TCFGA0J475M8R

TCFG Series A Case Tantalum capacitors Chip tantalum capacitors (Fail-safe open structure type) TCFG Series A Case Features 1) Safety design by open function built - in. 2) Wide capacitance range 3) Screening by thermal shock. Dimensions (Unit : mm) Anode mark L W1 H W2 S + S − Case code A 3216-18(1206) L 3.2+0.2 − W1 1.6+0.2 − W2 1.2+0.2 − H 1.6+0.2 − S 0.8+0.3 − Part No. Explanation TCFGA 0J 1 06M 8R 1 2 3 4 5 6 1 Series name TCFG 4 Capacitance Nominal capacitance in pF in 3 digits : 2significant figure representing the number of 0's. 2 Case code TCFG ····· A 5 Capacitance tolerance 3 Rated voltage Rated voltage (V) CODE 4 6.3 10 16 20 25 0G 0J 1A 1C 1D 1E M : ± 20% K : ± 10% 6 Taping 8 : Tape width (8mm) R : Positive electrode on the side opposite to sprocket hole Rev.D 1/12 TCFG Series A Case Tantalum capacitors Capacitance range TCFG series A Case Rated voltage (V) (μF) 1.0 (105) 1.5 (155) 2.2 (225) 3.3 (335) 4.7 (475) 6.8 (685) 10 (106) 15 (156) 22 (226) 33 (336) 47 (476) 68 (686) : Indicates new product 4 G 6.3 J 10 A 16 C A 20 D A A A A A 25 E A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A Remark) Case size codes (A) in the above show each size products line-up. Marking The indications listed below should be given on the surface of a capacitor. Polarity : The polarity should be shown by bar. (on the anode side) Rated DC voltage : Due to the small size of A case, a voltage code is used as shown below. Visual typical example (1)voltage code (2) capacitance code [A Case] note 1) J 106 −− (1) (2) J106 note 2) voltage code and capacitance code are variable with parts number Rev.D 2/12 TCFG Series A Case Tantalum capacitors Characteristics Item Operating Temperature Performance −55 °C to +125 °C Test conditions (based on JIS C5101-1 and JIS C5101-3) Voltage reduction when temperature exceeds +85°C Maximum operating temperature +85 °C with no voltage derating Rated Voltage (V.DC) Category Voltage (V.DC) Surge Voltage DC leakage current 4 6.3 10 16 20 25 2.5 4 6.3 10 13 16 5.0 8 13 20 26 32 0.5μA or 0.01CV whichever is greater (Shown in "Standard list") Shall be satisfied allowance range. ±10%, ±20% at 85°C at 125°C at 85°C As per 4.9 JIS C 5101-1 As per 4.5.1 JIS C 5101-3 Voltage : Rated voltage for 1min As per 4.7 JIS C 5101-1 As per 4.5.2 JIS C 5101-3 Measuring frequency : 120±12Hz Measuring voltage : 0.5Vrms, +1.5V.DC Measuring circuit : DC Equivalent series circuit As per 4.8 JIS C 5101-1 As per 4.5.3 JIS C 5101-3 Measuring frequency : 120±12Hz Measuring voltage : 0.5Vrms, +1.5V.DC Measuring circuit : DC Equivalent series circuit As per 4.10 JIS C 5101-1 As per 4.5.4 JIS C 5101-3 Measuring frequency : 100±10kHz Measuring voltage : 0.5Vrms or less As per 4.14 JIS C 5101-1 As per 4.6 JIS C 5101-3 Dip in the solder bath Solder temp : 260±5°C Duration : 5±0.5s Repetition :1 After the specimens, leave it at room temperature for over 24h and then measure the sample. Dip in the solder bath Solder temp : 320±5°C As per 4.16 JIS C 5101-1 As per 4.10 JIS C 5101-3 Repetition : 5 cycles (1 cycle : steps 1 to 4) without discontinuation. Step 1 2 3 4 Temp. −55 + 3°C − Time 30 +3min − Capacitance tolerance Tangent of loss angle (Df, tanδ) Shall be satisfied the voltage on "Standard list" Impedance Shall be satisfied the voltage on "Standard list" Resistance to Appearance There should be no significant abnormality. The indications