TCOB1A476M8R

Conductive polymer chip capacitors (Standard) TCO Series B Case Data sheet Features 1) Conductive polymer used at the cathode for ultra-low ESR. 2) Conductive polymer has a self-healing function that prevents failure, resulting in safe, high reliability operation. 3) Screening by thermal shock. Dimensions Anode mark (Unit : mm) L Dimensions Size L 3.5 ± 0.2 W1 2.8 ± 0.2 W2 1.9 ± 0.2 H 1.9 ± 0.2 S 0.8 ± 0.3 W1 H W2 S S − + Part No. Explanation T C O B 1 2 1 0 J 4 3 TCO 2 Case style 5 8 R 5 6 E 7 Nominal capacitance Capacitance tolerance M : ± 20% Rated voltage Rated voltage (V) 2.5 4 6.3 10 16 20 25 CODE M Nominal capacitance in pF in 3 digits: 2 significant figures followed by the figure representing the number of 0's. B : 3528-21 (1411) size 3 6 4 4 Series name 7 6 Taping 8 : Tape width R : Positive electrode on the side opposite to sprocket hole 0E 0G 0J 1A 1C 1D 1E 7 Discrimination code ∗This specification has possibility of charge, due to underdevelopment product. Please ask for latest specification to our sales. www.rohm.com c 2015 ROHM Co., Ltd. All rights reserved. ○ 1/6 2015.06 - Rev.M Data sheet TCO Series B Case Rated table (ESR : mΩ) Rated voltage (V.DC) Capacitance (μF) 4 2.5 6.3 10 16 15 (156) 25 100 150 33 (336) 47 (476) 70/150 100 (107) 35/45/150 150 (157) 35/45/150 330 (337) 35/45 150 25 35/45/150 25 35/70/150 150 220 (227) 100 Under development Marking The indications listed below should be given on the surface of a capacitor. (1) Polarity : The polarity should be shown by bar. (on the anode side) (2) Rated DC voltage : A voltage code is shown as below table. (3) Capacitance : A capacitance code is shown as below table. Voltage Code Rated DC Voltage (V) Capacitance Code Nominal Capacitance ( F) e 2.5 e 15 g 4 n 33 s _ a _ e _ j _ n j 6.3 A 10 C 16 D 20 E 25 47 100 150 220 330 Visual typical example voltage code and capacitance code are variable with parts number. manufacture code [B case] EX.) j − (1) s − (2) (1) voltage code (2) capacitance code www.rohm.com c 2015 ROHM Co., Ltd. All rights reserved. ○ js 2/6 2015.06 - Rev.M Data sheet TCO Series B Case Characteristics Item Test conditions (based on JIS C 5101−1 and JIS C 5101−3) Performance Operating Temperature −55°C to +105°C Maximum operating temperature with no voltage derating +85°C Rated voltage (V.DC) Category voltage (V.DC) Surge voltage (V.DC) 2.5 4 2 3.2 3.2 5 Voltage reduction when temperature exceeds+85°C 20 25 at 85°C 5 8 12.8 16 22 at 105°C 8 13 32 at 85°C 6.3 10 16 20 26 3μA or 0.1CV whichever is greater Shown in " Standard list " Rated voltage for 5min ±20% Shall be satisfied allowance range. Measuring frequency : 120±12Hz Measuring voltage : 0.5Vrms +1.5 to 2V.DC Measuring circuit : DC Equivalent series circuit Tangent of loss angle (Df, tan δ) Shall be satisfied the voltage on " Standard list " Measuring frequency : 120±12Hz Measuring voltage : 0.5Vrms +1.5 to 2V.DC Measuring circuit : DC Equivalent series circuit ESR Shall be satisfied the voltage on " Standard list " Measuring frequency : 100±10kHz Measuring voltage : 0.5Vrms or less DC Leakage current Capacitance tolerance Resistance to Soldering heat Appearance There should be no significant abnormality. The indications should be clear. L.C. C/C tan δ Temperature cycle Within±20% of initial value Less than 150% of initial limit Appearance There should be no significant abnormality. L.C C/C Df (tan δ) Moisture resistance Less than 150% of initial limit (TCOB1E156M8R : Less than 300% of initial limit) C/C Df (tan δ) Repetition : 5 cycles (1 cycle : steps 1 to 4) without discontinuation. Less than 500% of initial limit Within 20% of