MCR03ERTF6801

Thick Film Chip Resistors MCR Series < Not for Automotive application > Datasheet Features 1) Full line up from ultra small size (01005) to 2512 with jumper type. 2) ROHM resistors have obtained ISO9001/ISO/TS16949 certification. Size Part No. MCR006 (mm) (inch) 0603 0201 MCR01 1005 0402 MCR03 1608 0603 MCR10 2012 0805 MCR18 3216 1206 MCR25 3225 1210 MCR50 5025 2010 MCR100 6432 2512 Packing Specification Type Code Quantity / Reel YRT 15,000 Paper tape (2mm pitch) MRT 10,000 ERT 5,000 Paper tape (4mm pitch) JRT 4,000 Embossed tape (4mm pitch) Part Number Description M C R 0 0 6 Part No. Size (mm [inch]) MCR 006 (0603 [0201]) 01 (1005 [0402]) 03 (1608 [0603]) 10 (2012 [0805]) 18 (3216 [1206]) 25 (3225 [1210]) 50 (5025 [2010]) 100 (6432 [2512]) (Micro chip resistors) Y R T Type Code J 1 0 0 Resistance Tolerance Nominal Resistance D ( ±0.5% ) F ( ±1% ) J ( ±5% ) (Including jumper type) Resistance code, 3 or 4 digits. 000 denotes jumper type. Resistance tolerance D,F J Resistance code : : 4 digits 3 digits Ex.) 1Ω = 1R0 ( ±5% ) 9.1 Ω = 9R1 ( ±5% ) 10 Ω = 10R0 ( ±0.5%,±1% ) 100 ( ±5% ) 2.2M Ω = 2204 ( ±1% ) 225 ( ±5% ) www.rohm.com c 2015 ROHM Co., Ltd. All rights reserved. ○ 1/6 2015.02 - Rev.F Datasheet MCR series < Not for Automotive application > Products List Part No. Type Code Rated Power Limiting Element (70°C) Voltage (W) MCR006 MCR01 MCR03 YRT MRT ERT (V) 0.05 25 Temperature Coefficient Resistance Tolerance (ppm / °C) (%) +600 / −200 ±250 J(±5%) 1.0Ω 10Ω to 9.1Ω to 10MΩ ±250 F(±1%) 10Ω to 10MΩ D(±0.5%) 10Ω 1kΩ to to 910Ω 1MΩ Jumper type : Rmax = 50m Ω / Imax. = 0.5A +500 / −250 1.0Ω J(±5%) 10Ω ±200 10Ω F(±1%) 10Ω ±100 1MΩ ±100 10Ω D(±0.5%) 100Ω ±50 to to to to to to to 9.1Ω 10MΩ 976kΩ 2.2MΩ 2.2MΩ 91Ω 1MΩ Jumper type : Rmax = 50m Ω / Imax. = 1A 1.0Ω ±400 J(±5%) 10Ω ±200 10Ω 10Ω ±100 F(±1%) 1MΩ 10Ω ±100 D(±0.5%) ±50 100Ω to to to to to to to 9.1Ω 10MΩ 976kΩ 10MΩ 10MΩ 91Ω 1MΩ ±200 ±100 0.063 50 0.1 50 Resistance Range Series Operating Temperature Range (°C) E24 −55 to +125 E24 E24,E96 E24 E24 E24,E96 Jumper type : Rmax = 50m Ω / Imax. = 1A ±400 ±200 J(±5%) 1.0Ω 10Ω to 9.1Ω to 10MΩ E24 ±100 F(±1%) 10Ω 10Ω 1MΩ to 976kΩ to 2.2MΩ to 2.2MΩ E24,E96 ±100 ±50 D(±0.5%) 10Ω 100Ω to to 0.125 MCR10 150 ERT 0.1 91Ω 1MΩ E24 1.0Ω 10Ω to 9.1Ω to 10MΩ E24 10Ω 10Ω 1MΩ 10Ω 100Ω to 976kΩ to 2.2MΩ to 2.2MΩ to 91Ω to 1MΩ E24,E96 Jumper type : Rmax = 50m Ω / Imax. = 2A 0.25 200 MCR18 ERT ±400 ±200 J(±5%) ±100 F(±1%) ±100 ±50 0.125 D(±0.5%) −55 to +155 Jumper type : Rmax = 50m Ω / Imax. = 2A MCR25 MCR50 JRT JRT 0.25 200 0.5 200 ±200 ±100 ±100 J(±5%) F(±1%) 1.0Ω 10Ω 10Ω to 9.1Ω to 3.3MΩ to 1MΩ Jumper type : Rmax = 50m Ω / Imax. = 2A ±250 1.0Ω to 9.1Ω J(±5%) 10Ω to 560kΩ ±100 10Ω to 180kΩ F(±1%) ±100 E24 E24,E96 E24 E24,E96 Jumper type : Rmax = 50m Ω / Imax. = 2A MCR100 JRT 1 200 ±250 ±100 ±100 J(±5%) F(±1%) 1.0Ω 10Ω 10Ω to 9.1Ω to 100kΩ to 82kΩ E24 E24,E96 −55 to +125 Jumper type : Rmax = 50m Ω / Imax. =2A ∗Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the product before using or ordering it. ∗Rated voltage is determained from the following. When rated voltage exceeds the limiting element voltage, the limitng element voltage shall be the rated voltage. ∗Rated voltage = Rated power Rasistance www.rohm.com c 2015 ROHM Co., Ltd. All rights reserved. ○ 2/6 2015.02 - Rev.F Datasheet MCR series < Not for Automotive application > Chip Resistor Dimensions and Markings   MCR006 / 01 / 03 L 103 MCR10 / 18 / 