TCA1E106M8R

Chip tantalum capacitors TC Series A Case Features (A) 1) Vital for all hybrid integrated circuits board application. 2) Wide capacitance range. 3) Screening by thermal shock. Dimensions (Unit : mm) Anode mark (Unit : mm) L H W1 Dimensions L W1 A case 3.2 + 0.2 − 1.6 + 0.2 − 1.2 + 0.2 − 1.6 + 0.2 − 0.8 + 0.3 − W2 W2 H S S S + − Part No. Explanation TC 1 A 2 0 3 J 1 0 4 6 M 5 8R 6 1 Series name TC 4 Nominal capacitance Nominal capacitance in pF in 3 digits: 2 significant figures followed by the figure representing the number of 0's. 5 Capacitance tolerance 2 Case style TC A 3 Rated voltage Rated voltage (V) CODE 4 6.3 10 16 20 25 35 0G 0J 1A 1C 1D 1E 1V M : + 20% − 6 Taping 8 : Reel width : 8mm R : Positive electrode on the side opposite to sprocket hole www.rohm.com c ○ 2011 ROHM Co., Ltd. All rights reserved. 1/7 2011.06 - Rev.F TC Series A Case  Rated table Rated voltage (V) (μF) 1 (105) 1.5 (155) 2.2 (225) 3.3 (335) 4.7 (475) 6.8 (685) 10 (106) 15 (156) 22 (226) 33 (336) 47 (476) 68 (686) 100 (107) 150 (157) Remark) Case size codes (A) in the above show products line-up. ∗ Under development Data Sheet 4 0G 6.3 0J 10 1A 16 1C A 20 1D A A A A A 25 1E A A A A A 35 1V ∗A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A    Marking  The indications listed below should be given on the surface of a capacitor. (1) Polarity : The polarity should be shown by bar. (on the anode side) (2) Rated DC voltage : Due to the small size of A case, a voltage code is used as shown below. (3) Visual typical example (1) voltage code (2) capacitance code Voltage Code g j A C D E V Rated DC Voltage (V) 4 6.3 10 16 20 25 35 Capacitance Code A E J N S W a e j n s w a Nominal Capacitance (μF) 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 [A case] note 1) j a −− (1) (2) ja note 2) voltage code and capacitance code are variable with parts number  www.rohm.com c ○ 2011 ROHM Co., Ltd. All rights reserved. 2/7 2011.06 - Rev.F TC Series A Case  Characteristics Item Operating Temperature Maximum operating temperature with no voltage derating Data Sheet Performance −55°C~+125°C +85°C 4 6.3 10 16 20 25 35 2.5 4 6.3 10 13 16 22 5 8 13 20 26 32 44 0.5μA or 0.01CV whichever is greater Shown in " Standard list " Test conditions (based on JIS C 5101−1 and JIS C 5101−3) Voltage reduction when temperature exceeds +85°C Rated voltage (VDC) Category voltage (VDC) Surge voltage (VDC) DC Leakage current at 85°C at 125°C at 85°C As per 4.9 JIS C 5101-1 As per 4.5.1 JIS C 5101-3 Voltage : Rated voltage for 1min As per 4.7 JIS C 5101-1 As per 4.5.2 JIS C 5101-3 Measuring frequency : 120±12Hz Measuring voltage : 0.5Vrms +1.5 to 2V.DC Measuring circuit : DC Equivalent series circuit As per 4.8 JIS C 5101-1 As per 4.5.3 JIS C 5101-3 Measuring frequency : 120±12Hz Measuring voltage : 0.5Vrms +1.5 to 2V.DC Measuring circuit : DC Equivalent series circuit As per 4.10 JIS C 5101-1 As per 4.5.4 JIS C 5101-3 Measuring frequency : 100±10kHz Measuring voltage : 0.5Vrms or less Measuring circuit : DC Equivalent series circuit Capacitance tolerance Shall