SLA560BN4T3F

SLI-560x/SLA-560x/SLA560x Series 　　　　 Data Sheet ■Features • Viewing angle 2θ 1/2 : 40° ■Outline • High brightness Color Type U D Y E B WB M ■Dimensions ■Recommended Solder Pattern Tolerance : ±0.2 (unit : mm) (unit : mm) ■Specifications Absolute Maximum Ratings (Ta=25ºC) Emitting Part No. Power Forward Peak Forward Color Dissipation Current Current Voltage PD(mW) IF(mA) IFP(mA) VR(V) SLI-560DT Typ. Topr(ºC) Tstg(ºC) (V) IF Max. AlGaInP (mA) (μA) Orange 125 50 200*2 9 Yellowish green Emitting -30～+85 -40～+100 1.9 20 75 25 60*1 4 Power Forward Peak Forward -25～+85 -30～+100 GREEN SLA560WBN2PT*3 InGaN Dissipation 2.3 20 9 10 4 Forward Voltage VF Reverse Current IR Current Current Voltage Topr(ºC) Tstg(ºC) Min. Typ. IF (mA) (mcd) (mcd) (mA) 126 100*2 5 20 563 20 42 100 -20～+80 -30～100 Dominant Wavelength λD /Chromaticity coordinate(x,y) IF Max. VR Typ. (mA) (μA) (V) (nm) (mA) (mcd) (mcd) (mA) 523 1350 3000 3.2 20 5 10 470 470 (x,y)（031, 0.31) IF Luminous Intensity IV (V) 100 30 300 1000 611 Typ. 120 BLUE WHITE IF Electrical and Optical Characteristics (Ta=25ºC) Reverse PD(mW) IF(mA) IFP(mA) VR(V) SLA560BN2T 100 Operating Temp. Storage Temp. Color SLA560BN4T (V) 591 Chip Structure SLA560EN4T Luminous Intensity IV 630 Absolute Maximum Ratings (Ta=25ºC) Part No. Typ. (nm) Yellow GaP Peak Wavelength λP VR Red SLI-560YT SLA-560MT Forward Voltage VF Reverse Current IR Operating Temp. Storage Temp. Chip Structure SLI-560UT Electrical and Optical Characteristics (Ta=25ºC) Reverse 20 Min. Typ. 300 680 IF 20 1000 2200 1500 3300 *1 : Duty1/5, 200Hz,*2：Duty1/10,　1kHz、*3:Brightness for white color is noted with chromaticity coordinate(x,y). ＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿ www.rohm.com 1/10 ©2022 ROHM Co., Ltd. All rights reserved 2022.2 - Rev.008 　　　　 [SLI-560x/SLA-560x/SLA560x series] [Data Sheet] ■Electrical Characteristics Curves Reference Fig.2 Luminous Intensity 　　　　　Atmosphere Temperature FORWARD CURRENT : IF [mA] Ta=25ºC SLI-560UT SLI-560DT SLI-560YT RELATIVE LUMINOUS INTENSITY Fig.1 Forward Current - Forward Voltages FORWARD VOLTAGE : VF [V] FORWARD CURRENT : IF [mA] Fig.4 Derating MAXIMUM FORWARD CURRENT : [mA] RELATIVE LUMINOUS INTENSITY Ta=25ºC SLI-560DT SLI-560YT SLI-560UT ATMOSPHERE TEMPERATURE : Ta [ºC] Fig.3 Luminous Intensity - Forward Current SLI-560UT SLI-560DT SLI-560YT IF=20mA SLI-560UT SLI-560DT SLI-560YT AMBIENT TEMPERATURE : Ta [ºC] ＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿ www.rohm.com 2/10 ©2022 ROHM Co., Ltd. All rights reserved 2022.2 - Rev.008 [SLI-560x/SLA-560x/SLA560x series] [Data Sheet] ■Electrical Characteristics Curves Reference SLA560EN4T SLA560BN4T SLA560BN2T SLA560WBN2PT Fig.2 Luminous Intensity 　　　　　Atmosphere Temperature Ta=25ºC RELATIVE LUMINOUS INTENSITY FORWARD CURRENT : IF [mA] Fig.1 Forward Current - Forward Voltages FORWARD CURRENT : IF [mA] Fig.4 Derating MAXIMUM FORWARD CURRENT : [mA] RELATIVE LUMINOUS INTENSITY Fig.3 Luminous Intensity - Forward Current Ta=25ºC IF=20mA ATMOSPHERE TEMPERATURE : Ta [ºC] FORWARD VOLTAGE : VF [V] SLA560EN4T SLA560BN4T SLA560BN2T SLA560WBN2PT SLA560EN4T SLA560BN4T SLA560BN2T SLA560WBN2PT SLA560EN4T SLA560BN4T SLA560BN2T SLA560WBN2PT AMBIENT TEMPERATURE : Ta [ºC] ＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿ www.rohm.com 3/10 ©2022 ROHM Co., Ltd. All rights reserved 2022.2 - Rev.008 　　　　 [SLI-560x/SLA-560x/SLA560x series] [Data Sheet] ■Electrical Characteristics Curves Reference Fig.2 Luminous Intensity 　　　　　Atmosphere Temperature FORWARD CURRENT : IF [mA] Ta=25ºC SLA-560MT RELATIVE LUMINOUS INTENSITY Fig.1 Forward Current - Forward