General-purpose Operational Amplifiers /Comparators
TROPHY SERIES Comparators
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR
●Description The Universal Standard family LM393 / LM339/ LM2903 / LM2901 monolithic ICs integrate two/four independent comparators on a single chip and feature high gain, low power consumption, and an operating voltage range from 2[V] to 36[V] (single power supply).
LM393 family
LM393DR LM393PWR LM393DGKR
No.11094EBT03
TROPHY SERIES
Dual LM2903 family
LM2903DR LM2903PWR LM2903DGKR LM2903VQDR LM2903VQPWR LM339DR LM339PWR
Quad LM339 family LM2901 family
LM2901DR LM2901PWR LM2901VQDR LM2901VQPWR
●Features 1) Operating temperature range Commercial Grade LM339/393 family : 0[℃] to + 70[℃] Extended Industrial Grade LM2903/2901 family : -40[℃] to +125[℃] 2) Open collector output 3) Single / dual power supply compatible 4) Low supply current 0.8[mA] typ. (LM393/339/2903/2901 family) 5) Low input-bias current: 25[nA] typ. 6) Low input-offset voltage: 2[mV] typ. 7) Differential input voltage range equal to maximum rating 8) Low output saturation voltage 9) TTL,MOS,CMOS compatible output ●Pin Assignment
1OUT 1 14 OUT3
1OUT
1
8
Vcc
2OUT 2 13 OUT4 Vcc 3 － ＋ 2IN4 － ＋ 11 4IN+ 12 GND
1IN-
2
－ ＋
7
2OUT
1IN+
3
＋
－
6
2IN-
2IN+
5
10
4IN-
1IN-
6 － ＋ － ＋
9
3IN+
GN D
4
5
2IN+
1IN+
7
8
3IN-
SOIC8
LM393DR LM2903DR LM2903VQDR
TSSOP8
LM393PW R LM2903PW R LM2903VQPW R
MSOP8/VSSOP8
LM393DGKR LM2903DGKR
SOIC14
LM339DR LM2901DR LM2901VQDR
TSSOP14
LM339PW R LM2901PW R LM2901VQPW R
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
1/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR ●Absolute Maximum Ratings (Ta=25℃) Parameter Supply Voltage Input Differential Voltage Common-mode Input Operating Temperature Storage Temperature Range Maximum Junction Temperature Symbol Vcc-GND Vid Vicm Topr Tstg Tj 0 to +70 -65 to +150 +150 Ratings LM393 family LM339 family LM2903 family +36 ±36 -0.3 to +36
Technical Note
LM2901 family
Unit V V V
-40 to +125
℃ ℃ ℃
●Electric Characteristics ○LM393/339 family(Unless otherwise specified, Vcc=+5[V])
Limits Parameter Temperature Symbol range Min. 25℃ Input Offset Voltage (*1) VIO Full range 25℃ Input Offset Current (*1) IIO Full range 25℃ Input Bias Current (*1) IIB Full range 25℃ VICR Full range AVD 25℃ 25℃ IOH Full range 25℃ VOL Full range IOL 25℃ 25℃ Supply Current ICC Full range － － Response Time Tre 25℃ － (*1) Absolute value 0.3 － － 0.3 － － 1.3 2.5 － － － － 1.3 － － μs － 6 － － － 0.8 700 － 1 － 6 － － 16 0.8 700 － 2 mA RL=∞,Vcc=30[V] RL=5.1[kΩ],VRL=5[V],CL=15pF VIN=100[mVp-p], overdrive=5[mV] RL=5.1[kΩ],VRL=5[V], CL=15pF VIN=TTL-Level input step Vref=1.4[V] mA VID=-1[V],VOL=1.5[V] RL=∞,Vcc=5V 89 89 － － － 150 1 400 － － － 150 1 400 mV VID=-1[V],IOL=4[mA] 89 μA VID=1[V],VO=30[V] － 25 － － 200 0.1 Vcc-2.0 － － － 25 － － 200 0.1 Vcc-2.0 － － V/mA nA Vcc=15[V] VO=1.4 to 11.4[V], RL≧15[kΩ],VRL=15[V] VID=1[V],VO=5[V] 89 88 － － － － 400 Vcc-1.5 － － － － 400 Vcc-1.5 V － 88 － － － 25 250 250 － － － 25 150 250 nA VO=1.4[V] 88 － － － 5 9 50 － － － 5 9 50 nA VO=1.4[V] 88 － LM393 family Typ. 2 Max. 7 Min. － LM339 family Typ. 2 Max. 7 mV Unit condition Fig. No.
Vcc=5 to 30[V],VO=1.4[V] VIC=VIC(min)
88
Common-mode Input Voltage Range
Large Signal Differential Voltage Amplification
High Level Output Current
Low Level Output Voltage
Low Level Output Current
89
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
2/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR
Technical Note
○LM2903/2901 family(Unless otherwise specified, Vcc=+5[V])
Limits Parameter Symbol Temperature range LM2903 family Min. 25℃ Input Offset Voltage (*2) VIO Full range 25℃ Input Offset Current (*2) IIO Full range 25℃ IIB Full range 25℃ VICR Full range AVD 25℃ 25℃ IOH Full range 25℃ VOL 25℃ Full range Low Level Output Current IOL 25℃ － － － － 6 － Supply Current ICC 25℃ － － Response Time Tre 25℃ － 0.3 － － 0.3 － 1 1.3 2.5 － － － 1 1.3 2.5 － μs － 150 150 － 16 0.8 1 400 400 700 － 2 － － － － 6 － － 150 150 － 16 0.8 1 500 400 700 － 2 mA RL=∞,Vcc=MAX(*7) RL=5.1[Ω],VRL=5[V],CL=15pF VIN=100[mVp-p], Overdrive=5[mV] RL=5.1[kΩ],VRL=5[V], CL=15pF VIN=TTL-Level input step Vref=1.4[V] mA VID=-1[V], VOL=1.5[V] RL=∞,Vcc=5V 89 89 mV VIN(-)=1[V],VIN(+)=0[V] ISINK≦4[mA] 89 μA VID=1[V], VOH=MAX － 25 － － 100 0.1
Vcc-2.0
LM2901 family Min. － － － － － － － － 25 － Typ. 2 － 5 － 25 － － － 100 0.1 Max. 7
Unit
Condition
Fig. No
Typ. 2 － 5 － 25 － －
Max. 7 15 50 200 250 500
Vcc-1.5
－ － － － － － －
mV 15 50 nA 200 250 nA 500
Vcc-1.5
Vcc=5 to MAX),VO=1.4[V] VIC=VIC (min)
88
VO=1.4[V]
88
Input Bias Current (*2)
VO=1.4[V]
88
Common-mode Input Voltage Range
V
Vcc-2.0
－
88
Large Signal Differential Voltage Amplification
－ －
－ －
V/mV nA
Vcc=15[V],VOUT=1.4 to 11.4[V], RL≧15[kΩ],VRL=15[V] VID=1[V], VOH=5[V]
88
High Level Output Current
89
LM2901(*3) Low Level Output Voltage LM2901V(*3)
89
(*2) Absolute value (*3) Supply Voltage Maximum Value LM2901DR, LM2901PWR MAX=30[V], LM2901VQDR, LM2901VQPWR MAX=32[V]
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
3/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR ●Reference Data LM393 family
1000
LM393 family
Technical Note
1 .