25 / 50 / 100 L a a W There are three or four digits used for the calculation number according to IEC code and “R”is used for the decimal point. W a t t b b b (Unit : mm) Part No. Type Code (mm) (inch) L W t a b Marking existence MCR006 YRT 0603 0201 0.6±0.03 0.3±0.03 0.23±0.03 0.15±0.05 0.15±0.05 No No MCR01 MRT 1005 0402 1.0±0.05 0.5±0.05 0.35±0.05 0.2±0.1 0.25 +0.05 −0.1 MCR03 ERT 1608 0603 1.6±0.1 0.8±0.1 0.45±0.1 0.3±0.2 0.3±0.2 Yes ∗ MCR10 ERT 2012 0805 2.0±0.1 1.25±0.1 0.5±0.1 0.35±0.2 0.35±0.2 Yes MCR18 ERT 3216 1206 3.05±0.15 1.55±0.15 0.55±0.1 0.45±0.25 0.35±0.25 Yes 1210 3.2±0.15 2.5±0.15 0.55±0.15 0.5±0.25 0.5±0.25 Yes 2.5±0.15 0.55±0.15 0.6±0.25 0.6±0.25 Yes 3.2±0.15 0.55±0.15 0.6±0.25 0.6±0.25 Yes MCR25 JRT 3225 MCR50 JRT 5025 2010 5.0±0.15 MCR100 JRT 6432 2512 6.3±0.15 Symbol for E96 Series nominal resistance value Marking method of jumper type Jumper type MCR006 / 01 / 25 / 50 / 100 MCR03 / 10 / 18 Marking existence No Yes Marking method of MCR03 The description of markings on the chip resistor are as shown below. ① Marking method (J class): The nominal resistance is expressed in by E-24series 3 digits. The first 2 digits apply to the resistance value and the last one indicates the number of zeros to follow. The R is used as a decimal point. Example：100k= 104 ② Marking method (F/D class): ･For the resistance value contained in E96 series. The nominal resistance is expressed in 3 digits. The first 2 digits is symbol to the resistance value and the last one is symbol to multipliers. 3 Example : 100k= 01d (01d100×10 = 100,000= 100k) 1 Example : 3.01k= 47b (47b301×10 = 3010= 3.01k) ･For the resistance value not contained in E96 series and contained in E-24 series. The marking is expressed by E-24 series in 3 digits and one short bar under the last marking letter. Example : 390= 391 Symbol E96 Symbol E96 Symbol E96 Symbol E96 01 100 25 178 49 316 73 562 02 102 26 182 50 324 74 576 03 105 27 187 51 332 75 590 04 107 28 191 52 340 76 604 05 110 29 196 53 348 77 619 06 113 30 200 54 357 78 634 07 115 31 205 55 365 79 649 08 118 32 210 56 374 80 665 09 121 33 215 57 383 81 681 10 124 34 221 58 392 82 698 11 127 35 226 59 402 83 715 12 130 36 232 60 412 84 732 13 133 37 237 61 422 85 750 14 137 38 243 62 432 86 768 15 140 39 249 63 442 87 787 16 143 40 255 64 453 88 806 17 147 41 261 65 464 89 825 18 150 42 267 66 475 90 845 19 154 43 274 67 487 91 866 20 158 44 280 68 499 92 887 21 162 45 287 69 511 93 909 22 165 46 294 70 523 94 931 23 169 47 301 71 536 95 953 24 174 48 309 72 549 96 976 Symbol for multipliers Symbol A b C d E F X Y multipliers 100 101 102 103 104 105 10−1 10−2 Land pattern Example (Unit : mm) B D Land C A www.rohm.com c 2015 ROHM Co., Ltd. All rights reserved. ○ 3/6 Dimensions Part No. Type Code A B C D MCR006 YRT 0.3 0.84 0.3 0.27 MCR01 MRT 0.5 1.3 0.5 0.4 MCR03 ERT 1.0 2.0 0.8 0.5 MCR10 ERT 1.2 2.6 1.15 0.7 MCR18 ERT 2.2 4.0 1.5 0.9 MCR25 JRT 2.2 4.0 2.3 0.9 MCR50 JRT 3.8 6.0 2.3 1.1 MCR100 JRT 5.1 8.1 3.0 1.5 2015.02 - Rev.F Datasheet MCR series < Not for Automotive application > Derating Curve When the ambient temperature exceeds 70°C, power dissipation must be adjusted according to the derating curves below.   