be satisfied allowance range. ±20% Tangent of loss angle (Df, tan δ) Shall be satisfied the voltage on " Standard list " Impedance Shall be satisfied the voltage on " Standard list " Resistance to Soldering heat Appearance L.C. ΔC / C Df (tan δ) Temperature cycle As per 4.14 JIS C 5101-1 As per 4.6 JIS C 5101-3 Dip in the solder bath Less than initial limit Solder temp : 260±10°C : 5±0.5s TCA0G686M8R : Within ±15% of initial value Duration :1 TCA0G107M8R : Within ±20% of initial value Repetition After the specimens, leave it at room temperature for : Within ±5% of initial value Others over 24h and then measure the sample. Less than initial limit There should be no significant abnormality. The indications should be clear. There should be no significant abnormality. The indications should be clear. TCAP0J226 : Less than 150% of initial limit : Less than initial limit Others TCA0G686M8R : Within ±15% of initial value TCA0G107M8R : Within ±20% of initial value TCA0J476M8R : Within ±15% of initial value TCA1A226M8R : Within ±15% of initial value : Within ±10% of initial value Others Less than initial limit There should be no significant abnormality. The indications should be clear. As per 4.16 JIS C 5101-1 As per 4.10 JIS C 5101-3 Repetition : 5 cycles (1 cycle : steps 1 to 4) without discontinuation. Temp. 1 2 3 4 −55 + 3°C − Room temp. + 125 − 2°C Room temp. Time 30±3min. 3min.or less 30±3min. 3min.or less Appearance L.C. ΔC / C Df (tan δ) Moisture resistance After the specimens, leave it at room temperature for over 24h and then measure the sample. Appearance L.C. ΔC / C As per 4.22 JIS C 5101-1 As per 4.12 JIS C 5101-3 After leaving the sample under such atmospheric Less than initial limit condition that the temperature and humidity are TCA0G686M8R : Within ±15% of initial value 60±2°C and 90 to 95% RH,respectiveiy, for 500±12h TCA0G107M8R : Within ±20% of initial value leave it at room : Within ±10% of initial value temperature for over 24h and then measure the Others sample. TCA0G686M8R : Less than 150% of initial limit TCA0G107M8R : Less than 150% of initial limit Others : Less than initial limit Df (tan δ) www.rohm.com c ○ 2011 ROHM Co., Ltd. All rights reserved. 3/7 2011.06 - Rev.F TC Series A Case Item Temperature Stability Temp. Data Sheet Performance −55°C Within 0/−12% of initial value Shall be satisfied the voltage on " Standard list " − Test conditions (based on JIS C 5101−1 and JIS C 5101− 3) As per 4.29 JIS C 5101-1 As per 4.13 JIS C 5101-3 ΔC / C Df (tan δ) L.C. Temp. +85°C TCA0G686M8R : Within +12/0% of initial value TCA0G107M8R : Within +12/0% of initial value Others : Within +10/0% of initial value ΔC / C Df (tan δ) L.C. Temp. Shall be satisfied the voltage on " Standard list " Less than 1000% of initial limit +125°C Within +15/0% of initial value Shall be satisfied the voltage on " Standard list " Less than 1250% of initial limit ΔC / C Df (tan δ) L.C. Surge voltage Appearance L.C. ΔC / C Df (tan δ) Appearance Loading at High temperature L.C. As per 4.26JIS C 5101-1 As per 4.14JIS C 5101-3 Shall be satisfied