0℃
LM393 family
1
LM393 family
POWER DISSIPATION [mW] .
800
LM393DGKR LM393PWR
0.8
SUPPLY CURRENT [mA]
0.8 SUPPLY CURRENT [mA]
36V 25℃
600
0.6
0.6
400
LM393DR
0.4
70℃
0.4
2V
200
0.2
0.2
5V
0 0 25 50
70
0
0
0 10 20 30 SUPPLY VOLTAGE [V] 40
75
100
125
0
10
AMBIENT TEMPERATURE [℃] .
20 30 40 50 60 70 AMBIENT TEMPER ATURE [℃]
80
Fig.1
Derating Curve
500 OUTPUT SATURATION VOLTAGE [mV]
70℃ LM393 family
Fig.2
Supply Current – Supply Voltage
500 OUTPUT SATU RATION VOLT AGE [mV]
LM393 family
Fig. 3
Supply Current – Ambient Temperature
2.0 LOW LEVEL OUTPUT VOLTAGE [V] 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 0 2 4 6 8
0℃ 70℃ 25℃ LM393 family
400
400
2V
300
25℃
300
5V
200
0℃
200
36V
100
100
0 0 10 20 30 SUPPLY VOLTAGE [V] 40
0 0 10 20 30 40 50 60 70 AMBIENT TEMPERATURE [℃] 80
10 12 14 16 18 20
Fig.4
Fig. 5
OUTPUT SINK CURRENT [mA]
Fig. 6
Output Saturation Voltage – Supply Voltage
(IOL=4[mA])
40 OUTPUT SINK CURR ENT [mA]
LM393 family
Output Saturation Voltage – Ambient Temperature
(IOL=4[mA])
8 INPUT OFFSET VOLTAGE [mV] 6 4 2 0 -2 -4 -6 -8
70℃ 0℃ 25℃ LM393 family
Low Level Output Voltage – Output Sink Current
(VCC=5[V])
8 INPUT OFFSET VOLTAGE [mV] 6 4 2 0 -2 -4 -6 -8
36V 2V 5V LM393 family
30
36V
5V
20
10
2V
0 0 10 20 30 40 50 60 70 AMBIEN T TEMPERATURE [℃] 80
0
10
20
30
40
0
10
20
30
40
50
60
70
80
SUPPLY VOLTAGE [V]
AMBIENT TEMPERATURE [℃]
Output Sink Current – Ambient Temperature
(VOUT=1.5[V])
160 140 INPUT BIAS CURRENT [nA]
LM393 family
Fig. 7
Input Offset Voltage – Supply Voltage
Fig. 8
Fig. 9
Input Offset Voltage – Ambient Temperature
.
160 140
LM393 family
50 40 INPUT OFFSET CURRENT [nA] 30 20 10 0 -10 -20 -30 -40 -50
0℃
LM393 family
INPUT BIAS CURRENT [nA]
120 100 80 60 40 20 0 0 10 20 30 40 SUPPLY VOLTAGE [V]
70℃ 0℃ 25℃
120 100 80 60 40 20 0 0 10 20 30 40 50 60 70 AMBIENT TEMPERATURE [℃] 80
2V 5V 36V
25℃ 70℃
0
10 20 30 SUPPLY VOLTAGE [V]
40
Fig. 10
Input Bias Current – Supply Voltage
Fig. 11
Input Bias Current – Ambient Temperature
Fig. 12
Input Offset Current – Supply Voltage
(*)The data above is ability value of sample, it is not guaranteed. LM393family:0[℃]~+70[℃]
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
4/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR ●Reference Data LM393 family
50 40 IN PUT OFFSET CU RRENT [nA] 30 20 10 0 -10 -20 -30 -40 -50 0 10 20 30 40 50 60 70 AMBIENT TEMPERATURE [℃] 80
2V 5V 36V
Technical Note
.
LM393 family
140 130 120 110 100 90 80 70 60 0
70℃ 0℃ 25℃
LM393 family
.
140 130
36V
LM393 family
LARGE SIGNAL VOLTAGE GAIN [dB]
LARGE SIGNAL VOLT AGE GAIN [dB]
120 110 100 90 80 70 60 0 10 20 30 40 50 60 70 AMBIENT TEMPERATURE [°C] 80
2V 5V
10 20 30 SUPPLY VOLTAGE [V]
40
Fig. 13
Input Offset Current – Ambient Temperature
160 140 120 100 80 60 40 0 10 20 30 SUPPLY VOLTAGE [V] 40
LM393 family
Fig. 14
.
Fig. 15
Large Signal Voltage Gain – Ambient Temperature
140 130 120 110 100 90 80 70 60 0 10 20 30 40 50 60 70 AMBIENT TEMPERAT URE [°C] 80
LM393 family
Large Signal Voltage Gain – Supply Voltage
POWER SUPPLY REJECTION RAT IO [dB] 140 130 120
36V LM393 family
0℃
25℃
110 100 90 80 70 60 0 10
2V
5V
70℃
20 30 40 50 60 70 AMBIENT TEMPERATURE [°C]
80
Fig. 16
Common Mode Rejection Ratio – Supply Voltage
.. 5
LM393 family
Fig. 17
Common Mode Rejection Ratio – Ambient Temperature
5 RESPONSE TIME (HIGH to LOW) [μ ｓ]
LM393 family
POWER SUPPLY REJECTION RATIO [dB]
COMMON MODE REJECTION RATIO[dB] .