MCR006 / 100 PERCENT RATED POWER (%) PERCENT RATED POWER (%) 80 60 40 20 0 MCR01 / 03 / 10 / 18 / 25 / 50 100 100 −55 0 70 100 80 60 40 20 0 125 −55 AMBIENT TEMPERATURE (°C) 0 70 100 155 AMBIENT TEMPERATURE (°C) Characteristics Guaranteed Value Resistor Type Jumper Type Test Items Test Conditions Resistance See "Products List" 20°C Variation of resistance with temperature See "Products List" Measurement : +20 / −55 / +20 / +125°C ± (2.0%+0.1Ω) Overload Test voltage is the smaller one of 1 or 2 1 Rated voltage (current) ×2.5, 2s. 2 Maximum overload voltage Max. 50mΩ Rosin·Ethanol : 25% (Weight) Soldering condition : 235±5°C Duration of immersion : 2.0±0.5s A new uniform coating of minimum of 95% of the surface being immersed and no soldering damage. Solderability ± (1.0%+0.05Ω) Resistance to soldering heat Max. 50mΩ No remarkable abnormality on the appearance. Soldering condition : 260±5°C Duration of immersion : 10±1s Rapid change of temperature ± (1.0%+0.05Ω) Max. 50mΩ Test temp. −55°C to +125°C 100cycle (MCR006) −55°C to +125°C 300cycle (MCR01) −55°C to +125°C 5cycle (MCR03 / 10 / 18 / 25 / 50 / 100) Damp heat, steady state ± (3.0%+0.1Ω) Max. 100mΩ 40°C, 93%RH (Relative Humidity) Test time : 1,000h to 1,048h Endurance at 70°C ± (3.0%+0.1Ω) Max. 100mΩ 70°C Rated voltage (current) 1.5h : ON − 0.5h : OFF Test time : 1,000h to 1,048h Endurance ± (3.0%+0.1Ω) Max. 100mΩ 125°C (MCR006 / 25 / 50 / 100) 155°C (MCR01 / 03 / 10 / 18) Test time : 1,000h to 1,048h Resistance to solvent ± (1.0%+0.05Ω) Max. 50mΩ 23±5°C, Immersion cleaning, 5±0.5min Solvent : 2−propanol ± (1.0%+0.05Ω) Max. 50mΩ Bend strength of the end face plating Without mechanical damage such as breaks. Maximum overload voltage ∗Test voltage MCR006 MCR01 MCR03 MCR10 MCR18 MCR025 MCR50 MCR100 50V 100V 100V 200V 400V 400V 400V 400V www.rohm.com c 2015 ROHM Co., Ltd. All rights reserved. ○ 4/6 − Compliance Standard(s) : IEC60115−8 JISC 5201−8 2015.02 - Rev.F Datasheet MCR series < Not for Automotive application > Tape Dimensions (Unit : mm)  Paper Tape P0 P2 Part No. Type Code W F E A0 B0 MCR006 YRT 8.0±0.2 3.5±0.05 1.75±0.1 0.38±0.03 0.68±0.03 MCR01 MRT 8.0±0.3 3.5±0.05 1.75±0.1 0.7±0.1 1.2±0.1 MCR03 ERT 8.0±0.3 3.5±0.05 1.75±0.1 1.0±0.1 1.8±0.1 MCR10 ERT 8.0±0.3 3.5±0.05 1.75±0.1 1.55±0.1 2.3±0.1 MCR18 ERT 8.0±0.3 3.5±0.05 1.75±0.1 1.9±0.2 3.5±0.2 MCR25 JRT 8.0±0.2 3.5±0.05 1.75±0.1 2.8±0.2 3.5±0.2 Part No. Type Code D0 P0 P1 P2 T2 MCR006 YRT +0.1 φ1.5 0 4.0±0.1 2.0±0.05 2.0±0.05 Max 0.5 MCR01 MRT φ1.5 +0.1 0 4.0±0.1 2.0±0.1 2.0±0.05 Max 1.1 MCR03 ERT φ1.5 +0.1 0 4.0±0.1 4.0±0.1 2.0±0.05 Max 1.1 MCR10 ERT φ1.5 +0.1 0 4.0±0.1 4.0±0.1 2.0±0.05 Max 1.1 MCR18 ERT φ1.5 +0.1 0 4.0±0.1 4.0±0.1 2.0±0.05 Max 1.1 MCR25 JRT φ1.5 +0.1 0 4.0±0.05 4.0±0.1 2.0±0.05 Max 1.1 Part No. Type Code W F E A0 B0 MCR25 JRT 8.0±0.3 3.5±0.05 1.75±0.1 3.0±0.1 3.5±0.1 MCR50 JRT 12±0.3 5.5±0.05 1.75±0.1 3.4±0.2 5.6±0.2 MCR100 JRT 12±0.3 5.5±0.05 1.75±0.1 3.5±0.2 6.7±0.2 Part No. Type Code D0 P0 P1 P2 T2 MCR25 JRT φ1.5 +0.1 0 4.0±0.1 4.0±0.1 2.0±0.05 Max 1.1 MCR50 JRT φ1.5 +0.1 0 4.0±0.1 4.0±0.1 2.0±0.05 Max 1.1 MCR100 JRT φ1.5 +0.1 0 4.0±0.1 4.0±0.1 2.0±0.05 Max 1.1 P1 φD0 E F W B0 A0 Top tape Base paper (Bottom tape) Components Cavity T2  Embossed Tape (Unit : mm) P2 φD B0 W F E 0 P0 A0 P1 T2 www.rohm.com c 2015 ROHM Co., Ltd. All rights reserved. ○ 5/6 2015.02 - Rev.F Datasheet MCR series < Not for Automotive application > 02 04 06 08 06 D 04 B 02 A 08 Reel Dimensions C Label ACCORDING TO EIAJ ET-7200B (Unit : mm) Part No. Type Code MCR006 YRT MCR01 MRT MCR03 ERT MCR10 ERT MCR18 ERT MCR25 JRT MCR50 JRT MCR100 JRT www.rohm.com c 2015 ROHM Co., Ltd. All rights reserved. ○ A B 0 φ180 −1.5 +1.0 φ60 0 C 9 +1.0 0 13 6/6 D φ13±0.2 +1.0 0 2015.02 - Rev.F Notice Notes 1) The information contained herein is subject to change without notice. 