should be clear. soldering heat L.C ΔC / C tanδ Less than initial limit Within ±5% of initial value Less than initial limit Fail-Safe open unit actuation Within 320°C − 20s Temperature cycle Appearance There should be no significant abnormality. The indications should be clear. L.C ΔC / C Less than initial limit TCFGA1A226 TCFGA0J476 TCFGA0G686 Others : ±15% : ±15% : ±15% : ±10% tanδ Less than initial limit Room temp. 3min. or less 125 + 2°C 30 +3min − − Room temp. 3min. or less After the specimens, leave it at room temperature for over 24h and then measure the sample. Moisture resistance Appearance There should be no significant abnormality. The indications should be clear. L.C ΔC / C tanδ Less than initial limit Within ±10% of initial value Less than initial limit As per 4.12 JIS C 5101-1 As per 4.12 JIS C 5101-3 After leaving the sample under such atmospheric condition that the temperature and humidity are 60±2°C and 90 to 95%RH, respectively, for 500±12h level it at room temperature for over 24h and then measure the sample. Rev.D 3/12 TCFG Series A Case Tantalum capacitors Item Temperature Temp. Stability ΔC / C tanδ L.C Performance −55°C Within 0/−12%of initial value Shall be satisfied the voltage on "Standard list" − +85°C Within +10/0%of initial value Shall be satisfied the voltage on "Standard list" 5μA or 0.1CV whichever is greater +125°C Within +15/0%of initial value Shall be satisfied the voltage on "Standard list" 6.3μA or 0.125CV whichever is greater Test conditions (based on JIS C5101-1 and JIS C5101-3) As per 4.29 JIS C 5101-1 As per 4.13 JIS C 5101-3 Temp. ΔC / C tanδ L.C Temp. ΔC / C tanδ L.C Surge Voltage Appearance There should be no significant abnormality. The indications should be clear. L.C Less than initial limit Within ±10%of initial value ΔC / C As per 4.26 JIS C 5101-1 As per 4.14 JIS C 5101-3 Apply the specified surge voltage every 5±0.5min. for 30±5 s. each time in the atmospheric condition of 85±2°C. Repeat this procedure 1,000 times. After the specimens, leave it at room temperature for over 24h and then measure the sample. tanδ Less than initial limit As per 4.23 JIS C 5101-1 As per 4.15 JIS C 5101-3 After applying the rated voltage for 2000+72/0h without discontinuation via the serial resistance of 3Ω or less at a temperature of 85±2°C, leave the sample at room temperature/humidity for over 24h and measure the value. Loading at Appearance There should be no significant abnormality. High The indications should be clear. temperature L.C Less than initial limit ΔC / C TCFGA1A226 TCFGA0J476 TCFGA0G686 Others : ±15% : ±15% : ±15% : ±10% tanδ Terminal Strength Less than initial limit As per 4.35 JIS C 5101-1 As per 4.9 JIS C 5101-3 A force is applied to the terminal until it bends to 1mm and by a prescribed tool maintain the condition for 5s. (See the figure below.) (Unit : mm) 50 20 F (Apply force) Capacitance The measured value should be stable. Appearance There should be no significant abnormality. R230 1 Thickness 1.6mm 45 45 Adhesiveness The terminal should not come off. As per 4.34 JIS C 5101-1 As per 4.8 JIS C 5101-3 Apply force of 5N in the two directions shown in the figure below for 10±1s after mounting the terminal on a circuit board. product C105 Apply force YAA a circuit board Rev.D 4/12 TCFG Series A Case Tantalum capacitors Item Dimensions Performance Be based on "External dimensions" Test conditions (based