Fig. 18
Power Supply Rejection Ratio – Ambient Temperature
RESPONSE T IME (LOW to HIGH) [μs]
. 4 3
5mV overdrive
4
3
5mV overdrive
2
20mV overdrive
2
20mV overdrive 100mV overdrive
1
100mV overdrive
1
0 0 10 20 30 40 50 60 70 AMBIENT TEMPERATURE [°C] 80
0 0 10 20 30 40 50 60 70 AMBIENT TEMPERATURE [°C] 80
Fig. 19
Response Time (Low to High) – Ambient Temperature
(VCC=5[V],VRL=5[V],RL=5.1[kΩ])
Fig. 20
Response Time (High to Low) –Ambient Temperature
(VCC=5[V],VRL=5[V],RL=5.1[kΩ])
(*)The data above is ability value of sample, it is not guaranteed. LM393family:0[℃]~+70[℃]
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
5/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR ●Reference Data LM339 family
1000
LM339 family
Technical Note
1
.
0℃
LM339 family
LM339 family
1
POWER DISSIPATION [mW] .
800
SUPPLY CURRENT [mA]
SUPPLY CURRENT [mA]
LM339PWR
0.8
25℃
0.8
36V 5V
600
0.6
0.6
400
LM339DR
0.4
70℃
0.4
2V
200
0.2
0.2
0 0 25 50
70
0
0 0 10 20 30 SUPPLY VOLTAGE [V] 40 0 10 20 30 40 50 60 70 AMBIENT TEMPER ATURE [℃] 80
75
100
125
AMBIENT TEMPERATURE [℃] .
Fig.21
Derating Curve
LM339 family
Fig.22
Supply Current – Supply Voltage
500 OUTPUT SATU RATION VOLT AGE [mV]
LM339 family
Fig. 23
Supply Current – Ambient Temperature
2.0
LOW LEVEL OUTPUT VOLTAGE [V]
LM339 family
500 OUTPUT SATURATION VOLTAGE [mV]
70℃
1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 0 2 4 6 8
0℃ 70℃ 25℃
400
400
2V
300
25℃
300
5V
200
0℃
200
36V
100
100
0 0 10 20 30 SUPPLY VOLTAGE [V] 40
0 0 10 20 30 40 50 60 70 AMBIENT TEMPERATURE [℃] 80
10 12 14 16 18 20
Fig.24
Output Saturation Voltage – Supply Voltage
(IOL=4[mA])
40 OUTPUT SINK CURR ENT [mA]
LM339 family
Output Saturation Voltage – Ambient Temperature
(IOL=4[mA])
8 INPUT OFFSET VOLTAGE [mV] 6 4 2 0 -2 -4 -6 -8
70℃ 0℃ 25℃ LM339 family
Fig. 25
OUTPUT SINK CURRENT [mA]
Low Level Output Voltage – Output Sink Current
(VCC=5[V])
8 INPUT OFFSET VOLTAGE [mV] 6 4 2 0 -2 -4 -6 -8
36V 2V 5V LM339 family
Fig. 26
30
36V
20
5V
10
2V
0 0 10 20 30 40 50 60 70 AMBIEN T TEMPERATURE [℃] 80
0
10
20
30
40
0
10
20
30
40
50
60
70
80
SUPPLY VOLTAGE [V]
AMBIENT TEMPERATURE [℃]
Fig. 27
Output Sink Current – Ambient Temperature
(VOUT=1.5[V])
160 140 INPUT BIAS CURRENT [nA]
LM339 family
Fig. 28
Input Offset Voltage – Supply Voltage
160 140 INPUT BIAS CURRENT [nA] 120 100 80 60 40 20 0
2V 5V 36V LM339 family
Fig. 29
Input Offset Voltage – Ambient Temperature
50 40 INPUT OFFSET CURRENT [nA] 30 20 10 0 -10 -20 -30 -40 -50
25℃ 70℃ 0℃ LM339 family
120 100 80 60 40 20 0 0 10 20 30 40 SUPPLY VOLTAGE [V]
70℃ 0℃ 25℃
.
0
10
20 30 40 50 60 70 AMBIENT TEMPERATURE [℃]
80
0
10 20 30 SUPPLY VOLTAGE [V]
40
Input Bias Current – Supply Voltage
Fig. 30
Fig. 31
Input Bias Current – Ambient Temperature
Fig. 32
Input Offset Current – Supply Voltage
(*)The data above is ability value of sample, it is not guaranteed. LM339family:0[℃]~+70[℃]
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
6/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR ●Reference Data LM339 family
40 IN PUT OFFSET CU RRENT [nA] 30 20 10 0 -10 -20 -30 -40 -50 0 10 20 30 40 50 60 70 AMBIENT TEMPERATURE [℃] 80
2V 5V 36V
Technical Note
.
50
.
