SML-410

SURFACE MOUNT LED LAMPS Standard Type Mini-molded chip LEDs SML-410 Series Green Package Size （mm） GaP 570nm 1608 (0603) 1.6x0.8 t=0.4 SML-410MW ■ Absolute Maximum Ratings（Ta=25℃） Emitting dissipation color PD ■ External Dimensions（Unit：mm） 1.6 1.2 0.8 Part No. Peak Forward Reverse Operating Stotage forward current voltage temperature temperature current IF VR Topr Tstg ＊IFP （mW） （mA） （V） （°C） （°C） （mA） Power 65 25 60 4 -30 to +85 -40 to +85 SML-410MW Green LED ＊IFP measured under duty ≦1/ 5,pulse width ≦1ms. （0.14） ■ Electrical Optical Characteristics（Ta=25℃） Forward voltage VF Typ. (V) 2.2 IF (mA) 20 Terminal Part No. Resin Color Reverse current IR Max. (µA) 100 VR (V) 4 Peak Half-wave ∆λ λp Typ. (nm) 570 Typ. (nm) 40 IF (mA) 20 Min. ( mcd) Typ. IF (mcd) (mA) 16 20 Tolerance:±0.1 0.8 SML-410MW Milky White 3.6 ■ Directivity X’ Y’ 0° 30° 30° 0.65 Light wavelength Brightness IV 0.26 0.4 60° 0 50 90° 100 60° 90° 100 50 Relative brightness (%) (Typ.) ■ Recommemded Pad Layout ■ Packaging Spacifications（Unit：mm） Tape Spacifications：T86〈5,000pcs／reel〉 Reel Spacifications 0.8 Lavel Position Feeding direction 0.8 4 2 1.75 3.5 1.85 5.5 8 φ1.5 0.8 0.85 φ13 0.5 0.95 （Unit：mm） 0.5 φ60 φ180 The recommended thickness of the screen mask for soldering is between 100 and 200μm. The hole size of the screen mask should be same as the recommended land pattern or smaller. 11.4 SURFACE MOUNT LED LAMPS ■ Electrical Characteristic Curves Forward Current - Forward Voltage 50 FORWARD CURRENT : IF (mA) 20 10 5.0 2.0 1.0 0.5 0.2 0.1 1.5 2.0 2.5 3.0 Relative Luminous Intensity - Case Temperature SML-410MW 1.6 RELATIVE LUMINOUS INTENSITY IF=20mA 1.4 1.2 1.0 0.8 0.6 0.4 −20 0 20 40 SML-410MW Ta=25℃ 60 80 FORWARD VOLTAGE : VF (V) CASE TEMPERATURE : Tc (℃) Relative Luminous Intensity - Forward Current 3.0 RELATIVE LUMINOUS INTENSITY f=1kHz 2.5 DC Ratio of Maximum Tolerable Peak Current - Pulse Duration SML-410MW 10 SML-410MW IFP Max/IF Max 2.0 1.5 1.0 20% 0.5 0 0 15% 10% 5% 10 20 30 40 50 60 DF=50% 500Hz 200Hz 1000 50kHz 20kHz 10kHz 2.4 1 1 10 100 10000 PULSE DURATION : Tw (μs) PEAK FORWARD CURRENT : IF peak (mA) Derating MAXIMUM FORWARD CURRENT : (mA) 40 SML-410MW 30 20 10 0 0 10 20 30 40 50 60 70 80 90 100 AMBIENT TEMPERATURE : Ta (℃) 100Hz 5kHz 2kHz 1kHz Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1