) 0.7 0.6 ENERGY (mJ/dot) OPTICAL DENSITY 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 1.8 SLT : 0.620ms/line 0.8 0.7 0.6 ENERGY (mJ/dot) 0.5 0.4 0.3 0.2 0.1 0 0 1 2 3 4 5 0.5 0.4 0.3 0.2 0.1 0.0 0.00 0.05 0.10 0.15 0.20 0.25 0.30 0 0 1 2 3 4 5 SCANNING LINE TIME (ms/line) ENERGY (mJ/dot) SCANNING LINE TIME (ms/line) Fig.3 Adaptive speed chart Fig.4 Representative density curve Fig.5 Maximum energy curve 180 160 140 RESISTANCE : (kΩ) 120 100 80 60 40 20 0 −20 −10 0 10 20 30 40 50 60 70 TEMPERATURE : (°C) Fig.6 Thermistor curve 4/4 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document use silicon as a basic material. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.0