LM339 family
140 130 120 110 100 90 80 70 60 0
70℃ 0℃ 25℃
LM339 family
140 130
36V
LM339 family
LARGE SIGNAL VOLTAGE GAIN [dB]
LARGE SIGNAL VOLT AGE GAIN [dB]
120 110 100 90 80 70 60 0 10 20 30 40 50 60 70 AMBIENT TEMPERATURE [°C] 80
2V 5V
10 20 30 SUPPLY VOLTAGE [V]
40
Fig. 33
Input Offset Current – Ambient Temperature
POWER SUPPLY REJECTION RAT IO [dB]
COMMON MODE REJECTION RATIO[dB] . 160 140 120
0℃ LM339 family
Fig. 34
Large Signal Voltage Gain – Supply Voltage
. POWER SUPPLY REJECTION RATIO [dB]
Fig. 35
Large Signal Voltage Gain – Ambient Temperature
140 130 120 110 100 90 80 70 60 0 10 20 30 40 50 60 70 AMBIENT TEMPERAT URE [°C] 80
LM339 family
140 130 120
36V
LM339 family
25℃
110 100 90 80 70 60 0 10
2V
5V
100 80 60 40 0 10 20 30 SUPPLY VOLTAGE [V] 40
70℃
20 30 40 50 60 70 AMBIENT TEMPERATURE [°C]
80
Fig. 36
Common Mode Rejection Ratio – Supply Voltage
.. 5
LM339 family
Fig. 37
Common Mode Rejection Ratio – Ambient Temperature
5 RESPONSE TIME (HIGH to LOW) [μ ｓ]
LM339 family
Fig. 38
Power Supply Rejection Ratio – Ambient Temperature
RESPONSE T IME (LOW to HIGH) [μs]
. 4 3
5mV overdrive
4
3
5mV overdrive
2
20mV overdrive
2
20mV overdrive 100mV overdrive
1
100mV overdrive
1
0 0 10 20 30 40 50 60 70 AMBIENT TEMPERATURE [°C] 80
0 0 10 20 30 40 50 60 70 AMBIENT TEMPERATURE [°C] 80
Fig. 39
Response Time (Low to High) – Ambient Temperature
(VCC=5[V],VRL=5[V],RL=5.1[kΩ])
Fig. 40
Response Time (High to Low) –Ambient Temperature
(VCC=5[V],VRL=5[V],RL=5.1[kΩ])
(*)The data above is ability value of sample, it is not guaranteed. BA10393F:-40[℃]~+70[℃] ℃]～+85[℃] *)上記のデータはサンプルの実力値であり、保証するものではありません。BA10393F:-40[
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
7/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR ●Reference Data LM2903 family
800 1000
POWER DISSIPATION [mW] POWER DISSIPATION Pd [mV]
LM2903 family
Technical Note
1.6 1.4
LM2903 family
LM2903 family
1.6 1.4
600
SUPPLY CURRENT [mA]
SUPPLY CURRENT [mA]
800
LM2903PT
600
1.2 1.0 0.8 0.6 0.4 0.2
105℃ 125℃ -40℃ 25℃
1.2 1.0 0.8 0.6 0.4 0.2 0.0
2V 36V 5V
LM2903DGKR
400
400
200
200
LM2903DT
00 00
25 25
0.0
AMBIENT TEMPERTURE [℃] 50 50 75 75 100 100 125 125 . 150 150
0
10
20
30
40
-50
-25
0
25
50
75
100 125 150
AMBIENT TEMPERATURE
[℃]
SUPPLY VOLTAGE [V]
AMBIENT TEMPERATURE [℃]
Fig. 41
Derating Curve
LM2903 family
Fig. 42
Supply Current – Supply Voltage
LM2903 family
Fig. 43
Supply Current – Ambient Temperature
LM2903 family
MAXIMUM OUTPUT VOLTAGE [mV]
200
200
2 1.8
MAXIMUM OUTPUT VOLTAGE [mV]
150
125℃ 105℃
150
OUTPUT VOLTAGE [V]
1.6 1.4 1.2 1 0.8 0.6 0.4 0.2
-40℃ 105℃ 125℃ 25℃
2V
100
100
5V
50
25℃ -40℃
50
36V
0 0 10 20 30 40
0 -50 -25 0 25 50 75 100 125 150
0 0 2 4 6 8 10 12 14
16
18
20
SUPPLY VOLTAGE [V]
SUPPLY VOLTAGE [V]
OUTPUT SINK CURRENT [mA]
Fig. 44
Output Saturation Voltage – Supply Voltage
(IOL=4[mA])
LM2903 family
Fig. 45
Output Saturation Voltage – Ambient Temperature
(IOL=4[mA])
LM2903 family
Fig. 46
Low Level Output Voltage – Output Sink Current
(VCC=5[V])
LM2903 family
40
8
8 INPUT OFFSET VOLTAGE [mV] 6 4
2V
INPUT OFFSET VOLTAGE [mV]
OUTPUT SINK CURRENT [mA]
6 4 2 0 -2 -4 -6 -8
25℃ 105℃ 125℃ -40℃
30
5V
36V
2 0 -2 -4 -6 -8
5V 36V
20
2V
10
0 -50 -25 0 25 50 75 100 125 150
0
10
20
30
40
-50
-25
0
25
50
75
100 125 150
AMBIENT TEMPERATURE [℃]
SUPPLY VOLTAGE [V]
AMBIENT TEMPERATURE [℃]
Fig. 47
Output Sink Current – Ambient Temperature
(VOUT=1.5[V])
LM2903 family
Fig. 48
Input Offset Voltage – Supply Voltage
LM2903 family
Fig. 49
Input Offset Voltage – Ambient Temperature
LM2903 family
160
160 INPUT OFFSET CURRENT[nA]
50 40 30 20 10 0 -10 -20 -30 -40 -50 -50 -25 0 25 50 75 100 125 150 0 10 20 30 40
105℃ 125℃ -40℃ 25℃
INPUT BIAS CURRENT [nA]
INPUT BIAS CURRENT [nA]
140 120 100 80 60 40 20 0 0 5 10 15 20 25 30 35
105℃ 125℃ -40℃ 25℃
140 120 100 80 60 40 20 0
5V 2V
36V
SUPPLY VOLTAGE [V]
Fig. 50
AMBIENT TEMPERATURE [℃]
Fig. 51
SUPPLY VOLTAGE [V]
Fig. 52
Input Bias Current – Supply Voltage
Input Bias Current – Ambient Temperature
Input Offset Current – Supply Voltage
(*)The data above is ability value of sample, it is not guaranteed.LM2903family:-40[℃]～+125[℃]
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
8/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR ●Reference Data LM2903 family
LM2903 family
Technical Note
50
140
LM2903 family
LM2903 family
140
LARGE SINGAL VOLTAGE GAIN [dB]
INPUT OFFSET CURRENT [nA]
40 30 20 10 0 -10 -20 -30 -40 -50 -50 -25 0 25 50 75 100 125 150
5V 36V 2V
LARGE SINGAL VOLTAGE GAIN [dB]
130 120 110 100 90 80 70 60 0 10
125℃
105℃
130
36V
120 110 100 90 80 70 60 -50 -25 0 25 50 75 100 125 150
15V 5V
25℃
-40℃
20
30
40
AMBIENT TEMPERATURE [℃]
SUPPLY VOLTAGE [V]
AMBIENT TEMPERATURE [℃]
Fig. 53
Input Offset Current – Ambient Temperature
LM2903 family
Fig. 54
Large Signal Voltage Gain – Supply Voltage
