MNR14E0ABJ2R2

MNR14 Resistors Chip resistor networks MNR14 (0603×4 size) zFeatures 1) Convex electrodes Easy to check the fillet after soldering is finished. 2) Small, light, rectangular 4-chip network Area ratio is 65% smaller than that of MNR34, while weight ratio has been cut 75%. 3) High-density mounting Can be mounted even more densely than four 0603 chips (MCR03), and mounting costs are lower. 4) Compatible with a wide range of mounting equipment. Squared corners make it excellent for mounting using image recognition machines. 5) ROHM resistors have approved ISO-9001 certification. Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the product before using or ordering it. zRatings Item Rated power Conditions Specifications Power must be derated according to the power derating curve in Figure 1 when ambient temperature exceeds 70°C. 0.063W (1 / 16W) at 70°C POWER LOAD (%) 100 80 60 40 20 0 −55 0 70 100 125 AMBIENT TEMPERATURE (°C) Fig.1 Rated voltage The voltage rating is calculated by the following equation. If the value obtained exceeds the limiting element voltage, the voltage rating is equal to the maximum operating voltage. E: Rated voltage (V) E= P×R P: Rated power (W) R: Nominal resistance (Ω) Nominal resistance Operating temperature Limiting element voltage 50V See Table 1. −55°C to +125°C Rev.A 1/5 MNR14 Resistors Jumper type Table 1 Max. 50mΩ Resistance Rated current Resistance range (Ω) Resistance tolerance 1A Operating temperature −55°C to +125°C J (±5%) Resistance temperature coefficient (ppm / °C) 2.2≤R≤10 (E6) ±500 10≤R≤1M (E24) ±200 •Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that is greater than its rated voltage. zCharacteristics Item Resistance Guaranteed value Resistor type Jumper type J : ±5% Max. 50mΩ Variation of resistance with temperature Overload Solderability Resistance to soldering heat Rapid change of temperature See Table.1 ± (2.0%+0.1Ω) Max. 50mΩ A new uniform coating of minimum of 95% of the surface being immersed and no soldering damage. JIS C 5201-1 4.5 JIS C 5201-1 4.8 Measurement : −55 / +25 / +125°C JIS C 5201-1 4.13 Rated voltage (current) ×2.5, 2s. Maximum Overload Voltage : 100V JIS C 5201-1 4.17 Rosin·Ethanol (25%WT) Soldering condition : 235±5°C Duration of immersion : 2.0±0.5s. ± (1.0%+0.05Ω) Max. 50mΩ No remarkable abnormality on the appearance. JIS C 5201-1 4.18 Soldering condition : 260±5°C Duration of immersion : 10±1s. ± (1.0%+0.05Ω) Max. 50mΩ JIS C 5201-1 4.19 Test temp. : −55°C to +125°C 5cyc ± (3.0%+0.1Ω) Max. 100mΩ JIS C 5201-1 4.24 40°C, 93%RH Test time : 1,000h to 1,048h ± (3.0%+0.1Ω) Max. 100mΩ JIS C 5201-1 4.25.1 Rated voltage (current), 70°C 1.5h : ON − 0.5h : OFF Test time : 1,000h to 1,048h ± (3.0%+0.1Ω) Max. 100mΩ JIS C 5201-1 4.25.3 125°C Test time : 1,000h to 1,048h ± (1.0%+0.05Ω) Max. 50mΩ JIS C 5201-1 4.29 23±5°C, Immersion cleaning, 5±0.5min. Solvent : 2-propanol Damp heat, steady state Endurance at 70°C Endurance Resistance to solvent Bend strength of the end face plating Test conditions (JIS C 5201-1) Max. 50mΩ ± (1.0%+0.05Ω) Without mechanical damage such as breaks. JIS C 5201-1 4.33 Rev.A 2/5 MNR14 