2) Before you use our Products, please contact our sales representative and verify the latest specifications : 3) Although ROHM is continuously working to improve product reliability and quality, semiconductors can break down and malfunction due to various factors. Therefore, in order to prevent personal injury or fire arising from failure, please take safety measures such as complying with the derating characteristics, implementing redundant and fire prevention designs, and utilizing backups and fail-safe procedures. ROHM shall have no responsibility for any damages arising out of the use of our Poducts beyond the rating specified by ROHM. 4) Examples of application circuits, circuit constants and any other information contained herein are provided only to illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. 5) The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM or any other parties. ROHM shall have no responsibility whatsoever for any dispute arising out of the use of such technical information. 6) The Products are intended for use in general electronic equipment (i.e. AV/OA devices, communication, consumer systems, gaming/entertainment sets) as well as the applications indicated in this document. 7) The Products specified in this document are not designed to be radiation tolerant. 8) For use of our Products in applications requiring a high degree of reliability (as exemplified below), please contact and consult with a ROHM representative : transportation equipment (i.e. cars, ships, trains), primary communication equipment, traffic lights, fire/crime prevention, safety equipment, medical systems, servers, solar cells, and power transmission systems. 9) Do not use our Products in applications requiring extremely high reliability, such as aerospace equipment, nuclear power control systems, and submarine repeaters. 10) ROHM shall have no responsibility for any damages or injury arising from non-compliance with the recommended usage conditions and specifications contained herein. 11) ROHM has used reasonable care to ensur the accuracy of the information contained in this document. However, ROHM does not warrants that such information is error-free, and ROHM shall have no responsibility for any damages arising from any inaccuracy or misprint of such information. 12) Please use the Products in accordance with any applicable environmental laws and regulations, such as the RoHS Directive. For more details, including RoHS compatibility, please contact a ROHM sales office. ROHM shall have no responsibility for any damages or losses resulting non-compliance with any applicable laws or regulations. 13) When providing our Products and technologies contained in this document to other countries, you must abide by the procedures and provisions stipulated in all applicable export laws and regulations, including without limitation the US Export Administration Regulations and the Foreign Exchange and Foreign Trade Act. 14) This document, in part or in whole, may not be reprinted or reproduced without prior consent of ROHM. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2015 ROHM Co., Ltd. All rights reserved. R1102A Datasheet MCR03ERTF - Web Page Part Number Package Unit Quantity Minimum Package Quantity Packing Type Constitution Materials List RoHS MCR03ERTF 5000 5000 Taping inquiry Yes