intial value Less than 150% of initial limit Temp. Time 1 −55±3°C 30±3min 2 Room temp. 3min.or less 3 105±2°C 30±3min 4 Room temp. 3min.or less After the specimens, leave it at room temperature for over 24h and then measure the sample. Appearance There should be no significant abnormality. The indications should be L.C Dip in the solder bath Solder temp : 240±5°C Duration : 10±0.5s Repetition :1 After the specimens, leave it at room temperature for over 24h and then measure the sample. Less than 150% of initial limit (TCOB1E156M8R : Less than 500% of initial limit) +30% / −20% After leaving the sample under such atmospheric condition that the temperature and humidity are 40±2°C and 90 to 95% RH,respectiveiy,for 500±12h leave it at room temperature for over 24h and then measure the sample. Less than 150% of initial limit www.rohm.com c 2015 ROHM Co., Ltd. All rights reserved. ○ 3/6 2015.06 - Rev.M Data sheet TCO Series B Case Item Temperature Stebility Temp. C/C Df (tan δ) −55°C Within 0/−20% of initial value Shall be satisfied the voltage on " Standard list " − L.C Temp. C/C Surge voltage Within +50/0% of initial value Shall be satisfied the voltage on " Standard list " L.C Less than 1CV Appearance There should be no significant abnormality. L.C Less than initial limit (TCOB1E156M8R : Less than 300% of initial limit) Within±20% of initial value Df (tan δ) Less than initial limit Appearance There should be nonsignificant abnormality. L.C Less than 200% of initial limit C/C Terminal strength +105°C Df (tan δ) C/C Loading at High temperature Test conditions (based on JIS C 5101−1 and JIS C 5101−3) Performance Apply the specified serge voltage every 5±0.5 min. for 30±5 s. each time in the atmospheric condition of 85±2°C. Repeat this rocedure 1,000 times. After the specimens, leave it at room temperature for over 24h and then measure the sample. After applying the rated voltage for 1000+72 h without discontinuation via the serial resistance of 3Ω or less at a temperature of 85±2°C, leave the sample at room temperature / humidity for over 24h and measure the value. Within±20% of initial value Df (tan δ) 150% of initial limit less than Capacitance The measured value should be stable. Appearance There should nonsignificant abnormality. A force is applied to the terminal until it bends to 1mm and by a perscribed tool maintain the condition for5s.(See the figure below) 50 20 (Unit : mm) F (Apply force) R230 1mm thickness=1.6mm 45 The terminal should not come off. Adhesiveness 45 Apply force of 5N in the two directions shown in the figure below for 10±1s after mounting the terminal on a circuit board. product Apply force a circuit board Dimensions Refer to "External dimensions" Measure using a caliper of JISB 7507 Class 2 or higher grade. Resistance to solvents The indication should be clear Dip in the isopropyl alcohol for 30±5s, at room temperature. Solderability 3/4 or more surface area of the solder coated terminal dipped in the soldering bath should be covered with the new solder. Dip speed=25±2.5mm / s Pre−treatment(accelerated aging): Leave the sample on the boiling distilled water for 1 h. Solder temp. : 245±5°C Duration : 3±0.5s Solder : M705 Flux : Rosin25% IPA75% Capacitance Measure value should not fluctuate during the measurement. Appearance There should no significant abnormality. Frequency : 10 to 55 to 10Hz/min. Amplitude : 1.5mm Time : 2h each in X and Y directions Mounting : The terminal is soldered on a print circuit board. Vibration www.rohm.com c 2015 ROHM Co., Ltd. All rights reserved. ○ 4/6 2015.06 - Rev.M Data sheet TCO Series B Case Standard products list Df ESR Leakage 120Hz 