the voltage on " Standard list " Apply the specified surge voltage via the serial resistance of 1kΩ every 5±0.5 min. TCA0G686M8R : Within ±15% of initial value for 30±5 s. each time in the atmospheric condition of 85±2°C. TCA0G107M8R : Within ±20% of initial value Repeat this procedure 1,000 times. Others : ±10% of initial value After the specimens, leave it at room temperature for over 24h and then measure the sample. Less than initial limit There should be no significant abnormality. There should be no significant abnormality. TCA0G686M8R : Less than 125% of initial limit TCA0G107M8R : Less than 125% of initial limit TCA1A226M8R : Less than 125% of initial limit TCA1E105M8R : Less than 125% of initial limit Others : Less than initial limit As per 4.23 JIS C 5101-1 As per 4.15 JIS C 5101-3 After applying the rated voltage for 2000+72/0 h without discontinuation via the serial resistance of 3Ω or less at a temperature of 85±2°C, leave the sample at room temperature / humidity for over 24h and measure the value. ΔC / C TCA0G686M8R : Within ±15% of initial value TCA0G107M8R : Within ±20% of initial value TCA0J476M8R : Within ±15% of initial value TCA1A226M8R : Within ±15% of initial value Others : Within±10% of initial value Less than initial limit The measured value should be stable. There should be no significant abnormality. Df (tan δ) Terminal strength Capacitance Appearance As per 4.35 JIS C 5101-1 As per 4.9 JIS C 5101-3 A force is applied to the terminal until it bends to 1mm and by a prescribed tool maintain the condition for 5s. (See the figure below) (Unit : mm) 50 20 F (Apply force) R230 1 thickness=1.6mm 45 45 www.rohm.com c ○ 2011 ROHM Co., Ltd. All rights reserved. 4/7 2011.06 - Rev.F TC Series A Case Item Adhesiveness Data Sheet Performance Test conditions (JIS C 5101−1 and JIS C 5101− 3) As per 4.34 JIS C 5101-1 As per 4.8 JIS C 5101-3 Apply force of 5N in the two directions shown in the figure below for 10±1s after mounting the terminal on a circuit board. product The terminal should not come off. ja Apply force a circuit board Dimensions Refer to "External dimensions" Measure using a caliper of JIS B 7507 Class 2 or higher grade. Resistance to solvents The indication should be clear As per 4.32 JIS C 5101-1 As per 4.18 JIS C 5101-3 Dip in the isopropyl alcohol for 30±5s, at room temperature. As per 4.15.2 JIS C 5101-1 As per 4.7 JIS C 5101-3 Dip speed=25±2.5mm / s Pre−treatment(accelerated aging): Leave the sample on the boiling distilled water for 1 h. Solder temp. : 245±5°C Duration : 3±0.5s Solder : M705 Flux : Rosin 25% IPA 75% As per 4.17 JIS C 5101-1 Frequency : 10 to 55 to 10Hz/min. Amplitude : 1.5mm Time : 2h each in X and Y directions Mounting : The terminal is soldered on a print circuit board. Solderability 3/4 or more surface area of the solder coated terminal dipped in the soldering bath should be covered with the new solder. Vibration Capacitance Measure value should not fluctuate during the measurement. Appearance There should be no significant abnormality. www.rohm.com c ○ 2011 ROHM Co., Ltd. All rights reserved. 