Resistors zExternal dimensions (Unit : mm) 3.2±0.1 A' 0.25±0.15 0 1 ∗∗0.8 0.3±0.2 0 1 ∗∗0.8 Material 1.6±0.1 0 1 2 2 0 A a : 0.6±0.15 b : 0.4±0.15 B 1 2 b 2 a ∗Marking 1 Thick dielectric glaze of oxide metal (only silver used for jumper) 2 Thick film of silver for electrode 3 Nickel-coated electrode 4 External electrode coated with Sn 5 Alumina substrate 6 Overcoating ∗∗0.8 B' 0.5±0.1 2 6 Cross section A-A' 3 4 1 5 1 6 Cross section B-B' ∗ Marking may change to the one-character type. ∗∗ Pitch of the upper electrode. 5 zEquivalent circuit R1 R2 R3 R4 R1=R2=R3=R4 zPackaging Reel Taping P0 P2 φD0 P1 E F W 02 04 06 08 06 D 04 B 02 A 08 B0 A0 Heat crimp cover / Tape Chip network Thick paper (Underside paper tape) resistors Square punchout hole mount T2 C (Unit : mm) Label EIAJ ET-7200B compliant (Unit : mm) A B C D 0 φ180 −3 φ60 +1 0 9 +1.0 0 φ13±0.2 W F E A0 B0 8.0±0.3 3.5±0.05 1.75±0.1 1.8±0.1 3.4±0.1 D0 P0 P1 P2 T2 φ1.5 +0.1 0 4.0±0.1 4.0±0.1 2.0±0.05 Max. 1.1 Rev.A 3/5 MNR14 Resistors zProduct designation M N R 1 4 E 0 A B Part No. J Resistance tolerance Nominal resistance J ±5% J is also used for jumper Resistance code,3 digits, 000 denotes Jumper type. Packaging Specifications Code Part No. Code MNR14 E0AB Resistance tolerance J(±5%) Packaging specifications Paper tape (4mm Pitch) Reel Basic ordering unit (pcs) φ180mm (7in.) 5,000 Reel (φ180) : JEITA ET-7200B : Standard product JIS C 5201-1 4.5 SAMPLE SIZE : n=40pcs 20°C 65%RH 5.0 DC RESISTANCE (%) 4.0 3.0 2.0 1.0 0 −1.0 −2.0 −3.0 −4.0 −5.0 −6.0 10 100 1k 10k 100k 1M 400 6.0 JIS C 5201-1 4.8 SAMPLE SIZE : n=20pcs 25°C / −55°C 25°C / 125°C 300 200 2.0 100 0 −100 −2.0 −4.0 −300 −400 10 100 1k 10k 100k −6.0 1M ∆R/R (%) ∆R/R (%) 0 0 −1.0 −2.0 −2.0 −2.0 −4.0 1k 10k 100k 1M RESISTANCE (Ω) Fig.5 Resistance to soldering heat −3.0 1M 2.0 −1.0 100 100k JIS C 5201-1 4.24 SAMPLE SIZE : n=20pcs 40°C 93%RH WITH NO LOAD 1,000h 4.0 1.0 0 10k 6.0 JIS C 5201-1 4.19 SAMPLE SIZE : n=20pcs −55°C / 125°C 5cyc 2.0 1.0 1k Fig.4 Overload 3.0 JIS C 5201-1 4.18 SAMPLE SIZE : n=20pcs SOLDERING CONDITION : 260°C 10S 10 100 RESISTANCE (Ω) Fig.3 Variation resistance with temperature 3.0 −3.0 10 RESISTANCE (Ω) Fig.2 Resistance ∆R/R (%) 0 −200 RESISTANCE (Ω) 2.0 JIS C 5201-1 4.13 SAMPLE SIZE : n=20pcs RATED VOLTAGE×2.5TIMES 2s MAXIMUM OVERLOAD VOLTAGE : 100V 4.0 ∆R/R (%) 6.0 TEMPERATURE COEFICIENT (ppm / °C) zElectrical characteristics 10 100 1k 10k 100k RESISTANCE (Ω) Fig.6 Rapid change of temperature 1M −6.0 10 100 1k 10k 100k 1M RESISTANCE (Ω) Fig.7 Damp heat, steady state Rev.A 4/5 MNR14 Resistors JIS C 5201-1 4.25.1 SAMPLE SIZE : n=20pcs 70°C 1,000h OVERLOAD : THE RATED VOLTAGE 4.0 JIS C 5201-1 4.29 SAMPLE SIZE : n=20pcs IPA, 5min. 1.5 1.0 2.0 ∆R/R (%) 2.0 0 JIS C 5201-1 4.25.3 SAMPLE SIZE : n=20pcs 125°C WITH NO LOAD 1,000h ∆R/R (%) 4.0 ∆R/R (%) 2.0 6.0 6.0 0 −2.0 −2.0 −4.0 −4.0 0.5 0 −0.5 −1.0 −6.0 10 100 1k 10k 100k 1M −6.0 −1.5 10 100 1k 10k 100k 1M −2.0 10 100 1k 10k 100k 1M RESISTANCE (Ω) RESISTANCE (Ω) RESISTANCE (Ω) Fig.8 Endurance at 70°C Fig.9 Endurance Fig.10 Resistance to solvents Rev.A 5/5 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1