MCR18EZHF4702

MCR18 Resistors Thick film rectangular MCR18 (1206 size: 1 / 4W) zFeatures 1) Power rating of 1 / 4W 2) Highly reliable chip resistor Ruthenium oxide dielectric offers superior resistance to the elements. 3) Electrodes not corroded by soldering Thick film makes the electrodes very strong. 4) Leading the world in development and mass production. Since start of production in 1976 (first in the wold), this component has established a solid reputation as a general–purpose chip resistor. 5) ROHM resistors have approved ISO–9001 certification. Design and specifications are subject to change without notice. Carefully check the specification sheet before using or ordering it. zRatings Item Rated power Conditions Specifications Power must be derated according to the power derating curve in Figure 1 when ambient temperature exceeds 70°C. 0.25W (1 / 4W) at 70°C POWER LOAD (%) 100 80 60 40 20 0 −55 0 70 100 155 AMBIENT TEMPERATURE (°C) Fig.1 Rated voltage The voltage rating is calculated by the following equation. If the value obtained exceeds the limiting element voltage, the voltage rating is equal to the maximum operating voltage. E: Rated voltage (V) E= P×R P: Rated power (W) R: Nominal resistance (Ω) Nominal resistance Operating temperature Limiting element voltage 200V See Table 1. −55°C to +155°C Rev.B 1/5 MCR18 Resistors Jumper type Table 1 Max. 50mΩ Resistance Rated current Resistance range (Ω) Resistance tolerance 2A Operating temperature −55°C to +155°C Resistance temperature coefficient (ppm / °C) F (±1%) 10 ≤ R ≤ 2.2M (E24,96) J (±5%) 1.0 ≤ R < 2.2 (E24) 500±350 2.2 ≤ R < 10 (E24) ±500 10 ≤ R ≤ 10M (E24) ±200 ±100 zBefore using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high–level loads), be certain to evaluate the component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that is greater than its rated voltage. zCharacteristics Item Resistance Guaranteed value Resistor type Jumper type J : ±5% F : ±1% Max. 50mΩ Variation of resistance with temperature Overload Solderability Resistance to soldering heat Rapid change of temperature See Table.1 ± (2.0%+0.1Ω) Max. 50mΩ A new uniform coating of minimum of 95% of the surface being immersed and no soldering damage. JIS C 5201-1 4.5 JIS C 5201-1 4.8 Measurement : −55 / +25 / +125°C JIS C 5201-1 4.13 Rated voltage (current) ×2.5, 2s. Maximum overload voltage : 400V JIS C 5201-1 4.17 Rosin·Ethanol (25%WT) Soldering condition : 235±5°C Duration of immersion : 2.0±0.5s. ± (1.0%+0.05Ω) Max. 50mΩ No remarkable abnormality on the appearance. JIS C 5201-1 4.18 Soldering condition : 260±5°C Duration of immersion : 10±1s. ± (1.0%+0.05Ω) Max. 50mΩ JIS C 5201-1 4.19 Test temp. : −55°C to +125°C 5cyc ± (3.0%+0.1Ω) Max. 100mΩ JIS C 5201-1 4.24 40°C, 93%RH Test time : 1,000h to 1,048h ± (3.0%+0.1Ω) Max. 100mΩ JIS C 5201-1 4.25.1 Rated voltage (current), 70°C 1.5h : ON − 0.5h : OFF Test time : 1,000h to 1,048h ± (3.0%+0.1Ω) Max. 100mΩ JIS C 5201-1 4.25.3 155°C Test time : 1,000h to 1,048h ± (1.0%+0.05Ω) Max. 50mΩ JIS C 5201-1 4.29 23±5°C, Immersion cleaning, 5±0.5min. Solvent : 2-propanol Damp heat, steady state Endurance at 70°C Endurance Resistance to solvent Bend strength of the end face plating Test conditions (JIS C 5201-1) Max. 50mΩ ± (1.0%+0.05Ω) Without mechanical damage such as breaks. JIS C 5201-1 4.33 Rev.B 2/5 MCR18 Resistors zExternal dimensions (Unit : mm) 1 0.5±0.25 3 1 Resistive element (Oxide metal thick film) 2 Silver thick film electrode 3 Nickel electrode 4 Sn electrode 5 Alumina substrate 6 Overcoating 4 1.6±0.15 5 0.55±0.1 0.5±0.25 3.2±0.15 Material No. 2 6 zPackaging Reel Taping