RPI-1133_05

RPI-1133 Photointerrupter, Small type External dimensions (Unit : mm) 4.2 Thorugh hole Absolute maximum ratings (Ta=25°C) Parameter Forward current Input (LED) Reverse voltage Power dissipation Output (photo IC) Power supply voltage Output current Power dissipation Symbol IF VR PD VCC IO PD Topr Tstg Limits 50 5 80 7 10 80 −20 to +60 −40 to +100 Unit mA V mW 3.2 4 0.3 Applications Optical control equipment 5-φ0.8 1.25 1.25 Gap 1.1±0.1 Cross-section A-A A 1.2 2.8 Optical axis center C0.8 (1.7) V mA mW Features 1) Small slit width (0.3mm) for high precision. 2) Fast response. 3) Built-in visible light filter. 5 2-R0.2 C0.2 Operating temperature Storage temperature °C °C 2.1 Min5.4 A φ1.2 +0.1 -0 Electrical and optical characteristics (Ta=25°C) Parameter Input characteristics Forward voltage Reverse current Power supply voltage Output low level voltage Output high level voltage Low level power supply current High level power supply current Transfer characteristics High → Low Threshold input current Hysteresis Response time Low → High Propagation delay time High → Low Propagation delay time Rise time Fall time Infrared light emitter diode Symbol VF IR VCC VOL VOH ICCL ICCH IFHL IFLH / IFHL tPLH tPHL tr tf fC Min. − − 2.0 − 2.8 − − 0.25 0.4 − − − − − − − − Typ. 1.1 − − 0.08 − 0.35 0.35 − 0.7 22 5.5 5 0.05 1 950 5 0.05 Max. 1.3 10 7.0 0.35 3.0 1.5 1.5 2.5 0.9 66 16 15 0.15 − − 15 0.15 Unit V µA V V V mA mA mA − VCC=3V, IOL=2mA VCC=3V, IF=0mA VCC=3V, IF=5mA VCC=3V, IF=0mA VCC=3V VCC=3V IF=10mA VR=5V Conditions 5-0.2 (3.2) 5-0.5 (2.5) Output characteristics − Vcc Vo GND Anode Cathode Notes: 1. Unspecified tolerance shall be ±0.2 . 2. Dimension in parenthesis are show for reference. µs VCC=3V, IF=5mA, RL=100Ω THRESHOLD INPUT CURRENT : IFHL,IFLH (mA) 1.5 1.0 RELATIVE OUTPUT VOLTAGE : VO (%) RISE FALL TIME : tr,tf (µsec) 1.3 IFHL 1.1 IFLH 0.9 0.8 100 d Cut-off frequency Peak light emitting wavelength Response time MHz nm IF=50mA 0.6 tr 0.4 λP tr tf ∗ Non-coherent Infrared light emitting diode used. Photo IC µs ∗ This product is not designed to be protected against electromagnetic wave. VCC=3V, IF=5mA, RL=100Ω 0.7 0.2 tf 0.5 −20 0 20 40 60 0.1 0.5 1.0 5.0 10 0 2.0 2.5 2.5 AMBIENT TEMPERATURE : Ta (°C) LOAD RESISTANCE : RL (kΩ) DISTANCE : d (mm) Electrical and optical characteristics curves LOW LEVEL OUTPUT VOLTAGE : VOL (V) LOW LEVEL OUTPUT VOLTAGE : VOL (V) 500 0.5 FORWARD CURRENT : IF (mA) Fig.4 Threshold input current vs. ambient temperature Fig.5 Response time Fig.6vs. load resistance Fig.6 Relative output voltage vs. distance characteristics 50 FORWARD CURRENT : IF (mA) −25°C 0°C 25°C 50°C 75°C 400 0.4 50 IF=5mA VCC Constant voltage circuit 50% +3V output Input tPHL tPLH 40 40 30 20 47Ω tr=tf =0.01µs ZO=50 Ω 300 0.3 RL 30 IOL=8mA IOL=5mA 20 200 0.2 Amplifier Output VOH 90% 1.5V GND 10% tf tr VOL 10 100 0.1 IOL=2mA 10 0 0 0 0.4 0.8 1.2 1.6 2.0 0 0 5.0 10 0 -20 0 20 40 60 −20 0 20 40 60 80 100 FORWARD VOLTAGE : VF (V) LOW LEVEL OUTPUT CURRENT : IOL (mA) AMBIENT TEMPERATURE : Ta(°C) AMBIENT TEMPERATURE : Ta (°C) Fig.1 Forward current vs. forward voltage Fig.2 Low level output voltage vs. low level output current Fig.3 Low level output voltage vs. ambient temperature Fig.7 Forward current falloff Fig.8 Response time measurement circuit Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1