on JIS C5101-1 and JIS C5101-3) Measure using a caliper of JIS B 7505 Class 2 or higher grade. As per 4.32 JIS C 5101-1 As per 4.18 JIS C 5101-3 Dip in the isopropyl alcohol for 30±5s, at room temperature. As per 4.15.2 JIS C 5101-1 As per 4.7 JIS C 5101-3 Dip speed = 25±2.5mm/s Pre-treatment (accelerated aging) : Leave the sample on the boiling distilled water for 1h. Solder temp. : 245±5°C Duration : 3±0.5s Solder : M705 Flux : Rosin 25%, IPA 75% As per 4.17 JIS C 5101-1 Frequency : 10 to 55 to 10Hz/min. Amplitude : 1.5mm Time : 2h each in X and Y directions Mounting : The terminal is soldered on a print circuit board. Resistance to solvents The indication should be clear. Solderability 3/4 or more surface area of the solder coated terminal dipped in the soldering bath should be covered with the new solder. Vibration Capacitance The measured value should be stable. Appearance There should be no significant abnormality. Rev.D 5/12 TCFG Series A Case Tantalum capacitors Standard list, TCFG series A Cases (A : 3216) Leakage Rated Derated Surge DF 120Hz Impedance current Voltage Voltage Voltage Capacitance (%) 100kHz Case Tolerance 25°C @85°C @125°C @85°C 120Hz code (%) 1WV.60s −55°C 25°C 125°C (μF) (V) (V) (Ω) (V) (μA) 85°C 4 4 4 4 4 4 4 4 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 10 10 10 10 10 10 10 10 16 16 16 16 16 16 16 20 20 20 20 20 25 25 25 25 25 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 4 4 4 4 4 4 4 4 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 10 10 10 10 10 10 10 13 13 13 13 13 16 16 16 16 16 5 5 5 5 5 5 5 5 8 8 8 8 8 8 8 8 13 13 13 13 13 13 13 13 20 20 20 20 20 20 20 26 26 26 26 26 32 32 32 32 32 4.7 6.8 10 15 22 33 47 68 3.3 4.7 6.8 10 15 22 33 47 1.5 2.2 3.3 4.7 6.8 10 15 22 1.0 1.5 2.2 3.3 4.7 6.8 10 1.0 1.5 2.2 3.3 4.7 1.0 1.5 2.2 3.3 4.7 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 ±20, ±10 Part No. TCFG A 0G 475 TCFG A 0G 685 TCFG A 0G 106 TCFG A 0G 156 TCFG A 0G 226 TCFG A 0G 336 TCFG A 0G 476 TCFG A 0G 686 TCFG A 0J 335 TCFG A 0J 475 TCFG A 0J 685 TCFG A 0J 106 TCFG A 0J 156 TCFG A 0J 226 TCFG A 0J 336 TCFG A 0J 476 TCFG A 1A 155 TCFG A 1A 225 TCFG A 1A 335 TCFG A 1A 475 TCFG A 1A 685 TCFG A 1A 106 TCFG A 1A 156 TCFG A 1A 226 TCFG A 1C 105 TCFG A 1C 155 TCFG A 1C 225 TCFG A 1C 335 TCFG A 1C 475 TCFG A 1C 685 TCFG A 1C 106 TCFG A 1D 105 TCFG A 1D 155 TCFG A 1D 255 TCFG A 1D 335 TCFG A 1D 475 TCFG A 1E 105 TCFG A 1E 155 TCFG A 1E 255 TCFG A 1E 335 TCFG A 1E 475 0.5 0.5 0.5 0.6 0.9 1.3 1.9 3.0 0.5 0.5 0.5 0.6 0.9 1.4 2.1 3.0 0.5 0.5 0.5 0.5 0.7 1.0 1.5 2.2 0.5 0.5 0.5 0.5 0.8 1.1 1.6 0.5 0.5 0.5 0.7 0.9 0.5 0.5 0.6 0.8 1.2 10 12 12 12 12 14 30 32 10 12 12 12 12 14 30 34 10 10 12 12 12 12 14 30 10 10 10 10 10 10 12 10 10 10 10 10 8 10 10 10 12 6 8 8 8 8 10 12 16 6 8 8 8 8 10 12 18 6 6 8 8 8 8 10 12 6 6 6 6 6 6 8 6 6 6 6 6 6 6 6 6 8 8 10 10 10 10 12 16 20 8 10 10 10 10 12 16 24 8 8 10 10 10 10 12 16 8 8 8 8 8 8 10 8 8 8 8 8 8 8 8 8 10 5.6 4.9 4.2 4.0 3.0 3.5 3.2 3.0 5.6 4.9 4.2 4.0 3.0 3.5 3.2 3.2 8.8 5.6 4.9 4.2 4.0 3.0 3.5 3.2 7 5.6 4.9 4.8 3.9 3.8 3.5 7 6.0 5.2 4.8 3.9 7 6.0 5.2 4.8 3.4 A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A =Tolerance (M : ±20%, K : ±10%) Rev.D 6/12 TCFG Series A Case Tantalum capacitors Packaging specifications Case code A (3216) A±0.1 1.9 B±0.1 3.5 t1±0.05 0.25 t2±0.1 1.9 Taping A case 1.75 + 0.1 − φ1.5 +0.1 −0 A B t1 4.0 + 0.1 − 2.0 + 0.05 − 4.0 + 0.1 − 3.5 + 0.05 − 8.0 + 0.2 − Component is loaded t2 Pull-out direction Packaging style Case code A Case Packaging Taping Packaging style Plastic taping φ180mm reel Symbol R Basic ordering unit 2,000 Reel Plastic reel 9.0 +1.0 0 11.4±1.0 φ13±0.2 Label sticking position EIAJ ET - 7200B 0 φ 180 −1.5 φ 60 +1 0 Rev.D 7/12 TCFG Series A Case Tantalum capacitors Recommended condition of reflow soldering (1) Leakage current-to-voltage ratio LEALKAGE CURRENT RATIO DCL / DCL 1 0.1 0.01 0 20 40 60 80 100 % OF RATED VOLTAGE (VR) Fig.1 (2) Derating voltage as function of temperature 100 85°C Rated Voltage (V.DC) Surge Voltage (V.DC) 5.0 8 13 20 26 32 125°C Category Voltage (V.DC) 2.5 4 6.3 10 13 16 Surge Voltage (V.DC) 3.2 5 8 13 16 20 PERCENT OF 85°C RVDC1 (VR) 90 80 4 6.3 70 10 16 20 25 60 50 75 85 95 105 115 125 TEMPERATURE ( C) Fig.2 (3) Reliability The malfunction rate of tantalum solid state electrolytic capacitors varies considerably depending on the conditions of usage (ambient temperature, applied voltage, circuit resistance). Formula for calculating malfunction rate p= b ( p b E SR Q CV E SR Q CV) : Malfunction rate stemming from operation : Basic malfunction rate : Environmental factors : Series resistance : Level of malfunction rate : Capacitance For details on how to calculate the malfunction rate stemming from operation, see the tantalum solid state electrolytic capacitors column in MIL-HDBK-217. Rev.D 8/12 TCFG Series A Case Tantalum capacitors Malfunction rate as function of operating temperature and rated voltage 1.0 Ratio = FAILURE RATE COEFFICIENT Malfunction rate as function of circuit resistance ( /V) 6.0 RESISTANCE COEFFICIENT (π) Applied Voltage Rated Voltage 0.5 0.3 0.2 0.1 0.06 0.03 0.02 0.01 20 40 60 1.0 4.0 0.7 2.0 0.5 1.0 0.8 0.6 0.4 0.1 0.2 0.4 0.6 1.0 2.0 3.0 0.3 0.1 85 OPERATING TEMPERATURE ( C) RESISTANCE OF CIRCUIT (Ω / V) Fig.3 Fig.4 (4) External temperature vs. fuse blowout (5) Power vs. fuse blowout characteristics / Product surface temperature 100 90 OPERATING TIME (sec) 80 70 60 50 40 30 20 10 operating area 150 P case (2012) A case (3216) B case (3528) open-function charcteristic surface temp. 250 curve of the products 200 EXTERNAL TEMPERATURE (°C) 350 340 330 320 310 300 290 280 270 260 1 10 no failed P case (2012) A case (3216) B case (3528) 300 failed half failed 100 OPERATING TIME (sec) 0 012345678 no operating area ELECTRIC POWER (W) 9 10 Fig.5 Fig.6 Note: Solder the chip at 300 C or less. If it is soldered using a temperature higher than 300 C, open function built-in may operate. Rev.D SURFACE TEMP. OF THE PRODUCT (°C) 360 9/12 TCFG Series A Case Tantalum capacitors (6) Maximum power dissipation Warming of the capacitor due to ripple voltage balances with warming caused by Joule heating and by radiated heat. Maximum allowable warming of the capacitor is to 5 C above ambient temperature. When warming exceeds 5 C, it can damage the dielectric and cause a short circuit. Power dissipation (P) = I2 R Ripple current P : As shown in table at right R : Equivalent series resistance Notes: 1. Please be aware that when case size is changed, maximum allowable power dissipation is reduced. 