SE3003-DC70A

SE3003-DC70A Printheads Under development High speed thermal printhead (with thermal historical control) SE3003-DC70A High speed, high quality, and high durability are achieved by using step free structure with high performance partial glaze and highly conductive overcoat layer. SE300*-DC70A series are lined up which can accommodate with all types of barcode labeling printers from Direct to Thermal Transfer, normal to high speed (over 300mm/s). Applications Bar code printer Label printer Packaging printer ATM Ticket printer Features 1) ROHM new technology “STEP FREE” structure will provide, high corrosion resistance, better resistance against scratching damage, high efficiency. 2) High-hardness protect cote type “W-coat” is employed with 150km abrasion life-time. 3) A built in history-control functionality, high-speed printing up to 300mm / s can be achieved at 300dpi with clear print image. External dimensions (Unit : mm) MAX.φ20 90± 0.5 81.312 DOT No.1 DOT No.1 20± 0.3 20.656± 0.2 (4.344) 17.8± 0.2 6± 0.5 40± 0.3 (25) MAX.48 MIN.4.3 (36) MAX.5 MAX.12 φ3 H10 Length 4 Effective Depth 3 M3 Effective Depth 3 φ3 H10 Effective Depth 3 #2 TYPE OF PRINTHEAD #20 #6 #1 CONNECTOR:A #1 #19 CONNECTOR:B 7.3± 0.3 25± 0.5 (3.5) 1/3 SE3003-DC70A Printheads Equivalent circuit VH (COM) 220µF 35V Under development DOT #960 DOT #1 GND 0.1µF 50V VDD (+5) / STB2 / STB1 BEO / RESET LATCH REGISTER SHIFT REGISTER SHIFT REGISTER CLK (CP) DI2 DI1 / LOAD START INC SEL2 SEL1 TM TM THERMISTOR 30kΩ B: 3950K TO EACH IC DI No. DI2 DI1 DOT No. 960 to 449 448 to 1 / STB No. / STB2 / STB1 DOT No. 960 to 449 448 to 1 Pin assignments CONNECTOR : A No. 1 3 5 7 9 11 13 15 17 19 Circuit No. 2 4 6 8 10 12 14 16 18 20 Circuit BEO DI2 CLK (CP) START DI1 SEL1 /STB2 TM SENS1 SENS3 CONNECTOR : B No. 1 3 5 Circuit VH (COM) VH (COM) GND No. 2 4 6 Circuit VH (COM) GND GND VDD GND GND /LOAD INC SEL2 /RESET /STB1 TM SENS2 2/3 SE3003-DC70A Printheads Characteristics Parameter Effective printing width Dot pitch Total dot number Average resistance value Applied voltage Applied power Print cycle Maximum number of dots energized simultaneously Maximum clock frequency Maximum roller diameter Running life / pulse life Operating temperature Symbol − − − Rave VH PO SLT − − − − − Typical 81.3 0.0847 960 850 24 0.61 0.28 960 8 φ20 150/(1×108) 5 to 45 Unit mm mm dots Ω V W/dot ms dots MHz mm km/pulses °C Under development 3/3 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1