TCFGD1C227MCR

Chip tantalum capacitors with (Fail-safe open structure type) TCFG series D Case Features 1) Safety design by open function built - in. 2) Wide capacitance range 3) Screening by thermal shock. Dimensions (Unit : mm) Anode mark L W1 H W2 S + S − Case code D 7343-30(2917) L 7.3+0.2 − W1 4.3 +0.2 − W2 2.4+0.1 − H 2.8+0.2 − S 1.3+0.2 − Part No. Explanation TCFGD 0J 227MCR 1 2 3 4 5 6 1 Series name TCFG 4 Capacitance Nominal capacitance in pF 3 digits : 2 significant figure representing the number of 0's. 2 Case code TCFG ······ D 5 Capacitance tolerance 3 Rated Voltage Rated voltage (V) CODE 4 6.3 10 16 20 25 0G 0J 1A 1C 1D 1E M : + 20% − 6 Taping C : Reel width (12mm) R : Positive electrode on the side opposite to sprocket hole www.rohm.com c ○ 2010 ROHM Co., Ltd. All rights reserved. 1/6 2010.01 - Rev.G TCFG Series D Case Capacitance range TCFG series D Case Rated voltage (V) (μF) 47 (476) 68 (686) 100 (107) 150 (157) 220 (127) 330 (337) D∗ D D D D∗ 4 0G 6.3 0J 10 1A 16 1C 20 1D 25 1E D Data Sheet Remark) Case size codes (D) in the above shown each size products line-up. ∗ : Under development Marking The indication listed below should be given on the surface of a capacitor. Polarity Rated DC voltage Nominal capacitance : The polarity should be shown by bar. (on the anode side) [D Case] note 1) Visual typical example (1) capacitance code (2) voltage code (1) 220μF (2) 6.3V 220 220 6.3V note 2) voltage code and capacitance code are variable with parts number www.rohm.com c ○ 2010 ROHM Co., Ltd. All rights reserved. 2/6 2010.01 - Rev.G TCFG Series D Case Characteristics Item Operating Temperature Performance −55 °C to +125 °C Test conditions (based on JIS C5101-1 and JIS C5101-3) Voltage reduction when temperature exceeds +85°C Data Sheet Maximum operating temperature +85 °C with no voltage derating Rated Voltage (V.DC) Category Voltage (V.DC) Surge Voltage DC leakage current 4 6.3 10 16 20 25 2.5 4 6.3 10 13 16 5.0 8 13 20 26 32 0.5μA or 0.01CV whichever is greater (Shown in "Standard list") Shall be satisfied allowance range. ±20% at 85°C at 125°C at 85°C As per 4.9 JIS C 5101-1 As per 4.5.1 JIS C 5101-3 Voltage : Rated voltage for 1 min As per 4.7 JIS C 5101-1 As per 4.5.2 JIS C 5101-3 Measuring frequency : 120±12Hz Measuring voltage : 0.5Vrms, +1.5 to 2V.DC Measuring circuit : DC Equivalent series circuit As per 4.8 JIS C 5101-1 As per 4.5.3 JIS C 5101-3 Measuring frequency : 120±12Hz Measuring voltage : 0.5Vrms, +1.5 to 2V.DC Measuring circuit : DC Equivalent series circuit As per 4.10 JIS C 5101-1 As per 4.5.4 JIS C 5101-3 Measuring frequency : 100±10kHz Measuring voltage : 0.5Vrms or less Measuring circuit : DC Equivalent series circuit Capacitance tolerance Tangent of loss angle (Df, tanδ) Shall be satisfied the voltage on "Standard list" Impedance Shall be satisfied the voltage on "Standard list" Resistance to Appearance There should be no significant abnormality. The indications should be clear. soldering heat L.C ΔC / C tanδ As per 4.14 JIS C 5101-1 As per 4.6 JIS C 5101-3 TCFGD1E476 : Less than 150% of initial limit Dip in the solder bath Solder temp : 260±10°C : Less than initial limit Others Duration : 5±0.5s Within ±12% of initial value Repetition :1 After the specimens, leave it at room temperature for Less than 150% of initial limit over 24h and then measure the sample. Dip in the solder bath Solder temp : 330±5°C Fail-Safe open unit actuation Within 330°C − 20s Temperature cycle Appearance There should be no significant abnormality. L.C ΔC / C tanδ As per 4.16 JIS C 5101-1 As per 4.10 JIS C 5101-3 Repetition : 5 cycles (1 cycle : steps 1 to 4) TCFGD1E476 : Less than 150% of initial limit without discontinuation. : Less than initial limit Others Step Temp. Time Within ±20% of initial value −55 + 3°C 1 30 +3min − − Less than 150% of initial limit 2 Room temp. 3min. or less + 3 125 − 2°C 30 +3min − 4 Room temp. 3min. or less After the specimens, leave it at room temperature for over 24h and then measure the sample. Moisture resistance Appearance There should be no significant abnormality. The indications should be clear. L.C ΔC / C tanδ As per 4.22 JIS C 5101-1 As per 4.12 JIS C 5101-3 TCFGD1E476 : Less than 150% of initial limit After leaving the sample under such atmospheric condition that the temperature and humidity are : Less than initial limit Others 60±2°C and 90 to 95%RH, respectively, for Within ±20% of initial value 500±12h level it at room temperature for over 24h and then measure the sample. Less than 150% of initial limit www.rohm.com c ○ 2010 ROHM Co., Ltd. All rights reserved. 