SLR-332VC3F

TYPE PRODUCTS Visual Light Emitting Diodes PAGE ／ SLR-332VR 1. CONSTRUCTION Red visual light emitting diodes featuring GaAsP packed with red diffused resin. 2. USAGE Power source for display unit. 3. DIMENSIONS See Figure.1 4. ABSOLUTE MAXIMUM RATINGS Power Dissipation Forward Current Peak Forward Current R e v e r s e Vo l t a g e Operating Temperature Storage Temperature (Ta=25℃) P D ・・・・・・・・・・・・ 60mW I F ・・・・・・・・・・・・ 20mA I F P ・・・・・・・・・・・・ 60mA ( Notes 1 ) V R ・・・・・・・・・・・・ 3V Topr ・・・・・・・・・・・・ －25℃～＋ 85℃ Tstg ・・・・・・・・・・・・ －30℃～＋100℃ ( Notes1 Duty 1/5 Pulse Width 1ms ) 5. ELECTRO－OPTICAL CHARACTERISTICS ( Ta=25℃) DISCRIPTION SYMBOL CONDITION MIN. TYP. MAX. UNITS Forward Voltage VF IF=10mA － 2.0 3.0 V Reverse Current IR VR=3V － － 10 μA Luminous Intensity IV IF=10mA 3.6 10 (28) mcd Peak Wave Length λP IF=10mA － 650 － nm Spectral Line Half Width △λ IF=10mA － 40 － nm ( 6. LUMINOUS CLASSIFICATION SYMBOL (Ta=25℃, IF=10mA) LUMINOUS CLASSIFICATION RANGE “K” ３．６ ～ ７．１ mcd “L” ５．６ ～ １１ mcd “M” ９．０ ～ １８ mcd “N” １４ ～ （２８） mcd ( ) : Reference Due to luminous intensity up, Intensity might shift. 7. PRODUCT WEIGHT Product weight per piece, approx 0.12grm. REV.： TSZ22111･05･002 C SPECIFICATION No.： SLR332 ) : Reference TYPE PRODUCTS Visual Light Emitting Diodes PAGE ／ SLR-332VC 1. CONSTRUCTION Red visual light emitting diodes featuring GaAsP packed with transparent red-colored resin. 2. USAGE Power source for display unit. 3. DIMENSIONS See Figure.1 4. ABSOLUTE MAXIMUM RATINGS Power Dissipation Forward Current Peak Forward Current R e v e r s e Vo l t a g e Operating Temperature Storage Temperature (Ta=25℃) P D ・・・・・・・・・・・・ 60mW I F ・・・・・・・・・・・・ 20mA I F P ・・・・・・・・・・・・ 60mA ( Notes 1 ) V R ・・・・・・・・・・・・ 3V Topr ・・・・・・・・・・・・ －25℃～＋ 85℃ Tstg ・・・・・・・・・・・・ －30℃～＋100℃ ( Notes1 Duty 1/5 Pulse Width 1ms ) 5. ELECTRO－OPTICAL CHARACTERISTICS ( Ta=25℃) DISCRIPTION SYMBOL CONDITION MIN. TYP. MAX. UNITS Forward Voltage VF IF=10mA － 2.0 3.0 V Reverse Current IR VR=3V － － 10 μA Luminous Intensity IV IF=10mA 3.6 10 (28) mcd Peak Wave Length λP IF=10mA － 650 － nm Spectral Line Half Width △λ IF=10mA － 40 － nm ( 6. LUMINOUS CLASSIFICATION SYMBOL (Ta=25℃, IF=10mA) LUMINOUS CLASSIFICATION RANGE “K” ３．６ ～ ７．１ mcd “L” ５．６ ～ １１ mcd “M” ９．０ ～ １８ mcd “N” １４ ～ （２８） mcd ( ) : Reference Due to luminous intensity up, Intensity might shift. 7. PRODUCT WEIGHT Product weight per piece, approx 0.12grm. REV.： TSZ22111･05･002 C SPECIFICATION No.： SLR332 ) : Reference TYPE PRODUCTS Visual Light Emitting Diodes PAGE ／ SLR-332DU 1. CONSTRUCTION Orange visual light emitting diodes featuring GaAsP packed with orange diffused resin. 2. USAGE Power source for display unit. 3. DIMENSIONS See Figure.1 4. ABSOLUTE MAXIMUM RATINGS Power Dissipation Forward Current Peak Forward Current R e v e r s e Vo l t a g e Operating Temperature Storage Temperature (Ta=25℃) P D ・・・・・・・・・・・・ 60mW I F ・・・・・・・・・・・・ 20mA I F P ・・・・・・・・・・・・ 60mA ( Notes 1 ) V R ・・・・・・・・・・・・ 3V Topr ・・・・・・・・・・・・ －25℃～＋ 85℃ Tstg ・・・・・・・・・・・・ －30℃～＋100℃ ( Notes1 Duty 1/5 Pulse Width 1ms ) 5. ELECTRO－OPTICAL CHARACTERISTICS ( Ta=25℃) DISCRIPTION SYMBOL CONDITION MIN. TYP. MAX. UNITS Forward Voltage VF IF=10mA － 2.0 3.0 V Reverse Current IR VR=3V － － 10 μA Luminous Intensity IV IF=10mA 3.6 10 (28) mcd Peak Wave Length λP IF=10mA － 610 － nm Spectral Line Half Width △λ IF=10mA － 40 － nm ( 6. LUMINOUS CLASSIFICATION SYMBOL (Ta=25℃, IF=10mA) LUMINOUS CLASSIFICATION RANGE “K” ３．