MNR35J5RJ331

MNR35 Resistors Chip resistor networks MNR35 (3216×5 size) zFeatures 1) Common terminals yield area 40% smaller than that of the MNR38. 2) 8-element construction makes the MNR35 ideal for bus line pull-up / pull-down. 3) Convex electrodes Easy to check the fillet after soldering is finished. 4) Compatible with a wide range of mounting equipment. Squared corners make it excellent for mounting using image recognition devices. 5) ROHM resistors have approved ISO-9001 certification. Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the product before using or ordering it. zRatings Item Rated power Conditions Specifications Power must be derated according to the power derating curve in Figure 1 when ambient temperature exceeds 70°C. 0.063W (1 / 16W) at 70°C POWER LOAD (%) 100 80 60 40 20 0 −55 0 70 100 125 AMBIENT TEMPERATURE (°C) Fig.1 Rated voltage The voltage rating is calculated by the following equation. If the value obtained exceeds the limiting element voltage, the voltage rating is equal to the maximum operating voltage. E: Rated voltage (V) E= P×R P: Rated power (W) Limiting element voltage R: Nominal resistance (Ω) Nominal resistance 50V See Table 1. −55°C~+125°C Operating temperature Table 1 Resistance tolerance J (±5%) Resistance range (Ω) 56≤R≤100k (E12) Resistance temperature coefficient (ppm / °C) ±200 •Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that is greater than its rated voltage. 1/4 MNR35 Resistors zCharacteristics Guaranteed value Resistor type Item Test conditions (JIS C 5201-1) J : ±5% Resistance Variation of resistance with temperature JIS C 5201-1 4.5 JIS C 5201-1 4.8 Measurement : −55 / +25 / +125°C See Table.1 JIS C 5201-1 4.13 Rated voltage (current) ×2.5, 2s. Limiting Element Voltage×2 : 100V ± (2.0%+0.1Ω) Overload A new uniform coating of minimum of 95% of the surface being immersed and no soldering damage. Solderability JIS C 5201-1 4.17 Rosin·Ethanol (25%WT) Soldering condition : 235±5°C Duration of immersion : 2.0±0.5s. ± (1.0%+0.05Ω) No remarkable abnormality on the appearance. Resistance to soldering heat Rapid change of temperature JIS C 5201-1 4.18 Soldering condition : 260±5°C Duration of immersion : 10±1s. ± (1.0%+0.05Ω) JIS C 5201-1 4.19 Test temp. : −55°C~+125°C 5cyc ± (3.0%+0.1Ω) JIS C 5201-1 4.24 40°C, 93%RH Test time : 1,000h~1,048h ± (3.0%+0.1Ω) JIS C 5201-1 4.25.1 Rated voltage (current), 70°C 1.5h : ON − 0.5h : OFF Test time : 1,000h~1,048h ± (3.0%+0.1Ω) JIS C 5201-1 4.25.3 125°C Test time : 1,000h~1,048h ± (1.0%+0.05Ω) JIS C 5201-1 4.29 23±5°C, Immersion cleaning, 5±0.5min. Solvent : 2-propanol Damp heat, steady state Endurance at 70°C Endurance Resistance to solvent ± (1.0%+0.05Ω) Without mechanical damage such as breaks. Bend strength of the end face