SML-012DT

SURFACE MOUNT LED LAMPS High Brightness Type Chip LEDs with reflector SML-01＊ Series Blue Package Size （mm） GaN on SiC 428nm 468nm InGaN on SiC 525nm 590nm Green Yellow Orange AlGaInP on GaAs 611nm 630nm Red 3216 (1206) 3.0×2.0 t=1.3 SML010BAT SML011BBT SML012BCT SML011EBT SML012ECT SML-011YT SML-012YT SML-011DT SML-012DT SML-011UT SML-012UT Note) "-" will be taken out for emitting color B/E series. ■ Absolute Maximum Ratings（Ta=25℃） Peak Reverse Operating Stotage Power Forward forward Emitting dissipation current voltage temperature temperature current color PD IF VR Topr Tstg ＊IFP （mW） （mA） （V） （°C） （°C） （mA） 94 Blue 84 Green Yellow Orange Red 75 30 100 5 -40 to +100 -40 to +100 20 100 -30 to +85 -40 to +100 70 ■ External Dimensions（Unit：mm） 3.0 2.3 ＋0.2 1.3 −0.1 0.3 0.5 Part No. SML010BAT SML011BBT SML012BCT SML011EBT SML012ECT SML-011YT SML-012YT SML-011DT SML-012DT SML-011UT SML-012UT 2.0 1.6 Cathode mark 2−R0.3 1.7 Terminal ＊ IFP measured under duty ≦1/10,1kHz. 1.6 ■ Electrical Optical Characteristics（Ta=25℃） Forward voltage VF Typ. (V) 3.8 3.5 IF (mA) Tolerance:±0.1 Part No. Resin Color Reverse current IR Max. (µA) VR (V) Light wavelength Peak Half-wave λp ∆λ Typ. (nm) 428 468 523 518 Typ. (nm) 65 26 36 35 15 17 18 IF (mA) Brightness IV Min. ( mcd) ■ Directivity X’ Y’ 0° 30° 30° SML010BAT SML011BBT SML012BCT SML011EBT SML012ECT SML-011YT SML-012YT SML-011DT SML-012DT SML-011UT SML-012UT 100 Transparent Clear 3.8 20 2.0 10 5 20 590 611 630 3.6 22 36 56 140 22 36 22 36 22 36 Typ. IF (mcd) (mA) 9 36 100 140 360 20 63 100 63 140 63 100 60° 60° 90° 100 50 0 50 90° 100 Relative brightness (%) (Typ.) ■ Recommemded Pad Layout 1.6 ■ Packaging Spacifications（Unit：mm） Tape Spacifications：T86〈2,500pcs／reel〉 Reel Spacifications Lavel Position 1.45 Feeding direction 4 2 1.75 3.5 3.4 5.5 8 φ1.5 1.45 1.5 φ13 1.6 2.4 （Unit：mm） 0.5 φ60 φ180 The recommended thickness of the screen mask for soldering is between 100 and 200μm. The hole size of the screen mask should be same as the recommended land pattern or smaller. 11.4 SURFACE MOUNT LED LAMPS ■ Electrical Characteristic Curves Forward Current - Forward Voltage SML-010BAT 100.0 Ta＝25℃ SML-011YT 100.0 Ta＝25℃ SML-011BBT SML-012BCT SML-011EBT SML-012ECT SML-012YT SML-011DT FORWARD CURRENT : IF (mA) FORWARD CURRENT : (mA) SML-012DT SML-011UT SML-012UT 10.0 10.0 1.0 2.8 3.0 3.2 3.4 3.6 3.8 FORWARD VOLTAGE : VF (V) 4.0 1.0 1.0 1.5 2.0 2.5 FORWARD VOLTAGE : (V) 3.0 Relative Luminous Intensity - Case Temperature SML-010BAT 1.6 SML-011YT 1.6 SML-011BBT SML-012BCT SML-011EBT RELATIVE LUMINOUS INTENSITY IF=20mA SML-012YT IF＝20mA RELATIVE LUMINOUS INTENSITY 1.4 1.2 1.0 0.8 0.6 0.4 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 1.4 1.2 1.0 0.8 0.6 0.4 −30 −20 −10 0 10 20 30 40 50 60 70 80 90 100 SML-011DT SML-012DT SML-011UT SML-012UT SML-012ECT CASE TEMPERATURE : Tc (℃) CASE TEMPERATURE : Tc (℃) Relative Luminous Intensity - Forward Current SML-010BAT 150 SML-011YT 250 f＝1kHz SML-011BBT RELATIVE LUMINOUS INTENSITY SML-012YT DC RELATIVE LUMINOUS INTENSITY SML-012BCT SML-011EBT 100 SML-011DT SML-012DT 200 DF＝50％ SML-012ECT SML-011UT SML-012UT 150 100 20％ 15％ 50 10％ 0 5％ 50 0 0 10 20 30 0 IF : mA 10 20 30 40 50 60 PEAK FORWARD CURRENT : (mA) Ratio of Maximum Tolerable Peak Current - Pulse Duration SML-010BAT SML-011BBT 200Hz 100Hz 10kHz 2kHz 1kHz 10 SML-011YT SML-012YT SML-011DT 500Hz 5kHz SML-012BCT 2kHz 1kHz 200Hz 100Hz 50kHz 20kHz 10kHz 5 SML-011EBT SML-012ECT IFP Max／IF Max SML-012DT SML-011UT SML-012UT IFP Max／IF Max 3.5 3.3 1 1 10 100 1000 10000 1 1 10 100 1000 10000 PULSE DURATION : Tw (μs) PULSE DURATION : Tw (μs) Derating SML010BAT MAXIMUM FORWARD CURRENT : IF Max. (mA) 30 SML-011YT MAXIMUM FORWARD CURRENT : IF Max. (mA) 30 SML011BBT SML012BCT SML011EBT SML-012YT SML-011DT SML-012DT 20 SML012ECT 20 SML-011UT SML-012UT 10 10 0 -20 -10 0 10 20 30 40 50 60 70 80 90 100 AMBIENT TEMPERATURE : Ta (℃) 0 0 10 20 30 40 50 60 70 80 90 100 AMBIENT TEMPERATURE : Ta (℃) Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1