P0 P2 P2 φD2 E F W 02 04 06 08 06 D 04 B 02 A 08 B2 A2 Heat crimp cover/Tape Thick paper (Underside paper tape) Chip resistor Square punchout hole mount T2 C (Unit: mm) Label EIAJ ET-7200B compliant W 8.0±0.3 (Unit: mm) A φ180 0 −1.5 B φ60 C +1 0 9 +1.0 0 D D2 φ1.5 +0.1 0 F 3.5±0.05 E A2 1.75±0.1 +0.1 1.95 −0.05 B2 3.5 +0.15 −0.05 P2 P2 P2 T2 4.0±0.1 4.0±0.1 2.0±0.05 Max. 1.1 φ13±0.2 Rev.B 3/5 MCR18 Resistors zMakeup of the part number M C R 1 8 Part No. E Z H J Resistance tolerance F J ±1% ±5% J is also used for jumper Nominal resistance Resistance code, 3 or 4 digits. 000 denotes jumper type. Resistance Resistance tolerance code F J : : 4 digits 3 digits Packaging Specifications Code Part No. Code MCR18 EZH Resistance tolerance J(±5%) F(±1%) Packaging specifications Reel Basic ordering unit (pcs) Paper tape (4mm Pitch) φ180mm (7in.) 5,000 Reel (φ180) : JEITA ET-7200B : Standard product zDimensions 3.45 1.80 JIS C 5201-1 4.4.2 SAMPLE SIZE : n=20pcs MICROMETER 3.40 3.35 0.75 JIS C 5201-1 4.4.2 SAMPLE SIZE : n=20pcs MICROMETER 1.75 1.70 THICKNESS (mm) 0.65 WIDTH (mm) LENGTH (mm) 3.30 3.25 3.20 3.15 3.10 JIS C 5201-1 4.4.2 SAMPLE SIZE : n=20pcs MICROMETER 0.70 1.65 0.60 1.60 0.55 1.55 0.50 1.50 0.45 1.45 0.40 3.05 3.00 2.95 0.1 1 1.40 10 100 1k 10k 100k 1M 10M 0.1 1 10 100 1k 10k 100k 1M 10M 0.35 0.1 1 RESISTANCE (Ω) RESISTANCE (Ω) RESISTANCE (Ω) Fig.3 Dimensions (width) Fig.2 Dimensions (length) 10 100 1k 10k 100k 1M 10M Fig.4 Dimensions (thickness) JIS C 5201-1 4.5 SAMPLE SIZE : n=20pcs 20°C 65%RH DC RESISTANCE (%) 6.0 4.0 2.0 0.0 −2.0 −4.0 −6.0 −8.0 0.1 1 10 100 1k 10k 100k 1M 10M RESISTANCE (Ω) Fig.5 Resistance 900 4.0 JIS C 5201-1 4.8 SAMPLE SIZE : n=10pcs 25°C / −55°C 25°C / 125°C 700 500 2.0 300 100 −100 1.0 0.0 −1.0 −300 −2.0 −500 −3.0 −700 −900 JIS C 5201-1 4.13 SAMPLE SIZE : n=10pcs RATED VOLTAGE×2.5TIMES : 2s MAXIMUM OVERLOAD VOLTAGE : 400V 3.0 ∆R/R (%) 8.0 TEMPERATURE COEFFICIENT (ppm/°C) zElectrical characteristics 0.1 1 10 100 1k 10k 100k 1M 10M RESISTANCE (Ω) Fig.6 Variation resistance with temperature −4.0 0.1 1 10 100 1k 10k 100k1M 10M RESISTANCE (Ω) Fig.7 Overload Rev.B 4/5 MCR18 Resistors 2.0 1.5 1.0 0.5 0.5 ∆R/R (%) 1.0 0 −0.5 0.0 −0.5 −1.0 −1.0 −1.5 −1.5 −2.0 −2.0 0.1 1 JIS C 5201-1 4.19 SAMPLE SIZE : n=10pcs −55°C / 125°C 5cyc 10 100 1k 10k 100k 1M 10M 0.1 1 −2.0 2.0 1.0 1.0 0.5 0 −1.0 0.0 −0.5 −3.0 −3.0 −1.5 −4.0 −4.0 10 100 1k 10k 100k 1M 10M RESISTANCE (Ω) Fig.11 Endurance (at 70°C) 10 100 1k 10k 100k 1M 10M 0.1 1 10 100 1k 10k 100k 1M 10M RESISTANCE (Ω) Fig.12 Endurance JIS C 5201-1 4.29 SAMPLE SIZE : n=10pcs IPA, 5min. 1.5 −1.0 1 1 2.0 −2.0 0.1 0.1 RESISTANCE (Ω) ∆R/R (%) −1.0 −2.0 Fig.10 Damp heat, steady state JIS C 5201-1 4.25.3 SAMPLE SIZE : n=10pcs 155°C WITH NO LOAD 1,000h 3.0 RESISTANCE CHANGE (%) RESISTANCE CHANGE (%) 0 −1.0 −4.0 10 100 1k 10k 100k 1M 10M 4.0 1.0 0 Fig.9 Rapid change of temperature 4.0 2.0 1.0 RESISTANCE (Ω) Fig.8 Resistance to soldering heat 3.0 2.0 −3.0 RESISTANCE (Ω) JIS C 5201-1 4.25.1 SAMPLE SIZE : n=10pcs 70°C 1,000h OVERLOAD : THE RATED VOLTAGE JIS C 5201-1 4.24 SAMPLE SIZE : n=10pcs 40°C 93%RH WITH NO LOAD 1,000h 3.0 RESISTANCE CHANGE (%) 1.5 RESISTANCE CHANGE (%) 4.0 2.0 JIS C 5201-1 4.18 SAMPLE SIZE : n=10pcs SOLDERING CONDITION : 260°C 10s −2.0 0.1 1 10 100 1k 10k 100k 1M 10M RESISTANCE (Ω) Fig.13 Resistance to solvents 2.0 JIS C 5201-1 4.33 SAMPLE SIZE : n=10pcs ENDURANCE WITH 90mm WIDTH RESISTANCE CHANGE (%) 1.5 1.0 0.5 0 −0.5 −1.0 −1.5 −2.0 0.1 1 10 100 1k 10k 100k 1M 10M RESISTANCE (Ω) Fig.14 Bend strength of the end face plating Rev.B 5/5 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1