６ ～ ７．１ mcd “L” ５．６ ～ １１ mcd “M” ９．０ ～ １８ mcd “N” １４ ～ （２８） mcd ( ) : Reference Due to luminous intensity up, Intensity might shift. 7. PRODUCT WEIGHT Product weight per piece, approx 0.12grm. REV.： TSZ22111･05･002 C SPECIFICATION No.： SLR332 ) : Reference TYPE PRODUCTS Visual Light Emitting Diodes PAGE ／ SLR-332DC 1. CONSTRUCTION Orange visual light emitting diodes featuring GaAsP packed with transparent orange-colored resin. 2. USAGE Power source for display unit. 3. DIMENSIONS See Figure.1 4. ABSOLUTE MAXIMUM RATINGS Power Dissipation Forward Current Peak Forward Current R e v e r s e Vo l t a g e Operating Temperature Storage Temperature (Ta=25℃) P D ・・・・・・・・・・・・ 60mW I F ・・・・・・・・・・・・ 20mA I F P ・・・・・・・・・・・・ 60mA ( Notes 1 ) V R ・・・・・・・・・・・・ 3V Topr ・・・・・・・・・・・・ －25℃～＋ 85℃ Tstg ・・・・・・・・・・・・ －30℃～＋100℃ ( Notes1 Duty 1/5 Pulse Width 1ms ) 5. ELECTRO－OPTICAL CHARACTERISTICS ( Ta=25℃) DISCRIPTION SYMBOL CONDITION MIN. TYP. MAX. UNITS Forward Voltage VF IF=10mA － 2.0 3.0 V Reverse Current IR VR=3V － － 10 μA Luminous Intensity IV IF=10mA 5.6 16 (45) mcd Peak Wave Length λP IF=10mA － 610 － nm Spectral Line Half Width △λ IF=10mA － 40 － nm ( 6. LUMINOUS CLASSIFICATION SYMBOL (Ta=25℃, IF=10mA) LUMINOUS CLASSIFICATION RANGE “L” ５．６ ～ １１ mcd “M” ９．０ ～ １８ mcd “N” １４ ～ ２８ mcd “P” ２２ ～ （４５） mcd ( ) : Reference Due to luminous intensity up, Intensity might shift. 7. PRODUCT WEIGHT Product weight per piece, approx 0.12grm. REV.： TSZ22111･05･002 C SPECIFICATION No.： SLR332 ) : Reference TYPE PRODUCTS Visual Light Emitting Diodes PAGE ／ SLR-332YC 1. CONSTRUCTION Yellow visual light emitting diodes featuring GaAsP packed with transparent yellow-colored resin. 2. USAGE Power source for display unit. 3. DIMENSIONS See Figure.1 4. ABSOLUTE MAXIMUM RATINGS Power Dissipation Forward Current Peak Forward Current R e v e r s e Vo l t a g e Operating Temperature Storage Temperature (Ta=25℃) P D ・・・・・・・・・・・・ 60mW I F ・・・・・・・・・・・・ 20mA I F P ・・・・・・・・・・・・ 60mA ( Notes 1 ) V R ・・・・・・・・・・・・ 3V Topr ・・・・・・・・・・・・ －25℃～＋ 85℃ Tstg ・・・・・・・・・・・・ －30℃～＋100℃ ( Notes1 Duty 1/5 Pulse Width 1ms ) 5. ELECTRO－OPTICAL CHARACTERISTICS ( Ta=25℃) DISCRIPTION SYMBOL CONDITION MIN. TYP. MAX. UNITS Forward Voltage VF IF=10mA － 2.1 3.0 V Reverse Current IR VR=3V － － 10 μA Luminous Intensity IV IF=10mA 3.6 10 (28) mcd Peak Wave Length λP IF=10mA － 585 － nm Spectral Line Half Width △λ IF=10mA － 40 － nm ( 6. LUMINOUS CLASSIFICATION SYMBOL (Ta=25℃, IF=10mA) LUMINOUS CLASSIFICATION RANGE “K” ３．６ ～ ７．１ mcd “L” ５．６ ～ １１ mcd “M” ９．０ ～ １８ mcd “N” １４ ～ （２８） mcd ( ) : Reference Due to luminous intensity up, Intensity might shift. 7. PRODUCT WEIGHT Product weight per piece, approx 0.12grm. REV.： TSZ22111･05･002 C SPECIFICATION No.： SLR332 ) : Reference TYPE PRODUCTS Visual Light Emitting Diodes PAGE ／ SLR-332MG 1. CONSTRUCTION Yellow Green visual light emitting diodes featuring GaP packed with green diffused resin. 2. USAGE Power source for display unit. 3. DIMENSIONS See Figure.1 4. ABSOLUTE MAXIMUM RATINGS (Ta=25℃) P D ・・・・・・・・・・・・ 75mW I F ・・・・・・・・・・・・ 25mA I F P ・・・・・・・・・・・・ 60mA ( Notes 1 ) V R ・・・・・・・・・・・・ 3V Topr ・・・・・・・・・・・・ －25℃～＋ 85℃ Tstg ・・・・・・・・・・・・ －30℃～＋100℃ ( Notes1 Duty 1/5 Pulse Width 1ms ) Power Dissipation Forward Current Peak Forward Current R e v e r s e Vo l t a g e Operating Temperature Storage Temperature 5. ELECTRO－OPTICAL CHARACTERISTICS ( Ta=25℃) DISCRIPTION SYMBOL CONDITION MIN. TYP. MAX. UNITS Forward Voltage VF IF=10mA － 2.1 3.0 V Reverse Current IR VR=3V － － 10 μA Luminous Intensity IV IF=10mA 5.6 16 (45) mcd Peak Wave Length λP IF=10mA － 563 － nm Spectral Line Half Width △λ IF=10mA － 40 － nm ( ) : Reference 6. LUMINOUS CLASSIFICATION SYMBOL (Ta=25℃, IF=10mA) LUMINOUS CLASSIFICATION RANGE “L” ５．６ ～ １１ mcd “M” ９．０ ～ １８ mcd “N” １４ ～ ２８ mcd “P” ２２ ～ （４５） mcd ( ) : Reference Due to luminous intensity up, Intensity might shift. 7. PRODUCT WEIGHT Product weight per piece, approx 0.12grm. REV.： TSZ22111･05･002 D SPECIFICATION No.： SLR332 TYPE PRODUCTS Visual Light Emitting Diodes PAGE ／ SLR-332MC 1. CONSTRUCTION Yellow Green visual light emitting diodes featuring GaP packed with transparent green-colored resin. 2. USAGE Power source for display unit. 3. DIMENSIONS See Figure.1 4. ABSOLUTE MAXIMUM RATINGS (Ta=25℃) P D ・・・・・・・・・・・・ 75mW I F ・・・・・・・・・・・・ 25mA I F P ・・・・・・・・・・・・ 60mA ( Notes 1 ) V R ・・・・・・・・・・・・ 3V Topr ・・・・・・・・・・・・ －25℃～＋ 85℃ Tstg ・・・・・・・・・・・・ －30℃～＋100℃ ( Notes1 Duty 1/5 Pulse Width 1ms ) Power Dissipation Forward Current Peak Forward Current R e v e r s e Vo l t a g e Operating Temperature Storage Temperature 5. ELECTRO－OPTICAL CHARACTERISTICS ( Ta=25℃) DISCRIPTION SYMBOL CONDITION MIN. TYP. MAX. UNITS Forward Voltage VF IF=10mA － 2.1 3.0 V Reverse Current IR VR=3V － － 10 μA Luminous Intensity IV IF=10mA 5.6 16 (45) mcd Peak Wave Length λP IF=10mA － 563 － nm Spectral Line Half Width △λ IF=10mA － 40 － nm ( ) : Reference 6. LUMINOUS CLASSIFICATION SYMBOL (Ta=25℃, IF=10mA) LUMINOUS CLASSIFICATION RANGE “L” ５．６ ～ １１ mcd “M” ９．０ ～ １８ mcd “N” １４ ～ ２８ mcd “P” ２２ ～ （４５） mcd ( ) : Reference Due to luminous intensity up, Intensity might shift. 7. PRODUCT WEIGHT Product weight per piece, approx 0.12grm. REV.： TSZ22111･05･002 D SPECIFICATION No.： SLR332 PRODUCTS Visual Light Emitting Diodes TYPE PAGE SLR-332 Series 【Figure.1 DIMENSIONS(Bulk drawing)】 φ4±0.3 φ3.2 4.3±0.3 (1.0) 1.0MAX 3.3 R1.5 4-0.5+0.2 -0.1 2.5±1.0 24.0MIN 2-□0.4±0.1 Tolerance : ±0.2 CATHODE 2.5 （Unit : mm） （bottom side lead dimension) REV.： TSZ22111･05･002 C SPECIFICATION No.： SLR332 ／ TYPE PRODUCTS Visual Light Emitting Diodes PAGE ／ SLR-332 Series 【Taping : T32】 △ｈ A1 P2 P A2 △P W W0 L W1 H （W2) d PF D0 F t PO ITEM SYMBOL Body diameter Body height Pitch of component Feed hole pitch Hole center to component center Hole pitch tolerance accumulation Lead wire thickness Lead to lead distance Clinch height Ｗ Tape width Ｗ0 Ｗ1 Ｗ2 ｔ Δｈ ΔＰ Ｌ ＰF Ｄ0 Hold down tape width Hole position Hole down tape position Tape thickness Component alignment (1) Component alignment (2) Length of snipped lead Feed hole center to lead center Feed hole diameter REV.