SML-020MLTT87

Dual-Color Chip LEDs with Reflector 1210 Standard Type SML-020 Series Emitting Color Part No. Material Green(Yellowish Green) Red GaP GaAIAs on GaAs Package Size(mm) SML-020MLT 3025(1210) 3.0×2.5(t=1.3) Absolute Maximum Ratings (Ta=25∞C) (mW) SML-020MLT :Duty Green (Yellowish Green) Red 60 25 60 30 75 4 -30 to +85 3.0 1.3 2.3 0.5 Red 2.1 Part No. Peak Forward Reverse Operating Storage forward current voltage temperature temperature current IF VR Topr Tstg IFP (mA) (V) (°C) (°C) (mA) 2.5 Power Emitting dissipation color PD Dimensions (Unit:mm) Green -40 to +85 Cathode mark LED Die 1/5, pulse width 1ms. Electrical Optical Characteristics (Ta=25∞C) Part No. Resin Color Typ. (V) SML-020MLT IF (mA) Max. (µA) VR (V) 20 100 4 Transparent 2.2 Colorless 1.75 Light wavelength Peak Half-wave λp ∆λ Typ. (nm) Typ. (nm) 570 40 660 25 0.8 Reverse current IR Brightness IV 3 IF (mA) 20 2 1 4 3 2 1.5 Forward voltage VF Green 1 Min. Typ. IF ( mcd) (mcd) (mA) 20 20 9.0 16 1.0 Terminal 4 Red Tolerance:±0.2 Directivity (Typ.) Angular Displacement (deg) Green X Red 0° Y 30° 30° Green Red 60° 60° 90° 100 50 0 90° 100 50 RELATIVE LUMINOUS INTENSITY (%) Red X’ Angular Displacement (deg) 0° Y’ 30° Green, Red 30° Green 60° 60° 90° 100 50 0 50 90° 100 RELATIVE LUMINOUS INTENSITY (%) Recommended Pad Layout Packaging Specifications (Unit:mm) Tape Specifications:T86 1.05 0.6 1.05 Reel Specifications Tolerance:±0.2 φ 180 −30 φ 60 +10 φ 13 1.75±0.1 5.5 3.4 2.9 0 to 0.5 (Unit:mm) The recommended thickness of the screen mask for soldering is between 100 and 150µm. The hole size of the screen mask should be same as the recommended land pattern or smaller. 8 φ 1.5 +0.1 0 1.7 1.0 2±0.05 3.5±0.05 1.7 Feeding direction 4±0.1 1.6 Label Position 11.4±1 Tolerance:±0.2 Rev.C Electrical Characteristic Curves Forward Current - Forward Voltage Ta=25°C ------- 1.6 SML-020MLT IF=20mA RELATIVE LUMINOUS INTENSITY FORWARD CURRENT : IF (mA) 50 Relative Luminous Intensity - Case Temperature SML-020ML 10 1.0 1.4 ------- SML-020MLT SML-020MLT 1.2 1.0 0.8 0.6 0.1 0.4 1.5 2.0 2.5 3.0 -20-10 0 10 20 30 40 50 60 70 80 FORWARD VOLTAGE : VF (V) CASE TEMPERATURE : Tc (°C) Relative Luminous Intensity - Forward Current 3.0 Ta=25°C 2.5 2.0 1.5 1.0 0.5 0 0 10 20 30 40 50 Ta=25°C RELATIVE LUMINOUS INTENSITY RELATIVE LUMINOUS INTENSITY 3.0 ---- SML-020MLT ---- SML-020MLT ---- SML-020MLT ---- SML-020MLT 2.5 2.0 1.5 1.0 0.5 0 0 60 PEAK FORWARD CURRENT : IF peak (mA) 10 20 30 40 50 60 PEAK FORWARD CURRENT : IF peak (mA) 2.4 1 5 10 20 50 102 103 104 PULSE DURATION : Tw (µs) 100Hz 200Hz 500Hz 1kHz 2kHz 5kHz 10kHz 20kHz 5 50kHz RATIO of MAXIMUM TOLERABLE PEAK CURRENT IF peak Max. IF Max. to MAXIMUM TOLERABLE DC CURRENT 100Hz 200Hz 500Hz 1kHz 2kHz 5kHz 10kHz 20kHz 5 50kHz RATIO of MAXIMUM TOLERABLE PEAK CURRENT IF peak Max. IF Max. to MAXIMUM TOLERABLE DC CURRENT Ratio of Maximum Tolerable Peak Current - Pulse Duration 2.5 1 5 10 20 50 102 103 104 PULSE DURATION : Tw (µs) MAXIMUM FORWARD CURRENT : IF Max. (mA) Derating ------- 30 SML-020MLT SML-020MLT 20 10 0 0 10 20 30 40 50 60 70 80 90 AMBIENT TEMPERATURE : Ta (°C) Rev.C Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1