LM2903 family
Fig. 55
Large Signal Voltage Gain – Ambient Temperature
LM2903 family
COMMON MODE REJECTION RATIO [dB]
COMMON MODE REJECTION RATIO [dB]
160 140 120
105℃
150
6
INPUT OFFSET VOLTAGE [mV]
25℃
105℃
125 100 75
5V
36V
4
-40℃
125℃
2
125℃
100 80 60 40 0 10 20 30 40
0 -2 -4 -6
-40℃
25℃
50 25 0 -50 -25 0 25
2V
50
75
100 125 150
-1
0
1
2
3
4
5
SUPPLY VOLTAGE [V]
AMBIENT TEMPERATURE [℃]
INPUT VOLTAGE [V]
Fig. 56
Common Mode Rejection Ratio – Supply Voltage
LM2903 family
Fig. 57
Common Mode Rejection Ratio – Ambient Temperature
LM2903 family
Fig. 58
Input Offset Voltage – Input Voltage
(VCC=5V)
LM2903 family
POWER SUPPLY REJECTION RATIO [dB]
180 160 140 120 100 80 60 -50 -25 0 25 50 75 100 125 150
RESPONSE TIME (LOW TO HIGH)[μs]
RRESPONSE TIME (LOW TO HIGH)[μs]
200
5
5
4
4
3
3
5mV overdrive
2
125℃ 105℃ 25℃ -40℃
2
100mV overdrive 20mV overdrive
1
1
0 -100 -80 -60 -40 -20 0
0 -50 -25 0 25 50 75 100 125 150
AMBIENT TEMPERATURE [℃]
OVER DRIVE VOLTAGE [V]
AMBIENT TEMPERATURE [℃]
Fig. 59
Power Supply Rejection Ratio – Ambient Temperature
LM2903 family
Fig. 60
Response Time (Low to High) – Over Drive Voltage
LM2903 family
Fig. 61
Response Time (Low to High) – Ambient Temperature
(VCC=5[V],VRL=5[V],RL=5.1[kΩ])
(VCC=5[V],VRL=5[V],RL=5.1[kΩ])
RESPONSE TIME (HIGH TO LOW)[μs]
5
RESPONSE TIME (HIGH TO LOW)[μs]
5
4
4
100mV overdrive 20mV overdrive 5mV overdrive
3
125℃ 105℃ 25℃ -40℃
3
2
2
1
1
0 0 20 40 60 80 100
0 -50 -25 0 25 50 75 100 125 150
OVER DRIVE VOLTAGE [V]
AMBIENT TEMPERATURE [℃]
Fig. 62
Response Time (High to Low) – Over Drive Voltage
(VCC=5[V],VRL=5[V],RL=5.1[kΩ])
Fig. 63
Response Time (High to Low) – Ambient Temperature
(VCC=5[V],VRL=5[V],RL=5.1[kΩ])
(*)The data above is ability value of sample, it is not guaranteed. LM2903family:-40[℃]～+125[℃]
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
9/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR ●Reference Data LM2901 family
1000 1000
LM2901 family
Technical Note
2.0 1.8
LM2901 family
1.6 1.4
LM2901 family
POWER DISSIPATION Pd [mW]
POWER DISSIPATION [mW]
SUPPLY CURRENT [mA]
SUPPLY CURRENT [mA]
800 800
1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2
105℃ -40℃
25℃
LM290PWR
600 600
1.2 1.0 0.8 0.6 0.4 0.2 0.0
2V 36V 5V
400 400
LM2901DR
200 200
125℃
00 0
0
0.0
AMBIENT TEMPERATURE [℃] AMBIENT TEMPERATURE [℃]
25
25
50
50
75
75
100
100
125
125
150
150
0
10
20
30
40
-50
-25
0
25
50
75
100 125 150
SUPPLY VOLTAGE [V]
AMBIENT TEMPERATURE [℃]
Fig. 64
Fig. 65
Supply Current – Supply Voltage
Fig. 66
Supply Current – Ambient Temperature
LM2901 family
Derating Curve
LM2901 family
200
200
LM2901 family
2 1.8
MAXIMUM OUTPUT VOLTAGE [mV]
MAXIMUM OUTPUT VOLTAGE [mV]
150
125℃
150
OUTPUT VOLTAGE [V]
1.6 1.4 1.2 1 0.8 0.6 0.4 0.2
-40℃ 105℃ 125℃ 25℃
105℃
2V
100
100
5V
50
25℃ -40℃
50
36V
0 0 10 20 30 40
0 -50 -25 0 25 50 75 100 125 150
0 0 2 4 6 8 10 12 14 16 18 20
SUPPLY VOLTAGE [V]
SUPPLY VOLTAGE [V]
OUTPUT SINK CURRENT [mA]
Fig. 67
Output Saturation Voltage – Supply Voltage
(IOL=4[mA])
40
LM2901 family
Fig. 68
Output Saturation Voltage – Ambient Temperature
(IOL=4[mA])
8
LM2901 family
Fig. 69
Low Level Output Voltage – Output Sink Current
(VCC=5[V])
8
LM2901 family
INPUT OFFSET VOLTAGE [mV]
INPUT OFFSET VOLTAGE [mV]
OUTPUT SINK CURRENT [mA]
6 4 2 0 -2 -4 -6 -8
25℃ 105℃ 125℃ -40℃
6 4
2V
30
5V
36V
2 0 -2 -4 -6 -8
5V 36V
20
2V
10
0 -50 -25 0 25 50 75 100 125 150
0
10
20
30
40
-50
-25
0
25
50
75
100 125 150
AMBIENT TEMPERATURE [℃]
SUPPLY VOLTAGE [V]
AMBIENT TEMPERATURE [℃]
Fig. 70
Output Sink Current – Ambient Temperature
(VOUT=1.5[V])
160
LM2901 family
Fig. 71
Input Offset Voltage – Supply Voltage
LM2901 family
Fig. 72
Input Offset Voltage – Ambient Temperature
LM2901 family
160
50
INPUT OFFSET CURRENT[nA]
INPUT BIAS CURRENT [nA]
INPUT BIAS CURRENT [nA]
140 120 100 80 60 40 20 0 0 5 10 15 20 25 30 35
105℃ 125℃ -40℃ 25℃
140 120 100 80 60 40 20 0 -50 -25 0 25 50 75 100 125 150
5V 2V
40 30 20 10 0 -10 -20 -30 -40 -50 0 10 20 30 40
105℃ 125℃ -40℃ 25℃
36V
SUPPLY VOLTAGE [V]
AMBIENT TEMPERATURE [℃]
SUPPLY VOLTAGE [V]
Fig. 73
Input Bias Current – Supply Voltage
Fig. 74
Input Bias Current – Ambient Temperature
Fig. 75
Input Offset Current – Supply Voltage
(*)The data above is ability value of sample, it is not guaranteed. LM901family:-40[℃]～+125[℃]
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
10/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR ●Reference Data LM2901 family
LM2901 family LM2901 family
Technical Note
LM2901 family
50
140
140
LARGE SINGAL VOLTAGE GAIN [dB]
INPUT OFFSET CURRENT [nA]
40 30 20 10 0 -10 -20 -30 -40 -50 -50 -25 0 25 50 75 100 125 150
5V 36V 2V
LARGE SINGAL VOLTAGE GAIN [dB]
130 120 110 100
125℃
105℃
130 120 110 100
36V
25℃
90 80 70 60 0 10 20
-40℃
15V
5V
90 80 70 60 -50 -25 0 25 50 75 100 125 150
30
