MNR12E0ABJ330

MNR12 Resistors Chip resistor networks MNR12 (1608×2 size) !Features 1) Convex electrodes Easy to check the fillet after soldering is finished. 2) Small, light, rectangular 2-chip network Area ratio is 65% smaller than that of MNR32, while weight ratio has been cut 75%. 3) High-density mounting Can be mounted even more densely than two 1608 chips (MCR03), and mounting costs are lower. 4) Compatible with a wide range of mounting equipment. Squared corners make it excellent for mounting using image recognition devices. 5) ROHM resistors have approved ISO-9001 certification. Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the product before using or ordering it. !Ratings Item Rated power Conditions Specifications Power must be derated according to the power derating curve in Figure 1 when ambient temperature exceeds 70°C. 0.063W (1 / 16W) at 70°C 100 POWER LOAD (%) 80 60 40 20 0 −55 0 70 100 125 AMBIENT TEMPERATURE (°C) Fig.1 Rated voltage The voltage rating is calculated by the following equation. If the value obtained exceeds the limiting element voltage, the voltage rating is equal to the maximum operating voltage. E: Rated voltage (V) E= P×R P: Rated power (W) R: Nominal resistance (Ω) Nominal resistance Operating temperature Limiting element voltage 50V See Table 1. −55°C~+125°C MNR12 Resistors Table 1 Jumper type Max. 50mΩ Resistance Rated current Resistance tolerance 1A J (±5%) Operating temperature −55°C~+125°C Resistance range (Ω) 10≤R≤1M (E24) Resistance temperature coefficient (ppm / °C) ±200 •Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that is greater than its rated voltage. !Characteristics Item Resistance Guaranteed value Resistor type Jumper type J : ±5% Max. 50mΩ Variation of resistance with temperature Overload Solderability Resistance to soldering heat Rapid change of temperature See Table.1 ± (2.0%+0.1Ω) Max. 50mΩ A new uniform coating of minimum of 95% of the surface being immersed and no soldering damage. JIS C 5201-1 4.5 JIS C 5201-1 4.8 Measurement : −55 / +25 / +125°C JIS C 5201-1 4.13 Rated voltage (current) ×2.5, 2s. Limiting Element Voltage×2 : 100V JIS C 5201-1 4.17 Rosin·Ethanol (25%WT) Soldering condition : 235±5°C Duration of immersion : 2.0±0.5s. ± (1.0%+0.05Ω) Max. 50mΩ No remarkable abnormality on the appearance. JIS C 5201-1 4.18 Soldering condition : 260±5°C Duration of immersion : 10±1s. ± (1.0%+0.05Ω) Max. 50mΩ JIS C 5201-1 4.19 Test temp. : −55°C~+125°C 5cyc ± (3.0%+0.1Ω) Max. 50mΩ JIS C 5201-1 4.24 40°C, 93%RH Test time : 1,000h~1,048h ± (3.0%+0.1Ω) Max. 50mΩ JIS C 5201-1 4.25.1 Rated voltage (current), 70°C 1.5h : ON − 0.5h : OFF Test time : 1,000h~1,048h ± (3.0%+0.1Ω) Max. 50mΩ JIS C 5201-1 4.25.3 125°C Test time : 1,000h~1,048h ± (1.0%+0.05Ω) Max. 50mΩ JIS C 5201-1 4.29 23±5°C, Immersion cleaning, 5±0.5min. Solvent : 2-propanol Damp heat, steady state Endurance at 70°C Endurance Resistance to solvent Bend strength of the end face plating Test conditions (JIS C 5201-1) Max. 50mΩ ± (1.0%+0.05Ω) Without mechanical damage such as breaks. JIS C 5201-1 4.33 MNR12 Resistors !External dimensions (Units : mm) 1.6±0.1 ∗∗0.8 No. 1 6 Cross section A-A' B ∗Marking Material 1 Thick dielectric glaze of ruthenium (only silver used for jumper) 2 Thick film of silver for primary electrode 3 Nickel-coated secondary electrode 4 External electrode coated with Sn/Pb or Sn 5 Alumina substrate 6 Overcoating A' 0.25±0.15 0.3±0.2 1.6±0.1 A 102 102 5 6 Cross section B-B' 1 5 2 B' 0.4±0.15 3 4 0.5±0.1 0.35±0.1 0.6±0.15 ∗ Making may change to the one-character type. ∗∗ Pitch of the upper electrode. !Equivalent circuit R1 R2 R1 = R2 !Packaging Taping Reel P0 P2 φD0 P1 E F W 02 04 06 08 06 D 04 B 02 A 08 B0 A0 Heat crimp cover / Tape Chip network Thick paper (Underside paper tape) resistor Square punchout hole mount T2 C (Units : mm) Label EIAJ ET-7200A compliant (Units : mm) A B C D 0 φ180 −3 +1 φ60 0 +1.0 9 0 φ13±0.2 W F E A0 B0 8.0±0.3 3.5±0.05 1.75±0.1 1.8±0.1 1.8±0.1 D0 φ1.5 +0.1 0 P0 P1 P2 T2 4.0±0.1 4.0±0.1 2.0±0.05 Max. 1.1 MNR12 Resistors !Product designation Part No. Packaging / Processing specifications Code E0 Part No. MNR12 / 14 Packaging Taping Circuit configuration code Package style Paper tape with reel Resistance tolerance AB MNR04 / 12 / 14 / 32 / 34 J Nominal resistance ±5% 3-digit IEC coding system JIS C 5201-1 4.5 SAMPLE SIZE : n=40pcs 20°C 65%RH 5.0 3.0 2.0 1.0 0 −1.0 −2.0 −3.0 −4.0 −5.0 −6.0 10 100 1k 10k 100k 1M 300 2.0 100 0 −100 0 −2.0 −200 −4.0 −300 −400 10 100 1k 10k 100k −6.0 1M 100 1k 10k 100k RESISTANCE (Ω) RESISTANCE (Ω) Fig.2 Resistance Fig.3 Variation resistance with temperature Fig.4 Overload 3.0 JIS C 5201-1 4.18 SAMPLE SIZE : n=20pcs SOLDERING CONDITION : 260°C 10s ∆R/R (%) 2.0 0 0 −1.0 −1.0 −2.0 −2.0 −2.0 −4.0 100 1k 10k 100k 1M RESISTANCE (Ω) Fig.5 Resistance to soldering heat −3.0 JIS C 5201-1 4.24 SAMPLE SIZE : n=20pcs 40°C 93%RH WITH NO LOAD 1000h 4.0 1.0 0 1M 6.0 JIS C 5201-1 4.19 SAMPLE SIZE : n=20pcs −55°C / 125°C 5cyc 2.0 1.0 10 10 RESISTANCE (Ω) 2.0 −3.0 JIS C 5201-1 4.13 SAMPLE SIZE : n=20pcs RATED VOLTAGE × 2.5TIMES 2s LIMITING ELEMENT VOLTAGE×2 : 100V 4.0 200 3.0 ∆R/R (%) 6.0 JIS C 5201-1 4.8 SAMPLE SIZE : n=20pcs 25°C / −55°C 25°C / 125°C ∆R/R (%) DC RESISTANCE (%) 4.0 400 ∆R/R (%) 6.0 TEMPERATURE COEFFICIENT (ppm / °C) !Electrical characteristics 10 100 1k 10k 100k RESISTANCE (Ω) Fig.6 Rapid change of temperature 1M −6.0 10 100 1k 10k 100k 1M RESISTANCE (Ω) Fig.7 Damp heat, steady state MNR12 Resistors 6.0 4.0 JIS C 5201-1 4.25.3 SAMPLE SIZE : n=20pcs 125°C WITH NO LOAD 1,000h 4.0 1.0 ∆R/R (%) ∆R/R (%) 0 JIS C 5201-1 4.29 SAMPLE SIZE : n=20pcs IPA, 5min. 1.5 2.0 2.0 ∆R/R (%) 2.0 6.0 JIS C 5201-1 4.25.1 SAMPLE SIZE : n=20pcs 70°C 1,000h OVERLOAD : THE RATED VOLTAGE 0 −2.0 −2.0 −4.0 −4.0 −6.0 −6.0 0.5 0 −0.5 −1.0 10 100 1k 10k 100k 1M −1.5 10 100 1k 10k 100k 1M −2.0 10 100 1k 10k 100k 1M RESISTANCE (Ω) RESISTANCE (Ω) RESISTANCE (Ω) Fig.8 Endurance at 70°C Fig.9 Endurance Fig.10 Resistance to solvents