2. Maximum power dissipation varies depending on the package. Be sure to use a case which will keep warming within the limits shown in the table below. Allowable power dissipation (W) and maximum temperature rising Case Ambient temp. +25°C 0.070 5 +55°C 0.063 5 +85°C 0.056 5 +125°C 0.028 2 A case (3216) Max. Temp Rise[°C] (7) Impedance frequency characteristics 100000 10000 IMPEDANCE (Ω) (8) ESR frequency characteristics 100 A105 P case (2012) G475 A case (3216) C105 A case (3216) C335 B case (3528) 1000 100 10 1 ESR (Ω) A105 P case (2012) G475 A case (3216) C105 A case (3216) C335 B case (3528) 10 1 0.1 1 100 10k 1M 100M 500M 1 100 10k 1M 100M 500M FREQUENCY (Hz) FREQUENCY (Hz) Fig.7 Fig.8 (9) Temperature characteristics 10 CAP 120Hz 10V−1μF P case (2012) 4V−4.7μF A case (3216) 4V−33μF B case (3528) 5 6 CAP CHANGE (%) 4 DF 120Hz 10V−1μF P case (2012) 4V−4.7μF A case (3216) 4V−33μF B case (3528) 2 0 −2 3 DF (%) 2 −6 1 −10 −55 25 85 125 0 −55 25 85 125 TEMPERATURE (°C) TEMPERATURE (°C) Fig.9 Fig.10 Rev.D 10/12 TCFG Series A Case Tantalum capacitors 1000 LC 1WV 10V−1μF P case (2012) 4V−4.7μF A case (3216) 4V−33μF B case (3528) IMPEDANCE (Ω) 3 IMPEDANCE 100kHz 10V−1μF P case (2012) 4V−4.7μF A case (3216) 4V−33μF B case (3528) 100 LC (nA) 2 10 1 0 −55 25 85 125 0 −55 25 85 125 TEMPERATURE (°C) TEMPERATURE (°C) Fig.11 Fig.12 Inrush current Beware of inrush current. Inrush currents are inversely proportional ESR. Large inrush currents can cause components failure. 100 33μF 33μF tantalum capacitor aluminum electrolysis 100μF 4.7μF 4.7μF 47μF 22μF 1 Vpp=10V llimit=20A Pulse Width=500μs Power OP Amp Slew Rate=10V/6μs 0.1 0.1 1 ESRΩ (100kHz) 10 100 INRUSH CURRENT (A) 10 15μF Fig. 13 Maximum inrush current and ESR Inrush current can be limited by means of a protective resistor. 100 SAMPLE 16V−3.3μF Pulse width=500μs Slew rate=10V−6μc Current limit=20A R=0Ω V I = 0.476 R 10 0.25 0.5 1.0 2.0 5.0 I (A) 1 V I = 0.476+R 0.1 0.1 1 V (V) 10 100 Fig. 14 Imax change due to protective resistor R Rev.D 11/12 TCFG Series A Case Tantalum capacitors (10) Ultrasonic cleaning Carry out cleaning under as mild conditions as possible. The internal element of a tantalum capacitor are larger than those of a transistor or diode, so it is not as resistant as ultrasonic waves. Example : water Propagation speed Solvent density Frequency and wavelength Frequency Wavelength 20kHz 7.5cm 28kHz 5.3cm 50kHz 3.0cm 1500m / s 3 1g / cm Precautions 1) Do not allow solvent to come to a boil (kinetic energy increases). Ultrasonic output 0.5W / cm2 or less Use a solvent with a high boiling point. Lower solvent temperature. 2) Ultrasonic cleaning frequency 28 kHz or less 3) Keep cleaning time as short as possible. 4) Move item being cleaned. Standing waves caused by the ultrasonic waves can cause stress to build up in part of the item being cleaned. Reference Kin etic energy = 2 × π × frequency × 2 × Ultrasonic output propagation × speed × solvent density Rev.D 12/12 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of which would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM cannot be held responsible for any damages arising from the use of the products under conditions out of the range of the specifications or due to non-compliance with the NOTES specified in this catalog. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact your nearest sales office. ROHM Customer Support System www.rohm.com Copyright © 2007 ROHM CO.,LTD. THE AMERICAS / EUPOPE / ASIA / JAPAN Contact us : webmaster@ rohm.co. jp 21, Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan TEL : +81-75-311-2121 FAX : +81-75-315-0172 Appendix1-Rev2.0