RCN02M1PPEB550014

RCN02 Resistors Chip type attenuator (π type) RCN02 Features 1) Compare with single type 2) Guarantee the attenuation (±0.3db, ±0.5db) 3) Mounting area 50% less 4) Big reduction for mounting cost (3 times → Once) Quick reference The design and specifications are subject to change without prior notice. Before ordering or using, please check the latest technical specifications. Part No. Size code 1010 (0404) No. of terminals No. of elements Rated power (70°C) 0.04W / package Impedance 50Ω Voltage standing wave ratio Operating temperature range (°C) −55 to +125 RCN02 4 3 MAX 1.3 External dimensions (Unit: mm) Marking (Terminal No.4) 1.0 0.1 ± 0.25 0.1 0.2 0.1 1.0 0.1 Equivalent Circuit Diagram 4 R1 R2 1 R2 2 3 ± +0.1 0.33 −0.05 +0.05 0.34 −0.1 ± 0.35 0.1 ± ± 1/2 RCN02 Resistors Product designation RCN02M1 Part No. PPEA3 Circuit Code Specification PPE 5003 Attenuation, Attenuation limitation Code A3 5001 A3 5002 A3 5003 A3 5004 A3 5005 A5 5006 A5 5007 A5 5008 A5 5009 A5 50010 A8 50011 A8 50012 A8 50013 B5 50014 B5 50015 B5 50016 C0 50017 C0 50018 C0 50019 C5 50019 Attenuation 1dB 2dB 3dB 4dB 5dB 6dB 7dB 8dB 9dB 10dB 11dB 12dB 13dB 14dB 15dB 16dB 17dB 18dB 19dB 20dB Limitation π Circuit ±0.3dB Packaging Specifications Code Part No. M1 Packaging specifications Paper tape (2mm Pitch) Reel φ180mm (7in.) Basic ordering unit (pcs) 10,000 Reel (φ180mm) : Compatible with JEITA standard "EIAJ ET-7200B" ±0.5dB ±0.8dB ±1.5dB ±2.0dB ±2.5dB Packaging Reel Taping P0 P2 φD 0 E A0 B0 F W 02 04 06 08 08 06 04 A B D 02 P1 Heat crimp cover / Tape Chip attenuator Thick paper mount (Underside paper tape) Feeding direction Square punchout hole T2 C Label EIAJ ET-7200B compliant (Unit : mm) W 8.0±0.3 D0 +0.1 φ1.5 0 F 3.5±0.05 P0 4.0±0.1 E 1.75±0.1 P1 2.0±0.1 A0 1.17±0.1 P2 2.0±0.05 B0 1.17±0.1 T2 Max. 0.5 (Unit : mm) A φ180 0 −1.5 B φ60 +1 0 9 C +1.0 0 D φ13±0.2 Caution : Insertion direction of device to carrier tape. Marking is on the left bottom side of the cavity to the feeding direction. 2/2 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1