40
AMBIENT TEMPERATURE [℃]
SUPPLY VOLTAGE [V]
AMBIENT TEMPERATURE [℃]
Fig. 76
Input Offset Current – Ambient Temperature
LM2901 family
Fig. 77
Large Signal Voltage Gain – Supply Voltage
LM2901 family
Fig. 78
Large Signal Voltage Gain – Ambient Temperature
LM2901 family
COMMON MODE REJECTION RATIO [dB]
COMMON MODE REJECTION RATIO [dB]
160 140 120 100 80 60 40 0 10 20 30 40
150
6
25℃
INPUT OFFSET VOLTAGE [mV]
105℃
125 100 75 50 25 0 -50 -25 0 25
36V
4
-40℃
105℃
125℃
2
125℃
5V 2V
0 -2 -4 -6
-40℃
25℃
50
75
100 125 150
-1
0
1
2
3
4
5
SUPPLY VOLTAGE [V]
AMBIENT TEMPERATURE [℃]
INPUT VOLTAGE [V]
Fig. 79
Common Mode Rejection Ratio – Supply Voltage
LM2901 family
Fig. 80
Common Mode Rejection Ratio – Ambient Temperature
LM2901 family
Fig. 81
Input Offset Voltage – Input Voltage
(VCC=5V)
LM2901 family
POWER SUPPLY REJECTION RATIO [dB]
180 160 140 120 100 80 60 -50 -25 0 25 50 75 100 125 150
RESPONSE TIME (LOW TO HIGH)[μs]
RRESPONSE TIME (LOW TO HIGH)[μs]
200
5
5
4
4
3
3
5mV overdrive
100mV overdrive
2
125℃ 105℃ 25℃ -40℃
2
20mV overdrive
1
1
0 -100 -80 -60 -40 -20 0
0 -50 -25 0 25 50 75 100 125 150
AMBIENT TEMPERATURE [℃]
OVER DRIVE VOLTAGE [V]
AMBIENT TEMPERATURE [℃]
Fig. 82
Power Supply Rejection Ratio – Ambient Temperature
RESPONSE TIME (HIGH TO LOW)[μs]
5
LM2901 family
Fig. 83
Response Time (Low to High) – Over Drive Voltage
5
Fig. 84
(VCC=5[V],VRL=5[V],RL=5.1[kΩ])
Response Time (Low to High) – Ambient Temperature
(VCC=5[V],VRL=5[V],RL=5.1[kΩ])
LM2901 family
RESPONSE TIME (HIGH TO LOW)[μs]
4
4
100mV overdrive
3
3
20mV overdrive 5mV overdrive
125℃ 105℃ 25℃
2
2
-40℃
1
1
0 0 20 40 60 80 100
0 -50 -25 0 25 50 75 100 125 150
OVER DRIVE VOLTAGE [V]
AMBIENT TEMPERATURE [℃]
Response Time (High to Low) – Over Drive Voltage
(VCC=5[V],VRL=5[V],RL=5.1[kΩ])
Fig. 85
Fig. 86
Response Time (High to Low) – Ambient Temperature
(VCC=5[V],VRL=5[V],RL=5.1[kΩ])
(*)The data above is ability value of sample, it is not guaranteed. LM901family:-40[℃]～+125[℃]
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
11/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR ●Circuit Diagram
Technical Note
Vcc
OUT IN+
IN-
GND
Fig.87 Circuit Diagram (each Comparator)
●Measurement circuit 1 NULL Method measurement condition Parameter Input Offset Voltage Input Offset Current Input Bias Current Large Signal Voltage Gain VF VF1 VF2 VF3 VF4 VF5 VF6 S1 ON S2 ON S3 LM393/LM339 family Vcc GND 0 0 0 0 0 0 EK -1.4 -1.4 -1.4 -1.4 -1.4 -11.4 VICR 0 0 0 0 0 0 Vcc,GND,EK,VICR Unit：[V］ LM2903/LM2901 family Calculation Vcc GND EK VICR 5 to 30 5 5 5 15 15 0 0 0 0 0 0 -1.4 -1.4 -1.4 -1.4 -1.4 -11.4 0 0 0 0 0 0 1 2 3 4
ON 5 to 30 ON ON ON 5 5 5 15 15
OFF OFF OFF ON ON ON OFF ON
－Calculation－
1.Input offset voltage (VIO)
Vio VF1 1+ Rf /Rs [ V]
S1 Rf 50[kΩ] RK 500[kΩ] 0.1[μF] +15[V ] Ri＝ 10[kΩ] Ri＝ 10[kΩ] RS＝ 50[Ω] DUT S3 RK 500[kΩ] NULL 1000[pF] 0.1[μF]
2.Input offset current (IIO)
Iio VF2 - VF1 Ri (1+ R f / R s) [A]
V ICR RS＝ 50[Ω]
Vcc
EK
3.Input bias current (IIb)
Ib VF4 - VF3 2× R i (1+ Rf / Rs) [A]
50[kΩ]
S2
GND
RL V RL
-15[V ]
V VF
4.Large signal differential voltage gain (AVD)
AV 20× Log 10× (1+ Rf /Rs) VF6 - VF5 [dB]
Fig.88 Measurement Circuit1 (each Comparator)
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
12/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR ●Measurement Circuit2 Switch Condition SW No. Supply Current Low Level Output Current Low Level Output Current High Level Output Current Response Time
― SW 1 OFF OFF OFF OFF ON SW 2 OFF ON ON ON OFF SW 3 OFF ON ON ON ON SW 4 OFF OFF OFF OFF ON SW 5 OFF ON OFF OFF OFF
Technical Note
SW 6 OFF ON OFF OFF ON
SW 7 OFF OFF ON ON OFF
VOL=1.5[V] IOL=4[mA] VOH=36[V] RL=5.1[kΩ] VRL=5[V]
Vcc 5[V] A
－
SW1 SW2 SW3 GND 0[V]
＋
SW4 SW5 SW6 SW7
RL A V
VIN-
VIN+
VRL
VOL/VOH
Fig.89 Measurement Circuit2 (each channel)
Input waveform VIN +100[mV] 0[V] VIN
Input waveform over drive
0[V] over drive
+100[mV]
VUOT 5[V]
VUOT Output waveform 5[V]
Output waveform
2.5[V] 2.5[V] 0[V] Tre LH 0[V] Tre LH
Fig.90 Response Time
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
13/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR ●Description of Electrical Characteristics
Technical Note