100kHz current (%) 25°C 1WV.5min −55°C 25°C 105°C (mΩ) (μA) Rated voltage 85°C Category voltage 105°C Surge voltage 85°C Cap. 120Hz Tolerance (V) (V) (V) (μF) (%) TCO B 0E 227 M8R-EN 2.5 2 3.2 220 ± 20 55 8 8 12 35 TCO B 0E 227 M8R-ES 2.5 2 3.2 220 ± 20 55 8 8 12 45 TCO B 0E 227 M8R 2.5 2 3.2 220 ± 20 55 8 8 12 150 TCO B 0E 337 M8R-EN 2.5 2 3.2 330 ± 20 82.5 30 15 20 35 TCO B 0E 337 M8R-ES 2.5 2 3.2 330 ± 20 82.5 30 15 20 45 4 3.2 5 150 ± 20 60 8 8 12 150 6.3 5 8 47 ± 20 30 8 8 12 70 TCO B 0J 476 M8R 6.3 5 8 47 ± 20 30 8 8 12 150 TCO B 0J 107 M8R-EN 6.3 5 8 100 ± 20 63 8 8 12 35 TCO B 0J 107 M8R-ES 6.3 5 8 100 ± 20 63 8 8 12 45 TCO B 0J 107 M8R 6.3 5 8 100 ± 20 63 8 8 12 150 ∗ TCO B 0J 157 M8R-EK 6.3 5 8 150 ± 20 94.5 30 15 20 25 TCO B 0J 157 M8R-EN 6.3 5 8 150 ± 20 94.5 30 15 20 35 TCO B 0J 157 M8R-ES 6.3 5 8 150 ± 20 94.5 30 15 20 45 TCO B 0J 157 M8R 6.3 5 8 150 ± 20 94.5 30 15 20 150 ∗ TCO B 0J 227 M8R-EK 6.3 5 8 220 ± 20 139 30 15 20 25 TCO B 0J 227 M8R-EN 6.3 5 8 220 ± 20 139 30 15 20 35 TCO B 0J 227 M8R-ES 6.3 5 8 220 ± 20 139 30 15 20 45 TCO B 0J 227 M8R 6.3 5 8 220 ± 20 139 30 15 20 150 TCO B 1A 336 M8R 10 8 13 33 ± 20 33 8 8 12 150 TCO B 1A 476 M8R 10 8 13 47 ± 20 47 8 8 12 150 ∗ TCO B 1C 336 M8R 16 12.8 20 33 ± 20 158 10 10 15 100 ∗ TCO B 1E 156 M8R 25 20 29 15 ± 20 113 10 10 20 100 Part No. TCO B 0G 157 M8R ∗TCO B 0J 476 M8R-EW ∗ = Under development Please consult a ROHM representative for additional details. www.rohm.com c 2015 ROHM Co., Ltd. All rights reserved. ○ 5/6 2015.06 - Rev.M Data sheet TCO Series B Case Packaging specifications Sprocket hole φD0 t1 E A F W B t2 P2 P1 P0 Pull-out direction Component is loaded (Unit : mm) A B W E F P1 P2 P0 3.3±0.1 3.8±0.1 8.0±0.2 1.75±0.1 3.5±0.05 4.0±0.1 2.0±0.05 4.0±0.1 t1 φ1.5±0.1/0 0.25±0.05 standard packaging quantity 2.2±0.1 2000pcs One reel is packed in aluminum bag. The size of aluminum bag is 240(a) x 250(b)mm. The size up to 230(c)mm is to zipper. A desiccant is packed with a reel. The aluminum bag is heat-sealed. The label of the same as the label on the reel is placed on the aluminum bag. 0 φ180 −1.5 +1.0 φ60 0 φ13±0.2 11.4±1.0 b c Label t2 Damp proof package +1.0 9.0 0 Reel dimensions D0 Pull-out direction a (Unit : mm) EIAJ ET−7200A www.rohm.com c 2015 ROHM Co., Ltd. All rights reserved. ○ 6/6 2015.06 - Rev.M Datasheet Notice Precaution on using ROHM Products 1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you (Note 1) , transport intend to use our Products in devices requiring extremely high reliability (such as medical equipment equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅢ CLASSⅣ CLASSⅢ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice-PGA-E © 2015 ROHM Co., Ltd. All rights reserved. Rev.001 Datasheet Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign trade act, please consult with ROHM in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the Products with other articles such as components, circuits, systems or external equipment (including software). 3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the Products, subject to the terms and conditions herein. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice-PGA-E © 2015 ROHM Co., Ltd. All rights reserved. Rev.001 Datasheet General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s representative. 3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. Notice – WE © 2015 ROHM Co., Ltd. All rights reserved. Rev.001 Datasheet TCOB1A476M8R - Web Page Buy Distribution Inventory Part Number Package Unit Quantity Minimum Package Quantity Packing Type Constitution Materials List RoHS TCOB1A476M8R TCOB 2000 2000 Taping inquiry Yes