MNR18

MNR18 Resistors Chip resistor networks MNR18 (0603×8 size) Features 1) Suitable for damping resistors. 2) Convex electrodes Easy to check the fillet after soldering is finished. 3) High-density mounting Can be mounted even densely than eight 0402 chips (MCR01), and mounting costs are lower. 4) Compatible with a wide range of mounting machines. Squared corners make it excellent for mounting using image recognition machines. 5) ROHM resistors have approved ISO-9001 certification. Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the product before using or ordering it. Ratings Item Rated power Conditions Power must be derated according to the power derating curve in Figure 1 when ambient temperature exceeds 70°C. 100 80 60 40 20 0 Specifications 0.063W (1 / 16W) at 70°C POWER LOAD (%) Power for a Packaging Max 0.25W (1 / 4W) −55 0 70 100 125 AMBIENT TEMPERATURE (°C) Fig.1 Rated voltage The voltage rating is calculated by the following equation. If the value obtained exceeds the limiting element voltage, the voltage rating is equal to the maximum operating voltage. E : Rated voltage (V) P : Rated power (W) R : Nominal resistance (Ω) E= P×R Nominal resistance Operating temperature Limiting element voltage 25V See Table 1. −55°C to +125°C Jumper type Resistance Rated current Max. 50mΩ 1A Power for a Packaging Max 0.25W (1 / 4W) Table 1 Resistance tolerance Resistance range (Ω) Resistance temperature coefficient (ppm / °C) J (±5%) 10≤R≤1M (E24) ±200 Operating temperature −55°C to +125°C ∗Before using components in circuits where they will be exposed to transients such as pulse loads(short-duration, high-level loads), be certain to evaluate the component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that is greater than its rated voltage. Rev.B 1/4 MNR18 Resistors Characteristics Item Resistance Variation of resistance with temperature Overload ± (2.0%+0.1Ω) Guaranteed value Resistor type Jumper type J : ±5% Max. 50mΩ See Table.1 Max. 50mΩ Test conditions (JIS C 5201-1) JIS C 5201-1 4.5 JIS C 5201-1 4.8 Measurement : +25 / +125°C JIS C 5201-1 4.13 Rated voltage (current) ×2.5, 2s. Maximum Overload Voltage : 100V JIS C 5201-1 4.17 Rosin·Ethanol (25%WT) Soldering condition : 235±5°C Duration of immersion : 2.0±0.5s. JIS C 5201-1 4.18 Soldering condition : 260±5°C Duration of immersion : 10±1s. JIS C 5201-1 4.19 Test temp. : −55°C to +125°C 5cyc JIS C 5201-1 4.24 40°C, 93%RH Test time : 1,000h to 1,048h JIS C 5201-1 4.25.1 Rated voltage (current), 70°C 1.5h : ON − 0.5h : OFF Test time : 1,000h to 1,048h JIS C 5201-1 4.25.3 125°C Test time : 1,000h to 1,048h JIS C 5201-1 4.29 23±5°C, Immersion cleaning, 5±0.5min. Solvent : 2-propanol JIS C 5201-1 4.33 Solderability A new uniform coating of minimum of 95% of the surface being immersed and no soldering damage. ± (1.0%+0.05Ω) Max. 50mΩ No remarkable abnormality on the appearance. ± (1.0%+0.05Ω) ± (3.0%+0.1Ω) Max. 50mΩ Max. 100mΩ Resistance to soldering heat Rapid change of temperature Damp heat, steady state ± (3.0%+0.1Ω) Endurance at 70°C ± (3.0%+0.1Ω) Endurance ± (1.0%+0.05Ω) Resistance to