MCR10EZPF1004

Thick Film Chip Resistors MCR Series Datasheet Features 1) Full line up from ultra small size (01005) to 2512 with jumper type. 2) High reliability metal glazed thick film. 3) ROHM resistors have obtained ISO9001/ISO/TS16949 certification. Size Part No. MCR004 (mm) (inch) 0402 01005 Packing Specification Type Code Quantity / Reel Automotive Grade Available （AEC-Q200） YZP 15,000 MCR006 0603 0201 YLP MCR01 1005 0402 MZP MCR03 1608 0603 MCR10 2012 0805 MCR18 3216 1206 MCR25 3225 1210 MCR50 5025 2010 MCR100 6432 2512 Paper tape (2mm pitch) 10,000 Paper tape (4mm pitch) EZP 5,000 Yes Embossed tape (4mm pitch) JZH 4,000 Part Number Description M C R 0 0 4 Part No. Size (mm [inch]) MCR 004 (0402 [01005]) 006 (0603 [0201]) 01 (1005 [0402]) 03 (1608 [0603]) 10 (2012 [0805]) 18 (3216 [1206]) 25 (3225 [1210]) 50 (5025 [2010]) 100 (6432 [2512]) (Micro chip resistors) www.rohm.com c 2015 ROHM Co., Ltd. All rights reserved. ○ Y Z P Type Code J 1 0 0 Resistance Tolerance Nominal Resistance D ( ±0.5% ) F ( ±1% ) FX ( ±1% ) ∗Only MCR03EZP J ( ±5% ) (Including jumper type) Resistance code, 3 or 4 digits. 000 denotes jumper type. Resistance tolerance D,F J Resistance code : : 4 digits 3 digits Ex.) 1Ω = 1R0 ( ±5% ) 9.1 Ω = 9R1 ( ±5% ) 10 Ω = 10R0 ( ±0.5%,±1% ) 100 ( ±5% ) 2.2M Ω = 2204 ( ±1% ) 225 ( ±5% ) 1/6 2015.10 - Rev.I Datasheet MCR series Products List Part No. Type Code Rated Power Limiting Element (70°C) Voltage (W) MCR004 YZP 0.031 Temperature Coefficient Resistance Tolerance (V) (ppm / °C) (%) 15 +600 / −200 ±300 ±250 ±300 ±250 J(±5%) F(±1%) Resistance Range 1.0Ω 10Ω 100Ω 10Ω 100Ω to to to to to 9.1Ω 91Ω 3MΩ 91Ω 3MΩ to to to to to 9.1Ω 10MΩ 10MΩ 910Ω 1MΩ Series Operating Temperature Range (°C) E24 E24,E96 −55 to +125 Jumper type : Rmax = 50m Ω / Imax. = 0.5A MCR006 YLP 0.05 25 +600 / −200 ±250 ±250 ±200 ±100 J(±5%) F(±1%) D(±0.5%) 1.0Ω 10Ω 10Ω 10Ω 1kΩ E24 E24,E96 Jumper type : Rmax = 50m Ω / Imax. = 0.5A MCR01 MCR03 MZP EZP 0.063 0.1 50 50 0.125 MCR10 150 EZP 0.1 +500 / −250 ±200 ±100 ±100 ±50 J(±5%) F(±1%) D(±0.5%) 1.0Ω 10Ω 10Ω 10Ω 100Ω 9.1Ω to to 10MΩ to 2.2MΩ 91Ω to 1MΩ to Jumper type : Rmax = 50m Ω / Imax. = 1A ±400 1.0Ω J(±5%) 10Ω ±200 FX(±1%) 10Ω ±100 10Ω ±100 D(±0.5%) 100Ω ±50 to to to to to Jumper type : Rmax = 50m Ω / Imax. = 1A ±400 1.0Ω J(±5%) ±200 10Ω ±100 10Ω F(±1%) ±100 10Ω D(±0.5%) ±50 100Ω 9.1Ω to to 10MΩ to 2.2MΩ 91Ω to 1MΩ to 9.1Ω 10MΩ 10MΩ 91Ω 1MΩ E24 E24,E96 E24 E24,E96 E24 E24,E96 −55 to +155 Jumper type : Rmax = 50m Ω / Imax. = 2A 0.25 MCR18 200 EZP 0.125 ±400 ±200 ±100 ±100 ±50 J(±5%) F(±1%) D(±0.5%) 1.0Ω 10Ω 10Ω 10Ω 100Ω 9.1Ω to to 10MΩ to 2.2MΩ to 91Ω to 1MΩ E24 E24,E96 Jumper type : Rmax = 50m Ω / Imax. = 2A 500±350 MCR25 JZH 0.25 200 ±500 J(±5%) ±200 ±100 MCR50 MCR100 JZH JZH 0.5 1 200 200 F(±1%) 1.0Ω to 2.0Ω 2.2Ω to 5.1Ω 5.6Ω to 3.3MΩ 10Ω to 1MΩ Jumper type : Rmax = 50m Ω / Imax. = 2A 1.0Ω 500±350 2.2Ω ±500 J(±5%) 10Ω ±200 360kΩ ±350 10Ω ±100 F(±1%) 2.0Ω to 9.1Ω to to 330kΩ to 560kΩ to 180kΩ Jumper type : Rmax = 50m Ω / Imax. = 3A 1.0Ω 500±350 2.2Ω ±500 J(±5%) 10Ω ±350 24Ω ±200 10Ω ±100 F(±1%) 2.0Ω to 9.1Ω to 22Ω to to 100kΩ to 82kΩ E24 E24,E96 E24 E24,E96 E24 −55 to +125 E24,E96 Jumper type : Rmax = 50m Ω / Imax. = 4A ∗Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the product before using or ordering it. ∗Rated voltage is determained from the following. When rated voltage exceeds the limiting element voltage, the limitng element voltage shall be the rated voltage. Rated power Rasistance ∗Rated voltage = ∗E24 : Standard products, E96 : Custom products www.rohm.com c 2015 ROHM Co., Ltd. All rights reserved. ○ 2/6 2015.10 - Rev.I Datasheet MCR series Chip Resistor Dimensions and Markings   MCR004 / 006 / 01 / 03 L 103 MCR10 / 18 / 25 / 50 / 100 L a a W W a There are three or four digits used for the calculation number according to IEC code and “R”is used for the decimal point. t t b b b (Unit : mm) Part No. Type Code (mm) (inch) L W t a b Marking existence MCR004 YZP 0402 01005 0.4±0.02 0.2±0.02 0.13±0.02 0.1±0.03 0.1±0.03 No MCR006 YLP 0603 0201 0.6±0.03 0.3±0.03 0.23±0.03 0.1±0.05 0.15±0.05 No No MCR01 MZP 1005 0402 1.0±0.05 0.5±0.05 0.35±0.05 0.2±0.1 +0.05 0.25 −0.1 MCR03 EZP 1608 0603 1.6±0.1 0.8±0.1 0.45±0.1 0.3±0.2 0.3±0.2 Yes ∗ MCR10 EZP 2012 0805 2.0±0.1 1.25±0.1 0.55±0.1 0.4±0.2 0.4±0.2 Yes MCR18 EZP 3216 1206 3.2±0.15 1.6±0.15 0.55±0.1 0.5±0.25 0.5±0.25 Yes MCR25 JZH 3225 1210 3.2±0.15 2.5±0.15 0.55±0.15 0.5±0.25 0.5±0.25 Yes MCR50 JZH 5025 2010 5.0±0.15 2.5±0.15 0.55±0.15 0.6±0.25 0.6±0.25 Yes MCR100 JZH 6432 2512 6.3±0.15 3.2±0.15 0.55±0.15 0.6±0.25 0.6±0.25 Yes Marking method of jumper type Jumper type Marking existence MCR004 / 006 / 01 / 25 / 50 / 100 No MCR03 / 10 / 18 Yes Marking method of MCR25/50/100 Blueglass over coat is used for the jumper type. There is no marking on the jumper type. Marking method of MCR03 For MCR03 series resistors, the printing process restricts the marking to three digits/characters. Consequently, 1% tolerance resistors with values from the E24 series will be marked the same as 5% resistors with the same value, but 1% tolerance resistors with values from the E96 series will not be marked. Examples: MCR03EZPJ243 MCR03EZPFX2402 MCR03EZPFX2432 (5% tolerance, E24 / 24 k  ) (1% tolerance, E24 / 24 k  ) (1% tolerance, E96 / 24.3 k  ) Marking = 243 Marking = 243 No Marking MCR18EZPJ243 MCR18EZPF2402 MCR18EZPF2432 (5% tolerance, E24 / 24 k  ) (1% tolerance, E24 / 24 k  ) (1% tolerance, E96 / 24.3 k  ) Marking = 243 Marking = 2402 Marking = 2432 (Unit : mm) Land pattern Example Dimensions Part No. Type Code A B C D MCR004 YZP 0.2 0.4 0.16 0.1 MCR006 YLP 0.3 0.84 0.3 0.27 MCR01 MZP 0.5 1.3 0.5 0.4 MCR03 EZP 1.0 2.0 0.8 0.5 MCR10 EZP 1.2 2.6 1.15 0.7 MCR18 EZP 2.2 4.0 1.5 0.9 MCR25 JZH 2.2 4.0 2.3 0.9 MCR50 JZH 3.8 6.0 2.3 1.1 MCR100 JZH 5.1 8.1 3.0 1.5 B D Land C A www.rohm.com c 2015 ROHM Co., Ltd. All rights reserved. ○ 3/6 2015.10 - Rev.I Datasheet MCR series Derating Curve When the ambient temperature exceeds 70°C, power dissipation must be adjusted according to the derating curves below.   MCR004 / 006 / 100 PERCENT RATED POWER (%) PERCENT RATED POWER (%) 80 60 40 20 0 MCR01 / 03 / 10 / 18 / 25 / 50 100 100 −55 0 70 100 80 60 40 20 0 125 −55 0 AMBIENT TEMPERATURE (°C) 70 100 155 AMBIENT TEMPERATURE (°C) Characteristics Guaranteed Value Resistor Type Jumper Type Test Items Test Conditions Resistance See "Products List" 20°C Variation of resistance with temperature See "Products List" Measurement : +20 / −55 / +20 / +125°C ± (2.0%+0.1Ω) Overload Test voltage is the smaller one of 1 or 2 1 Rated voltage (current) ×2.5, 2s. 2 Maximum overload voltage Max. 50mΩ Rosin·Ethanol : 25% (Weight) Soldering condition : 235±5°C Duration of immersion : 2.0±0.5s A new uniform coating of minimum of 95% of the surface being immersed and no soldering damage. Solderability ± (1.0%+0.05Ω) Resistance to soldering heat Max. 50mΩ No remarkable abnormality on the appearance. Soldering condition : 260±5°C Duration of immersion : 10±1s Rapid change of temperature ± (1.0%+0.05Ω) Max. 50mΩ Test temp. −55°C to +125°C 100cycle (MCR006 / 01 / 03) −55°C to +125°C 5cycle (MCR10 / 18 / 25 / 50 / 100) Damp heat, steady state ± (3.0%+0.1Ω) Max. 100mΩ 40°C, 93%RH (Relative Humidity) Test time : 1,000h to 1,048h Endurance at 70°C ± (3.0%+0.1Ω) Max. 100mΩ 70°C Rated voltage (current) 1.5h : ON − 0.5h : OFF Test time : 1,000h to 1,048h Endurance ± (3.0%+0.1Ω) Max. 100mΩ 125°C (MCR006 / 25 / 50 / 100) 155°C (MCR01 / 03 / 10 / 18) Test time : 1,000h to 1,048h Resistance to solvent ± (1.0%+0.05Ω) Max. 50mΩ 23±5°C, Immersion cleaning, 5±0.5min Solvent : 2−propanol ± (1.0%+0.05Ω) Max. 50mΩ Bend strength of the end face plating − Without mechanical damage such as breaks. Maximum overload voltage (Test voltage) MCR004 MCR006 MCR01 MCR03 MCR10 MCR18 MCR025 MCR50 MCR100 30V 50V 100V 100V 200V 400V 400V 400V 400V www.rohm.com c 2015 ROHM Co., Ltd. All rights reserved. ○ 4/6 Compliance Standard(s) : IEC60115−8 JISC 5201−8 2015.10 - Rev.I Datasheet MCR series Tape Dimensions (Unit : mm)  Paper Tape P0 P2 P1 Part No. Type Code W F E A0 B0 MCR004 YZP 8.0±0.2 3.5±0.05 1.75±0.1 