Voltages IF=20mA SLA-560MT ATMOSPHERE TEMPERATURE : Ta [ºC] FORWARD VOLTAGE : VF [V] Ta=25ºC SLA-560MT FORWARD CURRENT : IF [mA] Fig.4 Derating MAXIMUM FORWARD CURRENT : [mA] RELATIVE LUMINOUS INTENSITY Fig.3 Luminous Intensity - Forward Current SLA-560MT AMBIENT TEMPERATURE : Ta [ºC] ＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿ www.rohm.com 4/10 ©2022 ROHM Co., Ltd. All rights reserved 2022.2 - Rev.008 [SLI-560x/SLA-560x/SLA560x series] 　　　　 [Data Sheet] ■Viewing Angle Reference SCANNING ANGLE (deg) SLI-560x series RELATIVE INTENSITY (%) SCANNING ANGLE (deg) SLA-560MT RELATIVE INTENSITY (%) SCANNING ANGLE (deg) RELATIVE INTENSITY (%) SCANNING ANGLE (deg) RELATIVE INTENSITY (%) ＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿ www.rohm.com 5/10 ©2022 ROHM Co., Ltd. All rights reserved 2022.2 - Rev.008 　　　　 [SLI-560x/SLA-560x/SLA560x series] [Data Sheet] ■Rank Reference of Brightness* *Measurement tolerance:±10% Red(U) Rank Iv (mcd) (Ta=25ºC, IF＝20mA) XE XF XG XH XJ XK XL XM XN 47～ 68 68～ 100 100～150 150～220 220～330 330～470 470～680 680～1000 XP XQ XR XS XT XU 1000～1500 1500～2200 2200～ 3300 3300～4700 4700～6800 6800～10000 10000～15000 SLI-560UT Orange(D) Rank Iv (mcd) (Ta=25ºC, IF＝20mA) XE XF XG XH XJ XK XL XM XN 47～ 68 68～ 100 100～150 150～220 220～330 330～470 470～680 680～1000 XP XQ XR XS XT XU 1000～1500 1500～2200 2200～ 3300 3300～4700 4700～6800 6800～10000 10000～15000 SLI-560DT Yellow (Y) Rank Iv (mcd) (Ta=25ºC, IF＝20mA) XE XF XG 47～ 68 68～ 100 100～150 XH 150～ XJ 220 XK XL XM XN 220～330 330～470 470～680 680～1000 XP XQ XR XS XT XU 1000～1500 1500～2200 2200～ 3300 3300～4700 4700～6800 6800～10000 10000～15000 SLI-560YT Yellowish Green(M) Rank Iv (mcd) XE (Ta=25ºC, IF＝20mA) XF XG XH XJ XK XL XM XN 47～ 68 68～ 100 100～150 150～220 220～330 330～470 470～680 680～1000 XP XQ XR XS XT XU 1000～1500 1500～2200 2200～ 3300 3300～4700 4700～6800 6800～10000 10000～15000 SLA-560MT Green（E) Rank Iv (mcd) (Ta=25ºC, IF＝20mA) XH XJ XK XL XM XN 135～240 200～360 300～520 420～750 610～1100 900～1650 XP XQ XR XS XT XU 1350～2400 2000～ 3600 3000～5200 4200～7500 6100～11000 9000～16500 SLA560EN4T Blue (B) Rank Iv (mcd) SLA560BC4T Rank Iv (mcd) (Ta=25ºC, IF＝20mA) XH XJ XK XL XM XN 135～240 200～360 300～520 420～750 610～1100 900～1650 XH XJ XK XL XM 150～220 220～330 330～473 470～680 680～1000 XN XP XQ XR XS XT XU 1350～2400 2000～ 3600 3000～5200 4200～7500 6100～11000 9000～16500 XP XQ XR XS XT XU 1000～1500 1500～2200 2200～ 3300 3300～4700 4700～6800 6800～10000 10000～15000 SLA560BN2T White (WB) Rank Iv (mcd) (Ta=25ºC, IF＝20mA) XJ XK XL XM 220～330 330～473 470～680 680～1000 XN XP XQ XR XS XT XU 1000～1500 1500～2200 2200～ 3300 3300～4700 4700～6800 6800～10000 10000～15000 SLA560WBN2PT ■Chromaticity Diagram 0.4 CIE y C B （Ｔａ＝25℃、If=20mA) 0.3 Ａ A 0.2 0.2 0.3 CIE x 0.4 Ｂ Ｃ x y x y x y 0.283 0.244 0.280 0.312 0.330 0.307 0.299 0.269 0.330 0.370 0.354 0.339 0.280 0.312 0.330 0.307 0.363 0.398 0.260 0.272 0.299 0.269 0.330 0.370 Measurement tolerance：±0.02 ＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿ www.rohm.com 6/10 ©2022 ROHM Co., Ltd. All rights reserved 2022.2 - Rev.008 　　　　 [SLI-560x/SLA-560x/SLA560x series] [Data Sheet] ■Part No. Construction *"-"will be taken out for emitting color Special Code will be applied for Chromaticity rank Rank sign WB/B/E series. Emitting color WB/B/E series. (for white LED） (Brightness Rank)* S L Series name I － 5 6 0 Package type U T Emitting Color T Resin Color 3 1-Die Circular Type High Brightness LED Lamps V Red R DiffusedColored SLI 1-Die Circular Type Low Current High Brightness LED Lamps U Red U SLR 1-Die Circular Type LED Lamps U2 Red Y DiffusedColored SLD 1-Die