solvent Max. 100mΩ Max. 100mΩ Max. 50mΩ Bend strength of the end face plating Max. 50mΩ ± (1.0%+0.05Ω) Without mechanical damage such as breaks. External dimensions (Unit : mm) 3.8±0.1 a a b B a : 0.3±0.1 b : (0.2) c : (0.5) ( ) is reference value. No. 1 Material Resistive element (Oxide metal thick film) Silver thick film electrode Nickel electrode Sn electrode Alumina substrate Over-coating (Resin) 0.3±0.2 0.3±0.2 A A' 1.6±0.1 2 3 4 c c 5 B' 0.45±0.1 2 3 4 6 Cross section A−A' 6 1 5 Cross section B−B' 1 6 Maqnification 5 Rev.B 2/4 MNR18 Resistors Equivalent circuit R1 R2 R3 R4 R5 R6 R7 R8 R1 = R2 = R3 = R4 = R5 = R6 = R7 = R8 Packaging Reel Taping P0 P2 P1 φD0 E F B0 08 06 04 02 02 04 06 08 W A B D A0 Heat crimp cover / Tape Chip network Thick paper resistors Square punchout hole (Underside paper tape) mount T2 C Label EIAJ ET-7200B compliant (Unit : mm) W F E A0 B0 (Unit : mm) 8.0±0.3 D0 3.5±0.05 P0 1.75±0.1 P1 1.95±0.15 P2 4.1±0.15 T2 A B C D φ180 0 −1.5 φ60 +1 0 9 +1.0 0 φ13±0.2 φ1.5 +0.1 0 4.0±0.1 4.0±0.1 2.0±0.05 Max. 1.1 Product designation MNR1 8 Part No. E0AP J ±5% J is also used for jumper J Nominal resistance Resistance code,3 digits, 000 denotes Jumper type. Resistance tolerance Packaging Specifications Code Part No. Code Resistance tolerance J(±5%) Packaging specifications Reel Basic ordering unit (pcs) MNR18 E0AP Paper tape (4mm Pitch) φ180mm (7in.) 5,000 Reel (φ180) : JEITA ET-7200B : Standard product Rev.B 3/4 MNR18 Resistors Electrical characteristics TEMPERATURE COEFICIENT (ppm/°C) 6.0 5.0 4.0 DC RESISTANCE (%) 400 300 200 ∆R/R (%) 6.0 JIS C 5201-1 4.5 SAMPLE SIZE : n=24pcs 20°C 65%RH JIS C 5201-1 4.8 SAMPLE SIZE : n=24pcs 25°C / 125°C 5.0 4.0 3.0 2.0 1.0 0 −1.0 −2.0 −3.0 −4.0 −5.0 −6.0 3.0 2.0 1.0 0 −1.0 −2.0 −3.0 −4.0 −5.0 −6.0 10 100 1k 10k 100k 1M JIS C 5201-1 4.13 SAMPLE SIZE : n=24pcs RATED VOLTAGE×2.5TIMES 2S MAXIMUM OVERLOAD VOLTAGE : 50V 100 0 −100 −200 −300 −400 10 100 1k 10k 100k 1M 10 100 1k 10k 100k 1M RESISTANCE (Ω) RESISTANCE (Ω) RESISTANCE (Ω) Fig.2 Resistance Fig.3 Vatiation resistance with temperature Fig.4 Overload 3.0 2.0 1.0 ∆R/R (%) ∆R/R (%) JIS C 5201-1 4.18 SAMPLE SIZE : n=24pcs SOLDERING CONDITION : 260°C 10S 3.0 2.0 1.0 JIS C 5201-1 4.19 SAMPLE SIZE : n=24pcs −55°C / 125°C 5cyc 6.0 5.0 4.0 3.0 2.0 JIS C 5201-1 4.24 SAMPLE SIZE : n=24pcs 40°C 93%RH WITH NO LOAD 1,000h ∆R/R (%) 1.0 0 −1.0 −2.0 −3.0 −4.0 −5.0 −6.0 0 −1.0 −2.0 −3.0 0 −1.0 −2.0 −3.0 10 100 1k 10k 100k 1M 10 100 1k 10k 100k 1M 10 100 1k 10k 100k 1M RESISTANCE (Ω) RESISTANCE (Ω) RESISTANCE (Ω) Fig.5 Resistance to soldering heat Fig.6 Rapid change of temperature Fig.7 Damp heat, steady state 6.0 5.0 4.0 3.0 2.0 JIS C 5201-1 4.25.1 SAMPLE SIZE : n=24pcs 70°C 1,000h OVERLOAD : THE RATED VOLTAGE 6.0 5.0 4.0 3.0 2.0 ∆R/R (%) JIS C 5201-1 4.25.3 SAMPLE SIZE : n=24pcs 125°C WITH NO LOAD 1,000h ∆R/R (%) 1.0 0 −1.0 −2.0 −3.0 −4.0 −5.0 −6.0 10 100 1k 10k 100k 1M 1.0 0 −1.0 −2.0 −3.0 −4.0 −5.0 −6.0 10 100 1k 10k 100k 1M RESISTANCE (Ω) RESISTANCE (Ω) Fig.8 Endurance at 70°C Fig.9 Endurance Rev.B 4/4 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1