3/6 2010.01 - Rev.G TCFG Series D Case Item Temperature Temp. Stability ΔC / C tanδ L.C Data Sheet Performance Test conditions (based on JIS C5101-1 and JIS C5101-3) As per 4.29 JIS C 5101-1 As per 4.13 JIS C 5101-3 −55°C Within 0/−20%of initial value Shall be satisfied the voltage on "Standard list" − +85°C Within +12/0%of initial value Shall be satisfied the voltage on "Standard list" Less than 1000% of initial limit +125°C Within +20/0%of initial value Shall be satisfied the voltage on "Standard list" Less than 1250% of initial limit Temp. ΔC / C tanδ L.C Temp. ΔC / C tanδ L.C Surge Voltage Appearance There should be no significant abnormality. L.C TCFGD1E476 Others : Less than 150% of initial limit : Less than initial limit ΔC / C tanδ Within ±10%of initial value Less than 150% of initial limit As per 4.26 JIS C 5101-1 As per 4.14 JIS C 5101-3 Apply the specified surge voltage via the serial resistance of 1kΩ every 5±0.5min.for 30±5 s. each time in the atmospheric condition of 85±2°C. Repeat this procedure 1,000 times. After the specimens, leave it at room temperature for over 24h and then measure the sample. As per 4.23 JIS C 5101-1 As per 4.15 JIS C 5101-3 After applying the rated voltage for 2000+72/0h without discontinuation via the serial resistance of 3Ω or less at a temperature of 85±2°C, leave the sample at room temperature/humidity for over 24h and measure the value. As per 4.35 JIS C 5101-1 As per 4.9 JIS C 5101-3 A force is applied to the terminal until it bends to 1mm and by a prescribed tool maintain the condition for 5s. (See the figure below.) (Unit : mm) 50 20 F (Apply force) Loading at Appearance There should be no significant abnormality. High TCFGD1E476 : Less than 150% of initial limit temperature L.C : Less than 125% of initial limit Others ΔC / C tanδ Terminal Strength Within ±10%of initial value Less than 150% of initial limit Capacitance The measured value should be stable. Appearance There should be no significant abnormality. R230 1 Thickness 1.6mm 45 45 Adhesiveness The terminal should not come off. As per 4.34 JIS C 5101-1 As per 4.8 JIS C 5101-3 Apply force of 5N in the two directions shown in the figure below for 10±1s after mounting the terminal on a circuit board. product C105 Apply force YAA a circuit board www.rohm.com c ○ 2010 ROHM Co., Ltd. All rights reserved. 4/6 2010.01 - Rev.G TCFG Series D Case Item Dimensions Performance Be based on "External dimensions" Test conditions (based on JIS C5101-1 and JIS C5101-3) Measure using a caliper of JIS B 7505 Class 2 or higher grade. As per 4.32 JIS C 5101-1 As per 4.18 JIS C 5101-3 Dip in the isopropyl alcohol for 30±5s, at room temperature. As per 4.15.2 JIS C 5101-1 As per 4.7 JIS C 5101-3 Dip speed = 25±2.5mm/s Pre-treatment (accelerated aging) : Leave the sample on the boiling distilled water for 1h. Solder temp. : 245±5°C Duration : 3±0.5s Solder : M705 Flux : Rosin 25%, IPA 75% As per 4.17 JIS C 5101-1 Frequency : 10 to 55 to 10Hz/min. Amplitude : 1.5mm Time : 2h each in X and Y directions Mounting : The terminal is soldered on a print circuit board. Data Sheet Resistance to solvents The indication should be clear. Solderability 3/4 or more surface area of the solder coated terminal dipped in the soldering bath should be covered with the new solder. Vibration Capacitance Measure value should not fluctuate during the measurement. Appearance There should be no significant abnormality. Table 1 standard list, TCFG series D Case (D : 7343) Leakage Rated Derated Surge Impedance DF120Hz Capacitance (%) 100kHz Case Tolerance current Voltage Voltage Voltage 120Hz 25C @85°C @125°C @85°C (%) code 1WV.60s −55°C 25°C 125°C (F) (Ω) (V) (V) (V) (mA) 85˚C 6.3 10 16 25 4 6.3 10 16 8 13 20 32 220 150 100 47 ±20 ±20 ±20 ±20 Part No. TCFG D 0J 227 M8R TCFG D 1A 157 M8R TCFG D 1C 107 M8R TCFG D 1E 476 M8R 13.8 15.0 16 11.8 30 14 14 14 12 10 10 10 16 12 12 12 0.70 0.70 0.70 0.70 D D D D www.rohm.com c ○ 2010 ROHM Co., Ltd. All rights reserved. 5/6 2010.01 - Rev.G TCFG Series D Case Packaging specifications Taping Case code D (7343) A±0.2 4.8 B±0.2 7.7 t1±0.1 0.3 t2±0.2 3.3 Data Sheet Taping D case 1.75±0.1 φ1.5 A B +0.1 0 t1 5.5±0.1 12.0±0.3 Products 8.0±0.1 2.0±0.1 Pull out direction 4.0±0.1 t2 Packaging style Case size D Case Packaging Taping Packaging style Plastic taping φ180mm reel Symbol R Basic ordering unit 500 Reel Plastic reel 13.0 +1.0 0 15.4±1.0 φ13±0.2 Label sticking position EIAJ ET - 7200B compatible www.rohm.com c ○ 2010 ROHM Co., Ltd. All rights reserved. 0 φ180 −1.5 φ60 +1 0 6/6 2010.01 - Rev.G Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2010 ROHM Co., Ltd. All rights reserved. R1010A