Oval Type High Brightness LED Lamps D Orange G DiffusedColored Y Yellow C Y2 Yellow RC P Green E Green B Blue WB White XK Taping Specification SLA M Yellowish green 2 DiffusedColored 3F 1-Element straight bulk T□□ See Taping specifications Transparent Colored T Transparent Coloreless *Concerning the Brightness rank. *Please refer to the rank chart above for luminous intensity classification. *Part name is individual for each rank. *When shipped as sample,the part name will be a representative part name. General products are free of ranks. Please contact sales if rank appointment is needed. ＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿ www.rohm.com 7/10 ©2022 ROHM Co., Ltd. All rights reserved 2022.2 - Rev.008 [SLI-560x/SLA-560x/SLA560x series] 　　　　 [Data Sheet] ■ATTENTION POINTS IN HANDLING Visual light emitting diode does not contain reinforcement materials such as glass fillers. Therefore if sudden thermal and mechanical shock are given, destruction or inferiority of luminous intensity may occur. Please take care of the handling. ■FIXATION METHOD １．ATTENTION POINTS 　(1) Please do not give excessive heat over storage temperature to resin. 　　In case that the product has to be heated in oven for the glue fixing of surface mount parts, 　　this LED should be mounted after the glue fixing. 　(2) Please avoid stress to resin at high temperature. ２． TERMINATION PROCESSING 　(1) In case of termination processing, please fix the 　　termination 　(2) Processing position, and process the reverse side 　　of LED body. 　　If stress is given during processing, It may cause 　　non-lighting failure. 　(3) Please process before soldering. ＜Good＞ ＜No good＞ To be fixed To be fixed ３． ASSEMBLY ON PC BOARD 　(1) In case of soldering on PCB, If the operation is done with stress, it may cause non-lighting 　　failure during soldering or using. Please design the through-holes of PCB suitable for lead pins 　　space or lead pins space after forming to avoid the physical stress on resin. ＜Good＞ ＜Good＞ ＜No good＞ ＜2 lead pins type＞ ＜3 lead pins type＞ 　(2) Using spacer between LED’s body and PCB is recommended. 　　In case of direct mount on PCB(SLR/SLI-343 series), please take care about clinch of LED pins 　　to avoid the remained stress and solder heat stress. 　　Enough evaluation is requested before deciding assembly and soldering conditions. Please consult with us if any problems in the evaluation stage. ＜3 lead pin type＞ ＜2 lead pin type＞ Min.15° Die bonding side Min.45° Min.15° Min.45 Min.45° Die bonding side ＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿ www.rohm.com 8/10 ©2022 ROHM Co., Ltd. All rights reserved 2022.2 - Rev.008 　　　　 [SLI-560x/SLA-560x/SLA560x series] [Data Sheet] ４．SOLDERING（Sn-3Ag-0.5Cu） 　(1) Please make soldering rapidly under the following temperature and time conditions. 　(2) Please avoid stress to LED lamp during soldering. 　(3) In case of double peak flow soldering, the temperature gap during 1st and 2nd soldering to be 　　less than 100 degree C. ＜Recommendable soldering conditions＞ SOLDERINGTEMP OPERATION TIME ARTIICLE Pre-heat Max. 100℃ 60sec Max. Soldering Dip Remarks － In case of double peak flow soldering, the operation Soldering Bath Soldering Iron Max. 265℃ 5sec Max. Max. 400℃ 3sec Max. time is counted from the beginning of 1st peak to the end of 2nd peak. The iron should not touch the LED’s body. ５．CLEANING 　In case of cleaning, some solvents may cause damage of resin or cause non-lighting failure, 　so please check the solvent before actual use. 　