： TSZ22111･05･002 Ａ1 Ａ2 Ｐ Ｐ0 Ｐ2 Ｐ20 ｄ Ｆ Ｈ C SPECIFICATION (Unit : mm) φ３．２±０．２ ４．３±０．３ １２．７±１．０ １２．７±０．３ ６．３５±０．４ For 20 pitches 1.0MAX □０．４±０．１ ※ ２．５±０．８ ２１．５±１．０ １８．０ +1.0 -0.5 13.0±0.3 , 10.0±0.3 ９．０±０．５ ３．０MAX ０．７±０．２ ０±２．０ ０±１．０ １１．０MAX ５．１±０．８ φ４．０±０．２ ※Except flush SPECIFICATION No.： SLR332 PRODUCTS Visual Light Emitting Diodes TYPE PAGE SLR-332 Series 【STRUCTURE･MATERIAL】 No. APPELLATION MATERIAL ① Lead Frame Lead Iron Copper + Silver Plating Solder Dip ② Die Bond Ag Paste ③ LED Chip M, P : GaP V, D, Y : GaAsP ④ Bonding Wire Gold ⑤ Resin Epoxy Resin REV.： TSZ22111･05･002 C SPECIFICATION No.： SLR332 ／ PRODUCTS Visual Light Emitting Diodes TYPE PAGE SLR-332 Series 【PACKAGING REQUIREMENTS】 1.PACKGING 1.1 The tape is folded over across a pitch of 25 pieces or 26 pieces. 1.2 Tape leader and tape end leave 10 blank part positions. 1.3 Any reject units are clipped or cut off in the permissible location specified in the drawing. 1.4 No more than three consecutive blank and 10 pieces out of consecutive 1,000 pieces are permitted. However. 2.CARTON Ｃ Ｂ Ａ （Unit：mm） Ａ １５８ ± ７ Ｂ ４８ ± ７ Ｃ ３４０ ± ７ 3.QUANTITY 2,000pcs/Box REV.： TSZ22111･05･002 C SPECIFICATION No.： SLR332 ／ TYPE PRODUCTS Visual Light Emitting Diodes PAGE SLR-332 Series 4.TAPE TRAVEL INDICATION Indication “C” on the four points where cathode lead leaves tape first, and indication “A” on the four points where anode lead leaves tape first. C A Window (1 or 2) Label 5.TAPE DEVICE RETENTION PARAMETERS 5.1 Horizontal direction H=20mm Stable F=1N｛round 102gf｝Applied for 3±1sec 5.2 Vertical direction H=20mm Stable F=0.7N｛round 71.4gf｝Applied for 3±1sec REV.： TSZ22111･05･002 D SPECIFICATION No.： SLR332 ／ TYPE PRODUCTS Visual Light Emitting Diodes 5.3 PAGE ／ SLR-332 Series Adhesiveness ･More than 5N{round 510gf} Lead should not come off or be misaligned. Stable Force on to arrow direction. 6.ANNEX 6.1 No more three consecutive blank space permitted. 6.2 Tape jointing, in case of tape end or cutting, is done with jointing tape or sticky tape. The jointing area’s thickness is 1.5mm max and strength is more than 10N {round 1.02kgf}. 6.3 Permissible misalignment is 1.0mm max across a pitch of 20 holes. 20 pitches ａ REV.： TSZ22111･05･002 C SPECIFICATION No.： SLR332 TYPE PRODUCTS Visual Light Emitting Diodes PAGE ／ SLR-332 Series 2.MARKING The following information shall be described on a box label: ROHM type number, packaging quantity, luminous intensity rank, lot number etc. 【FORMER LABEL SPECIFICATION】 Luminous Intensity Rank Type ＳＬＲ－３３２ＶＣＴ３２　　　　　Ｌ 　 Ｆ 　 　 ２ ,０ ０ ０ ｐ ｃ ｓ 　 １ ２ ０ ３ 　 ０ ０ ０ １ ２ Ｗ FOR ROHM ONLY Country of origin Interoffice administration code Customers part No. etc. “F” means Pb-free, Quantity, Then Lot No. displayed NOTE） Indicates bar code expressed by code 39 indicates Pb-free Products. 【EXAMPLE OF LOT NO. MARKING】 １２ ０３ ０００１２ Ｗ Production facility sigh ( Refer the manufactory list ) Serial number of lot Production week Production year REV.： TSZ22111･05･002 C SPECIFICATION No.