Described below are descriptions of the relevant electrical terms. Please note that item names, symbols, and their meanings may differ from those on another manufacturer’s documents. 1. Absolute maximum ratings The absolute maximum ratings are values that should never be exceeded, since doing so may result in deterioration of electrical characteristics or damage to the part itself as well as peripheral components. 1.1 Power supply voltage (Vcc/GND) Expresses the maximum voltage that can be supplied between the positive and negative power supply terminals without causing deterioration of the electrical characteristics or destruction of the internal circuitry. 1.2 Differential input voltage (VID) Indicates the maximum voltage that can be supplied between the non-inverting and inverting terminals without damaging the IC. 1.3 Input common-mode voltage range (VICR) Signifies the maximum voltage that can be supplied to non-inverting and inverting terminals without causing deterioration of the electrical characteristics or damage to the IC itself. Normal operation is not guaranteed within the input common-mode voltage range of the maximum ratings – use within the input common-mode voltage range of the electric characteristics instead. 1.4 Operating temperature range and storage temperature range (Topr,Tstg) The operating temperature range indicates the temperature range within which the IC can operate. The higher the ambient temperature, the lower the power consumption of the IC. The storage temperature range denotes the range of temperatures the IC can be stored under without causing excessive deterioration of the electrical characteristics. 1.5 Power dissipation (Pd) Indicates the power that can be consumed by a particular mounted board at ambient temperature (25°C). For packaged products, Pd is determined by maximum junction temperature and the thermal resistance. 2. Electrical characteristics 2.1 Input offset voltage (VIO) Signifies the voltage difference between the non-inverting and inverting terminals. It can be thought of as the input voltage difference required for setting the output voltage to 0V. 2.2 Input offset current (IIO) Indicates the difference of the input bias current between the non-inverting and inverting terminals. 2.3 Input bias current (IIB) Denotes the current that flows into or out of the input terminal, it is defined by the average of the input bias current at the non-inverting terminal and the input bias current at the inverting terminal. 2.4 Input common-mode voltage range (VICR) Indicates the input voltage range under which the IC operates normally. 2.5 Large signal differential voltage gain (AVD) The amplifying rate (gain) of the output voltage against the voltage difference between the non-inverting and inverting terminals, it is (normally) the amplifying rate (gain) with respect to DC voltage. AVD = (output voltage fluctuation) / (input offset fluctuation) 2.6 Supply current (ICC) Indicates the current of the IC itself that flows under specific conditions and during no-load steady state. 2.7 Low level output current (IOL) Denotes the maximum current that can be output under specific output conditions. 2.8 Low level output voltage (VOL) Signifies the voltage range that can be output under specific output conditions. 2.9 High level output current (IOH) Indicates the current that flows into the IC under specific input and output conditions. 2.10 Response time (tre) The interval between the application of input and output conditions. 2.11 Common-mode rejection ratio (CMRR) Denotes the ratio of fluctuation of the input offset voltage when the in-phase input voltage is changed (DC fluctuation). CMRR = (change of input common-mode voltage) / (input offset fluctuation) 2.12 Power supply rejection ratio (PSRR) Signifies the ratio of fluctuation of the input offset voltage when the supply voltage is changed (DC fluctuation). PSRR = (change in power supply voltage) / (input offset fluctuation)
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
14/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR ●Derating Curves
800
Technical Note
1000
POWER DISSIPATION Pd [mW]
POWER DISSIPATION Pd [mW]
LM393PWR LM2903PWR/VQPWR
600
800
LM339PWR LM2901PWR/VQPWR LM339DR LM2901DR/VQDR
LM393PWR LM2903PWR/VQPWR
600
400
LM393DR LM2903DR/VQDR
400
200
200
0 0 25 50 75 100 125 150
0 0 25 50 75 100 125 150
AMBIENT TEMPERATURE [℃]
AMBIENT TEMPERATURE [℃]
LM393DR/PWR/DGKR LM2903DR/PWR/DGKR/VQDR/VQPWR
Power Dissipation
LM339DR/PWR LM2901DR/PWR/VQDR/VQPWR
Power Dissipation
Package SOIC8 (*8) TSSOP8 (*6) MSOP8/VSSOP8 (*7)
Pd[W] 450 500 470
θja [℃/W] 3.6 4.0 3.76
θja = (Tj-Ta)/Pd[℃/W]
Package SOIC14 TSSOP14
Pd[W] 610 870
θja [℃/W] 4.9 7.0
θja = (Tj-Ta)/Pd[℃/W]
Fig.91 Derating Curves ●Precautions
1) Unused circuits When there are unused circuits it is recommended that they be connected as in Fig.92, setting the non-inverting input terminalto a potential within the in-phase input voltage range (VICR). 2) Input terminal voltage Applying GND + 36V to the input terminal is possible without causing deterioration of the electrical characteristics or destruction, irrespective of the supply voltage. However, this does not ensure normal circuit operation. Please note that the circuit operates normally only when the input voltage is within the common mode input voltage range of the electric characteristics.