0.24±0.03 0.45±0.03 MCR006 YLP 8.0±0.2 3.5±0.05 1.75±0.1 0.38±0.03 0.68±0.03 MCR01 MZP 8.0±0.3 3.5±0.05 1.75±0.1 0.7±0.1 1.2±0.1 MCR03 EZP 8.0±0.3 3.5±0.05 1.75±0.1 1.1±0.1 1.9±0.1 MCR10 EZP 8.0±0.3 3.5±0.05 1.75±0.1 1.65 +0.2 −0.1 2.4 +0.2 −0.1 MCR18 EZP 8.0±0.3 3.5±0.05 1.75±0.1 1.95 +0.1 −0.05 3.5 +0.15 −0.05 Part No. Type Code D0 P0 P1 P2 T2 MCR004 YZP φ1.5 +0.1 0 4.0±0.1 2.0±0.05 2.0±0.05 Max 0.5 MCR006 YLP φ1.5 +0.1 0 4.0±0.1 2.0±0.05 2.0±0.05 Max 0.5 MCR01 MZP φ1.5 +0.1 0 4.0±0.1 2.0±0.05 2.0±0.05 Max 1.1 MCR03 EZP φ1.5 +0.1 0 4.0±0.1 4.0±0.1 2.0±0.05 Max 1.1 MCR10 EZP φ1.5 +0.1 0 4.0±0.1 4.0±0.1 2.0±0.05 Max 1.1 MCR18 EZP φ1.5 +0.1 0 4.0±0.1 4.0±0.1 2.0±0.05 Max 1.1 Part No. Type Code W F E A0 B0 MCR25 JZH 8.0±0.3 3.5±0.05 1.75±0.1 3.0±0.1 3.5±0.1 MCR50 JZH 12±0.3 5.5±0.05 1.75±0.1 3.4±0.2 5.6±0.2 MCR100 JZH 12±0.3 5.5±0.05 1.75±0.1 3.5±0.2 6.7±0.2 Part No. Type Code D0 P0 P1 P2 T2 MCR25 JZH φ1.5 +0.1 0 4.0±0.1 4.0±0.1 2.0±0.05 Max 1.1 MCR50 JZH φ1.5 +0.1 0 4.0±0.1 4.0±0.1 2.0±0.05 Max 1.1 MCR100 JZH φ1.5 +0.1 0 4.0±0.1 4.0±0.1 2.0±0.05 Max 1.1 φD0 E F W B0 A0 Top tape Base paper (Bottom tape) Components Cavity T2  Embossed Tape (Unit : mm) P2 φD B0 W F E 0 P0 A0 P1 T2 www.rohm.com c 2015 ROHM Co., Ltd. All rights reserved. ○ 5/6 2015.10 - Rev.I Datasheet MCR series Reel Dimensions 02 04 06 A 08 06 D 04 B 2 MCR004 / 006 / 01 / 03 / 10 / 18 / 25 02 A 08 1 MCR004 / 006 / 01 / 03 / 10 / 18 / 25 / 50 / 100 B D C Label C Label ACCORDING TO EIAJ ET-7200B ACCORDING TO EIAJ ET-7200B (RRV) (Unit : mm) Part No. Type Code MCR004 YZP MCR006 YLP MCR01 MZP MCR03 EZP MZP MCR10 EZP MCR18 EZP MCR25 JZH MCR50 JZH MCR100 JZH www.rohm.com c 2015 ROHM Co., Ltd. All rights reserved. ○ A B 0 φ180 −1.5 +1.0 φ60 0 C 9 +1.0 0 13 6/6 D φ13±0.2 +1.0 0 2015.10 - Rev.I Datasheet Notice Precaution on using ROHM Products 1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅢ CLASSⅣ CLASSⅢ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice-PAA-E © 2015 ROHM Co., Ltd. All rights reserved. Rev.001 Datasheet Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign trade act, please consult with ROHM in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the Products with other articles such as components, circuits, systems or external equipment (including software). 3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the Products, subject to the terms and conditions herein. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice-PAA-E © 2015 ROHM Co., Ltd. All rights reserved. Rev.001 Datasheet General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s representative. 3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. Notice – WE © 2015 ROHM Co., Ltd. All rights reserved. Rev.001