The recommendable cleaning solvent is alcoholic one such as isopropyl alcohol. ＜RECOMMENDABLE CLEANING CONDITIONS＞ METHOD CONDITIONS Temperature of solvent ：Max. 45℃ Cleaning by solvent Immersion time ：Max. 3min Ultrasonic out ：Max. 15W/Liter Cleaning by solvent Cleaning time ：Max. 3min ６．RECOMMENDABLE ROUND PATTERN 　　Round pattern depends on the material PCB, density and circuit arrangement. 　　Our recommendation is as follow : ±0.1 1.0 2.5 or 5.0 ±0.1 2.0 1.0 ＜3 lead pin type/2.0mm pitch> ±0.1 2.0 2.5 2.5 1.0 1.5 2.0 ＊Unit : mm ＊Lead types : □0.4mm □0.5mm 2.0 φ2.0 ■ATTENTION ON STORAGING 　Storage in dry box is most desirable, but if it is not possible, we recommend following conditions. ＜RECOMMENDABLE STORAGE CONDITIONS＞ Temperature Humidity ARTICLE Expiration Date CONDITIONS 5～30℃ Max.60%RH Within 1 year Poor storage conditions may cause some failure as bellow. 　(1) Lead pins may corrode if it is stored in the environment of high temperature and humidity 　　and lead to defective soldering. 　(2) In case of soldering after LED’s body absorb moisture highly, destruction or inferiority of 　　luminous intensity may occur. ＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿ www.rohm.com 9/10 ©2022 ROHM Co., Ltd. All rights reserved 2022.2 - Rev.008 [SLI-560x/SLA-560x/SLA560x series] 　　　　 [Data Sheet] ■APPLICATION METHOD １．Precaution for Drive System and Off Mode 　　　・Design the circuit without the electric load exceeding the ABSOLUTE MAXIMUM RATING that 　　　applies on the products. 　　　・If drive by constant voltage, it may cause current deviation of the LED and result in deviation of 　　　luminous intensity, so we recommend to drive by constant current. (Deviation of VF Value will 　　　cause deviation of current in LED.) ・Furthermore, for off mode, please do not apply voltage neither forward nor reverse. Especially, for the products with the Ag-paste used in the die bonding, there’s high possibility to cause electro migration and result in function failure. ２. Operation Life Span 　　　There’s possibility for intensity of light drop according to working conditions and environments 　　　 (applied current, surrounding temperature and humidity, corrosive gases ), please call our Sales 　　　staffs for inquiries about the concerned application below. 　　　(1) Longtime intensity of light life 　　　(2) On mode all the time ３. Usage 　　　The Product is LED. We are not responsible for the usage as the diode such as Protection Chip, Rectifier, Switching and so on. ■OTHERS １. Surrounding Gas 　　　Notice that if it is stored under the condition of acid gas (chlorine gas, sulfured gas) or alkali gas 　　　 (ammonia), it may result in low soldering ability (caused by the change in quality of the plating 　　　surface ) or optical characteristics changes (light intensity, chrominance) and change in quality of 　　　die bonding (Ag-paste) materials. All of the above will cause function failure of the products. 　　　Therefore, please pay attention to the storage environment for mounted product (concern the 　　　generated gas of the surrounding parts of the products and the atmospheric environment). ２. Electrostatic Damage 　　　The product is part of semiconductor and electrostatic sensitive, there’s high possibility to be 　　　damaged by the electrostatic discharge. 　　　Please take appropriate measures to avoid the static electricity from human body and earthing 　　setting of production equipment. The resistance values of electrostatic discharge (actual values) 　　are different varies with products, therefore, please call our Sales staffs for inquiries. ３. Electromagnetic Wave Applications with strong electromagnetic wave such as, IH cooker, will influence the reliability of LED, therefore please evaluate before using it. ＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿ www.rohm.com 10/10 ©2022 ROHM Co., Ltd. All rights reserved 2022.2 - Rev.008 Notice Notes 1) The information contained herein is subject to change without notice. 