5/7 2011.06 - Rev.F TC Series A Case  Standard products list, TC series A case Rated voltage 85°C (V) TC A 0G 475M8R TC A 0G 685M8R TC A 0G 106M8R TC A 0G 156M8R TC A 0G 226M8R TC A 0G 336M8R TC A 0G 476M8R TC A 0G 686M8R TC A 0G 107M8R TC A 0J 335M8R TC A 0J 475M8R TC A 0J 685M8R TC A 0J 106M8R TC A 0J 156M8R TC A 0J 226M8R TC A 0J 336M8R TC A 0J 476M8R TC A 1A 155M8R TC A 1A 225M8R TC A 1A 335M8R TC A 1A 475M8R TC A 1A 685M8R TC A 1A 106M8R TC A 1A 156M8R TC A 1A 226M8R TC A 1C 105M8R TC A 1C 155M8R TC A 1C 225M8R TC A 1C 335M8R TC A 1C 475M8R TC A 1C 685M8R TC A 1C 106M8R TC A 1D 105M8R TC A 1D 155M8R TC A 1D 225M8R TC A 1D 335M8R TC A 1D 475M8R TC A 1E 105M8R TC A 1E 155M8R TC A 1E 225M8R TC A 1E 335M8R TC A 1E 475M8R 4 4 4 4 4 4 4 4 4 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 10 10 10 10 10 10 10 10 16 16 16 16 16 16 16 20 20 20 20 20 25 25 25 25 25 35 Category voltage 125°C (V) 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 4 4 4 4 4 4 4 4 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 10 10 10 10 10 10 10 13 13 13 13 13 16 16 16 16 16 22 Surge voltage 85°C (V) 5 5 5 5 5 5 5 5 5 8 8 8 8 8 8 8 8 13 13 13 13 13 13 13 13 20 20 20 20 20 20 20 26 26 26 26 26 32 32 32 32 32 44 Cap. 120Hz (μF) 4.7 6.8 10 15 22 33 47 68 100 3.3 4.7 6.8 10 15 22 33 47 1.5 2.2 3.3 4.7 6.8 10 15 22 1 1.5 2.2 3.3 4.7 6.8 10 1 1.5 2.2 3.3 4.7 1 1.5 2.2 3.3 4.7 1 Df Impedance Leakage 120Hz 100kHz Tolerance current (%) 25°C 1WV.60s (%) 25°C 125°C −55°C (Ω) (μA) 85°C + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + − 20 + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − + 20 − 0.5 0.5 0.5 0.6 0.9 1.3 1.9 2.7 4 0.5 0.5 0.5 0.6 0.9 1.4 2.1 3.0 0.5 0.5 0.5 0.5 0.7 1.0 1.5 2.2 0.5 0.5 0.5 0.5 0.8 1.1 1.6 0.5 0.5 0.5 0.7 0.9 0.5 0.5 0.6 0.8 1.2 0.5 10 12 12 12 12 14 30 34 54 10 12 12 12 12 14 30 34 10 10 12 12 12 12 14 30 10 10 10 10 10 10 12 10 10 10 10 10 10 10 10 10 12 10 6 8 8 8 8 10 12 18 30 6 8 8 8 8 10 12 18 6 6 8 8 8 8 10 12 6 6 6 6 6 6 8 6 6 6 6 6 6 6 6 6 8 6 8 10 10 10 10 12 16 24 36 8 10 10 10 10 12 16 24 8 8 10 10 10 10 12 16 8 8 8 8 8 8 10 8 8 8 8 8 8 8 8 8 10 8 5.6 4.9 4.2 4 3 3.5 3.2 3 3 5.6 4.9 4.2 4 3 3.5 3.2 3.2 8.8 5.6 4.9 4.2 4 3 3.5 3.2 7 5.6 4.9 4.8 3.9 3.8 3.5 7 6 5.2 4.8 3.9 7 6 5.2 4.8 3.4 7 Data Sheet Part No. ∗ TC A 1V 105M8R ∗ =Under development www.rohm.com c ○ 2011 ROHM Co., Ltd. All rights reserved. 6/7 2011.06 - Rev.F TC Series A Case  Packaging specifications Case code A A+0.1 − 1.9 B+0.1 − 3.5 t1+ 0.05 − 0.25 t2 + 0.1 − 1.9 Data Sheet Taping [A case] 1.75±0.1 φ1.5 A B +0.1 −0 t1 3.5±0.05 8.0±0.2 Chip t2 4.0±0.1 4.0±0.1 2.0±0.05 Feeding direction  Packaging style Case code A case Packaging Taping Packaging style plastic taping φ180mm Reel Symbol Basic ordering units R 2,000pcs Reel [A case] +1.0 9.0 0 11.4+1.0 − φ13+0.2 − Pull direction Label sticking position EIAJ ET−7200B compatible www.rohm.com c ○ 2011 ROHM Co., Ltd. All rights reserved. 0 φ180−1.5 1 φ60 +0 7/7 2011.06 - Rev.F Notice Notes Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. R1120A