SFR03EZPF1000

RCG e3 www.vishay.com Vishay Draloric Green Thick Film Chip Resistors FEATURES • Green resistor - does not use RoHS exemptions • Stability R/R = 1 % for 1000 h at 70 ° C • 2 mm pitch packaging option for 0603 size • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 STANDARD ELECTRICAL SPECIFICATIONS TYPE CASE SIZE IMPERIAL CASE SIZE METRIC POWER RATING P70 W LIMITING ELEMENT VOLTAGE Umax. ACRMS/DC V 0.063 50 TEMPERATURE COEFFICIENT ± ppm/K TOLERANCE ±% 100 RCG0402 0402 RR1005M 150 to 10M 0.5, 1 150 200 RESISTANCE RANGE  1.0 to 147 5 SERIES E24; E96 1.0 to 10M E24 Zero-Ohm-Resistor: Rmax. = 20 m, Imax. = 1.5 A RCG0603 0603 0.1 RR1608M 75 100 0.5, 1 200 5 1.0 to 10M E24; E96 E24 Zero-Ohm-Resistor: Rmax. = 20 m, Imax. = 2.0 A RCG0805 0805 0.125 RR2012M 150 100 0.5, 1 200 5 1.0 to 10M E24; E96 E24 Zero-Ohm-Resistor: Rmax. = 20 m, Imax. = 2.5 A RCG1206 1206 0.25 RR3216M 200 100 0.5, 1 200 5 1.0 to 10M E24; E96 E24 Zero-Ohm-Resistor: Rmax. = 20 m, Imax. = 3.5 A Notes • These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime. • Marking: See datasheet “Surface Mount Resistor Marking” (document number 20020). • Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material. TECHNICAL SPECIFICATIONS PARAMETER Rated dissipation P70 (1) UNIT RCG0402 RCG0603 RCG0805 RCG1206 W 0.063 0.1 0.125 0.25 Operating voltage Umax. ACRMS/DC V 50 75 150 200 Insulation voltage Uins (1 min) V 75 100 200 300 5.5 10 Insulation resistance  Operating temperature range °C Mass mg > 109 - 55 to + 155 0.65 2 Note (1) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded. Revision: 01-Sep-14 Document Number: 20047 1 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 RCG e3 www.vishay.com Vishay Draloric PART NUMBER AND PRODUCT DESCRIPTION PART NUMBER: RCG080510K0FKEA R C G 0 8 0 5 1 0 K 0 F K E TYPE VALUE TOLERANCE TCR PACKAGING RCG0402 RCG0603 RCG0805 RCG1206 R = Decimal K = Thousand M = Million 0000 = 0  Jumper D = ± 0.5 % F = ± 1.0 % J = ± 5.0 % Z = Jumper K = ± 100 ppm/K L = ± 150 ppm/K N = ± 200 ppm/K 0 = Jumper EA, EB, EC, ED, EE, EI, EL 100 10K 1% EA TYPE TCR RESISTANCE VALUE TOLERANCE PACKAGING RCG0402 RCG0603 RCG0805 RCG1206 ± 100 ppm/K ± 150 ppm/K ± 200 ppm/K 10R = 10  10K = 10 k 1M = 1 M 0R0 = Jumper ± 0.5 % ±1% ±5% EA, EB, EC, ED, EE, EI, EL A PRODUCT DESCRIPTION: RCG0805 100 10K 1 % EA RCG0805 PACKAGING TYPE CODE QUANTITY CARRIER TAPE WIDTH PITCH ED 10 000 Paper tape acc. to IEC 60286-3 Type 1a 8 mm 2 mm RCG0402 RCG0603 RCG0805 RCG1206 Revision: 01-Sep-14 EE 50 000 EI 5000 ED 10 000 EL 20 000 EE 50 000 EA 5000 EB 10 000 EC 20 000 EA 5000 EB 10 000 EC 20 000 EA 5000 EB 10 000 EC 20 000 REEL DIAMETER 180 mm/7" 330 mm/13" 180 mm/7" Paper tape acc. to IEC 60268-3 Type 1a 180 mm/7" 8 mm 2 mm 285 mm/11.25" 330 mm/13" 180 mm/7" Paper tape acc. to IEC 60268-3 Type 1a 8 mm 4 mm 285 mm/11.25" 330 mm/13" 180 mm/7" Paper tape acc. to IEC 60268-3 Type 1a 8 mm 4 mm 285 mm/11.25" 330 mm/13" 180 mm/7" Paper tape acc. to IEC 60268-3 Type 1a 8 mm 4 mm 285 mm/11.25" 330 mm/13" Document Number: 20047 2 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 RCG e3 www.vishay.com Vishay Draloric DIMENSIONS in millimeters SIZE SOLDER PAD DIMENSIONS DIMENSIONS IMPERIAL METRIC L W H 0402 RR1005M 1.0 ± 0.05 0.5 ± 0.05 0603 RR1608M 1.55 + 0.10 - 0.05 0805 RR2012M 2.0 1206 RR3216M 3.2 REFLOW SOLDERING T1 T2 a b l 0.35 ± 0.05 0.25 ± 0.05 0.2 ± 0.1 0.4 0.6 0.5 0.85 ± 0.1 0.45 ± 0.05 0.3 ± 0.2 0.3 ± 0.2 0.5 0.9 + 0.20 - 0.10 1.25 ± 0.15 0.45 ± 0.05 0.3 + 0.20 - 0.10 0.3 ± 0.2 0.7 + 0.10 - 0.20 1.6 ± 0.15 0.55 ± 0.05 0.45 ± 0.2 0.4 ± 0.2 0.9 WAVE SOLDERING a b l 1.0 0.9 0.9 1.0 1.3 1.2 0.9 1.3 1.3 1.7 2.0 1.1 1.7 2.3 Fraction of Rated Dissipation P70 FUNCTIONAL PERFORMANCE 100 % 50 0 - 50 Derating 0 50 100 °C 150 70 Ambient Temperature in amb GREEN REQUIREMENTS SUBSTANCES CONCENTRATION LIMIT Lead (Pb) < 1000 ppm Mercury (Hg) < 1000 ppm Cadmium (Cd) < 100 ppm Hexavalent Chronium < 1000 ppm Polybrominated Biphenyl (PBB) < 1000 ppm Polybrominated Diphenyl Ether (PBDE) < 1000 ppm Bromine (Br) < 900 ppm Chlorine (Cl) Sum of Bromine and Chlorine < 900 ppm  1500 ppm max. Antimony (Sb) < 900 ppm Red Phosphorous < 100 ppm Notes • No exemptions (e.g. Pb in glass) may be applied to any substances or application for the “Green” category • All concentration levels are based on homogenous materials Revision: 01-Sep-14 Document Number: 20047 3 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 RCG e3 www.vishay.com Vishay Draloric TEST PROCEDURES AND REQUIREMENTS IEC EN 60115-1 60068-2 CLAUSE TEST METHOD TEST REQUIREMENTS PERMISSIBLE CHANGE (R) PROCEDURE Stability for product types: RCG e3 4.5 - Resistance - 4.7 - Voltage proof U = 1.4 x Uins; 60 s 4.13 - Short time overload U = 2.5 x P 70 x R  2 x Umax.; Duration acc. to style 4.17.2 58 (Td) Solderability Solder bath method; Sn96.5Ag3Cu0.5 non-activated flux; (245 ± 5) °C (3 ± 0.3) s 4.8.4.2 - Temperature coefficient (20/- 55/20) °C and (20/125/20) °C 4.32 21 (Uu3) Shear (adhesion) RR 1608 and smaller: 9 N RR 2012 and larger: 45 N 4.33 21 (Uu1) Substrate bending Depth 2 mm; 3 times 4.23 - Climatic sequence: - 4.23.2 2 (Ba) Dry heat 125 °C; 16 h 4.23.3 30 (Db) Damp heat, cyclic 55 °C;  90 % RH; 24 h; 1 cycle 4.23.4 1 (Aa) Cold - 55 °C; 2 h 4.23.5 13 (M) Low air pressure 1 kPa; (25 ± 10) °C; 1 h 4.23.6 30 (Db) Damp heat, cyclic 55 °C;  90 % RH; 24 h; 5 cycles 4.23.7 - DC load 4.25.1 - Endurance at 70 °C STABILITY CLASS 1 OR BETTER STABILITY CLASS 2 OR BETTER 1 to 10 M 1 to 10 M ± 0.5 %, ± 1 % ±5% No flashover or breakdown ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 ) Good tinning ( 95 % covered) no visible damage ± 100 ppm/K, ± 150 ppm/K ± 200 ppm/K No visible damage No visible damage, no open circuit in bent position ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 ) ± (1 % R + 0.05 ) ± (2 % R + 0.1 ) 70 °C; 1000 h ± (1 % R + 0.05 ) ± (2 % R + 0.1 ) ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 ) U= P 70 x R U = P 70 x R  Umax.; 1.5 h on; 0.5 h off; 58 (Td) Resistance to soldering heat Solder bath method (260 ± 5) °C; (10 ± 1) s 4.35 - Flamability, needle flame test IEC 60695-11-5; 10 s 4.24 78 (Cab) Damp heat, steady state (40 ± 2) °C; (93 ± 3) % RH; 56 days ± (1 % R + 0.05 ) ± (1 % R + 0.1 ) 4.25.3 - Endurance at upper category temperature 155 °C, 1000 h ± (1 % R + 0.05 ) ± (2 % R + 0.1 ) 4.40 - Electrostatic discharge (human body model) IEC 61340-3-1; 3 pos. + 3 neg. discharges; ESD test voltage acc. to size 4.18.2 Revision: 01-Sep-14 No burning after 30 s ± (1 % R + 0.05 ) Document Number: 20047 4 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 RCG e3 www.vishay.com Vishay Draloric TEST PROCEDURES AND REQUIREMENTS IEC EN 60115-1 60068-2 CLAUSE TEST METHOD TEST REQUIREMENTS PERMISSIBLE CHANGE (R) PROCEDURE Stability for product types: RCG e3 STABILITY CLASS 1 OR BETTER STABILITY CLASS 2 OR BETTER 1 to 10 M 1 to 10 M 4.29 45 (XA) Component solvent resistance Isopropyl alcohol; 50 °C; method 2 No visible damage 4.30 45 (XA) Solvent resistance of marking Isopropyl alcohol; 50 °C; method 1, toothbrush Marking legible, no visible damage 4.22 6 (Fc) Vibration, endurance by sweeping f = 10 Hz to 2000 Hz; x, y, z  1.5 mm; A  200 m/s2; 10 sweeps per axis 4.37 - Periodic electric overload 4.27 - Single pulse high voltage overload, 10 μs/700 μs 15 x P 70 x R  2 x Umax.; 0.1 s on; 2.5 s off; 1000 cycles ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 ) U= Û = 10 x P 70 x R  2 x Umax.; 10 pulses ± (1 % R + 0.05 ) ± (1 % R + 0.05 ) All tests are carried out in accordance with the following specifications: • EN 60115-1, generic specification • EN 140400, sectional specification • EN 140401-802, detail specification • IEC 60068-2, environmental test procedures Packaging of components is done in paper tapes according to IEC 60286-3. Revision: 01-Sep-14 Document Number: 20047 5 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2021 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 09-Jul-2021 1 Document Number: 91000