： SLR332 PRODUCTS Visual Light Emitting Diodes TYPE PAGE ／ LAMP Series 【ATTENTION POINTS IN HANDLING】 Visual light emitting diode does not contain reinforcement materials such as glass fillers. Therefore if sudden thermal and mechanical shock are given, destruction or inferiority of luminous intensity may occur. Please take care of the handling. ■FIXATION METHOD 1. ATTENTION POINTS (1) Please do not give excessive heat over storage temperature to resin. In case that the product has to be heated in oven for the glue fixing of surface mount pats, this LED should be mounted after the glue fixing. (2) Please avoid stress to resin at high temperature. 2. TERMINATION PROCESSING (1) In case of termination processing, please fix the termination (2) Processing position, and process the reverse side of LED body. If stress is given during processing, It may cause non-lighting failure. (3) Please process before soldering. ＜No good＞ ＜Good＞ To be fixed To be fixed 3. ASSEMBLY ON PC BOARD (1) In case of soldering on PCB, If the operation is done with stress, it may cause non-lighting failure during soldering or using. Please design the through-holes of PCB suitable for lead pins space or lead pins space after forming to avoid the physical stress on resin. ＜Good＞ ＜Good＞ ＜No good＞ ＜2 lead pins type＞ ＜3 lead pins type＞ (2) Using spacer between LED’s body and PCB is recommended. In case of direct mount on PCB(SLR/SLI-343 series), please take care about clinch of led pins to avoid the remained stress and solder heat stress. Enough evaluation is requested before deciding assembly and soldering conditions. Please consult with us if any problems in the evaluation stage. ＜3 lead pin type＞ ＜2 lead pin type＞ Min.15° Min.45° Die bonding side REV.： TSZ22111･05･002 Min.45° 001 Min.45° Min.15° Die bonding side SPECIFICATION No.： LMP-N002 PRODUCTS Visual Light Emitting Diodes TYPE PAGE ／ LAMP Series 4. SOLDERING（Sn-3Ag-0.5Cu） (1) Please make soldering rapidly under the following temperature and time conditions. (2) Please avoid stress to LED lamp during soldering. (3) In case of double peak flow soldering, the temperature gap during 1st and 2nd soldering to be less than 100 degree C. SOLDERING OPERATION ARTIICLE TEMP TIME Soldering Dip Pre-heat Max. 100℃ 60sec Max. Soldering Bath Max. 265℃ 5sec Max. Max. 400℃ 3sec Max. Soldering Iron Remarks In case of double peak flow soldering, the operation time is counted from the beginning of 1st peak to the end of 2nd peak. The iron should not touch the LED’s body. 5. CLEANING In case of cleaning, some solvents may cause damage of resin or cause non-lighting failure, so please check the solvent before actual use. The recommendable cleaning solvent is alcoholic one such as isopropyl alcohol. ＜RECOMMENDABLE CLEANING CONDITIONS＞ METHOD CONDITIONS Temperature of solvent ：Max. 45℃ Cleaning by solvent Immersion time ：Max. 3min Ultrasonic out ：Max. 15W/Liter Cleaning by solvent Cleaning time ：Max. 3min 6. RECOMMENDABLE ROUND PATTERN Round pattern depends on the material PCB, density and circuit arrangement. Our recommendation is as follow : ±0.1 2.5 1.0 ±0.1 2.0 1.0 ＜3 lead pin type/2.0mm