SH2002-DC90A
Printheads
Near edge thermal printhead (8dots / mm)
SH2002-DC90A
SH-DC90 series was developed with two key structures step-free and near edge for the packaging printer market which requires high speed continuous printing. It is suitable for printers in factory line where high speed 24 hours continuous printing is required. Applications Bar code printers Card printers Ticket printers General purpose compact printers Features 1) ROHM new technology “STEP FREE” structure will provide, high corrosion resistance, better resistance against scratching damage, high efficiency. 2) Inclined toward the printing surface to provide excellent printing quality even for cards and thick paper. 3) Prints directly on printing medium that cannot be bent. 4) Using a hard conductive film as a protective film on the heating element offers excellent resistance to electrostatic damage. 5) Compatible with the SH3002-DC90A (300dpi) in mechanical specifications, to facilitate the making of a series of printers. Dimensions (Unit : mm)
DOT #448 (5)
Max. 51
Max. 5
Pape
r feed
directi
on
66±0.5 56 (EFFECTIVE PRINT WIDTH)
6±0.5 DOT #1
Max. 12
#2
#20
#4
#1
#1 φ3H10 EFFECTIVE DEPTH 3
#19
JST B4PS-VH
HIROSE HIF3FC-20PA-2.54DS φ3H10 LENGTH 4 EFFECTIVE DEPTH 3
20.555±0.2
7.3±0.3
8±0.3 (13)
20±0.3 40±0.3
DOT #1 M3 EFFECTIVE DEPTH 3
Note: No heat history control function inside the thermal printhead. External heat history control is required for high speed printing.
25±0.5
(21.3)
Rev.A
1/5
SH2002-DC90A
Printheads
Characteristics
Parameter Effective printing width Dot pitch Total dot number Average resistance value Applied voltage Applied power Print cycle Maximum number of dots energized simultaneously Maximum clock frequency Maximum roller diameter Running life / pulse life Operating temperature Symbol − − − Rave VH PO SLT − − − − − Typical 56 0.125 448 550 24 0.86 0.42 448 10 − 150 / 1x108 5 to 45 Unit mm mm dots Ω V W / dot ms dots MHz mm km / pulses
°C
Pin configuration
HIROSE No. 1 3 5 7 9 11 13 15 17 19 Circuit VDD GND N.C. LAT GND N.C. VDD STB1 TM SENS2 No. 2 4 6 8 10 12 14 16 18 20 Circuit BEO DI2 CLK GND DI1 GND STB2 TM SENS1 SENS3 JST No. 1 2 3 4 Circuit VH VH GND GND
Rev.A
2/5
SH2002-DC90A
Printheads
Timing chart
tw CLK
CLK (CLOCK)
t setup DI t hold DI
DI(DATA IN)
"High":BLACK "LOW" :WHITE
BEO
t setup LAT
t hold LAT
min.12.5 μsec (Max. tdo)*
/LAT (LATCH)
"High": HOLD "LOW" : THROUGH
tw LAT
t setup ST B
/STBn (STROBE)
tdo
tdo
DRIVER OUT
*If delay time for Driver Out can not be secured enough, there is a possibility that VH would fluctuate greatly. Please design the circuit so that VH does not exceed peak voltage (Vp).
Rev.A
3/5
SH2002-DC90A
Printheads
Equivalent circuit
DOT#448 VH (COM) 220µ F 35V #448 VDD 0.1µ F 50V #193 #192 #1 DOT#1
GND
BEO
/STB2 /STB1
/LAT
LATCH REGISTER
CLK DI2 DI1
SHIFT REGISTER
SHIFT REGISTER
SENS1 SENS2 SENS3 TM TM
THERMISTOR 30kΩ B:3950K
DI No. DI2 DI1
DOT No. 448 to 193 192 to 1 Fig. 2
STB No. STB 2 STB 1
DOT No. 448 to 193 192 to 1
Rev.A
4/5
SH2002-DC90A
Printheads
Electrical characteristics curves
1.5 1.4
SUPPLY ENERGY (MAX) (mJ / dot)
1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 SCANNING LINE TIME (ms / line)
RESISTANCE VALUE : (kΩ)
180 160 140 120 100 80 60 40 20 0 −10 0 10 20 30 40
R25=30kΩ B=3950k
1.2
OPTICAL DENSITY
1.0 0.8 0.6 0.4 0.2 0.0 0.060 0.100 0.150 0.200 0.250
50
60
70
ENERGY (mJ / dot)
TEMPERATURE : (°C)
Fig. 3 Representative density curve
Fig. 4 Maximum energy curve
Fig. 5 Thermistor curve
Rev.A
5/5
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of which would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM cannot be held responsible for any damages arising from the use of the products under conditions out of the range of the specifications or due to non-compliance with the NOTES specified in this catalog.
Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact your nearest sales office.
ROHM Customer Support System
www.rohm.com
Copyright © 2007 ROHM CO.,LTD.
THE AMERICAS / EUPOPE / ASIA / JAPAN
Contact us : webmaster@ rohm.co. jp
21, Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan
TEL : +81-75-311-2121 FAX : +81-75-315-0172
Appendix1-Rev2.0
很抱歉,暂时无法提供与“SH2002-DC90A_07”相匹配的价格&库存,您可以联系我们找货
免费人工找货