SML-210PT

SURFACE MOUNT LED LAMPS Standard Type Mini-molded chip LEDs SML-210 Series Pure Green Package Size （mm） GaP 555nm 570nm Green Yellow Orange Red GaAlAs on GaAs 650nm 660nm           GaAsP on GaP 585nm 610nm 2012 (0805) 2.0x1.25 t=0.8 SML-210PT SML-210MT SML-210YT SML-210DT SML-210VT SML-210LT ■ Absolute Maximum Ratings（Ta=25℃） Peak Reverse Operating Stotage Power Forward forward Emitting dissipation current voltage temperature temperature current color PD IF VR Topr Tstg ＊IFP （mW） （mA） （V） （°C） （°C） （mA） Pure Green Green Yellow Orange Red Red 75 30 75 70 25 60 4 -30 to +85 -40 to +85 ■ External Dimensions（Unit：mm） 2.0 ＋0.2 0 1.4 Part No. SML-210PT SML-210MT SML-210YT SML-210DT SML-210VT SML-210LT 1.25 Cathode mark 1.2 ＊IFP measured under duty ≦1/ 5,pulse width ≦1ms. Terminal ■ Electrical Optical Characteristics（Ta=25℃） Forward voltage VF Typ. (V) SML-210PT SML-210MT SML-210YT SML-210DT SML-210VT SML-210LT 2.2 IF (mA) Part No. Resin Color Reverse current IR Max. (µA) VR (V) Light wavelength Peak Half-wave λp ∆λ Typ. (nm) 555 570 585 610 650 660 25 40 Typ. (nm) IF (mA) Brightness IV Min. ( mcd) Tolerance:±0.1 Typ. IF (mcd) (mA) 4 16 6.3 4 10 20 ■ Directivity X’ Y’ 1.4 3.6 20 2.2 1.4 3.6 0° 30° 30° Transparent Clear 2.1 2.0 1.75 20 100 4 0.25 0.8 60° 60° 90° 100 50 0 50 90° 100 Relative brightness (%) (Typ.) ■ Recommemded Pad Layout ■ Packaging Spacifications（Unit：mm） Tape Spacifications：T86〈3,000pcs／reel〉 Reel Spacifications 1.1 Lavel Position 1.25 Feeding direction 4 2 1.75 3.5 2.5 5.5 8 φ1.5 1.25 1.1 φ13 1.0 1.7 （Unit：mm） 0.5 φ60 φ180 The recommended thickness of the screen mask for soldering is between 100 and 200μm. The hole size of the screen mask should be same as the recommended land pattern or smaller. 11.4 SURFACE MOUNT LED LAMPS ■ Electrical Characteristic Curves Forward Current - Forward Voltage 50 FORWARD CURRENT : IF (mA) 20 10 5.0 2.0 1.0 0.5 0.2 0.1 1.5 2.0 2.5 3.0 FORWARD VOLTAGE : VF (V) Ta=25℃ Relative Luminous Intensity - Case Temperature SML-210PT SML-210MT SML-210YT SML-210DT SML-210VT SML-210LT RELATIVE LUMINOUS INTENSITY 1.6 IF=20mA 1.4 SML-210PT SML-210MT SML-210YT 1.2 1.0 0.8 0.6 0.4 −20 0 20 40 SML-210DT SML-210VT SML-210LT 60 80 CASE TEMPERATURE : Tc (℃) Relative Luminous Intensity - Forward Current 3.0 RELATIVE LUMINOUS INTENSITY f=1kHz 2.5 DC 2.0 1.5 1.0 20% 0.5 0 0 15% 10% 5% 10 20 30 40 50 60 DF=50% SML-210PT SML-210MT SML-210YT SML-210DT SML-210VT RELATIVE LUMINOUS INTENSITY 3.0 f=1kHz 2.5 2.0 1.5 1.0 20% 0.5 0 0 15% 10% 5% 10 20 30 40 50 60 DC SML-210LT DF=50% PEAK FORWARD CURRENT : IF peak (mA) PEAK FORWARD CURRENT : IF peak (mA) Ratio of Maximum Tolerable Peak Current - Pulse Duration RATIO of MAXIMUM TOLERABLE PEAK CURRENT IF peak Max. IF Max. to MAXIMUM TOLERABLE DC CURRENT RATIO of MAXIMUM TOLERABLE PEAK CURRENT IF peak Max. IF Max. to MAXIMUM TOLERABLE DC CURRENT 6 5 4 200Hz 100Hz 10kHz 2kHz 1kHz 3 2.4 2 SML-210PT SML-210MT SML-210YT SML-210DT SML-210VT 6 5 4 200Hz 3 2.5 2 100Hz 10kHz 2kHz 1kHz SML-210LT 1 5 10 20 50 102 103 104 1 5 10 20 50 102 103 104 PULSE DURATION : Tw (μs) PULSE DURATION : Tw (μs) Derating MAXIMUM FORWARD CURRENT : IF Max. (mA) SML-210PT 30 SML-210MT SML-210YT SML-210DT 20 SML-210VT SML-210LT 10 0 0 10 20 30 40 50 60 70 80 90 AMBIENT TEMPERATURE : Ta (℃) Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1