－ ＋ V cc
GND
Fig.92 Disable circuit example
3) Power supply (single / dual) The op-amp operates when the specified voltage supplied is between Vcc and GND. Therefore, the single supply op-amp can be used as a dual supply op-amp as well. 4) Power dissipation Pd Using the unit in excess of the rated power dissipation may cause deterioration in electrical characteristics due to a rise in chip temperature, including reduced current capability. Therefore, please take into consideration the power dissipation (Pd) under actual operating conditions and apply a sufficient margin in thermal design. Refer to the thermal derating curves for more information. 5) Short-circuit between pins and erroneous mounting Incorrect mounting may damage the IC. In addition, the presence of foreign particles between the outputs, the output and the power supply, or the output and GND may result in IC destruction. 6) Terminal short-circuits When the output and Vcc terminals are shorted, excessive output current may flow, resulting in undue heat generation and, subsequently, destruction. 7) Operation in a strong electromagnetic field Operation in a strong electromagnetic field may cause malfunctions. 8) Radiation This IC is not designed to withstand radiation. 9) IC handing Applying mechanical stress to the IC by deflecting or bending the board may cause fluctuations in the electrical characteristics due to piezoelectric (piezo) effects. 10) Board inspection Connecting a capacitor to a pin with low impedance may stress the IC. Therefore, discharging the capacitor after every process is recommended. In addition, when attaching and detaching the jig during the inspection phase, ensure that the power is turned OFF before inspection and removal. Furthermore, please take measures against ESD in the assembly process as well as during transportation and storage.
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
15/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR ●Ordering part number
Technical Note
L
M
2
9
0
3
V
Q
D
Package type
D : SOIC PW : TSSOP DGK : MSOP/VSSOP
R
Packaging and forming specification R: Embossed tape and reel
Family name LM393 LM339 LM2901 LM2903
Operating Voltage
VQ : Tested to 32V None : Tested to 30V
SOIC8
4.9±0.2 (MAX 5.25 include BURR) ° 4° +6° −4
0.45Min.
Tape Quantity Direction of feed Embossed carrier tape 2500pcs
8
7
6
5
6.0±0.3
3.9±0.2
( reel on the left hand and you pull out the tape on the right hand
The direction is the 1pin of product is at the upper left when you hold
)
1
2
3
4
0.545
1.375±0.1
0.2±0.1 S
0.175
1.27
0.42±0.1 0.1 S
1pin (Unit : mm) (Unit Reel
Direction of feed
∗ Order quantity needs to be multiple of the minimum quantity.
SOIC14
8.65 ± 0.1 (Max 9.0 include BURR)
14 8
° 4° +6° −4
Tape Quantity
Embossed carrier tape 2500pcs
6.0 ± 0.2 3.9 ± 0.1
0.65± 0.15
1.05± 0.2
Direction of feed
( reel on the left hand and you pull out the tape on the right hand
The direction is the 1pin of product is at the upper left when you hold
)
0.515
1.65MAX
1
1PIN MARK
7
+0.05 0.22 −0.03
S 1.375 ± 0.075 0.175 ± 0.075
1.27
+0.05 0.42 −0.04
0.08 S 0.08 M
1pin (Unit : mm) Reel
Direction of feed
∗ Order quantity needs to be multiple of the minimum quantity.
TSSOP8
3.0 ± 0.1 (MAX 3.35 include BURR)
8 7 6 5
4±4
Tape Quantity
Embossed carrier tape 2500pcs
6.4 ± 0.2 4.4 ± 0.1
0.5 ± 0.15
Direction of feed
1.0 ± 0.2
( reel on the left hand and you pull out the tape on the right hand
The direction is the 1pin of product is at the upper left when you hold
)
1
2
3
4
1.2MAX
0.525
1PIN MARK S
+0.05 0.145 −0.03
1.0 ± 0.05
0.1 ± 0.05
0.08 S +0.05 0.245 −0.04 0.65
0.08
M
1pin (Unit : mm) Reel
Direction of feed
∗ Order quantity needs to be multiple of the minimum quantity.
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
16/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR
Technical Note
TSSOP14
5.0±0.1 (Max 5.35 include BURR) 4 ±4
14 8
Tape Quantity Direction of feed Embossed carrier tape 2500pcs
6.4±0.2 4.4±0.1
0.5±0.15
0.55
1
7
1PIN MARK S
+0.05 0.145 −0.03
1.2MAX
1.0±0.05
0.1±0.05
0.08 S 0.65 +0.05 0.245 −0.04 0.08
M
1.0±0.2
( reel on the left hand and you pull out the tape on the right hand
The direction is the 1pin of product is at the upper left when you hold
)
1pin (Unit : mm) Reel
Direction of feed
∗ Order quantity needs to be multiple of the minimum quantity.
MSOP / VSSOP8
3.0 ± 0.1 (MAX 3.35 include BURR)
8 7 6 5
4±4
Tape Quantity
Embossed carrier tape 2500pcs
4.9 ± 0.2
3.0 ± 0.1
0.45 ± 0.15
Direction of feed
0.95 ± 0.2
( reel on the left hand and you pull out the tape on the right hand
The direction is the 1pin of product is at the upper left when you hold
)
1
2
3
1PIN MARK S
4
1.1MAX
0.525
+0.05 0.145 −0.03
0.85±0.05
0.1±0.05
0.08 S +0.05 0.32 −0.04 0.65 0.08
M
1pin (Unit : mm) Reel
Direction of feed
∗ Order quantity needs to be multiple of the minimum quantity.
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
17/17
2011.06 - Rev.B
Notice
Notes
No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
R1120A
工商网监
湘ICP备2023018690号