pitch> ±0.1 2.0 1.5 2.0 2.5 or 1.0 2.0 ＊Unit : mm 2.0 2.5 ＊Lead types : □0.4mm φ2.0 □0.5mm ■ATTENTION ON STORAGING Storage in dry box is most desirable, but if it is not possible, we recommend following conditions. ＜RECOMMENDABLE STORAGE CONDITIONS＞ ARTICLE Temperature Humidity CONDITIONS Max.60%RH 5～30℃ Expiration Date Within 1 year Poor storage conditions may cause some failure as bellow. (1) Lead pins may corrode if it is stored in the environment of high temperature and humidity and lead to defective soldering. (2) In case of soldering after LED’s body absorb moisture highly, destruction or inferiority of luminous intensity may occur. REV.： TSZ22111･05･002 001 SPECIFICATION No.： LMP-N002 PRODUCTS Visual Light Emitting Diodes TYPE PAGE LAMP Series ／ ■APPLICATION METHOD 1. Precaution for Drive System and Off Mode ・Design the circuit without the electric load exceeding the ABSOLUTE MAXIMUM RATING that applies on the products. ・If drive by constant voltage, it may cause current deviation of the LED and result in deviation of luminous intensity, so we recommend to drive by constant current. (Deviation of VF Value will cause deviation of current in LED.) ・Furthermore, for off mode, please do not apply voltage neither forward nor reverse. Especially, for the products with the Ag-paste used in the die bonding, there’s high possibility to cause electro migration and result in function failure. 2. Operation Life Span There’s possibility for intensity of light drop according to working conditions and environments (applied current, surrounding temperature and humidity, corrosive gases ), please call our Sales staffs for inquiries about the concerned application below. (1) Longtime intensity of light life (2) On mode all the time 3. Usage The Product is LED. We are not responsible for the usage as the diode such as Protection Chip, Rectifier, Switching and so on. ■OTHERS 1. Surrounding Gas Notice that if it is stored under the condition of acid gas (chlorine gas, sulfured gas) or alkali gas (ammonia), it may result in low soldering ability (caused by the change in quality of the plating surface ) or optical characteristics changes (light intensity, chrominance) and change in quality of die bonding (Ag-paste) materials. All of the above will cause function failure of the products. Therefore, please pay attention to the storage environment for mounted product (concern the generated gas of the surrounding parts of the products and the atmospheric environment). 2. Electrostatic Damage The product is part of semiconductor and electrostatic sensitive, there’s high possibility to be damaged by the electrostatic discharge. Please take appropriate measures to avoid the static electricity from human body and earthing setting of production equipment. The resistance values of electrostatic discharge (actual values) are different varies with products, therefore, please call our Sales staffs for inquiries. 3. Electromagnetic Wave Please concern the influence on LED in case of application with strong electromagnetic wave such as IH (Induction heating). REV.： TSZ22111･05･002 001 SPECIFICATION No.： LMP-N002