plating JIS C 5201-1 4.33 zExternal dimensions (Units : mm) Cross section A-A' 6.4±0.4 ∗1.27 2 1 6 1 1 1 B Material Max.0.5 A' R103 0.5±0.3 A 3.1±0.2 5 Cross section B-B' 6 1 5 0.55±0.1 B' 0.5±0.2 1.0±0.2 2 3 4 1 Thick dielectric glaze of ruthenium 2 Thick film of silver for primary electrode 3 Nickel-coated secondary electrode 4 External electrode coated with Sn/Pb or Sn 5 Alumina substrate 6 Overcoating 0.8±0.2 ∗ Pitch of the upper electrode. 2/4 MNR35 Resistors zEquivalent circuit R1 R8 R7 R6 R2 R3 R4 R5 R1 = R2 = R3 = R4 = R5 = R6 = R7 = R8 zPackaging Reel Taping P2 E B0 02 04 06 08 06 D 04 B 02 A 08 W F φD 0 P0 A0 K P1 C (Units: mm) Label EIAJ ET-7200A compliant W F E A0 B0 12.0±0.3 5.5±0.05 1.75±0.1 3.4±0.1 6.6±0.1 D0 P0 P1 P2 K +0.1 φ1.5 0 4.0±0.1 4.0±0.1 2.0±0.05 1.0±0.15 (Units: mm) A φ180 B 0 −3 φ60 +1 0 C 13±0.3 D φ13±0.2 zProduct designation Part No. Packaging / Processing specifications Code J5 Part No. MNR35 Packaging Taping Package style Embossed reel Circuit configuration code R MNR35 Resistance tolerance J ±5% Nominal resistance 3-digit IEC coding system 3/4 MNR35 Resistors JIS C 5201-1 4.5 SAMPLE SIZE : n=40pcs 20°C 65%RH 5.0 3.0 2.0 1.0 0 −1.0 −2.0 −3.0 −4.0 −5.0 10 100 1k 10k 100k 300 0 −100 −2.0 −200 −4.0 −300 −400 15 100 1k 10k −6.0 100k 1k 10k 100k Fig.2 Resistance Fig.3 Variation resistance with temperature Fig.4 Overload 6.0 3.0 JIS C 5201-1 4.19 SAMPLE SIZE : n=16pcs −55°C / 125°C 5cyc 2.0 ∆R/R (%) 0 2.0 0 0 −1.0 −1.0 −2.0 −2.0 −2.0 −4.0 100 1k 10k −3.0 100k 10 100 RESISTANCE (Ω) 1k 10k −6.0 100k ∆R/R (%) 2.0 0 −2.0 – 4.0 −4.0 – 6.0 −6.0 100 1k 10k 100k 10k 100k 2.0 JIS C 5201-1 4.25.3 SAMPLE SIZE : n=16pcs 125°C WITH NO LOAD 1,000h 4.0 – 2.0 1k Fig.7 Damp heat, steady state 6.0 JIS C 5202 7.9 SAMPLE SIZE : n = 16pcs 60°C 95%RH 1,000h OVERLOAD : THE RATED VOLTAGE 0 100 RESISTANCE (Ω) Fig.6 Rapid change of temperature 6.0 2.0 10 RESISTANCE (Ω) Fig.5 Resistance to soldering heat 4.0 JIS C 5201-1 4.24 SAMPLE SIZE : n=16pcs 40°C 93%RH WITH NO LOAD 1,000h 4.0 1.0 10 100 RESISTANCE (Ω) JIS C 5201-1 4.18 SAMPLE SIZE : n=16pcs SOLDERING CONDITION : 260°C 10s 10 10 RESISTANCE (Ω) 1.0 ∆R/R (%) 0 RESISTANCE (Ω) 2.0 ∆R / R (%) 4.0 2.0 100 3.0 −3.0 JIS C 5201-1 4.13 SAMPLE SIZE : n=16pcs RATED VOLTAGE × 2.5TIMES 2s LIMITING ELEMENT VOLTAGE×2 : 100V 200 ∆R/R (%) −6.0 6.0 JIS C 5201-1 4.8 SAMPLE SIZE : n=16pcs 25°C / −55°C 25°C / 125°C JIS C 5201-1 4.29 SAMPLE SIZE : n=16pcs IPA, 5min. 1.5 RESISTANCE CHANGE (%) DC RESISTANCE (%) 4.0 400 ∆R/R (%) 6.0 TEMPERATURE COEFFICIENT (ppm / °C) zElectrical characteristics 1.0 0.5 0 −0.5 −1.0 −1.5 10 100 1k 10k 100k −2.0 15 100 1k 10k 100k RESISTANCE (Ω) RESISTANCE (Ω) RESISTANCE (Ω) Fig.8 Endurance (under load in damp environment) Fig.9 Endurance Fig.10 Resistance to solvents 4/4