2) Before you use our Products, please contact our sales representative and verify the latest specifications. 3) Although ROHM is continuously working to improve product reliability and quality, semiconductors can break down and malfunction due to various factors. Therefore, in order to prevent personal injury or fire arising from failure, please take safety measures such as complying with the derating characteristics, implementing redundant and fire prevention designs, and utilizing backups and fail-safe procedures. ROHM shall have no responsibility for any damages arising out of the use of our Poducts beyond the rating specified by ROHM. 4) Examples of application circuits, circuit constants and any other information contained herein are provided only to illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. 5) The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM or any other parties. ROHM shall have no responsibility whatsoever for any dispute arising out of the use of such technical information. 6) The Products are intended for use in general electronic equipment (i.e. AV/OA devices, communication, consumer systems, gaming/entertainment sets) as well as the applications indicated in this document. 7) The Products specified in this document are not designed to be radiation tolerant. 8) For use of our Products in applications requiring a high degree of reliability (as exemplified below), please contact and consult with a ROHM representative : transportation equipment (i.e. cars, ships, trains), primary communication equipment, traffic lights, fire/crime prevention, safety equipment, medical systems, servers, solar cells, and power transmission systems. 9) Do not use our Products in applications requiring extremely high reliability, such as aerospace equipment, nuclear power control systems, and submarine repeaters. 10) ROHM shall have no responsibility for any damages or injury arising from non-compliance with the recommended usage conditions and specifications contained herein. 11) ROHM has used reasonable care to ensure the accuracy of the information contained in this document. However, ROHM does not warrants that such information is error-free, and ROHM shall have no responsibility for any damages arising from any inaccuracy or misprint of such information. 12) Please use the Products in accordance with any applicable environmental laws and regulations, such as the RoHS Directive. For more details, including RoHS compatibility, please contact a ROHM sales office. ROHM shall have no responsibility for any damages or losses resulting non-compliance with any applicable laws or regulations. 13) When providing our Products and technologies contained in this document to other countries, you must abide by the procedures and provisions stipulated in all applicable export laws and regulations, including without limitation the US Export Administration Regulations and the Foreign Exchange and Foreign Trade Act. 14) This document, in part or in whole, may not be reprinted or reproduced without prior consent of ROHM. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2015 ROHM Co., Ltd. All rights reserved. R1107 A Datasheet General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s representative. 3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. Notice – WE © 2015 ROHM Co., Ltd. All rights reserved. Rev.001